Software Magentic

Similar Questions

• HP Photosmart C6180 Magenta Ink not printing

  error message: no

  description of the problem: Magenta Ink not print not EXCEPT on the page that prints after aligning the print cartridge printing is performed. At the bottom of this page, the bars of yellow, Cyan and Magenta print perfectly, just like the mixture of the color shown in the colorful bird printed below the bars.

  Self Test Diagnostic Page is printed with bars No. Light Magenta or Magenta, under print quality model. State of ink and level for both shows like OK magenta and 100%

  Troubleshooting: I ran repeated cycles of head cleaning and aligning the print cartridge print without changing the output. The page that prints after cleaning has NO magenta bars or lines. Seems the page that prints after alignment. Via e-mail support, I was directed to perform a complete reset "semi" and "the NVM reset" - neither of these had no effect. Magenta inks have been replaced, but the problem persists.

  Exchange: the printer had not been used for several months.

  My printer started working. It had been disconnected and sitting for several months. I turned it to try the HP solutions (below) and found that it worked - I had nothing to do!  In any case, I hope this can help some of you with similar problems:

  Hello
  
  Thank you for contacting HP Total Care.
  
  I'm Vivian of HP Total care for all-in-One products, and this response is in what regards the problem with HP Photosmart C6180 all-in-One Printer.
  
  Of your mail, I understand you have a HP Photosmart C6180 all-in-One Printer. Currently, you have a problem in which the printer prints in magenta only on the alignment page and not even on the test page.
  
  I am aware of the importance of the issue and will give you the appropriate information. I need your cooperation and appreciate your efforts to resolve the issue.
  
  First of all I want to thank you for the link, I'll take that as a feedback and will forward it to the concerned Department. However it is not a known, issue because in this case, HP will take immediate action and make sure that defective cartridges do not reach the market.
  
  Please try the following troubleshooting steps. I assure you that those measures would solve the problem.
  
  I ask you to check if you have the same problem with the copy as function. If the printer copy very well magenta do not perform one of the steps given and please get back to us for further assistance. However if you encounter the same problem with the copy as well please continue with the provided steps.
  
  First step: clean the copper contacts.
  
  (1) take a lint cloth or a cotton ball, it wet with water.
  (2) clean the cartridge copper contacts.
  (3) you have the same type of copper on the printer also, contacts if you are able to reach their own contacts in copper on the printer also.
  (4) reinstall the cartridge in its housing.
  (5) when the printer is on, unplug the power cord from the printer.
  (6) press and hold the power button for about 30 seconds.
  (7) re plug the power cord into the printer and the printer.
  
  If the problem persists, proceed to the next step.
  
  Step 2: Perform a drain of power on the printer.
  
  (1) remove the power cord from the product
  (2) press and hold the power button for about a minute (while the power cord is not connected to the printer).
  (3) release the button.
  (4) connect the power cord to the product
  (5) use the button to turn the product on.
  
  Connect the printer to the computer and check; If the problem persists, proceed to the next step.
  
  Step 3: Reset the printer to the factory settings.
  
  (1) use the button to turn the product on.
  (2) remove the power cord from the product
  (3) press and hold the # and 6 buttons.
  (4) while now buttons, plug the power cord to the product
  (5) to continue to press the buttons for about 30 seconds.
  (6) use the button to turn the product on.
  (7) if these steps do not resolve the problem, it will be a hardware problem with the printer in this case I suggest you take the printer to the nearest authorized Service Provider for the service.
  
  Please follow these steps and get back to us with the results, if you need more help, please reply to this message and we will be happy to help you further.
  
  We look forward to hear from you.
  
  For more information on keep your HP and Compaq products up and running, please visit our Web site at:
  
  http://www.HP.com/go/TotalCare

  ALSO:

  If the printer performs the color copy and you get magenta on the copy, it is obvious that the printer works fine, it's a software problem. I ask you to try the following steps, depending on your convenience and get back to us with the results.
  
  First step: reset the printing system
  
  To use the reset printing system feature, follow these steps:
  
  1. in the Finder, choose utilities from the menu reach.
  2. open the printer setup utility.
  3. in the printer setup utility menu, choose Reset Printing System.
  4. click on reset.
  
  Second step: check/repair disk permissions
  
  Click on Go tab in the top menu bar.
  Select the utilities tab.
  Click disk utility.
  Once disk utility appears, select the drive and click the check permissions.
  
  This can take a long time to complete as the Mac will try to check all permissions to the hard drive.
  Now click on the tab authorization to repair disc.
  
  This can take a long time to complete as the Mac will try to repair all permissions to the hard drive.
  Once Permission to disk check is complete, restart the Mac
  
  Step 3: Add the printer again
  
  1. click the Apple on the top of the left hand button.
  2. click on Preferences system, window system preferences will open.
  3. click on the printers and faxes icon.
  4. click on add the symbol on the bottom of the left hand.
  5. you see your printer in the list, select it and click Add on the right side.
  
  Please, do the following and get home with the results, for further assistance please get back to us, we will be happy to help you.
  For more information on keep your HP and Compaq products up and running, please visit our Web site
  to:
  http://www.HP.com/go/TotalCare

• DeskJet F2180: Deskjet F2180 only magenta work.

  The printer worked very well for many years. I upgraded to WIN 10 and he stiil worked. It works well in black but has a problem in color mode. I thought it was a problem of low ink as only magenta worked. I tried another cartridge that had the same problem, but it was an old cartridge and thought it might have dried. Then I bought a new cartridge (HP22) real and the problem resolved. The print cartridge allignment sheet and complete alignment. After a few weeks, one of the colors is impossible to print. I cleaned the contacts, but it made no difference. I then printed a self-test as described in the manual and all three colors print correctly. I checked that win 10 is up-to-date and I reinstalled the latest HP driver. Is there a diagnostic software that will help you.

  Glad to hear that you guessed it sorted. There is no such reclassification policy non HP cartridges. Perhaps you are referring to this: inquiries regarding third party ink and supplies (recharge and revised).

  In any case, this does not apply to your printer, and I think the question was probably related to the software or driver, and I am pleased that you guessed it work.

• LaserJet CP1525nw: CP1525nw color printer leaves magenta spots to the left of each page

  My CP1525nw color printer leaves the magenta veins on the left side of each page to print.  I tried to clean the printer using the clean function built into many times I removed and cleaned the amgenta cartridge, and I also deleted every piece of software my machine HP and reinstalled the drivers for this printer.  Magenta strekas are still there. They are always on the left side of the page.

  someone had this problem a few years ago and an answering machine seems to have responded with a link to a wrong page

  Is there a solution or a work link pleaase?

  Well, it's obvious that you're upset.  I'd be for.  To make this real simple.  You have a bad magenta toner cartridge. Cleaning will not work because the wiper inside the toner cartridge blade went probably bad toner causing the flight of this side and causing the problem.  Replace the magenta toner with a new toner hp original and all should be good.

• Printer does not print need to update driver of Magenta - Lexmark

  Original title: printer does not print Magenta

  I have an old Lexmark printer. I just installed new toner and it won't print magenta. I downloaded a new driver from the Lexmark Web site supposedly and yet, it will not be printed. I can't find the old driver anywhere, through each directory on the computer. Windows Help doesn't help. Told you to follow the instructions of the manufacturer. Manufacturer tells you first uninstall the old driver. Windows Help doesn't tell you how to uninstall the drivers.

  When I contacted Windows /Dell they pass the buck to Lexmark. Lexmark passes the ball to Windows/Dell.

  Would appreciate help. Found this material to support online and they scanned and said I have eight corrupt & or old drivers, but it is $29,95 to help.

  Thx for any help

  Hello

  driving finder programs can tell you almost anything to earn money from your

  drivers for your computer:

  Make sure you have the latest vista drivers for your computer which you can get your computer manufacturers Web site

  go to their website and look for a driver and software download section

  Enter your model number for the last look drivers vista then download and install

  and for drivers Lexmark contact you Lexmark

  Lexmark wrote the drivers for their products, NOT microsoft

• By Magentic screen saver will not work! Any help out there?

  I am running Windows Vista on a Dell Studio nine
  I've got everything I can think of including related: put in startup, uninstall/reinstall, which makes my choice by default, even turning off security on downloads & installs.  But Vista refuses to launch... (And I do not understand it is maybe not the best choice, but it makes me happy... & I need that now..) Please any help will be appreciated! Thank you!

  Hello MakMeHappy,

  Thank you for using the Microsoft answers Forum

  We want to assure you that Magentic is compatible with Windows Vista. I downloaded this background screen program on my laptop but got errors repeated that he could not install. You are using a version of this software which is known to be compatible with Windows Vista? Is there an another Vista machine that you tried this software and it worked? Are there errors that either Vista or the Magentic software gives which would give us more information as to why it does not work. Have you contacted Magentic support to ask if the software is compatible or if they have a version that will work correctly on Windows Vista?

  Additional information you can provide on this problem would be useful.

  Judd
  Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Magenta misaligned on CP1515n printer

  The magenta color on my CP1515n printer is out of alignment of about 1.5 mm on the right-hand side of the page, but OK on the left.

  I tried the following:

  -Updated to the latest firmware (20130923)

  -Calibration of color (several times)

  -Permanent storage (NVRAM) reset (several times)

  -Mode of cleaning (many times)

  -Restore default values

  I do not have available ToolboxFX because I have a Mac (OS X 10.9.5).) I do not think that the problem is related to the software or driver because it happens when you print the page of diagnosis in the printer menu, which does not imply the computer.

  The printer is out of warranty, but only has 2700 pages printed since new. Levels of toner magenta, cyan and yellow are 42%, 45% and 44%, respectively. I hesitate to try to buy a new toner cartridge, since I can end up having to replace the printer if this does not correct it.

  The user's Guide describes a "Mode of Calibration" option for a full extended calibration. This option does not exist on my Control Panel printer, even if I have the latest firmware, so I couldn't do a normal calibration.

  The problem started suddenly rather than gradually gets worse.

  Any help would be appreciated.

  Hi OWL,

  The printer is perhaps longer under warranty but toners would guarantee.

  When you call in, let them know that you call on an accessory guarantee and question relates to a replacement toner/s. Let them know the toner brands are the battery, they may also have a number of pages, you can print.

  Thank you.

• Levels of HP C7280 ink & put cartridge software/driver?

  Since the day one on my renovated with printer all-in-One extended warranty C7280 cartridge estimated ink level have indicated/felt empty.  At the time and after replacing the printer once again I finally learned by a supervisor of the support phone HP that the factory provided ink cartridges were special and because they were not full, first, estimated ink levels would be would not read.  so... I waited and waited and finally black ink ran out and I replaced it with a new cartridge in date, which worked well but unfortunately its estimate of read ink level empty too.  so... I continued to wait and finally Magenta and Light Magenta down dry and I replaced with cartridges date and still none of the ink level estimates register.

  Although I suspect something wrong with the printer along the cause is it possible I neglected/was unaware of a simple fix to get these read levels now?

  I read the levels of ink directly from the screen on the printer.  No need to use the software Connectivity PC side.  Besides, because of other unresolved problems I uninstalled software applications and uses only the drivers.  This leads to the second question/problem...

  After the support of futile attempts to fix wireless phone another supervisor told me that HP has been in the weeks, releasing an update of the v12 for my printer software.  He had lied because this v12 software released on other printers, but not the C7280 and its nearest summer for one year.  I would like to know if anyone knows what are the intentions of HP?  V12 will be always available for the C7280?

  Unfortunately, with HP I found it much easier to ignore the problems I had and work around them then spend time futile with offshore technical support.  What a WASTE of the industry does discover offshore support at low cost.  They got what they paid for and we had trouble.

  Progress...  There is a simple solution for ink cartridge levels is displayed not correctly - only vacuum for the last 10 months.  However, there was no reason given as to why HP does.  A few days ago, a phone tech took me by making a hard printer factory reset where you unplugged the uinit, then all by pressing the "6" and keys ' # ' plug the power back in.  For the first time that the ink levels read their correct estimates and the self-assessment report showed these values too.

  Unfortunately with the fluid level reading this thread to find out that 3 of the 6 spare ink cartridges I bought 10 months ago and had to start using some 2 months ago where not full.  In fact the yellow cartridge I replaced two days ago to read only 53% full immediately.

  I tried to get HP to compensate me for these three cartridges partially filled and finally spoke to a support engineer in the United States without result.  However she told me that these renovated C7280 printers have been sent with the function of liquid ink level disabled on purpose but did not say why.  She said that the early support should have reset the printer 10 months ago, I agree.

  In the end, Office Max, where I bought the original printer, exchanged the three ink and cartridges for the first time the icons on the screen of the printer ink cartridge all disappeared.  In fact, I thought it was now a new problem, but apparently that's normal when all cartridges are more than 50% or so full - at least that's what said this same technical support engineer.  And for the first time, the self-assessment report has listed all levels of ink to 100%.  Is everything working now?  Time will tell.

  (So restore the printer to Ethernet and using only the printer drivers base v 10 [no printer installed software apps] I don't have to reset the router periodically during print jobs wouldn't last and I feel a printer real reliability back finally.)  It's also I think as my first post here in the forum HPs I checked "resolved."  Also...  I do not work for HP... "and do not like their offshore phone support).

  Message edited by Star 06/08/2009 08:46

• My C8180 does not print the magenta if shades I print directly from my computer

  My C8180 does not print the magenta if shades I print directly from my computer.

  I did a test once my pictures came out with greenish and bluish colors. I saved an image I created and that was a lot of red, pink, purple and magenta on a flash drive. Then I inserted the drive flash directly in the front of the printer and the image printed with all the vibrant colors that it should print.

  I took the same exact image and saved on the hard drive of my computer. Printing through the computer, the colors are muted, streaked and red, pink, magenta sine.

  The problem is not with the printer heads or connectors... it must somehow be attached to the HP program or drivers. Now the question is, how can it be fixed? If I uninstall the HP printing software, if I install it again, won't the same problems with the colors appear again?

  Well, I'll point you to a video on deleting locked files that may be easier to understand than my trying to explain.

  Even if its 2010, the rules still apply.

  http://www.YouTube.com/watch?v=kiwbvwXx-ja

  Brian of Britec explains the process to remove the stubborn locked files with these two programs listed below. It doesn't matter if the locked files were a virus or not. You can stop and replay the video as much as you want, easy peasy.

  Download and install Process Explorer from Microsoft Sysinternals.

  Download and install Malwarebytes Fileassassin

  That should do well.

  Let me know how it turns out.

• Magenta in my Yellow - OfficeJet Pro K8600

  Why are there of Magenta in my yellow and Cyan in my Magenta?

  I turned off all photo "patches" in preferences, set the printer to manage manually in the driver and removed color profiles of colors so that the Adobe software could manage the color.

  It's a strange combination of colors that are intertwined. This occurs when you print outside Adobe? If it prints correctly outside Adobe, then this is a problem with Adobe. If it does not correctly print outside Adobe, then there is a problem with the printer. In this case, the problem should appear on a page of print diagnostics:

  Use the following steps to print a print quality diagnostics page.

• HP color laserjet cp1215 - magenta print align with other colors - Toolbox freezes

  When you print anything that uses the cartrdidge magenta, magenta colour not aligned with the others. I had this problem in the past and have run some utilities from the Toolbox. However, the Toolbox freezes when I open it. I tried to uninstall and reinstall the software and drivers, but the same still. My guess is that the leaves to uninstall a registry record that's why relocation is not successful? Any help would be greatly appreciated!

  This "installation of the device has not completed" or the "Unknown device" Message appears in Windows during Installation of USB document includes a section on the conduct of a complete uninstall.   See this section: Solution 3: uninstall and reinstall the software of HP.

• Photoshop 6.  Suddenly printing on a printer Epson 3800 using photoshop to control the control of colour printing and printer off, my magenta print terribly - washed and less red.  I contacted Epson and had a long conversation--went through a lot of proce

  Suddenly printing on an epson 3800 using photoshop to manage printing and turning off control of the printer, looked terrible magenta color - washed out, less red.  I had a long discussion with people of epson - tried many things - and concluded that the printer was OK.  In fact, allowing the printer control the color mgt produces much better images.  Same print a jpg file printed from the desktop (without using the PS) gave much better results printing through Psalm do any help?     Thanx

  When Photoshop suddenly changes its behavior and you have not installed new software try resetting you preferences.  In fact if you have installed the new software try resetting your Photoshop preferences.   In the past I have had red impressions cast my Epson 4 800, which has been fixed by resetting my preferences.

• Help me! All my text in PDF files are Magenta and it drives me crazy!

  My printer ran out of black ink, so I somehow a way to change the black to 100% magenta text in order to print. Apparently, Adobe has retained this setting, and now every time I open a PDF file, all text is magenta. I do not remember for the life of me how I changed it in the first place, and I can't figure out how to restore it. I went in ' Advanced > Print Production > convert colors "and tried many combinations to try to recover it, but it did not work. I have a feeling that's not what I did in first place (also given that printing does not always work after the change), so I think I did something in all options 'View '. Someone knows how to fix this? It drives me crazy. Thank you!

  Program: Adobe Acrobat Pro version 9.0.0

  Computer: MacBook Pro

  Software: OS X Yosemite 10.10.3

  Try: Acrobat > Preferences > accessibility > replace the colors in the Document

• Help me! I changed the text to 100% Magenta and it drives me crazy!

  My printer ran out of black ink, so I somehow a way to change the black to 100% magenta text in order to print. Apparently, Adobe has retained this setting, and now every time I open a PDF file, all text is magenta. I do not remember for the life of me how I changed it in the first place, and I can't figure out how to restore it. I went in ' Advanced > Print Production > convert colors "and tried many combinations to try to recover it, but it did not work. I have a feeling that's not what I did in first place (also given that printing does not always work after the change), so I think I did something in all options 'View '. Someone knows how to fix this? It drives me crazy. Thank you!

  Program: Adobe Acrobat Pro version 9.0.0

  Computer: MacBook Pro

  Software: OS X Yosemite 10.10.3

  Hello

  Please, try the following steps. I'm sure it would work.

  Launch Acrobat > go to Preferences > select accessibility > select Replace Document colors.

  Let us know how it goes.

  Concerning

  Sukrit diallo

• Lightroom 3.5 Image Raw color Magenta Cast

  My Nikon D7000 raw files all have a magenta cast to them when they are imported into Adobe Lightroom 3.5 and I wasn't turning on multiple exposure. I am running Windows 7 64-bit and have Adobe Photoshop CS4 as well as a trial version of Adobe Lightroom 3.5 (test to see if I want to buy because I can't read my raw files in CS4).

  If I convert my raw files to DNG and then view them using camera raw (CS4), the magenta cast is gone. However, if I find these same with Lighroom DNG files, they have the magenta cast. I tried to re - import my catalog, but each time they all have the same magenta strong cast. Help would be much appreciated as I can't seem to find anyone else having this problem, and otherwise I can't access my raw files.

  The most likely reason is the monitor profile. Recalibrate the screen or if you do not have the necessary hardware/software try switching on the sRGB profile replaces the default monitor profile