Sourcefire Appliance virtual Fail Open?

Similar Questions

• SourceFire - update Virtual Center of defence 6.0.0 Installation failed

  Hello

  I get the following error when applies the 6.0.0 - Sourcefire_3D_Defense_Center_S3_Upgrade - 1005.sh

  Update Installation Failed: [% 1] Fatal error: error running script 000_start/003_check_DC_memory.pl

  Any resolution will appreciate

  Thank you.

  Hello

  This script verifies the memory available to the centre of defence to use, and 6.0.0 requires a minimum of 6 GB of memory, an increase from 5.x versions.

  -Stop of the DC gracefully from the CLI or WebUI

  -In vSphere, right-click on the domain controller, select change settings.

  -Adjust the Configuration to allow a minimum of 6 GB to the device and save the memory settings

  -Turn on the DC back and resume the update.

  Thank you

  Guillaume

• Server ESX to power a machine virtual "cannot open disk scsi0:0. »

  Hi, I get the following error message when trying to turn on a virtual machine, which I copied into the ESXi 4.0 data store u1 server from a vmware workstation. I added to the inventory and tried the power. Here is what I get:

  Cannot open disk scsi0:0: type of disc not supported or not valid

  7. have you forgot to import the disc first? Failed to create virtual

  SCSI device for scsi0:0, ' / vmfs/volumes / 4 b 318298 - 16aee860 - bf19

  -f4ce46aecd31/CentOS-54-32/CentOS-54-32-01.vmdk' Module

  DevicePowerOn switch has failed.

  I created the virtual machine in vmware workstation 7. It is a Centos 5.4 32-bit.

  http://www.VMware.com/download/converter/GetConverter.html

• Problem with virtual pc, open the vhd file

  Earlier, I worked with virtual pc very well on xp.

  later, I deleted some of the .net etc... Associates of the programs of the Control Panel on the local computer
  and I deleted the computer virtual and installed again.
  But now we get an error windows cannot open this file?
  Choose a program from the list etc., opening the vhd image
  can u make clear which program is deleted and what software must be installed

  Please post on the forum PC virtual dedicated listed below.
  http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads

  Thank you

• Supported Cisco ISE Appliance virtual HyperV

  Hello

  ISE Virtual Appliance supports VMWare ESXi hypervisor. Is there a Plan on the roadmap that ISE will rely on HyperV (or, possibly, XEN) in the future, because some customers do not have VMWare, but using only HyperV.

  The same question can be for other virtual devices as vWAAS, vASA, etc.

  Best regards

  It is a question that gets brought up in the Business Unit from time to time.  From now on, there are no plans on official Support from Cisco on any virtual platform other than ESXi from VMWare.

  There were successful on HyperV achievements, but if you have problems, the first thing that should be noted is that you use on a platform not supported.

  Please rate useful messages and mark this question as answered if, in fact, does that answer your question.  Otherwise, feel free to post additional questions.

  Charles Moreton

• Where VMWARE Workstation 11 stores no information about Virtual Machines open

  When you 'open' a virtual machine in VMWARE Workstation 11, then close VMWARE and open again, it remembers what virtual machines have been opened.  Where it does not store this information?

  After a lot of Googling, I found the answer I was looking for.

  The UNK file is located in

  %AppData%\vmware\preferences.ini

  However, the information of the open machine no longer in the UNK file.  It is now located at

  % AppData%\vmware\inventory. VMLS

• Creative Cloud Desktop fails open

  I've seen several questions similar to mine but not exactly like my question. I get no error message. Everything that happens is when I try to open the application of CC icon desktop appears in my sidebar for a fraction of a second and disappears and CC Office fails to load/open. As such, I can't download Lightroom or Photoshop. I'm under 10.10.3 (14D136):

  Model name: MacBook Pro

  Model identifier: MacBookPro10, 2

  Processor name: Intel Core i5

  Processor speed: 2.6 GHz

  Number of processors: 1

  Total number of cores: 2

  (By heart) L2 Cache: 256 KB

  L3 Cache: 3 MB

  Memory: 8 GB

  Boot ROM version: MBP102.0106.B07

  Version of the SCM (System): 2.6f59

  Serial number (System): C02K60CZFGPJ

  Material UUID: 3B94CEA0-4587-5D62-943E-A4A14D90E99E

  Motion sensor sudden:

  Status: enabled

  I got creative Cloud works well on my iMac just do not here. Any ideas? I tried just about all of the options suggested here and still no love.

  Matt

  You mentioned below in the links and I tried with the troubleshooting steps?

  Adobe Creative Cloud closes immediately after trying to start

  Creative Desktop Cloud application does not start

  Creative cloud will not launch in Mac OS 10.10.3

• Cannot run appliance virtual 64-bit on 64-bit capable of vmware server

  Kind regards

  I have VMware Server 2.0, running on a dell d630 latitue 32 - bit XP Pro on a windows-based

  Intel T7100 with EM64T and VT enabled cpu. According to the processor verification tool

  given here,

  my host is able to run 64-bit virtual

  machines.

  However, when I try to start virtual appliance, he repeats:

  Your CPU does not support long mode.

  Use a 32-bit distribution.

  I received the DVD of installation of the unit and tried to create a new virtual machine based on 64-bit RHEL5 (i.e. which, in my view, that the device is from), I had the same problem. I attach a log file of one of these for your convenience.

  Any help will be appreciated. Thanks in advance.

  Well, just by reading your attached journal...

  19:45:38.342 Dec 11: vmx | Msg_Post: WARNING

  19:45:38.342 Dec 11: vmx | \[msg.monitorInit.vmm64.initHost.VTDisabled1\] this host is VT-capable but VT is not enabled.

  19:45:38.342 Dec 11: vmx | \[msg.monitorInit.vmm64.initHost.VTDisabled2\] it is usually due to a BIOS/firmware issue.  Please:

  19:45:38.342 Dec 11: vmx | (1) check that the BIOS/firmware settings enable VT mode.

  19:45:38.342 Dec 11: vmx | 2. turn on the host, if the BIOS/firmware VT settings have been changed at the start.

  19:45:38.342 Dec 11: vmx | (3) turn on the host if you have not done since the installation of VMware Server.

  Just do what is said.  Go into the BIOS of your host settings and make sure that VT mode.  Save and exit, and then turn the computer off (some people even advise to disconnect the power cord).  VT in the BIOS setting is notorious for not making effective changes until that you turn on the computer.

• Firesight appliance virtual system requirments

  Dear,

  I have 2 questions below:

  • I'm looking for the version firesight virtual centre of defence 5.4.X and 6.0 requirements for VM ware
  • As well as ASA in failover mode, that we do not have to configure the becz asa Eve all the configuration is taken from primary school is there any concept even for module of firepower.

  Thank you

  1. the installation guides provide information on the requirements of the VM.

  http://www.Cisco.com/c/en/us/support/Security/Defense-Center/products-in...

  2. we record the two modules of firepower and put them in a device group. Strategies are applied then group so that synchronization is taken in charge by the management center of firepower (new name for the Defense Center / Management Center of the FireSIGHT since version 6.0).

• IPS-4240 fail open

  Hi all

  I have one unit of IPS-4240. I want to know if my sensor or the unit itself fails / stops, is there an option where in my traffic will be passed so that there is no downtime.

  Thank you

  Pratik

  You can configure the sensor when it is inline with inline-bypass 'auto' mode mode so when the unit does not work, it will just pass through traffic without inspection, however, if the sensor is completely shutdown, then no, the traffic will be dropped when in inline mode.

  Here is more information on derivation inline mode:

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/Configuration/Guide/CLI/cli_interfaces.html#wp1047079

  However, if she is in promiscious mode, so you don't have to worry about this because the package is not "inline" and will cause no disruption.

  Hope that helps.

• If an application virtualiced fails, how can I debug it?

  Hi all

  I have virtualiced an application with thin 4.6 App. The entire process was good, but when I run this application in my VDI errors of path (cannot find some files).

  VMware puts some application to debug? I need to know what is going to solve.

  Thank you

  ThinApp troubleshooting tool is Log monitor. Please start the Log Analyzer, and then start the application. In the logfile generated text, look at the "potential error" section near the end of the log for suspicious failures. If your application displays the error message if an error occurs, you can also search for the error message.

• Turn on the computer virtual fails - "could not power on VM: not found".

  Hi guys and girls,

  I'm running a server relatively low with ESXi 4.0.0 running a SBS 2008 Standard VM as well as a couple of XP machines virtual for line inherited from enterprise applications.

  Today, one of the disks in RAID-6 went offline and was replaced, after verifying the integrity of the RAID and the ESXi server restart seems to load normally, and could be connected to via vSphere.

  I noticed that the SBS comments had not begun where was the XP guest.

  I tried to manually start the virtual machine and received the following 95% error message:

  «Could not power on VM: not found.» Unable to power on the virtual machine.

  Failure is classified in Server events:

  "Cannot be lit on localhost in ha-data center." "A general error has occurred:

  Alas, I'm new on ESXi and most of the aid is managed by my hardware vendor which is currently unavailable.

  I tried to remove the virtual machine from the inventory and re-enrollment without success.

  All files appear intact on the data store.

  Any assistance with this would be greatly appreciated.

  See you soon,.

  Tom

  I try to create a new virtual machine and configure it to use the existing hard since your SBS server disks.  Maybe the .vmx has been corrupted?  The file vmware.log in the directory that the virtual machine is could give more information on what is not found.  Use the data store browser to download the file to your w/s.

• "Driver Webcam Fail open. Please restart camera or computer. »

  I installed 7 Ultimate and this driver has stopped working, I contacted Support technique Gateway and was informed that since I did not upgrade directly from gateway which I had to ask the third party provider to help... Any advise on this?

  Thank you!!

  The third-party provider made the webcam. You must try to locate their Web site for Win 7 drivers.

  Messages rating helps other users

  Mark L. Ferguson MS - MVP

• Need help install appliance virtual machine (file unpacking).

  I'm new to VMware devices.  ?:|   I try to install FireScope BSM: BE the device. The directions say to download the image file from tablet to the data store; and unpack once it has been downloaded. It is a tar.gz file. MY question is: how to unzip a file in the data store? ESX Server version 3.5.0 doesn't let me connect to the CLI. Anyone know how I can do this?

  Thank you

  You "might" use the data store browser to upload files to the data store OR you can use a client PCs (google FastSCP) it's free and will allow you to easily upload files to your esx hosts.

  -

• ISE n RAY fail to open

  Good afternoon

  NAC offers parIP admission to fail open on a router.  Y at - it equivalent command to access switches pointing to a RADIUS server?

  Situation:

  Access switches have two RADIUS servers configured, showing a load balancer to Site A (with 6 Ssnp behind) and the second RAY pointing to Site B LB (6 Ssnp behind).  If neither load balancing are available, how could we switch access of relief and apply an ACL giving access only to the Internet for staff?

  Thank you.

  Cath.

  Cath,

  In fact, you can take advantage of the command "action to the authentication event allows id vlan" and empty the users on a virtual local network giving them access while radius servers are inaccessible.

  http://www.Cisco.com/en/us/docs/switches/LAN/catalyst3750x_3560x/software/release/15.0_2_se/configuration/guide/sw8021x.html#wp1194433

  Thank you

  Tarik Admani
  * Please note the useful messages *.