SRM with several paired sites?

Similar Questions

• WLC centralized with several remote Sites

  Hi people,

  I read the documentation of design for wireless devices, and I can't find a definitive answer to the following:

  Is it possible to have a WLC centrally (in a DMZ), who controls several remote sites?  Each site must have the same SSID, however the IP subnet will be different at each site.

  I have attached a base PDF showing what we are trying to achieve.

  Thanks for your help.

  Kris

  Of course, you could put either the AP mode H-REAP so that the data of the customer traffic is enabled locally to the AP or you can use groups of AP.  With groups AP customer traffic be dug to the controller and group AP policy would determine which interface / VLAN, traffic should be poured in.

• Fields on several Internet sites have been changed in another language. The browser is set to English, and this problem does not occur with Chrome.

  Fields on several Internet sites have been changed in another language. The browser is set to English, and this problem does not occur with Chrome. Specifically, a large part of Tumblr and Facebook menu has been changed in another language (Russian, I think). I tried reinstall Firefox, clear the cache and reset firefox to its default state. None of them helped. Any suggestions on how to fix this?

  Hey again,

  Sometimes a problem with Firefox can be a result of malware installed on your computer, you may not be aware of.

  You can try these free programs to search for malicious software that work with your existing anti-virus software:

  • Microsoft safety scanner
  • MalwareBytes' Anti-Malware
  • TDSSKiller - AntiRootkit utility
  • Hitman Pro
  • ESET Online Scanner

  Microsoft Security Essentials is a good permanent antivirus for Windows 7/Vista/XP, if you do not already have one.

  More information can be found in the article troubleshooting Firefox problems caused by malware .

  I hope this helps!

  Curtis

• Is it possible to open several tabs at the same time (with some Web sites on the tabs) by simply using an icon?

  I have several Web site tab groups that each would open by double clicking a single shortcut.

  For example: when I do my banking online, I would like to open a single shortcut, and then that would open all of my banking sites, each in a different tab.

  Do you mean start via a shortcut on the desktop?

  You can add all the URLs on the command line, separated by a space.
  
  If the list is too long, so you must use a firefox.cmd file to start Firefox with all sites.

  • http://KB.mozillazine.org/Command_line_arguments

• Is there a way to open a new window with a site when the House on Firefox setting has several Web sites?

  When you work in Firefox, is there a way to open a new window with a site when the House on Firefox setting has several Web sites?

  Firefox always opens a new window with the home page (s), you must use shift + left click on a link (bookmark) to open a page in a new window or just rip an existing tab by dragging the tab slightly downwards to open the tab in a new window.

• How to set up multiple LIVE IDS prod certificates on Sharepoint 2010 single server runs several Sharepoint Sites with different domain on port 443?

  Hello

  I integrated LIVE ID with Sharepoint 2010 and got the same compliance.

  In sharepoint server 2010, several sharepoint sites are run under port 443 with different domain names.

  I configured 1 LIVE ID certificate for one of our sharepoint sites would like to know can I use the same certificate for other sites too or I need to install other certificates LIVE ID to access other sites.

  How can I get prod LIVE ID certificates are available for free as nexus offers two certificates INT and PROD (x 509 certificate) or do I need to buy.

  If I need to buy where can I buy it go?

  Hi ppdremsadm,
   

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums as it is related to the configuration of Live ID in Sharepoint 2010. It should be better in the Forums of Windows Sharepoint.

  Please ask your question in products and technology SharePoint forums to improve assistance in this regard.

• SA520W VPN from Site to Site with several VLANs

  Hello

  I have a customer here with several VLANS in their places who wants to set up a VPN from Site to site between 2 devices SA520W. Unfortunately I can not find a way to set it up. In the VPN policy, I can choose between everything (which is not what I want, I want only traffict between subnets the routed via VPN), IP address unique, a beach (in a subnet) and a subnet itself - but only one. I don't find a way to configure several subnets in the selection of local traffic and remotely. Adding another IKE policy between the 2 sites does not either (which is good normally).

  Any ideas? Anything I'm doing wrong?

  Thank you for your help.

  Best regards

  Thomas

  I know that if you have an ASA or a router, you can define as VLANS to pass through the tunnel.

  Do not have access to a SA520W to test...

  A recommendation might be to post the question on the SMB community where they answered questions related to this product, just to check what other people did.

  Federico.

• I've updated my Muse app to the latest version of July and since then my Muse forms do not work with several of my web hosting providers. Is this a case of the site not having host is not the latest version of PHP?

  I've updated my Muse app to the latest version of July and since then my Muse forms do not work with several of my web hosting providers. Is this a case of the site not having host is not the latest version of PHP?

  Please consult this document:

  Troubleshooting Muse form used on the servers of third party Widgets

  Thank you

  Sanjit

• SRM with vSphere Enterprise and vSphere Advanced

  Hello

  I saw the FAQ license RS saying that SRM requires no vSphere all be of the same edition and features will be affected by which edition is used.

  Which raises a number of questions in my mind.  For example if my environment is as such:

  • Production site with multiple ESX using Enterprise Plus with Nexus 1000V
  • Recovery site with several ESX using Advanced edition
  • Enough to set up for two sites license SRM and vCenter

  I guess that network should not much question, as I can manually map the port network group on the recovery plan.

  So my questions:

  1. Can I configure manually this ESX made uses SRM for commissioning virtual machines running the recovery plan?
     • I don't have a DRS on the DR site to distribute virtual machines and use all the resources.
  2. What happens when SRM tries to start a virtual machine with more than 4vCPU in the DR site?
     • Advance Edition limited my VMs to 4vCPU

  See you soon,.
  Isabelle

  Your correct indeed neglected the advanced part, DRS is not supported. But another question for you: do you only use the equipment have the Dr site for DR purposes or you also make use of the material for other purposes as for example the test? Is it not that you can always create a business case to buy a license of the company and use the site of recovery for test purposes. In case a disaster occurs and a failover is invoked, you can add stimulus to stop your test virtual machines on the recovering site, before the SRM protected VM. This way make you full use of all the material on the protégé and the recovering site.

  Looking at your question again, it makes me think. If you create a cluster on the recovering site and map this cluster cluster on the protected site. All virtual machines that are protected will be started on the cluster during failover. OK you won't have DRS so resources are not distributed on the hosts, but they run and computers vMotion virtual host to another, you can manually.

  Point which is that you want to map individual VMS to ESX host, making your your design SRM very complex and difficult to maintain. Rather go for mapping clusters and take account of the fact that you have to manually virtual computers vMotion between host computers to create a balanced distribution of resources (or buy some DRS). It makes your life a lot easier.

• Installation with several NetAPP SRA spinning FAS30XX

  We tested SRM successfully between FAS3050 and FAS3070. Now, we are in the second phase and test the scenario where our VM is distributed between several volume and multiple files (all NetApp FAS30XX) server. My question is how can I configure a replication with several spinning to a file server? Because when configure us SRA adapter we provide source IP which is protected site spin, then IP who resumed recovery site go and then we're able to see replicated table. But in the situation where you have several sources how can SRA will be set?

  Thanks for your response

  When you set up picture frames, you can specify more than one table, then you could add essentially several bays that are replicated volumes in a different destination file server and if reporters are operational in a metro cluster or a cluster, you must the failover in case a file server.

  I hope this helps.

• Several pop-up windows "Security Fix" indicating the many problems w/computer & scan to see what they were. returned with several "critical" errors & several "warnings".

  Original title: fix the system

  While the site of the car got several popup windows "Security Fix" indicating several issues w/computer & scan to see what they were.  Do that & came back with several "critical" errors & several "warnings" says had to buy the program to correct.  Then stop computer & when turned on the next morning the only office was trash & start menu is empty with the exception of all programs.  Went to windows defender for all programs & said it was off?  I didn't turn it off & when trying to turn back & says cannot open program, error 0x800106ba.  Help!

  Do you have any antivirus, in addition to Windows Defender?

  System Fix is a fake program aimed at obtaining the payment card information. If you have used your card with it, contact your card provider immediately.

  There are instructions to remove the difficulty here:

  http://www.bleepingcomputer.com/virus-removal/remove-system-fix

  Use only written instructions. Do not download anything from advertising on the Web site.

  This program can damage your computer and the removal instructions may not be completely effective.

• ASA EzVPN with several remote subnets

  Hello world

  I'll have the challenge of EasyVPN installation based on ASA 5520, and ASA 5505 (with the ASA5505 as the vpnclient) with several networks behind the ASA 5505.

  Access by the network directly connected on the 5505 to the central site works very well.

  But the second network segment (which is behind a router on the directly connected network) cannot connect to the central site.

  I guess I need to specify that some sort of acl's to be able to do that.

  BTW we do not use tunneling split, because all traffic moves through the tunnel (no local internet access).

  The layout looks like this

  (--LAN--)-5520---5505-(--LAN1--)-ROUTER-(--LAN2--)-(WAN)-

  LAN1 and LAN connection works great through the EZVPN Tunnel.

  LAN2 connection to the LAN does not work through the Tunnel of EZVPN.

  Here is the configuration used so far (outside the normal SHEEP, groups of objects and stuff ISAKMP crypto):

  Client:

  vpnclient Server 10.x.x.x

  extension-mode network mode vpnclient

  EzVPN vpngroup vpnclient password *.

  vpnclient username user1 password *.

  vpnclient enable

  Crypto ipsec df - bit clear-df outdoors

  Server:

  internal EzVPN group strategy

  Group Policy attributes EzVPN

  allow to NEM

  allow password-storage

  tunnel-group EzVPN type ipsec-ra

  General characteristics of tunnel-group EzVPN

  Group Policy - by default-EzVPN

  IPSec-attributes tunnel-group EzVPN

  pre-shared key *.

  user user1 password *.

  I hope you can help

  Best regards

  Jarle

  Unfortunately, it is not supported on the platform of the SAA. With EasyVPN on the SAA, only the connected networks can be advertised. To accomplish what you want to do, you need to configure a static IPSec tunnel and announce local networks via ACL interesting traffic. You can also use an IOS device that does not have the capabilities of "multiple subnet" with EasyVPN.

  http://www.Cisco.com/en/us/docs/iOS/sec_secure_connectivity/configuration/guide/sec_easy_vpn_rem.html#wp1098057

• Unable to access several Web sites using Windows 7 regardless of browsers

  In recent weeks, I am unable to access several Web sites i.e., microsoft, linkedin, msn, etc., using windows 7. This doesn't work for all browsers.

  I get the following message while trying to launch some Web sites.
  ==============================
  This page cannot be displayed
  • Make sure that the web address http:// is correct
  • Look for the page with your search engine
  • Refresh the page in a few minutes

  Solve connection problems

  =============================

  Whereas, I can access all Web sites by using another laptop that runs Windows XP.

  Enjoy, if someone can help me solve this problem.

  Best regards

  Did you check internet connection on your PC? The question arises even after the wired or wireless internet connection?

• script with several SET options on a single line does not

  I have a script that worked very well on the 4.0.3 version but now in 4.1.0.19, he's not taking my SET options. Simple test case:

  TOGETHER TO CHECK OUT LONG PAGES 350 LINES 500 1000 CUT OFF ECHO FEED

  SELECT RPAD('&val1',100,'Y') FROM DUAL;

  < F5 >

  SP2-0158: unknown SET "check" option

  old: SELECT RPAD('&val1',100,'Y') FROM DUAL

  New: SELECT RPAD('a',100,'Y') FROM DUAL

  RPAD ('A', 100, 'Y')

  --------------------------------------------------------------------------------

  aYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

  YYYYYYYYYYYYYYYYYYYY

  (Size of the default line to 80 characters and show the SQL text for the substitution of the value of the variable)

  It seems to work fine if I use several SET commands

  SET VERIFY OFF

  500 FIXED LINES

  SELECT RPAD('&val1',100,'Y') FROM DUAL;

  RPAD ('B', 100, 'Y')

  ----------------------------------------------------------------------------------------------------

  BYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY

  Is it a bug or a feature in version 4.1?

  I do not use a login.sql (Tools > database > Startup Script is not defined)

  SQL Developer Version 4.1.0.19

  Build a HAND - 19.07

  It is an interesting question.  Of course, SQL * more actually accepts a SET command listing several pairs of variable/value system

  Despite the fact that recent literature does not promise this syntax of management and only mentions the VALUE...

  https://docs.Oracle.com/CD/E11882_01/server.112/e16604/ch_twelve039.htm#i2698538

  .. then by the summary of all the variables SET system...

  https://docs.Oracle.com/CD/E11882_01/server.112/e16604/ch_twelve040.htm

  Check the bug list, I see a fix in 4.1.0 for the case of variable/value pairs 3 (with no error message), but failing to put the last 2 variables correctly.

  By checking your test scenario against 4.1.0 and the last line of the main code, it also works for the first 4 variable/value pairs...

  all check out along lines of 1000 pages 350 500

  then complained to carve out on being the fifth...

  game check long 1000 350 lines of topping on 500 pages

  line 1: "game of topping on ' is obsolete.

  and finally the errors to try to manage any valid system variable after the fourth...

  game check long 1000 pages 350 lines 500 feed

  SP2-0158: unknown SET "check" option

  game check long 1000 pages 350 lines 500 topping on feed off echo off

  SP2-0158: unknown SET "check" option

  Buggy.

• Can I create a Google Map with several points?

  I am building a Web site for a company with several companies, and they want all appear on the map. In the standard Google maps widget, you can add only one address. Is it possible to add multiple addresses without scripting?

  You can always add placements more once you have published the site by editing the source code. Otherwise simply don't use the widget and enter the code clean Google according to custom HTML.

  Mylenium