Site to Site VPN between PIX and Linksys RV042
I am trying to create a tunnel between a 506th PIX and a Linksys RV042 vpn . I configured the Phase 1 and Phase 2 as well as the transformation defined and interested traffic and connected to the external interface, but it will not create the tunnel. Configurations are as follows:
506th PIX running IOS 6.3
part of pre authentication ISAKMP policy 40
ISAKMP policy 40 cryptographic 3des
ISAKMP policy 40 sha hash
40 2 ISAKMP policy group
ISAKMP duration strategy of life 40 86400
ISAKMP key * address 96.10.xxx.xxx netmask 255.255.255.255
access-list 101 permit ip 192.168.21.0 255.255.255.0 192.168.1.0 255.255.255.0crypto map Columbia_to_Office 10 ipsec-isakmp
crypto Columbia_to_Office 10 card matches the address 101
card crypto Columbia_to_Office 10 set peer 96.10.xxx.xxx
10 Columbia_to_Office transform-set ESP-3DES-SHA crypto card game
Columbia_to_Office interface card crypto outside
Linksys RV042
Configuration of local groups
IP only
IP address: 96.10.xxx.xxx
Type of local Security group: subnet
IP address: 192.168.1.0
Subnet mask: 255.255.255.0
Configuration of the remote control groups
IP only
IP address: 66.192.xxx.xxx
Security remote control unit Type: subnet
IP address: 192.168.21.0
Subnet mask: 255.255.255.0
IPSec configuration
Input mode: IKE with preshared key
Group Diffie-Hellman phase 1: group2
Phase 1 encryption: 3DES
Authentication of the phase 1: SHA1
Life of ITS phase 1: 86400
Phase2 encryption: 3DES
Phase2 authentication: SHA1
Phase2 life expectancy: 3600 seconds
Pre-shared key *.
I'm a novice on the VPN. Thanks in advance for your expertise.
Yes, version PIX 6.3 does not support HS running nat or sh run crypto.
Please please post the complete config if you don't mind.
Please also try to send traffic between subnets 2 and get the output of:
See the isa scream his
See the ipsec scream his
Tags: Cisco Security
Similar Questions
-
Troubleshooting IPSec Site to Site VPN between ASA and 1841
Hi all
in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.
I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).
I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.
It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),
On the ASA:
Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.
address of the peers: 217.86.154.120
Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.ccaccess extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
current_peer: 217.xx.yy.zz#pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz
Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
current outbound SPI: 39135054
current inbound SPI: B2E9E500SAS of the esp on arrival:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4374000/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
outgoing esp sas:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac no compression
running parameters = {L2L, Tunnel, PFS 2 group}
slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
calendar of his: service life remaining (KB/s) key: (4373976/1598)
Size IV: 8 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001Output of the command: "sh crypto isakmp his."
HIS active: 4
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 4IKE Peer: 217.xx.yy.zz
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVEOn the 1841
1841 crypto isakmp #sh its
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE1841 crypto ipsec #sh its
Interface: Dialer1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
Interface: virtual Network1
Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
current_peer 62.153.156.163 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
current outbound SPI: 0xB2E9E500 (3001672960)
PFS (Y/N): Y, Diffie-Hellman group: group2SAS of the esp on arrival:
SPI: 0 x 39135054 (957567060)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505068/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0xB2E9E500 (3001672960)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
calendar of his: service life remaining (k/s) key: (4505118/1306)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.
Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto. (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.
I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!
It's the running of the 1841 configuration
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
host name 1841
!
boot-start-marker
start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
boot-end-marker
!
logging buffered 51200 notifications
!
AAA new-model
!
!
AAA authentication login default local
!
AAA - the id of the joint session
!
iomem 20 memory size
clock timezone PCTime 1
PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
dot11 syslog
IP source-route
!
No dhcp use connected vrf ip
!
IP cef
no ip bootp Server
IP domain name test
name of the IP-server 194.25.2.129
name of the IP-server 194.25.2.130
name of the IP-server 194.25.2.131
name of the IP-server 194.25.2.132
name of the IP-server 194.25.2.133
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
object-group network phone
VoIP phone description
Home 172.20.2.50
Home 172.20.2.51
!
redundancy
!
!
controller LAN 0/0/0
atm mode
Annex symmetrical shdsl DSL-mode B
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
isakmp encryption key * address 62.aa.bb.cc
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to62.aa.bb.cc
the value of 62.aa.bb.cc peer
game of transformation-ESP-3DES-SHA
PFS group2 Set
match address 100
!
!
!
interface FastEthernet0/0
DMZ description $ FW_OUTSIDE$
10.10.10.254 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
!
interface FastEthernet0/1
Description $ETH - LAN$ $FW_INSIDE$
IP 172.20.2.254 255.255.255.0
IP access-group 100 to
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
ATM0/0/0 interface
no ip address
No atm ilmi-keepalive
!
point-to-point interface ATM0/0/0.1
PVC 1/32
PPPoE-client dial-pool-number 1
!
!
interface Dialer1
Description $FW_OUTSIDE$
the negotiated IP address
IP mtu 1452
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 2
PPP authentication chap callin pap
PPP chap hostname xxxxxxx
PPP chap password 7 xxxxxxx8
PPP pap sent-name of user password xxxxxxx xxxxxxx 7
map SDM_CMAP_1 crypto
!
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
!
!
The dns server IP
IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
!
logging trap notifications
Note category of access list 1 = 2 CCP_ACL
access-list 1 permit 172.20.2.0 0.0.0.255
Note access-list category 2 CCP_ACL = 2
access-list 2 allow 10.10.10.0 0.0.0.255
Note access-list 100 category CCP_ACL = 4
Note access-list 100 IPSec rule
access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
Note CCP_ACL the access list 101 = 2 category
Note access-list 101 IPSec rule
access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 101 permit ip 172.20.2.0 0.0.0.255 any
Note access-list 102 CCP_ACL category = 2
Note access-list 102 IPSec rule
access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
!!
allowed SDM_RMAP_1 1 route map
corresponds to the IP 101
!
allowed SDM_RMAP_2 1 route map
corresponds to the IP 102
!
!
control plan
!
!
Line con 0
line to 0
line vty 0 4
length 0
transport input telnet ssh
!
Scheduler allocate 20000 1000
NTP-Calendar Update
NTP 172.20.2.250 Server prefer
endAs I mentioned previously: suspicion is much appreciated!
Best regards
Joerg
Joerg,
ASA receives not all VPN packages because IOS does not send anything.
Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)
The problem seems so on the side of the router.
I think that is a routing problem, but you only have one default gateway (no other channels on the router).
The ACL 100 is set to encrypt the traffic between the two subnets.
It seems that the ACL 101 is also bypassing NAT for VPN traffic.
Follow these steps:
Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.
I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.
Federico.
-
Site to Site VPN between 5510 and 5505
Am trying to get a VPN site-to site and the race between a branch office and our main office. I have the settings in place, but I'm trying to determine if it's my settings or the provider DSL, Verizon.
They have a 5505 with a static IP is connected by cable modem. Their 5505 I can ping external IP of my 5510 without problem. All the settings are correct on both sides; they reflect the same settings and yet static VPN is not launched.
Is there some sort of CLI command I must issue to bring it?
Also, I was wondering if maybe my 2821 prevents all VPN traffic because it doesn't have to be re - NAT'ed to the 192.168.250.0/23 and 192.168.252.0/24 subnets.
Simply to traffic of their 192.168.40.0 in our 192.168.250.0/23 VOIP subnet subnet.
Join a basic outline. I can provide the configs for almost everything
Hello
you have two instances of sequence card crypto with parameters similar (except transform set). Get rid of the rest of sequences card crypto:
On the ASA Satellite:
no card crypto outside_map 2 match address outside_cryptomap
no card crypto outside_map 2 set pfs
no card crypto outside_map 2 peers set smivpn.sorensonmedia.com
no card crypto outside_map 2 the transform-set ESP-3DES-MD5 value
No crypto outside_map 2 set security-association life card seconds 28800
No kilobytes of life card crypto outside_map 2 set security-association 4608000
no card crypto outside_map 2 the value reverse-road
About the ASA company:
No crypto outside_map 1 game card address outside_1_cryptomap_1
no card crypto outside_map 1 set pfs
no card crypto outside_map 1 set cda.asa5505 counterpart
no card crypto outside_map 1 the value transform-set ESP-3DES-SHA
no card crypto outside_map 1 lifetime of security association set seconds 28800
No kilobytes of life card crypto outside_map 1 set security-association 4608000
no card crypto outside_map 1 the value reverse-road
Then check and capture debugs.
HTH
Sangaré
-
I have a vpn beteen two sites, which works very well. traffic is launched from site A and can connect to the site B ok.
I just tried to set up traffic from site B to site A, but its failure the vpn encrypt point. I checked the acl and they match:
site A (PIX)
Crypto acl
access-list site_a permit tcp host 10.51.3.32 10.0.0.0 255.0.0.0 eq 3389
no nat
no_nat list of allowed access host ip 10.51.3.32 10.0.0.0 255.0.0.0
site B (ASA)
Crypto acl
Site_B list extended access permitted tcp 10.0.0.0 255.0.0.0 host 10.51.3.32 eq 3389
no nat
access-list extended sheep allowed ip 10.0.0.0 255.0.0.0 10.51.3.32 host
the only difference I see is the extended acl, but it works well in one direction?
Thank you
Hello
Using port-based ACLs for crypto card is not recommended, use IP access lists and configure VPN filters to implement port restrictions.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Kind regards
Averroès
-
Problem with IPsec VPN between ASA and router Cisco - ping is not response
Hello
I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):
my network topology data:
LAN 1 connect ASA - 1 (inside the LAN)
PC - 10.0.1.3 255.255.255.0 10.0.1.1
ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0
-----------------------------------------------------------------
ASA - 1 Connect (LAN outide) R1
ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252
R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252
---------------------------------------------------------------------
R1 R2 to connect
R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252
R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252
R2 for lan connection 2
--------------------------------------------------------------------
R2 to connect LAN2
R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0
PC - 10.0.2.3 255.255.255.0 10.0.2.1
ASA configuration:
1 GigabitEthernet interface
nameif inside
security-level 100
IP 10.0.1.1 255.255.255.0
no downtime
interface GigabitEthernet 0
nameif outside
security-level 0
IP 172.30.1.2 255.255.255.252
no downtime
Route outside 0.0.0.0 0.0.0.0 172.30.1.1------------------------------------------------------------
access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
object obj LAN
subnet 10.0.1.0 255.255.255.0
object obj remote network
10.0.2.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static-----------------------------------------------------------
IKEv1 crypto policy 10
preshared authentication
aes encryption
sha hash
Group 2
life 3600
Crypto ikev1 allow outside
crypto isakmp identity address------------------------------------------------------------
tunnel-group 172.30.2.2 type ipsec-l2l
tunnel-group 172.30.2.2 ipsec-attributes
IKEv1 pre-shared-key cisco123
Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1-------------------------------------------------------------
card crypto ASA1VPN 10 is the LAN1 to LAN2 address
card crypto ASA1VPN 10 set peer 172.30.2.2
card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
card crypto ASA1VPN set 10 security-association life seconds 3600
ASA1VPN interface card crypto outsideR2 configuration:
interface fastEthernet 0/0
IP 10.0.2.1 255.255.255.0
no downtime
interface fastEthernet 0/1
IP 172.30.2.2 255.255.255.252
no downtime-----------------------------------------------------
router RIP
version 2
Network 10.0.2.0
network 172.30.2.0------------------------------------------------------
access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
access-list 102 permit esp 172.30.1.2 host 172.30.2.2
access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
interface fastEthernet 0/1
IP access-group 102 to------------------------------------------------------
crypto ISAKMP policy 110
preshared authentication
aes encryption
sha hash
Group 2
life 42300------------------------------------------------------
ISAKMP crypto key cisco123 address 172.30.1.2-----------------------------------------------------
Crypto ipsec transform-set esp - aes 128 R2TS------------------------------------------------------
access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255
------------------------------------------------------
R2VPN 10 ipsec-isakmp crypto map
match address 101
defined by peer 172.30.1.2
PFS Group1 Set
R2TS transformation game
86400 seconds, life of security association set
interface fastEthernet 0/1
card crypto R2VPNI don't know what the problem
Thank you
If the RIP is not absolutely necessary for you, try adding the default route to R2:
IP route 0.0.0.0 0.0.0.0 172.16.2.1
If you want to use RIP much, add permissions ACL 102:
access-list 102 permit udp any any eq 520
-
VPN between ASA and cisco router [phase2 question]
Hi all
I have a problem with IPSEC VPN between ASA and cisco router
I think that there is a problem in the phase 2
Can you please guide me where could be the problem.
I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified belowLooking forward for your help
Phase 1 is like that
Cisco_router #sh crypto isakmp his
IPv4 Crypto ISAKMP Security Association
status of DST CBC State conn-id slot
78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVEand ASA
ASA # sh crypto isakmp his
ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 11 peer IKE: 78.x.x.41
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVEPhase 2 on SAA
ASA # sh crypto ipsec his
Interface: Outside
Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
19.194.0 255.255.255.0
local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
current_peer: 78.x.x.41#pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
#send errors: 0, #recv errors: 0local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41
Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
current outbound SPI: C96393ABSAS of the esp on arrival:
SPI: 0x3E9D820B (1050509835)
transform: esp-3des esp-md5-hmac no
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 7, crypto-card: Outside_map
calendar of his: service life remaining (KB/s) key: (4275000/3025)
Size IV: 8 bytes
support for replay detection: Y
outgoing esp sas:
SPI: 0xC96393AB (3378746283)
transform: esp-3des esp-md5-hmac no
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 7, crypto-card: Outside_map
calendar of his: service life remaining (KB/s) key: (4274994/3023)
Size IV: 8 bytes
support for replay detection: YPhase 2 on cisco router
protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
current_peer 87.x.x.4 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
current outbound SPI: 0x0 (0)SAS of the esp on arrival:
the arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
outgoing ah sas:
outgoing CFP sas:
protégé of the vrf: (none)
local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
current_peer 87.x.x.4 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
Errors #send 0, #recv 0 errorslocal crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
current outbound SPI: 0x3E9D820B (1050509835)SAS of the esp on arrival:
SPI: 0xC96393AB (3378746283)
transform: esp-3des esp-md5-hmac.
running parameters = {Tunnel}
Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
calendar of his: service life remaining (k/s) key: (4393981/1196)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEthe arrival ah sas:
SAS of the CFP on arrival:
outgoing esp sas:
SPI: 0x3E9D820B (1050509835)
transform: esp-3des esp-md5-hmac.
running parameters = {Tunnel}
Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
calendar of his: service life remaining (k/s) key: (4394007/1196)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVEoutgoing ah sas:
outgoing CFP sas:
VPN configuration is less in cisco router
access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connectaccess-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connectsheep allowed 10 route map
corresponds to the IP 105Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset
mycryptomap 100 ipsec-isakmp crypto map
the value of 87.x.x.4 peer
Set transform-set mytransformset
match address 101crypto ISAKMP policy 100
BA 3des
md5 hash
preshared authentication
Group 2
ISAKMP crypto key xxx2011 address 87.x.x.4Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.
You currently have:
Extend the 105 IP access list
5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connectIt should be:
Extend the 105 IP access list
10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connectIP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)
To remove it and add it to the bottom:
105 extended IP access list
not 5
IP 172.19.194.0 allow 60 0.0.0.255 any
Then ' delete ip nat trans. "
and it should work now.
-
2 one-Site VPN between HQ, Site A and Site B
Dear brothers,
Really I need your kindly help on Site 2 Site VPN.
We have a HQ and 2 Sites (Site A Site & B), and we think to set up VPN Site-2-Site between them now.
HQ--> 3845 router (will be the hub)--> a given vlan 11 & vlan voice 21
Site A--> router 2901 (will be the Spoke1)--> a given vlan 12 & vlan voice 22
Site B--> router 1941 (will be the Spoke2)--> a given vlan 13 & vlan voice 23
So my questions are:
1 - when the VPN going up, are only the HQ VLAN data & voice will be able to reach the Site & A B data & Voice VLAN and Vice versa?
2 - when the VPN is going up, are that the Site has data & Voice VLAN will be able to reach the Site B Data & Voice VLAN and Vice versa?
Thank you
Hello
I think this example explains what you need:http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation...
Kind regards
Averroès.
-
IPSEC VPN between Pix 515E and 1841 router
Hi all
BACKGROUND
We have implemented a site to site VPN IPSEC between a Pix 515E 8.0 operation (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and the ASDM the pix to build initial tunnels. Now the site with the router is evolving into a dynamic IP address from the ISP so we have implemented dynamic DNS to update dynamic IP address.
PROBLEM
The problem is that ASDM will not allow us to set a domain as the address of peers, it will not accept an IP address. We believe that the solution will be to remove the static Crypto map and replace it with a dynamic Crypto map on the side of Pix. Our questions are simply; is this the best solution? can change us the original static list or is it better to delete and make a new dynamic encryption card? Y at - it a shortcut to change the config command-line? This is a real network, so just check it out before make us any changes on the live kit.
Any help much appreciated.
You don't have to change anything when the peer-address changes. The dynamic crypto map aims to take dynamic peer connections. The only thing to remember, is that only the dynamic peer can initiate the connection. And you reduce your security if you use Pre-Shared key that now you can use a generic-PSK character.
As I remember, the PIX / ASA does not support the dynamic use of FQDNs for peer-resolution. This feature is supported in IOS.
For a feature, it would be preferable to static IP addresses on both sides.
-
Site IPSec between RPS and IOS.
Hello
I really hope that Andrew Hickman, author of DOC-16927 and DOC-23028 can help with this.
I created a Site to IPSec VPN between our SRP527W-U and CISCO881-K9 (SRI) running IOS 15.0 (1) M3.
It is the first branch to use a PRV. I use a card dynamic encryption (that we have more than one branch, and ESP was a dynamic public IP address).
Our other branch (also runs an international search report) is a GRE over IPSec VPN, traffic between subnets it passes over the GRE tunnel. It works very well. The goal here is really to achieve the same (GRE over IPSec) between the SRP and the SRI. Similar to our other branch.
The ISAKMP and IPSec on SRI config:
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
ISAKMP crypto key SECRET KEY address 0.0.0.0 0.0.0.0
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
crypto dynamic-map DynMap1 10
game of transformation-ESP-3DES-SHA
PFS group2 Set
match address VPN
QoS before filing
card crypto 10 Vpn1-isakmp dynamic ipsec DynMap1
list of IP - VPN access scope
allow accord host
host ip permit 172.16.0.0 0.0.0.255 172.16.2.0 0.0.0.255
interface FastEthernet4
IP address
255.255.255.252 card crypto Vpn1
Router A - CISCO881-K9 (hub) Router B - SRP527W-U (speak) Network: 172.16.0.0/24 Network: 172.16.2.0/24 LAN IP: 172.16.0.1 LAN IP: 172.16.2.1 WAN IP: 203.174.188.58 WAN: Starting from a host in the 172.16.2.0/24 subnet, I ping SRI (172.16.0.1) and hosts on the 172.16.0.0/24, but not the PRS (172.16.2.1) under Diagnostics-> Ping Test.
Starting from a host on the subnet 172.16.0.0/24, I ping a host on the 172.16.2.0/24 network, but not the RPS (172.16.2.1). I can confirm SPI Firewall Protection is off and filter Internet requests anonymous check box is cleared.
While Sri (172.16.0.1), I can not ping RPS (172.16.2.1) or all the 172.16.2.0/24 subnet hosts.
Summary of Ping results
The host subnet a host <-->subnet B: Yes
A <-->B router the subnet host: No.
Router, the host of a-> B subnet: No.
Router a router <-->B: No.
Hosts on the subnet B-> A router: Yes
SRI routing table
* 0.0.0.0/0 [1/0] via
10.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks
C 10.0.0.0/24 is directly connected, Tunnel0
L 10.0.0.1/32 is directly connected, Tunnel0
172.16.0.0/16 is variably divided into subnets, 3 subnets, 2 masks
C 172.16.0.0/24 is directly connected, Vlan1
L 172.16.0.1/32 is directly connected, Vlan1
S 172.16.1.0/24 [1/0] via 10.0.0.2
The RPS routing table-->-->-->
10.64.64.74 255.255.255.255 -- ppp10 10.64.64.74 255.255.255.255 -- ipsec0 172.16.2.0 255.255.255.0 -- VLAN.1 172.16.0.0 255.255.255.0 10.64.64.74 ipsec0 0.0.0.0 0.0.0.0 10.64.64.74 ppp10 I suspect it's an ACL / route question. I would gladly of assistance from anyone. According to me, that I'm so close, just not there.
Thank you very much
Trent Renshaw
Hi Trent,
My apologies, I misread your first post - I thought that you were talking about the question of access and the IP address of the PRS via IPSec (that part is fixed).
I fear for your real question, there is no answer. The SRP500 does not support GRE over IPSec (just one or the other).
Kind regards
Andy
-
2 one-Site VPN Cisco 2801 and with crossing NAT
Hi guys,.
I would like to configure two Cisco 2801 using IPSEC/IKE. Both routers are connected to the internet through DSL lines. The DSL line have RFC1918 address side LAN where routers connected to the internet face. I can do NAT on DSL modems.
Cisco IOS 2801 routers allow to configure site-2-site VPN with NAT crossing?
Here is a model of physics/IP configuration:
LAN<->2801 Modem DSL<-Internet->DSL modem<-Priv ip-=""> 2801<-Priv ip-=""><-> LAN
Thank you
Gonçalo
Yes, you're good to go only if one or both of the sites has an IP address which is natted with private IP address statically. The implementation of IPSec on SRI NAT support in most crosses so that shouldn't be a concern
->-Priv>-Priv>-Internet->-> -
VPN between RV120W and ISA550W
Hi guys,.
Wonder if you can shed some light on my problem until I loose all my hair!
I'm trying to create a VPN between a RV120W at a remote site and our ISA500W in our offices... I can't it connect!
I'll put up an IPsec tunnel between the sites, but it does not want to connect.
Remote site - RV120W
The IKE policy table
Management / time type
Main mode Exchange
3DES encryption
AUTH - SHA-1
DH group 2
Pre-Shared Key AUTH
HIS life 28800
Xauth no
VPN
Type Auto policy
IP of remote endpoint address
Local IP subnet
Remote IP subnet
Auto policy settings
Life 3600 seconds
Encryption algorithm 3DES
SHA-1 integrity algorithm
Key Enable PFS group
DH-group 2 (1024 bits)
Headquarters - ISA550W
IPsec policy
Static IP address of remote Type
AUTH Type pre-shared Key
Local ID (empty)
Remote ID (empty)
IKE
SHA1 hash
Pre-shared Key
D0H group group 2 (1024 bits)
Lifetime 8 hours
Transform
integrity ESP_MD5_HMAC
Encryption ESP_3DES
Errors, I'm getting in the newspapers
Remote RV120W (note! I changed the external IP to protect the innocent!)
2013-10-29 14:39:20: [rv120w] [IKE] INFO: respond to the negotiation of the new phase 2: 69.193.0.0 [0]<=>80.4.0.0 [0]
2013-10-29 14:39:20: [rv120w] [IKE] INFO: configuration using IPsec SA: 192.168.3.0/24<->192.168.1.0/24
2013-10-29 14:39:20: [rv120w] [IKE] INFO: setting encmode 3 (3)-> Tunnel peer (1)
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: proposal of the peer:
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (proto_id = spisize ESP = 4 spi = spi_p 8846693d = encmode = 00000000 Tunnel reqid = 0:0)
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (trns_id = 3DES encklen = 0 authtype = hmac-md5)
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: Local proposal:
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (proto_id = spisize ESP = 4 spi = 00000000 spi_p 00000000 encmode = Tunnel reqid = 5:5 =)
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (trns_id = 3DES encklen = 0 authtype = hmac-sha)
2013-10-29 14:39:20: [rv120w] [IKE] WARNING: proposal for Phase 2 of 80.4.0.0 [0] does not.
2013-10-29 14:39:20: [rv120w] [IKE] ERROR: no adequate policy not found for 80.4.0.0 [0]
2013-10-29 14:39:20: [rv120w] [IKE] INFO: sending of information Exchange: Notify payload [NON-PROPOSITION-SELECTED]
2013-10-29 14:39:20: [rv120w] [IKE] INFO: purged-with proto_id = ISAKMP and spi = c8d68f74af9dfa9a:b4137fd6e0666914 ISAKMP Security Association.
2013-10-29 14:39:29: [rv120w] [IKE] INFO: accept a request to establish IKE - SA: 80.4.0.0
2013-10-29 14:39:29: [rv120w] [IKE] INFO: Configuration found for 80.4.0.0
2013-10-29 14:39:29: [rv120w] [IKE] INFO: opening new phase 1 negotiation: 69.193.0.0 [500]<=>80.4.0.0 [500]
2013-10-29 14:39:29: [rv120w] [IKE] INFO: Start Identity Protection mode.
2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:180]: XXX: NUMNATTVENDORIDS: 3
2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 4
2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 8
2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 9
2013-10-29 14:39:30: [rv120w] [IKE] INFO: received unknown Vendor ID
2013-10-29 14:39:30: [rv120w] [IKE] INFO: received Vendor ID: DPD
2013-10-29 14:39:30: [rv120w] [IKE] INFO: received Vendor ID: RFC 3947
2013-10-29 14:39:30: [rv120w] [IKE] INFO: for 80.4.0.0 [500], version selected NAT - T: RFC 3947
2013-10-29 14:39:30: [rv120w] [IKE] INFO: payload NAT - D corresponds to 69.193.0.0 [500]
2013-10-29 14:39:30: [rv120w] [IKE] INFO: NAT - D payload does not match for 80.4.0.0 [500]
2013-10-29 14:39:30: [rv120w] [IKE] INFO: NAT detected: PEER
2013-10-29 14:39:30: [rv120w] [IKE] INFO: for debugging: change ports2013-10-29 14:39:30: [rv120w] [IKE] INFO: change port!
2013-10-29 14:39:30: [rv120w] [IKE] INFO: received unknown Vendor ID=>->=>
2013-10-29 14:39:30: [rv120w] [IKE] INFO: ISAKMP Security Association established for 69.193.0.0 [4500] - 80.4.0.0 [4500] with spi: 740e6a59f02eca3a:820460c448a5b74b
2013-10-29 14:39:30: [rv120w] [IKE] INFO: sending of information Exchange: prevent the load [INITIAL CONTACT]
2013-10-29 14:39:31: [rv120w] [IKE] INFO: new phase 2 negotiation: 69.193.0.0 [500]<=>80.4.0.0 [0]
2013-10-29 14:39:31: [rv120w] [IKE] INFO: setting encryption mode to use UDP encapsulation
2013-10-29 14:39:31: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.=>
2013-10-29 14:39:41: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.
2013-10-29 14:39:51: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.
2013-10-29 14:40:01: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.
2013-10-29 14:40:02: [rv120w] [IKE] ERROR: Phase 2 negotiation failed due to upward. c8d68f74af9dfa9a:b4137fd6e0666914:f6cdeead
2013-10-29 14:40:02: [rv120w] [IKE] INFO: a calendar of undead has been removed: "quick_i1prep".
Head Office ISA550
2013-10-29 15:25:29 - WARNING - IPsec VPN: msg = "PixelNY" #4765: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
2013-10-29 15:25:29 - WARNING - IPsec VPN: msg = "PixelNY" #4765: max number of retransmissions (2) reached STATE_MAIN_I1. No answer (or no acceptable answer) to our first post IKE. (pluto)
2013-10-29 15:22:38 - WARNING - IPsec VPN: msg = "PixelNY" #4763: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
2013-10-29 15:22:38 - WARNING - IPsec VPN: msg = "PixelNY" #4763: max number of retransmissions (2) reached STATE_MAIN_I1. No answer (or no acceptable answer) to our first post IKE. (pluto)
2013-10-29 15:20:28 - WARNING - IPsec VPN: msg = "PixelNY" #4761: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
2013-10-29 15:20:28 - WARNING - IPsec VPN: msg = "PixelNY" #4761: max number of retransmissions (2) reached STATE_MAIN_I1. No answer (or no acceptable answer) to our first post IKE. (pluto)
2013-10-29 15:20:12 - WARNING - Firewall: type = ACL
If someone could shed some light it would be fantastic!
Configuration items you listed, it's what I see. Transformations do not match between the AIS and the change integrity RV RV MD5 or change the game to transform ISA SHA1. I would recommend changing the ISA in well SHA1As, you don't mention what is IKE ISA policy encryption, but there's 3DES in the RV, so you'll need to ensure its 3DES in ISA. Also note that you are life spans SA do not match. Technically, this should be ok, but it's really best to match as well. The ISA is 8 hours and the RV is 1 hour (3600 seconds)
Shawn Eftink
CCNA/CCDAPlease note all useful messages and mark the correct answers to help others looking for solutions in the community.
-
S - S VPN between ASA and ASR1001
Hello
We have 2 routers ASR to connected to ISP headquarters and there are new remote sites that must be connected to the AC over the site to site VPN. Each remote branch will be ASA, IPs outside of these two recommendations are in the same subnet.
1. is it possible to reach redudancy beside HQ in this design?
2. can I create L2L tunnels to two ASR? If yes how can I do 1 active tunnel and other secondary?
| ASR1
Users---L3SW---ASA---ISP---CPE---|
| ASR2
Any suggestions are welcome
Thank you
There are two ways:
- IPSec stateful failover
http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_vpnav/configuration/15-Mt/sec-VPN-availability-15-Mt-book/Sec-State-fail-IPSec.html
http://packetlife.net/blog/2009/Aug/17/fun-IPSec-stateful-failover/ - VPN config with two counterparts one ASA.
Here you have two individual bridges on the HQ and the ASA has two tunnel-groups en the two bridges but only a single sequence in the crypto plan. Peer education has two HQ - IPs configured.
- IPSec stateful failover
-
Routing over VPN between ISA550W and RV215W
Hello all I have a problem with the VPN between my two office
I have an ISA550W at the head office (chcnorth)
I have a RV215W to the remote desktop (chcsouth)
the VPN is up and running, I can connect from Headquarters to remote control (chcsouth-RV215W)
and vice versa however when client computers on the remote end are trying to connect to the
Main office to access the database, they can't.
the problem started last week I received a call from the remote desktop that they can connect to our database
on the main office, I tried to connect remotely to see what was going on, it turns out that the router has completely put back
at the plant, including the firmware
I reinstalled the latest firmware for the RV215W of installation all connections as they were, I could
get VPN to connect, I can ping to the interface of the RV215W from my seat and I ping the ISA550W
the remote desktop, however my remote clients still cannot access my server at the main office
I realized after I have everything set up, I had a backup of my original installation and thinking I had
just missed something I restored it to the firmware to factory upgraded to power and restored the backup of the
RV215W I've had. still no dice
So I am now at a loss, there were no other changes to the network on both ends, I've been on this som my eyes several times
are blurred,
any ideas, workarounds for solutions would be greatly appreciated
Thanks in advance
John G
John,
It doesn't look like your question is more DNS related, as you can access the server by its IP address if the "connection" allows you to set up this way. It is quite common, that you cannot resolve names through the tunnel because netbios broadcasts will not pass. The RV215W have shared DNS within the parameters of the tunnel, so this isn't an option more.
If the "connection" is a PC, you can work around this by editing the LMHOSTS file. Please see the following instructions:
http://www.JakeLudington.com/Windows_7/20100924_how_to_edit_windows_7_lmhosts_file.html
In your case, it might look more at:
192.168.1.200 sqlsvr
Now if you ping or try to access sqlsvr from the computer, it will automatically know that it should go to 192.168.1.200 without having to find the IP address.
Answer please if you have any questions.
-Marty
-
Hello
I'm setting up a VPN router between 871 and ASA 5505 for the first time and having a problem. I have attached my network diagram as well as the configuration of 871 and ASA. Although the VPN tunnel is coming for example sh crypto isakmp his watch QM_IDLE and Exchange ipsec SA is successuful as well, but none of the machine can access each other. Please help as I am in desperate need to operate.
Thank you all,.
Jérôme
Hello
It seems that you are missing some required configuration. See the link below...
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805e8c80.shtml
HTH
MS
* Rate of useful messages *.
-
LAN to lan vpn between ASA and router 7200
Hi friends,
I need to configure the lan to lan between ASA vpn (remote location) and router 7200 (on our network).
<7200 router="" (ip="" add:="" 10.10.5.2)="">-(Internet) -<(IP add:="" 192.168.12.2)="" asa(5510)="">---192.135.5.0/24 network
I will have the following configuration:
7200 router:
crypto ISAKMP policy 80
the enc
AUTH pre-shared
Group 1
life 3600
ISAKMP crypto key cisco123 address 192.168.12.2
Cryto ipsec transform-set esp - esp-md5-hmac VPNtrans
map VPNTunnel 80 ipsec-isakmp crypto
defined by peer 192.168.12.2
game of transformation-VPNtrans
match address 110
int fa0/0
IP add 10.10.5.2 255.255.255.192
IP virtual-reassembly
no ip route cache
Speed 100
full duplex
card crypto VPNTunnel
access-list 110 permit ip any 192.135.5.0 0.0.0.255
ASA:
int e0/0
nameif inside
security-level 100
192.135.5.254 Add IP 255.255.255.0
int e0/1
nameif outside
security-level 0
IP add 192.168.12.2 255.255.255.240
access-list ACL extended ip 192.135.5.0 allow 255.255.255.0 any
Route outside 0.0.0.0 0.0.0.0.0 192.168.12.3 1
"pre-shared key auth" ISAKMP policy 10
ISAKMP policy 10-enc
ISAKMP policy 10 md5 hash
10 1 ISAKMP policy group
ISAKMP duration strategy of life 10-3600
Crypto ipsec transform-set esp - esp-md5-hmac VPNtran
card crypto VPN 10 matches the ACL address
card crypto VPN 10 set peer 10.10.5.2
card crypto VPN 10 the transform-set VPNtran value
tunnel-group 10.10.5.2 type ipsec-l2l
IPSec-attributes of type tunnel-group 10.10.5.2
cisco123 pre-shared key
card crypto VPN outside interface
ISAKMP allows outside
dhcpd address 192.135.5.1 - 192.135.5.250 inside
dhcpd dns 172.15.4.5 172.15.4.6
dhcpd wins 172.15.76.5 172.15.74.5
dhcpd lease 14400
dhcpd ping_timeout 500
dhcpd allow inside
Please check the configuration, please correct me if I missed something. I'm in a critical situation at the moment...
Please advise...
Thank you very much...
Where it fails at the present time?
Can you share out of after trying to establish the VPN tunnel:
See the isa scream his
See the ipsec scream his
Please also run the following debug to see where it is a failure:
debugging cry isa
debugging ipsec cry
(IP>7200>
Maybe you are looking for
-
For a long time keep saying looks like to your using an older version of Firefox. Several times I tried to install Adobe Flash plug-in, both with Firefox and the Adobe site. I'm on Linux 32-bit, 64 no, details, that I find are for 64 bit. https://sup
-
HP envy 17 t k200 cto: hp envy 17 t k200 static on audio
Get the static background on audio and video playback. Playback is audible and understandable with a intermittent low grade in the background static. I used HP Support Assistant audio to check and it shows no problem. This book includes Beatsaudio, s
-
How to remove other then icon in the Notification list
Hello!!! Help I tried to remove the time and exe.at the bottom of my Notification list, but when I click on them they can be moved, so I drag my disktop to remove it. I tried to show them on the list of notifications to remove them, but nothing happe
-
How can I tell if Windows 8 will be compatible with my laptop - G71-340US?
-
0x800106b5 error code when you use Windows Defender
I tried to re - start after this error code, but when you run Defender again, same error code came.