slow Flash

Similar Questions

• Satellite A200 - slow flash cards

  I have a Toshiba A200 1s 5 laptop with Vista Home Premium pre-installed. C2D [email protected], 2 GB of RAM.

  The problem is that the utility flash cards is very slow. It takes a long time from when I press the FN button until the cards appear. In addition, the slow short utility. Sometimes it won't appear even. I understand that you really need these flash cards to use the function keys without which they will not work.

  Are there any known issues with this utility or do I just try put it back? I have this problem since I bought the laptop and I never have a relocation or recovery. Thus, all the software that came with it are original.

  Excuse my bad English.

  Hello

  We know that the previous version is quite slow. Toshiba has offered the new version and now it works quickly. Please remove preinstalled value-added Package and install the latest version you will find on the download page of Toshiba.

  Good bye

• Slow flashing red in 3500 Series Microsoft wireless mouse

  Original title: my mouse is weird

  I have a small (3500 version) Microsoft wireless mouse and I just put a new battery in there and all I get is a red light flashing slow... the battery is good... I tested it... any help would be greatly appreciated.  It's probably something really stupid that I'm missing, but I hate that touchpad and I take courses online and rely heavily on the mouse to avoid mistakes... Help!

  Hi Jane,

  There are many reasons why we have a flashing red light on a Microsoft wireless mouse. The mouse software may need an update, you're battery may need to be replaced or recharged, you're wireless device can be connected to a port is non-functional, something can interfere with the wireless mouse.

  Here are some tips you can follow and see if that helps.

  1. download and install the latest drivers for mouse depending on the type of computer http://www.microsoft.com/hardware/en-us/p/wireless-mobile-mouse-3500#support system

  2 a wireless device may interfere with each other. Look at the bottom of your mouse to see if it has a button to synchronize with the receiver. If Yes, press this button. In so doing resync the mouse using a different channel. Turn the receiver upside down or on its side to see if you are able to get a better connection. Remove the other wireless devices, such as a wireless or a cell phone and make sure that the mouse is located at a distance of at least eight inches of a wireless keyboard. Make sure that the mouse is not on a very close to metal objects or metal surface.

  3 try using a mouse instead of using it on a glassy or metallic surface.

  4. ensure that the batteries are inserted correctly. Open battery compartment. Check and remove anything that might obstruct the battery connection. Search corrosion as well and remove, if possible.

  I hope this helps.

• Very slow flash in FF player

  Firefox: 16.0.1
  Flash player: 11.4

  -During the run in safe mode
  -Latest video drivers

  When on a youtube video, I can move the mouse around the buttons and it will take about 3 seconds for the mouse to travel between the buttons. The same phenomenon occurs on the BBC News site.

  All other flash videos seem to work correctly.

  Watch youtube/BBC news in IE works fine. Currently, the FF is unusable for these Web sites.

  This also happens in safe mode.

  You can check the problems caused by the recent updates of Flash and try these:

  • disable an eventual extension of the browser for Firefox Plugin RealPlayer Record and if installed RealPlayer update
  • disable the safe_mode in Flash 11.3 and later versions
  • turn off hardware acceleration in the Flash plugin
  • http://KB.mozillazine.org/Flash#troubleshooting

• HP ProBook 470 G2: Stop slower / flashing power button / stop...

  Hello

  Ive got a G2 HP 470 here with a weird problem, whenever stop you the laptop, you see windows stops, and then the screen goes black (full black, as when it is turned off) but the power button (white) and a orange led near the AC connector Flash like for 10 seconds before the laptop shuts down completely.

  I've updated all the drivers and BIOS.  but without success...

  Battery removed etc, but also without success...

  Someone knows how to fix this or is something broken?

  Best regards

  Hello

  Try disabling the startup of Windows 10 hybrid - you can do the following.

  Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

  In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close open windows and stop the laptop by right clicking on the icon from the Start Menu, select prompt (Admin) and click 'Yes' to the uac prompt.

  Type (or copy and paste) the following command (including spaces) and click Enter.

  Shutdown /s /t 0

  Start the laptop and let Windows take over completely for a few minutes before checking if she will now disable correctly.

  If this has fixed the problem, it may be useful by turning the quick start back on - sometimes simply remove and re-create the file will solve the problem.

  Kind regards

  DP - K

• Slow and not meet in order to be inapplicable last week

  Two weeks ago, that I started to see a window that does not match my boot password. Nothing more. No idea what password was now emerging as incorrect. Click OK and everything went forth. I think it had to do with the SYNCHRONIZATION. Then in the past week, since Monday, may 25, 2015, it is incredibly slow, flashing, fogs and sends messages "Firefox is not responding.

  I tried Chrome, works very well. Tried Explorer on my work machine, very good. Not a problem of Internet service provider. Not a machine problem. It comes to Firefox and with all that has changed, it makes the browser unusable. I suspect it has to do with the synchronization because it is noticed change. Hope you'll get fixed soon. I appreciate the security of FF. I'll keep checking back, but so far no improvement. Thanks in advance.

  Hi deerpath15, if please see if Firefox is slow after upgrading to Firefox 38 applies to your situation and can solve the problem.

• screen flashes

  Pavilion hp my girlfreind 15 running windows 8.1 the screen keeps flashing. It starts normal and you sigh and then the screen flashes always the icons on the windows of office white stay, the taskbar keeps reloading and you can't open all but if you do shut down when it flashes again. I managed to open the windows update and I ran the update he had a program and that it intstalled. I have restraed and it keeps flashing. I tried to change it did nothing to refresh rate but the slow flashing. He has norton on it so I don't think it's a virus, but I couldn't say for sure I can't run it. I need help

  Hi Dtr2694,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP Pavilion Notebook of 15 and get a blank screen or black at startup. Try perform a reset. When you perform a hard reset note remove all USB devices and remove cards memory card reader location. Disconnect all non-essential devices. If that doesn't help try to turn on the computer, on which you begin to press F11 repeatedly until the menu opens. You can do a System Restore.

  Hope it will be useful.

  Thank you.

• Why this flash drive cannot be used for loan boost in windows 7?

  I have a flash drive 8 GB Kingston which is useless, but functional. I decided to use it to boost lending. So, when I go to ready boost in windows 7, it says this drive cannot be used as ready boost I've tried several times but the same answer. When I try to use it as ready boost preview of consumer windows it says OK. I have set up as ready boost. I also format and then try but same answer in windows 7. How can I use this disk as ready boost in windows 7?

  Sometimes the reader is not fast enough for Readyboost. BTW: How much memory you have in your PC? You can even no need for ReadyBoost.

  But, to force Windows to use ReadyBoost (even with a slow flash drive): http://www.mstechpages.com/2010/10/12/force-readyboost-on-a-usb-device/

• Sony a6000 Wireless Flash

  I do not understand how a w/l flash works on a6000 sony... the built-in flash works as a controller or I need some external hardware

  The problem is that the built-in flash on the body of the E mount is very low (GEN 4 to 6) due to the low battery (1080 mAh) compared to the built-in flash on the body of the mount (GEN 10 to 12) with their larger (1600 mAh) battery.

  It is also why the E-Mount has a relatively slow flash sync speed and no high-speed synchronization.

  You should also know that this is not something that can be fixed with a firmware update. The small battery just can't handle.

• SPA-2100 continues to Flash.

  Hi all

  After receiving the SPA-2100, I have a problem with it. SPA-2100 more return as ATA.

  He seems to be in this stadium and never comes out:

  Slow flashing (0.5 sec ON, continues to 0.5 s OFF)
  

  • Initialization of the system; only occurs at the start of the SPA-maximum, time could be as long as 10 seconds (hardware reboot) to two seconds (warm start).
  • Firmware for download.
  • Looking for a DHCP.

  Other symptoms are:

  (1) the yellow and green lights (lights status, line1, line2, Wan and Wan) anti-terrorism Act keeps blinking once power is connected (with no other cable is connected). I tried to unplug and "the rest" of the anti-terrorism Act and then reconnect the power supply but the yellow and green status lights never "stabilizes" and will continue to Flash intermittently.
  (2) for the ATA WAN is connected directly to my router Lan port and ATA PC port connected to my laptop it reports that the cycles there after disconnected and network connection for limited available ("connection to the LAN - a network cable is unplugged") on the same cycle as the yellow of the ATA and the green light of connectivity LAN of the modem and the status indicators indicate.
  (4) listen to the connected analog phone you can't hear any sound feedback through the earpiece. Also no command doesn't seem to work. (*, etc.)

  I hope that this device is still noticeable feasible.

  Thank you

  Matt,

  I hate to say this man, but it seems (after view it) as if this device is toast. Where do you have, how long have you had, did you contact the HWC (866-606-1866) to support this topic, and when did this start happening? If you obtained it from a VoIP provider, then you must contact them for a new unit. If the unit was purchased by you, you can provide the serial number for the center of assistance to small businesses for a possible rma. If you have had more time that the hardware warranty is, then you will need to buy another camera. The link on each ethernet port lights should not be on unless there is an active connection at the other end. It seems that the unit is locked in its ' cycle (POST) start and won't boot. Good luck.

  Bill

• Prroblems export. Flash CS5 MOV files

  I can't export my animations created in Flash CS5 (Macromedia flash 5 or CS3) to MOV files. I'm having these issues on different platforms (mac and pc) and operating systems (XP and win 7)-I get that error and error messages memory, even on the computer the fastest I have with 4gig of RAM works on a Flash of 2 mg file.
  
  I want to just convert my Flash files into a format that can play on Youtube and standard DVD players. Also I tried several converters (flash video) - not all free (Moyea, Roxio, iWisoft, Winfx Video Converter, Amor, E.M. Magic, etc, etc)-nothing works. The main problems are either the sound is not synchronized, playback is choppy and the quality is terrible.
  
  I think my only hope to get a good video starts with a good. Exported from Flash MOV file. I know that the program is supposed to do.
  Any help much appreciated.

  http://help.Adobe.com/en_US/Flash/CS/using/WSBC0687D4-42A6-445D-B5FF-8032C7D3A8FF.html#WS6 A15AAE2-C176-4161-BAB6-FB082F63B65Ba

  SOLUTION to choppy/laggy video.  I'm tired of it and it works. some changes outside of Flash Pro is required.

  Play the animation in Flash Pro (in the main screen, press enter). During playback, watching the loacted framerate below the timeline.  You will see that there are not constant.  Slots with more scripts/symbols will slow the fps, and the animation appears restless.  These points will also be restless in the Mov (coincidence? hmm...).

  The export in Flash Pro transcribe * frameworks *, rather he plays the Flash movie and saves it as a camcorder.  These moments of slowdown stirred in the Mov are not the result of Quicktime video playback, they are integrated into the film itself (you can see in picture-jumping through the first video).

  SOLUTION TO THE RESTLESS MOV FORMAT:

  • Either:-understand the slower that cadence lights during playback from the timeline OR

  -play it safe and just choose a ridiculously low fps (I chose 5)

  • Export the movie at this pace (set both the chronology and the export of 5 dialog box)
  • You will find yourself with a video image with very slow, but the point is that it will be same.  Slow Flash gives enough time between the images to load symbols and deal with scripts, without making a specific frame slower than others.
  • Import it in Premiere/Final Cut and accelerate up to the correct speed.  It is now smooth and uniform.
  • Copy the original audio in the first
  • Export the Filmstrip

• How to reset the airport extreme to factory default

  My Airport & time capsule are not connected to the modem, saying no dns server is available, however the modem works when connected to the computer. (Macbook) After hours of troubleshooting, I would just restore default settings and see if I can get it going again. Can anyone provide info on restoring the default settings?

  Thank you!

  • Turning off AirPort Extreme for a minute or two
  • In the reset button on the back of the AirPort Extreme first... and keep taking them for 7 to 8 seconds... while simultaneously you reconnect the power on the AirPort Extreme.  (This step is a bit complicated for most users, because it takes almost 3 hands to do it properly)
  • Release the reset button to zero after the period of detention and allow a minute for the AirPort Extreme back on the way to a slow, flashing amber light status

  AirPort Extreme is now back to the State it was when you took it first out of the box.

• Airport Time Capsule re - install

  Hi all. I had an accident on my Time Capsule airport and were not able to access it from.  The capsule was repaired, but my computer no longer recognizes.  Also, when I try to access, it requires a password that will be years and I don't remember.  Then, I tried the soft, hard and reset procedures listed in the support area and none of them work effectively.  I'm supposed to get a yellow light flashing rapid when the hard or factory is completed.  I only get the usual slow flashing yellow, and nothing has changed when trying to gain access through the time capsule.  I tried to go through utilities the utilities from the airport, without success.  Can anyone offer any other suggestions?

  I'm supposed to get a yellow light flashing rapid when the hard or factory is completed.  I only get the usual slow flashing yellow and nothing has changed when trying to gain access through the time capsule

  If the time Capsule was lit for a few minutes and you hold in the reset button on the back of the time Capsule 7 to 8 seconds... and that the light orange do not start blinking quickly after a few seconds to hold the reset button... then the reset button does not work... maybe because a small spacer was dislodged when the Capsule was opened for repairs.

  Resume time Capsule and have the shop the reset button fix.

• USB HDD TRAY 1, 5 t: = red light drive lights works very slowly

  Hello

  It is brand new USB STORE 1, 5 t 3.5 "disk.

  Drive normally begins with the red light, initialize and move to blue light. Initially drive works slow - flashing blue when something happens.

  ... but after a few minutes of use, red light may turn on a moment (for e.g. when new folder is created or some files are copied - then drive works very slowly - it appears when you copy).

  After a few seconds, record going to the blue back light - and everything is OK until the switch next to the red.

  1 is this normal behavior?
  2. What is the meaning of red light when the drive is working?

  Thank you in advance.

  Hello

  I m no owner of this HARD but I have a theory.
  According to your information, I think that the red light only appears if data would be written to the HARD disk.
  The blue light appears during the reading of data from the HARD drive.

  Welcome them

• Satellite Pro 6100 stops after 15-30 minutes

  My satellite Pro 6100 Cup after 15 to 30 minutes of operation on power outlet. There is a noise and all the lights go out except orange slow flashing (power problem). I have restore by removing the power cable and wait a while.

  It will then start again. I used two different adapters and two different batteries. It also happens if work on AC with no battery in the. My suspicion is an overheat cut-out. The Sat Pro has a? Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in. Advice much appreciated. Thank you.

  > Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in
  I agree with you and the user SambadeAmigo. It seems like a simple problem of overheating and so the laptop automatically stops to prevent the equipment from damage

  I assume that your laptop can be enabled again after being allowed to cool. It is a common question if the cooling modules may not work properly because of the dust and debris.
  As suggested, it would be possible to remove dust using the can of compressed air.
  It should work.

  See you soon