Site to Site VPN between 5510 and 5505

Similar Questions

• Troubleshooting IPSec Site to Site VPN between ASA and 1841

  Hi all

  in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.

  I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).

  I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.

  It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),

  On the ASA:

  Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.

  address of the peers: 217.86.154.120
  Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.cc

  access extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
  local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
  current_peer: 217.xx.yy.zz

  #pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: 39135054
  current inbound SPI: B2E9E500

  SAS of the esp on arrival:
  SPI: 0xB2E9E500 (3001672960)
  transform: esp-3des esp-sha-hmac no compression
  running parameters = {L2L, Tunnel, PFS 2 group}
  slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
  calendar of his: service life remaining (KB/s) key: (4374000/1598)
  Size IV: 8 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0x00000000 0x00000001
  outgoing esp sas:
  SPI: 0 x 39135054 (957567060)
  transform: esp-3des esp-sha-hmac no compression
  running parameters = {L2L, Tunnel, PFS 2 group}
  slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
  calendar of his: service life remaining (KB/s) key: (4373976/1598)
  Size IV: 8 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0x00000000 0x00000001

  Output of the command: "sh crypto isakmp his."

  HIS active: 4
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 4

  IKE Peer: 217.xx.yy.zz
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  On the 1841

  1841 crypto isakmp #sh its
  IPv4 Crypto ISAKMP Security Association
  DST CBC conn-State id
  217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE

  1841 crypto ipsec #sh its

  Interface: Dialer1
  Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
  current_peer 62.153.156.163 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
  current outbound SPI: 0xB2E9E500 (3001672960)
  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:
  SPI: 0 x 39135054 (957567060)
  transform: esp-3des esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
  calendar of his: service life remaining (k/s) key: (4505068/1306)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xB2E9E500 (3001672960)
  transform: esp-3des esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
  calendar of his: service life remaining (k/s) key: (4505118/1306)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  Interface: virtual Network1
  Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
  current_peer 62.153.156.163 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
  current outbound SPI: 0xB2E9E500 (3001672960)
  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:
  SPI: 0 x 39135054 (957567060)
  transform: esp-3des esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
  calendar of his: service life remaining (k/s) key: (4505068/1306)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xB2E9E500 (3001672960)
  transform: esp-3des esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
  calendar of his: service life remaining (k/s) key: (4505118/1306)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.

  Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto.      (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.

  I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!

  It's the running of the 1841 configuration

  !
  version 15.1
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host name 1841
  !
  boot-start-marker
  start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
  boot-end-marker
  !
  logging buffered 51200 notifications
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  !
  AAA - the id of the joint session
  !
  iomem 20 memory size
  clock timezone PCTime 1
  PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
  dot11 syslog
  IP source-route
  !
  No dhcp use connected vrf ip
  !
  IP cef
  no ip bootp Server
  IP domain name test
  name of the IP-server 194.25.2.129
  name of the IP-server 194.25.2.130
  name of the IP-server 194.25.2.131
  name of the IP-server 194.25.2.132
  name of the IP-server 194.25.2.133
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  object-group network phone
  VoIP phone description
  Home 172.20.2.50
  Home 172.20.2.51
  !
  redundancy
  !
  !
  controller LAN 0/0/0
  atm mode
  Annex symmetrical shdsl DSL-mode B
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  isakmp encryption key * address 62.aa.bb.cc
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  map SDM_CMAP_1 1 ipsec-isakmp crypto
  Description Tunnel to62.aa.bb.cc
  the value of 62.aa.bb.cc peer
  game of transformation-ESP-3DES-SHA
  PFS group2 Set
  match address 100
  !
  !
  !
  interface FastEthernet0/0
  DMZ description $ FW_OUTSIDE$
  10.10.10.254 IP address 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  automatic duplex
  automatic speed
  !
  interface FastEthernet0/1
  Description $ETH - LAN$ $FW_INSIDE$
  IP 172.20.2.254 255.255.255.0
  IP access-group 100 to
  IP nat inside
  IP virtual-reassembly
  IP tcp adjust-mss 1412
  automatic duplex
  automatic speed
  !
  ATM0/0/0 interface
  no ip address
  No atm ilmi-keepalive
  !
  point-to-point interface ATM0/0/0.1
  PVC 1/32
  PPPoE-client dial-pool-number 1
  !
  !
  interface Dialer1
  Description $FW_OUTSIDE$
  the negotiated IP address
  IP mtu 1452
  NAT outside IP
  IP virtual-reassembly
  encapsulation ppp
  Dialer pool 1
  Dialer-Group 2
  PPP authentication chap callin pap
  PPP chap hostname xxxxxxx
  PPP chap password 7 xxxxxxx8
  PPP pap sent-name of user password xxxxxxx xxxxxxx 7
  map SDM_CMAP_1 crypto
  !
  IP forward-Protocol ND
  IP http server
  local IP http authentication
  IP http secure server
  !
  !
  The dns server IP
  IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
  IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
  IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
  IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
  IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
  !
  logging trap notifications
  Note category of access list 1 = 2 CCP_ACL
  access-list 1 permit 172.20.2.0 0.0.0.255
  Note access-list category 2 CCP_ACL = 2
  access-list 2 allow 10.10.10.0 0.0.0.255
  Note access-list 100 category CCP_ACL = 4
  Note access-list 100 IPSec rule
  access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
  Note CCP_ACL the access list 101 = 2 category
  Note access-list 101 IPSec rule
  access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
  access-list 101 permit ip 172.20.2.0 0.0.0.255 any
  Note access-list 102 CCP_ACL category = 2
  Note access-list 102 IPSec rule
  access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
  access-list 102 permit ip 10.10.10.0 0.0.0.255 any
  !

  !
  allowed SDM_RMAP_1 1 route map
  corresponds to the IP 101
  !
  allowed SDM_RMAP_2 1 route map
  corresponds to the IP 102
  !
  !
  control plan
  !
  !
  Line con 0
  line to 0
  line vty 0 4
  length 0
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  NTP-Calendar Update
  NTP 172.20.2.250 Server prefer
  end

  As I mentioned previously: suspicion is much appreciated!

  Best regards

  Joerg

  Joerg,

  ASA receives not all VPN packages because IOS does not send anything.

  Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)

  The problem seems so on the side of the router.

  I think that is a routing problem, but you only have one default gateway (no other channels on the router).

  The ACL 100 is set to encrypt the traffic between the two subnets.

  It seems that the ACL 101 is also bypassing NAT for VPN traffic.

  Follow these steps:

  Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.

  I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.

  Federico.

• Site to Site VPN between Cisco ASA 5505 and Sonicwall TZ170

  I'm trying to implement a VPN site-to site between our data center and office.  The data center has a Cisco ASA 5505 and the Office has a Sonicwall TZ170.  I managed to configure the two so that the vpn connects.  Each of the firewall I ping the IP Address of the internet firewall on the other side and a desktop computer I can ping the IP Address of the firewall internal datacenter but I can't carry traffic between private subnets datacenter and desktop.  Can anyone help?

  The config below has had IPs/passwords has changed.

  External Datacenter: 1.1.1.4

  External office: 1.1.1.1

  Internal data center: 10.5.0.1/24

  Internal office: 10.10.0.1/24

  : Saved
  :
  ASA Version 8.2 (1)
  !
  hostname datacenterfirewall
  mydomain.tld domain name
  activate the password encrypted
  passwd encrypted
  names of
  name 10.10.0.0 OfficeNetwork
  10.5.0.0 DatacenterNetwork name
  !
  interface Vlan1
  nameif inside
  security-level 100
  10.5.0.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  1.1.1.4 IP address 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS server-group DefaultDNS
  buydomains.com domain name
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  inside_access_in list extended access permit icmp any one
  inside_access_in list extended access permitted tcp a whole
  inside_access_in list extended access udp allowed a whole
  inside_access_in of access allowed any ip an extended list
  outside_access_in list extended access permit icmp any one
  outside_access_in list extended access udp allowed any any eq isakmp
  IP DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0
  IP OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0
  outside_cryptomap_66.1 list of allowed ip extended access all OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 ip OfficeNetwork 255.255.255.0 allowed extended access list all
  outside_cryptomap_66.1 list extended access permit icmp any OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 list extended access allowed icmp OfficeNetwork 255.255.255.0 everything
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP verify reverse path to the outside interface
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route inside 0.0.0.0 0.0.0.0 1.1.1.1 1
  Route OfficeNetwork 255.255.255.0 outside 1.1.1.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 10.5.0.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-aes-256 walthamoffice, esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto dynamic-map ciscopix 1 corresponds to the address outside_cryptomap_66.1
  Crypto dynamic-map ciscopix 1 transform-set walthamoffice
  Crypto dynamic-map ciscopix 1 the value reverse-road
  map dynmaptosw 66-isakmp ipsec crypto dynamic ciscopix
  dynmaptosw interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 13
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  lifetime 28800
  crypto ISAKMP policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  Telnet 10.5.0.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 10.5.0.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd address 10.5.0.2 - 10.5.0.254 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 66.250.45.2 source outdoors
  NTP server 72.18.205.157 source outdoors
  NTP server 208.53.158.34 source outdoors
  WebVPN
  attributes of Group Policy DfltGrpPolicy
  VPN-idle-timeout no
  username admin password encrypted
  tunnel-group 1.1.1.1 type ipsec-l2l
  tunnel-group 1.1.1.1 ipsec-attributes
  pre-shared-key *.
  !
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  !
  context of prompt hostname
  Cryptochecksum:7f319172e5de9c0e550804a263f8e49e
  : end

  Mattew, obvious lack of education is the rule exempt from nat for your tunnel, your access list pixtosw is similar on this example, I assume that you have gone through this link, if it does not see the configs on both sides.

  Add the statement of rule sheep in asa and try again.

  NAT (inside) 0-list of access pixtosw

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008052c9d4.shtml

  Concerning

• Site to Site VPN between PIX and Linksys RV042

  I am trying to create a tunnel between a 506th PIX and a Linksys RV042 vpn .  I configured the Phase 1 and Phase 2 as well as the transformation defined and interested traffic and connected to the external interface, but it will not create the tunnel.  Configurations are as follows:

  506th PIX running IOS 6.3

  part of pre authentication ISAKMP policy 40
  ISAKMP policy 40 cryptographic 3des
  ISAKMP policy 40 sha hash
  40 2 ISAKMP policy group
  ISAKMP duration strategy of life 40 86400
  ISAKMP key * address 96.10.xxx.xxx netmask 255.255.255.255
  access-list 101 permit ip 192.168.21.0 255.255.255.0 192.168.1.0 255.255.255.0crypto map Columbia_to_Office 10 ipsec-isakmp
  crypto Columbia_to_Office 10 card matches the address 101
  card crypto Columbia_to_Office 10 set peer 96.10.xxx.xxx
  10 Columbia_to_Office transform-set ESP-3DES-SHA crypto card game
  Columbia_to_Office interface card crypto outside

  Linksys RV042

  Configuration of local groups
  IP only
       IP address: 96.10.xxx.xxx
  Type of local Security group: subnet
  IP address: 192.168.1.0
  Subnet mask: 255.255.255.0

  Configuration of the remote control groups
  IP only
  IP address: 66.192.xxx.xxx
  Security remote control unit Type: subnet
  IP address: 192.168.21.0
  Subnet mask: 255.255.255.0

  IPSec configuration
  Input mode: IKE with preshared key
  Group Diffie-Hellman phase 1: group2
  Phase 1 encryption: 3DES
  Authentication of the phase 1: SHA1
  Life of ITS phase 1: 86400
     
  Phase2 encryption: 3DES
  Phase2 authentication: SHA1
  Phase2 life expectancy: 3600 seconds
  Pre-shared key *.

  I'm a novice on the VPN. Thanks in advance for your expertise.

  Yes, version PIX 6.3 does not support HS running nat or sh run crypto.

  Please please post the complete config if you don't mind.

  Please also try to send traffic between subnets 2 and get the output of:

  See the isa scream his

  See the ipsec scream his

• Problem with IPsec VPN between ASA and router Cisco - ping is not response

  Hello

  I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

  my network topology data:

  LAN 1 connect ASA - 1 (inside the LAN)

  PC - 10.0.1.3 255.255.255.0 10.0.1.1

  ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

  -----------------------------------------------------------------

  ASA - 1 Connect (LAN outide) R1

  ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

  R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

  ---------------------------------------------------------------------

  R1 R2 to connect

  R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

  R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

  R2 for lan connection 2

  --------------------------------------------------------------------

  R2 to connect LAN2

  R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

  PC - 10.0.2.3 255.255.255.0 10.0.2.1

  ASA configuration:

  1 GigabitEthernet interface
  nameif inside
  security-level 100
  IP 10.0.1.1 255.255.255.0
  no downtime
  interface GigabitEthernet 0
  nameif outside
  security-level 0
  IP 172.30.1.2 255.255.255.252
  no downtime
  Route outside 0.0.0.0 0.0.0.0 172.30.1.1

  ------------------------------------------------------------

  access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
  object obj LAN
  subnet 10.0.1.0 255.255.255.0
  object obj remote network
  10.0.2.0 subnet 255.255.255.0
  NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

  -----------------------------------------------------------
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 3600
  Crypto ikev1 allow outside
  crypto isakmp identity address

  ------------------------------------------------------------
  tunnel-group 172.30.2.2 type ipsec-l2l
  tunnel-group 172.30.2.2 ipsec-attributes
  IKEv1 pre-shared-key cisco123
  Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

  -------------------------------------------------------------
  card crypto ASA1VPN 10 is the LAN1 to LAN2 address
  card crypto ASA1VPN 10 set peer 172.30.2.2
  card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
  card crypto ASA1VPN set 10 security-association life seconds 3600
  ASA1VPN interface card crypto outside

  R2 configuration:

  interface fastEthernet 0/0
  IP 10.0.2.1 255.255.255.0
  no downtime
  interface fastEthernet 0/1
  IP 172.30.2.2 255.255.255.252
  no downtime

  -----------------------------------------------------

  router RIP
  version 2
  Network 10.0.2.0
  network 172.30.2.0

  ------------------------------------------------------
  access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
  access-list 102 permit esp 172.30.1.2 host 172.30.2.2
  access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
  interface fastEthernet 0/1
  IP access-group 102 to

  ------------------------------------------------------
  crypto ISAKMP policy 110
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 42300

  ------------------------------------------------------
  ISAKMP crypto key cisco123 address 172.30.1.2

  -----------------------------------------------------
  Crypto ipsec transform-set esp - aes 128 R2TS

  ------------------------------------------------------

  access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

  ------------------------------------------------------

  R2VPN 10 ipsec-isakmp crypto map
  match address 101
  defined by peer 172.30.1.2
  PFS Group1 Set
  R2TS transformation game
  86400 seconds, life of security association set
  interface fastEthernet 0/1
  card crypto R2VPN

  I don't know what the problem

  Thank you

  If the RIP is not absolutely necessary for you, try adding the default route to R2:

  IP route 0.0.0.0 0.0.0.0 172.16.2.1

  If you want to use RIP much, add permissions ACL 102:

  access-list 102 permit udp any any eq 520

• VPN between ASA and cisco router [phase2 question]

  Hi all

  I have a problem with IPSEC VPN between ASA and cisco router

  I think that there is a problem in the phase 2

  Can you please guide me where could be the problem.
  I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

  Looking forward for your help

  Phase 1 is like that

  Cisco_router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

  and ASA

  ASA # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 78.x.x.41
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  Phase 2 on SAA

  ASA # sh crypto ipsec his
  Interface: Outside
  Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

  Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
  19.194.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer: 78.x.x.41

  #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C96393AB

  SAS of the esp on arrival:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4275000/3025)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4274994/3023)
  Size IV: 8 bytes
  support for replay detection: Y

  Phase 2 on cisco router

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x0 (0)

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x3E9D820B (1050509835)

  SAS of the esp on arrival:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4393981/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4394007/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  VPN configuration is less in cisco router

  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  sheep allowed 10 route map
  corresponds to the IP 105

  Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

  mycryptomap 100 ipsec-isakmp crypto map
  the value of 87.x.x.4 peer
  Set transform-set mytransformset
  match address 101

  crypto ISAKMP policy 100
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key xxx2011 address 87.x.x.4

  Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

  You currently have:

  Extend the 105 IP access list
  5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  It should be:

  Extend the 105 IP access list
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

  To remove it and add it to the bottom:

  105 extended IP access list

  not 5

  IP 172.19.194.0 allow 60 0.0.0.255 any

  Then ' delete ip nat trans. "

  and it should work now.

• 2 one-Site VPN between HQ, Site A and Site B

  Dear brothers,

  Really I need your kindly help on Site 2 Site VPN.

  We have a HQ and 2 Sites (Site A Site & B), and we think to set up VPN Site-2-Site between them now.

  HQ--> 3845 router (will be the hub)--> a given vlan 11 & vlan voice 21

  Site A--> router 2901 (will be the Spoke1)--> a given vlan 12 & vlan voice 22

  Site B--> router 1941 (will be the Spoke2)--> a given vlan 13 & vlan voice 23

  So my questions are:

  1 - when the VPN going up, are only the HQ VLAN data & voice will be able to reach the Site & A B data & Voice VLAN and Vice versa?

  2 - when the VPN is going up, are that the Site has data & Voice VLAN will be able to reach the Site B Data & Voice VLAN and Vice versa?

  Thank you

  Hello

  I think this example explains what you need:http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation...

  Kind regards

  Averroès.

• Site to Site VPN ASA 5510

  OK my forehead is painful to all keyboard strokes that I know that it must be something simple, but I am brand new to the SAA.  I had a site to site VPN configuration via routers 1751 that worked very well, but we're looking to add some more remote field offices, and I felt that it would be easier to maintain several sites is on the ASA 5510.  I have the VPN configured on the SAA and he said that the tunnel is up.  I can telnet to the ASA and ping the remote gateway on the even side of VPN and it pings fine.  If I try to ping on a local computer, I get a "Request timed out".  If I makes no changes apart from go to the computer room and replace the network cable the 1751 and then through the 1751 I can now ping the remote door way to my computer.  The remote router works obviously very well, my statement of route on my router for vpn push through the ASA (same ip address) IP traffic that has been used by the 1751 works obviously. It seems so just like ASA is not being pushed in the ethernet0/0 VPN traffic or at least it is not encrypted.  I also noticed that the ACL for NAT seems to increase in number of access either it seems, there is really just one small thing missing to make the ASA except and encrypt incoming traffic on ethernet0/0:

  My network is not configured with a DMZ is something like that, the ASA ethernet0/0 and my local network on the same subnet:

  Router (Cisco 2811)

  |

  Layer switch 2 (ProCurve)

  |                                      |

  ASA5510 LAN computers

  I'm trying to except both sides of the VPN in and out on Ethernet0/0 traffic I saw there was a framework for this "permit communication between VPN peers connected to the same interface' and I've activated this option.

  In short, I need to understand why the VPN tunnel shows that upward and I can ping the remote of the SAA, but peripheral gateway on my network can not ping to the remote gateway through the int Ethernet0/0 on the SAA.

  From the console of the ASA, I get this:

  ASA5510 # ping 192.52.128.1
  Send 5, echoes ICMP 100 bytes to 192.52.128.1, wait time is 2 seconds:
  !!!!!
  Success rate is 100 per cent (5/5), round-trip min/avg/max = 100/108/120 ms

  ASA5510 # show crypto ipsec his
  Interface: *.
  Tag crypto map: * _map, local addr: 10.52.120.23

  local ident (addr, mask, prot, port): (10.52.120.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.52.128.0/255.255.255.0/0/0)
  current_peer: x.x.x.204

  program #pkts: 9, #pkts encrypt: 9, #pkts digest: 9
  decaps #pkts: 9, #pkts decrypt: 9, #pkts check: 9
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 9, #pkts comp failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 10.52.120.23, remote Start crypto. : x.x.x.204

  Path mtu 1500, fresh ipsec generals 60, media, mtu 1500
  current outbound SPI: C49EF75F

  SAS of the esp on arrival:
  SPI: 0x21FDBB9D (570276765)
  transform: esp-3des esp-md5-hmac
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 1, crypto-map: * _map
  calendar of his: service life remaining (KB/s) key: (3824999/3529)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC49EF75F (3298752351)
  transform: esp-3des esp-md5-hmac
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 1, crypto-map: * _map
  calendar of his: service life remaining (KB/s) key: (3824999/3527)
  Size IV: 8 bytes
  support for replay detection: Y

  From my office on the 10.52.120.0 even the etherenet0/0 interface on the ASA network I get this:

  C:\Users\***>ping 192.52.128.1

  Ping 192.52.128.1 with 32 bytes of data:
  Request timed out.
  Request timed out.
  Request timed out.
  Request timed out.

  Ping statistics for 192.52.128.1:
  Packets: Sent = 4, received = 0, lost = 4 (100% loss)

  C:\Users\***>ping 10.52.120.23

  Ping 10.52.120.23 with 32 bytes of data:
  Reply from 10.52.120.23: bytes = 32 time = 5ms TTL = 255
  Reply from 10.52.120.23: bytes = 32 time = 3ms TTL = 255
  Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255
  Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255

  Ping statistics for 10.52.120.23:
  Packets: Sent = 4, received = 4, lost = 0 (0% loss),
  Time approximate round trip in milli-seconds:
  Minimum = 1ms, Maximum = 5ms, average = 2ms

  Count on VPN Tunnel ACL does not increase when I try to ping the address of the remote gateway.

  Here is the running of the ASA configuration:

  ASA Version 7.0 (2)
  names of
  !
  interface Ethernet0/0
  nameif InsideNetwork
  security-level 100
  IP 10.52.120.23 255.255.255.0
  !
  interface Ethernet0/1
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  management only
  !
  activate the encrypted password of XXXXXXXXXXXXXXXX
  passwd encrypted XXXXXXXXXXXXXXXXXXX
  ciscoasa hostname
  domain default.domain.invalid
  passive FTP mode
  permit same-security-traffic intra-interface
  Access extensive list ip 10.52.120.0 InsideNetwork_nat0_outbound allow 255.255.25
  5.0 192.52.128.0 255.255.255.0
  Access extensive list ip 10.52.120.0 InsideNetwork_cryptomap_20 allow 255.255.255
  .0 192.52.128.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  management of MTU 1500
  MTU 1500 InsideNetwork
  management of the interface of the monitor
  the interface of the monitor InsideNetwork
  ASDM image disk0: / asdm - 502.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (InsideNetwork) 0-list of access InsideNetwork_nat0_outbound
  Route InsideNetwork 0.0.0.0 0.0.0.0 10.52.120.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00
  Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 10.52.120.0 255.255.255.0 InsideNetwork
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  card crypto InsideNetwork_map 20 corresponds to the address InsideNetwork_cryptomap_20
  card crypto InsideNetwork_map 20 set peer x.x.x.204
  InsideNetwork_map 20 transform-set ESP-3DES-MD5 crypto card game
  InsideNetwork_map InsideNetwork crypto map interface
  ISAKMP enable InsideNetwork
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  Telnet 10.52.120.0 255.255.255.0 InsideNetwork
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  dhcpd lease 3600
  dhcpd ping_timeout 50
  enable dhcpd management
  tunnel-group x.x.x.204 type ipsec-l2l
  x.x.x.204 group of tunnel ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  Policy-map global_policy
  class inspection_default
  inspect the dns-length maximum 512
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  Cryptochecksum:7e478b60b3e406091de466675c52eaaa
  : end

  I haven't added anything to the config except what seemed necessary to get the job of VPN tunnel.  It should be fairly clean.

  Thanks in advance for any help... I really hope that it is something really simple as a recruit ASA just forgot

  Strange, but good news. Thanks for the update. I'm glad everything is working.

  THX

  MS

• Site IPSec between RPS and IOS.

  Hello

  I really hope that Andrew Hickman, author of DOC-16927 and DOC-23028 can help with this.

  I created a Site to IPSec VPN between our SRP527W-U and CISCO881-K9 (SRI) running IOS 15.0 (1) M3.

  It is the first branch to use a PRV. I use a card dynamic encryption (that we have more than one branch, and ESP was a dynamic public IP address).

  Our other branch (also runs an international search report) is a GRE over IPSec VPN, traffic between subnets it passes over the GRE tunnel. It works very well. The goal here is really to achieve the same (GRE over IPSec) between the SRP and the SRI. Similar to our other branch.

  The ISAKMP and IPSec on SRI config:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key SECRET KEY address 0.0.0.0 0.0.0.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  crypto dynamic-map DynMap1 10

  game of transformation-ESP-3DES-SHA

  PFS group2 Set

  match address VPN

  QoS before filing

  card crypto 10 Vpn1-isakmp dynamic ipsec DynMap1

  list of IP - VPN access scope

  allow accord host host

  ip permit 172.16.0.0 0.0.0.255 172.16.2.0 0.0.0.255

  interface FastEthernet4

  IP address 255.255.255.252

  card crypto Vpn1

  Router A - CISCO881-K9 (hub)	Router B - SRP527W-U (speak)
  Network: 172.16.0.0/24	Network: 172.16.2.0/24
  LAN IP: 172.16.0.1	LAN IP: 172.16.2.1
  WAN IP: 203.174.188.58	WAN:

  Starting from a host in the 172.16.2.0/24 subnet, I ping SRI (172.16.0.1) and hosts on the 172.16.0.0/24, but not the PRS (172.16.2.1) under Diagnostics-> Ping Test.

  Starting from a host on the subnet 172.16.0.0/24, I ping a host on the 172.16.2.0/24 network, but not the RPS (172.16.2.1). I can confirm SPI Firewall Protection is off and filter Internet requests anonymous check box is cleared.

  While Sri (172.16.0.1), I can not ping RPS (172.16.2.1) or all the 172.16.2.0/24 subnet hosts.

  Summary of Ping results

  The host subnet a host <-->subnet B: Yes

  A <-->B router the subnet host: No.

  Router, the host of a-> B subnet: No.

  Router a router <-->B: No.

  Hosts on the subnet B-> A router: Yes

  SRI routing table

  * 0.0.0.0/0 [1/0] via

  10.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks

  C 10.0.0.0/24 is directly connected, Tunnel0

  L 10.0.0.1/32 is directly connected, Tunnel0

  172.16.0.0/16 is variably divided into subnets, 3 subnets, 2 masks

  C 172.16.0.0/24 is directly connected, Vlan1

  L 172.16.0.1/32 is directly connected, Vlan1

  S 172.16.1.0/24 [1/0] via 10.0.0.2

  The RPS routing table

  10.64.64.74	255.255.255.255	--	ppp10
  10.64.64.74	255.255.255.255	--	ipsec0
  172.16.2.0	255.255.255.0	--	VLAN.1
  172.16.0.0	255.255.255.0	10.64.64.74	ipsec0
  0.0.0.0	0.0.0.0	10.64.64.74	ppp10

  I suspect it's an ACL / route question. I would gladly of assistance from anyone. According to me, that I'm so close, just not there.

  Thank you very much

  Trent Renshaw

  Hi Trent,

  My apologies, I misread your first post - I thought that you were talking about the question of access and the IP address of the PRS via IPSec (that part is fixed).

  I fear for your real question, there is no answer.  The SRP500 does not support GRE over IPSec (just one or the other).

  Kind regards

  Andy

• 2 one-Site VPN Cisco 2801 and with crossing NAT

  Hi guys,.

  I would like to configure two Cisco 2801 using IPSEC/IKE. Both routers are connected to the internet through DSL lines. The DSL line have RFC1918 address side LAN where routers connected to the internet face. I can do NAT on DSL modems.

  Cisco IOS 2801 routers allow to configure site-2-site VPN with NAT crossing?

  Here is a model of physics/IP configuration:

  LAN<->2801 Modem DSL<-Internet->DSL modem<-Priv ip-=""> 2801<-Priv ip-=""><-> LAN

  Thank you

  Gonçalo

  Yes, you're good to go only if one or both of the sites has an IP address which is natted with private IP address statically. The implementation of IPSec on SRI NAT support in most crosses so that shouldn't be a concern

• VPN between RV120W and ISA550W

  Hi guys,.

  Wonder if you can shed some light on my problem until I loose all my hair!

  I'm trying to create a VPN between a RV120W at a remote site and our ISA500W in our offices... I can't it connect!

  I'll put up an IPsec tunnel between the sites, but it does not want to connect.

  Remote site - RV120W

  The IKE policy table

  Management / time type

  Main mode Exchange

  3DES encryption

  AUTH - SHA-1

  DH group 2

  Pre-Shared Key AUTH

  HIS life 28800

  Xauth no

  VPN

  Type Auto policy

  IP of remote endpoint address

  Local IP subnet

  Remote IP subnet

  Auto policy settings

  Life 3600 seconds

  Encryption algorithm 3DES

  SHA-1 integrity algorithm

  Key Enable PFS group

  DH-group 2 (1024 bits)

  Headquarters - ISA550W

  IPsec policy

  Static IP address of remote Type

  AUTH Type pre-shared Key

  Local ID (empty)

  Remote ID (empty)

  IKE

  SHA1 hash

  Pre-shared Key

  D0H group group 2 (1024 bits)

  Lifetime 8 hours

  Transform

  integrity ESP_MD5_HMAC

  Encryption ESP_3DES

  Errors, I'm getting in the newspapers

  Remote RV120W (note! I changed the external IP to protect the innocent!)

  2013-10-29 14:39:20: [rv120w] [IKE] INFO: respond to the negotiation of the new phase 2: 69.193.0.0 [0]<=>80.4.0.0 [0]

  2013-10-29 14:39:20: [rv120w] [IKE] INFO: configuration using IPsec SA: 192.168.3.0/24<->192.168.1.0/24

  2013-10-29 14:39:20: [rv120w] [IKE] INFO: setting encmode 3 (3)-> Tunnel peer (1)

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: proposal of the peer:

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (proto_id = spisize ESP = 4 spi = spi_p 8846693d = encmode = 00000000 Tunnel reqid = 0:0)

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (trns_id = 3DES encklen = 0 authtype = hmac-md5)

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: Local proposal:

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (proto_id = spisize ESP = 4 spi = 00000000 spi_p 00000000 encmode = Tunnel reqid = 5:5 =)

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: (trns_id = 3DES encklen = 0 authtype = hmac-sha)

  2013-10-29 14:39:20: [rv120w] [IKE] WARNING: proposal for Phase 2 of 80.4.0.0 [0] does not.

  2013-10-29 14:39:20: [rv120w] [IKE] ERROR: no adequate policy not found for 80.4.0.0 [0]

  2013-10-29 14:39:20: [rv120w] [IKE] INFO: sending of information Exchange: Notify payload [NON-PROPOSITION-SELECTED]

  2013-10-29 14:39:20: [rv120w] [IKE] INFO: purged-with proto_id = ISAKMP and spi = c8d68f74af9dfa9a:b4137fd6e0666914 ISAKMP Security Association.

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: accept a request to establish IKE - SA: 80.4.0.0

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: Configuration found for 80.4.0.0

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: opening new phase 1 negotiation: 69.193.0.0 [500]<=>80.4.0.0 [500]

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: Start Identity Protection mode.

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:180]: XXX: NUMNATTVENDORIDS: 3

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 4

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 8

  2013-10-29 14:39:29: [rv120w] [IKE] INFO: [ident_i1send:184]: XXX: definition of vendorid: 9

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: received unknown Vendor ID

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: received Vendor ID: DPD

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: received Vendor ID: RFC 3947

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: for 80.4.0.0 [500], version selected NAT - T: RFC 3947

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: payload NAT - D corresponds to 69.193.0.0 [500]

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: NAT - D payload does not match for 80.4.0.0 [500]

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: NAT detected: PEER

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: for debugging: change ports2013-10-29 14:39:30: [rv120w] [IKE] INFO: change port!

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: received unknown Vendor ID

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: ISAKMP Security Association established for 69.193.0.0 [4500] - 80.4.0.0 [4500] with spi: 740e6a59f02eca3a:820460c448a5b74b

  2013-10-29 14:39:30: [rv120w] [IKE] INFO: sending of information Exchange: prevent the load [INITIAL CONTACT]

  2013-10-29 14:39:31: [rv120w] [IKE] INFO: new phase 2 negotiation: 69.193.0.0 [500]<=>80.4.0.0 [0]

  2013-10-29 14:39:31: [rv120w] [IKE] INFO: setting encryption mode to use UDP encapsulation

  2013-10-29 14:39:31: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.

  2013-10-29 14:39:41: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.

  2013-10-29 14:39:51: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.

  2013-10-29 14:40:01: [rv120w] [IKE] ERROR: Unknown notify message from the 80.4.0.0 [4500]. No found handful of phase2.

  2013-10-29 14:40:02: [rv120w] [IKE] ERROR: Phase 2 negotiation failed due to upward. c8d68f74af9dfa9a:b4137fd6e0666914:f6cdeead

  2013-10-29 14:40:02: [rv120w] [IKE] INFO: a calendar of undead has been removed: "quick_i1prep".

  Head Office ISA550

  2013-10-29 15:25:29 - WARNING - IPsec VPN: msg = "PixelNY" #4765: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)

  2013-10-29 15:25:29 - WARNING - IPsec VPN: msg = "PixelNY" #4765: max number of retransmissions (2) reached STATE_MAIN_I1.  No answer (or no acceptable answer) to our first post IKE. (pluto)

  2013-10-29 15:22:38 - WARNING - IPsec VPN: msg = "PixelNY" #4763: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)

  2013-10-29 15:22:38 - WARNING - IPsec VPN: msg = "PixelNY" #4763: max number of retransmissions (2) reached STATE_MAIN_I1.  No answer (or no acceptable answer) to our first post IKE. (pluto)

  2013-10-29 15:20:28 - WARNING - IPsec VPN: msg = "PixelNY" #4761: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)

  2013-10-29 15:20:28 - WARNING - IPsec VPN: msg = "PixelNY" #4761: max number of retransmissions (2) reached STATE_MAIN_I1.  No answer (or no acceptable answer) to our first post IKE. (pluto)

  2013-10-29 15:20:12 - WARNING - Firewall: type = ACL

  If someone could shed some light it would be fantastic!

  Configuration items you listed, it's what I see.  Transformations do not match between the AIS and the change integrity RV RV MD5 or change the game to transform ISA SHA1.  I would recommend changing the ISA in well SHA1As, you don't mention what is IKE ISA policy encryption, but there's 3DES in the RV, so you'll need to ensure its 3DES in ISA.  Also note that you are life spans SA do not match.  Technically, this should be ok, but it's really best to match as well.  The ISA is 8 hours and the RV is 1 hour (3600 seconds)

  Shawn Eftink
  CCNA/CCDA

  Please note all useful messages and mark the correct answers to help others looking for solutions in the community.

• ASA 5505 - I can't create an IPSEC VPN between two ASA 5505

  Hello

  I have two ASA 5505 with basic license and I'm trying to create a VPN IPSEC using the CLI. Here are the steps I did:

  1 Configure ASA-1 (host name, vlan 1 and vlan 2).

  2. configure a static route

  3. create object network (local and remote)

  4. create the access list

  5. create ikev1 crypto

  6. create tunnel-group

  7 Configure nat

  and I repeat the steps above with the ASA but another change IP.

  Are to correct the above steps?

  Why can I not create an IPSEC VPN between devices?.

  No, you needn't. The ASA configuration is ok. Packet trace proved it. I think it can be a problem on the hosts. Please, check the firewall on the PC and try to put out of service, if it is running.

• VPN between ASA and 871

  Hello

  I'm setting up a VPN router between 871 and ASA 5505 for the first time and having a problem. I have attached my network diagram as well as the configuration of 871 and ASA. Although the VPN tunnel is coming for example sh crypto isakmp his watch QM_IDLE and Exchange ipsec SA is successuful as well, but none of the machine can access each other. Please help as I am in desperate need to operate.

  Thank you all,.

  Jérôme

  Hello

  It seems that you are missing some required configuration. See the link below...

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805e8c80.shtml

  HTH

  MS

  * Rate of useful messages *.

• S - S VPN between ASA and ASR1001

  Hello

  We have 2 routers ASR to connected to ISP headquarters and there are new remote sites that must be connected to the AC over the site to site VPN. Each remote branch will be ASA, IPs outside of these two recommendations are in the same subnet.

  1. is it possible to reach redudancy beside HQ in this design?

  2. can I create L2L tunnels to two ASR? If yes how can I do 1 active tunnel and other secondary?

  | ASR1

  Users---L3SW---ASA---ISP---CPE---|

  | ASR2

  Any suggestions are welcome

  Thank you

  There are two ways:

  1. IPSec stateful failover
     http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_conn_vpnav/configuration/15-Mt/sec-VPN-availability-15-Mt-book/Sec-State-fail-IPSec.html
     http://packetlife.net/blog/2009/Aug/17/fun-IPSec-stateful-failover/
  2. VPN config with two counterparts one ASA.
     Here you have two individual bridges on the HQ and the ASA has two tunnel-groups en the two bridges but only a single sequence in the crypto plan. Peer education has two HQ - IPs configured.

• LAN to lan vpn between ASA and router 7200

  Hi friends,

  I need to configure the lan to lan between ASA vpn (remote location) and router 7200 (on our network).

  <7200 router="" (ip="" add:="" 10.10.5.2)="">-(Internet) -<(IP add:="" 192.168.12.2)="" asa(5510)="">---192.135.5.0/24 network

  I will have the following configuration:

  7200 router:

  crypto ISAKMP policy 80

  the enc

  AUTH pre-shared

  Group 1

  life 3600

  ISAKMP crypto key cisco123 address 192.168.12.2

  Cryto ipsec transform-set esp - esp-md5-hmac VPNtrans

  map VPNTunnel 80 ipsec-isakmp crypto

  defined by peer 192.168.12.2

  game of transformation-VPNtrans

  match address 110

  int fa0/0

  IP add 10.10.5.2 255.255.255.192

  IP virtual-reassembly

  no ip route cache

  Speed 100

  full duplex

  card crypto VPNTunnel

  access-list 110 permit ip any 192.135.5.0 0.0.0.255

  ASA:

  int e0/0

  nameif inside

  security-level 100

  192.135.5.254 Add IP 255.255.255.0

  int e0/1

  nameif outside

  security-level 0

  IP add 192.168.12.2 255.255.255.240

  access-list ACL extended ip 192.135.5.0 allow 255.255.255.0 any

  Route outside 0.0.0.0 0.0.0.0.0 192.168.12.3 1

  "pre-shared key auth" ISAKMP policy 10

  ISAKMP policy 10-enc

  ISAKMP policy 10 md5 hash

  10 1 ISAKMP policy group

  ISAKMP duration strategy of life 10-3600

  Crypto ipsec transform-set esp - esp-md5-hmac VPNtran

  card crypto VPN 10 matches the ACL address

  card crypto VPN 10 set peer 10.10.5.2

  card crypto VPN 10 the transform-set VPNtran value

  tunnel-group 10.10.5.2 type ipsec-l2l

  IPSec-attributes of type tunnel-group 10.10.5.2

  cisco123 pre-shared key

  card crypto VPN outside interface

  ISAKMP allows outside

  dhcpd address 192.135.5.1 - 192.135.5.250 inside

  dhcpd dns 172.15.4.5 172.15.4.6

  dhcpd wins 172.15.76.5 172.15.74.5

  dhcpd lease 14400

  dhcpd ping_timeout 500

  dhcpd allow inside

  Please check the configuration, please correct me if I missed something. I'm in a critical situation at the moment...

  Please advise...

  Thank you very much...

  Where it fails at the present time?

  Can you share out of after trying to establish the VPN tunnel:

  See the isa scream his

  See the ipsec scream his

  Please also run the following debug to see where it is a failure:

  debugging cry isa

  debugging ipsec cry