SSH access to PIX

Similar Questions

• PIX and SSH - access to PIX via SSH

  Need help with PIX and SSH

  Objective: Connect to PIX via SSH from the 10.1.1.50 IP address behind inside the interface on the PIX using local aaa on PIX.

  Current settings:

  hostname pix1

  example.com domain name

  CA generates the key rsa 1024

  example username password abc123 privileges 15

  include authentication AAA ssh inside 10.1.1.50 255.255.255.255 local

  SSH 10.1.1.50 255.255.255.255 inside

  Thanks for any help!

  Try this:

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

• PIX behind Cisco 1841 - need SSH access

  Hello, trying to enable SSH access to PIX for some external host clinets.

  What are the correct Acl I need?

  Exactly correct...

  1 - on the router, you must allow incoming TCP 22 (ssh) to your PIX on the external interface of the router and also allow the flow back of the PIX inside interface of the router.

  2. - to the PIX you must generate rsa keys and save them.

  CA generates the key rsa 1024

  CA save all

  3 - on the pix you will need to allow ssh acccess to you outside of the interface

  SSH outdoors

  Write it down if you find it useful

• PIX telnet/ssh access to the VPN Lan2Lan

  Scenario of several Lan - Lan IPSEC VPN between PIX F/Ws.

  I need to remotely access / these PIX via Telnet/SSH & would prefer to do it through the VPN tunnel.

  NB, I tried telnet/ssh configuration for both inside/outside of my source but can't hit the PIX.

  Because the Tunnel is actually inside-inside I'm trying to connect to the inside interface of the pIX.

  You can do it now in 6.3 code with the command "access management". See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/mr.htm#1137951 for more details.

• Change of SG 200-18 - management - VLAN / telnet/ssh-access?

  Hello

  We have a switch SG200-18 that should be used as a switch of working group in our environment (SW

  Version 1.1.1.8). In collaboration with CLI on big and mid range Cisco gear during the past two decades, I have a hard time to understand what follows on the SG200:

  (o) I want to change the management VLAN by default '1' to the management - VLAN used in our environment. Of course, I created this vlan in SG200-config, however when it comes to assign the management IP and VLAN management interface in the advancement of the corresponding film under "Interface IPv4-> management VLAN" selectable is the default "1". see screenshots (closed)

  So, how to define a management VLAN 1 different?

  (o) how to enable telnet/ssh-access the SG200-18 - I'd be much more comfortable with a CLI environment ;-)

  Thank you very much in advance for your help,.

  -ewald

  Hello Ewald,

  Sx200 series switch does not currently offer a CLI option. Have this feature if the Sx300 and 500 series.

  What about chaning the vlan management, you have two options.

  (1) changes the vlan by default under management VLAN > Default vlan settings. This will change all the ports and the management vlan.

  (2) adds a port as a port untagged in the new VLAN. Once this is done, make sure that something is connected to this port, like a computer. Now you should be able to change the vlan management. (This is done to prevent locking)

• Simple Question SSH Access-List

  I am allowing SSH access for all of our Cisco devices and you want to restrict access to all the following ip addresses: 192.168.200.1 - 192.168.200.50.  I forgot the exact configuration of access list to achieve this.  The subnet is 24 and I don't want the whole subnet - seulement.1-. 50.

  Thank you

  Thomas Reiling

  Hello

  If you use ssh, make sure that you have a domain name, host name and a rsa key is generated.  Assuing you have done this, the command vty ACL and following line will do the trick.  Note that the host 1-50 list is not on a subnet barrier.

  To get it exactly

  access-list 1 remark MANAGEMENT ALLOW
  access-list 1 permit 192.168.200.0 0.0.0.31

  access-list 1 permit 192.168.200.32 0.0.0.15

  access-list 1 permit 192.168.200.48 0.0.0.1

  host access-list 1 192.168.200.50

  access-list 1 refuse any newspaper

  It would be a good idea to put it on a limit, however, so the following would be much simpler and easier to read.

  access-list 1 remark MANAGEMENT ALLOW
  access-list 1 permit 192.168.200.0 0.0.0.63

  access-list 1 refuse any newspaper

  Apply the class of access on the vty lines and authentication, I would put something there too.

  line vty 0 4
  access-class 1
  entry ssh transport

  password Bonneau

  That should do it.

  Good luck!

  Brad

• Remote access to PIX very slow

  Using PuTTY to access PIX 501. The typed commands are slow to display. What is a function of high network activity? The above branch network is not very active. Any suggestion would be appreciated.

  Hello

  You access the pix on its external interface via the Internet. So then Yes, it can be very slow. We manage some firewalls pix remotely via internet, and sometimes it can take ages to record key entries.

  HTH

  Jon

• Java problem when you access 506th PIX

  I get an error message when I try to access my 506th PIX from in the firewall using IE. After the first password, I get the error message "exception: java.security.AccessControlException: access denied (java.utilProperty Permission java.versionread) at the bottom of the page IE.» Any ideas?

  Hi Burns I had the same problem, you need to do is to go to www.java.com and download the java applet and try and access the PIX will work without problem

• Esxi SSH access and locking mode

  If SSH Busybox shell access has been disabled, is there a point to activate the lock mode?

  Thank you in advance.

  While you can have SSH access disabled, vCLI remote access and access PowerCLI is still possible, unless the lock mode is activated.

  If you enable the lock mode, all remote management of the ESXi hosts (whether you use vSphere Client, vCLI/vMA or PowerCLI) must firstly be connected via vSphere server.

  I hope this helps.

• SSH access ESXi 4.1.0 fails

  Hi all

  I have a problem with SSH access on my server ESXi 4.1.0. The problem is that it keeps it all the time.

  Precesely more, I go to the tab "Configuration", "Safety profile", "Properties", "Remote Tech Support (SSH)" and configure the server running (I tried all three options). Then and for a few minutes, I can connect to the server using ssh, both with the root and non-root users. But after a few minutes the ssh server stops.

  I have no idea what's going on. Could you give me a hint to solve this problem?

  Thanls a lot for your help.

  Kind regards

  Agustin

  Hello

  Welcome to the community

  But after a few minutes the ssh server stops.

  Right, this is due to default security setting that stop ssh after a certain time (don't remember what are the exact numbers). If you want to enable SSH permanently you need to go to the screen of the ESX console and enable SSH from there

  http://vmwaremine.com/2010/10/25/how-to-enable-SSH-on-ESXi-4-1/

  See you soon
  Artur
  

  Please, do not forget the points of call of the "useful" or "correct" answers

• SSH access to ASA

  I can not access our ASA 5505 over SSH from outside. I set this through the ASDM to allow SSH (device management > access management > ASDM, HTTPS, Telnet, SSH). I have added a rule that allows the SSH on the external interface 0.0.0.0 0.0.0.0. When I try to ssh with putty, he says 'network connection closed unexpectedly server' when I look at the logs on the ASA, it shows a Built inbound TCP connection on port 22, but then immediately a disassembly TCP connection. It does not show that it is blocked by any rule. Is there something that I am missing about the SSH activation?

  Thank you

  Scott

  Hello

  In addition to the hosts permitted to SSH for the SAA, you must set the RSA keys for the secure connection.

  In the CLI:

  generate encryption rsa key

  For these keys to work, you should have a name of host/domain configured on the SAA so name (unless you configure a dedicated RSA keys).

  So basically, configure a host name, domain name and generate the RSA key pair:

  hostname NAME_OF_ASA

  NAME_OF_DOMAIN domain name

  generate encryption rsa key

  Accept the default of 1024 and it should work.

  Federico.

• SSH access to LWAPP Access Point

  Hello

  I have just a question about the access point (in LWAPP) using SSHv2.

  When can I see the beginning of the AP (in my case a 1242AG) the SSHv2 is enabled, but when I try to connect to the AP by SSH, my SSH connection is cancelled immediately.

  My access point is connected to a switch (i.e: Cisco 3560).

  And another question on this topic... Why that I can ping my LWAPP AP when it is connected to a switch and not when it is connected directly to the WLC (in my case a WLC 2106).

  Many thanks and best wishes,

  Jeff,

  4.1 you can actually enable telnet or ssh by using this command:

  config ap ssh enable

  allow config ap telnet

  But you must assign a user name and password by entering:

  config ap ID password all the

• Allows you to control access VPN PIX

  I have a situation. I want to use Cisco PIX to create 2 VPN tunnels: called "admingroup"(subnet 192.168.10.X) for full access and another called "vendorgroup"(subnet 192.168.11.X) for limited access (only www access to 192.168.1.100). "" "" Admin and the seller will use Cisco for XP vpn clients. But for some reason, the admin and vendor access even. I think I may need to remove the command "sysopt", currently I use admingroup to PIX of remote connection,

  1. can I remove "sysopt" remote control while I vpn in PIX?

  2. why the admin and the seller have equal access?

  Here are the PIX config in a short version:

  permit 192.168.1.0 ip access list nat_acl 255.255.255.0 any

  access-list 101 permit ip 192.168.7.0 255.255.255.0 192.168.10.0 255.255.255.0

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0

  access-list 101 permit ip 192.168.7.0 255.255.255.0 192.168.11.0 255.255.255.0

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.11.0 255.255.255.0

  out_acl list of access allowed tcp 192.168.11.0 255.255.255.0 host 192.168.1.100 eq www

  permit ip 192.168.10.0 access list out_acl 255.255.255.0 any

  IP address outside pppoe setroute

  IP address inside 192.168.7.253 255.255.255.0

  IP verify reverse path to the outside interface

  IP verify reverse path inside interface

  IP local pool adminpool 192.168.10.1 - 192.168.10.7

  IP local pool vendorpool 192.168.11.1 - 192.168.11.7

  Global 1 60.1.1.10 (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 access-list nat_acl 0 0

  Access-group out_acl in interface outside

  Route inside 192.168.1.0 255.255.255.0 192.168.7.254 1

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set RIGHT aes - esp esp-md5-hmac

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 aes encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup admingroup address adminpool pool

  vpngroup dns-server 192.168.1.3 admingroup

  vpngroup admingroup by default-field test.com

  vpngroup admingroup split tunnel 101

  vpngroup idle time 1800 admingroup

  admingroup vpngroup password *.

  vpngroup address vendorpool pool vendorgroup

  vpngroup dns 192.168.1.3 Server vendorgroup

  vpngroup vendorgroup by default-field test.com

  vpngroup split tunnel 101 vendorgroup

  vpngroup idle 1800 vendorgroup-time

  vpngroup password vendorgroup *.

  VPDN group pppoex request dialout pppoe

  A little luck?

• Filter the SSH access to Cisco ASA from the Internet

  Hello

  I have ASA 5520 with 'inside' in local network interface and the interface 'outside' in the face of the internet.

  There are line ssh 192.168.0.0 255.255.0.0 inside for the ASA to LAN access. And deny a rule for incoming traffic on the 'outside' interface.

  I see a lot of refuse the connection from different addresses to 'outside' interface on the ASA in syslog. When I scan external interface with nmap to port tcp/22 internet is marked as closed. Are there opportunities to make filtered?

  Syslog entries are just one indicator of the SAA does its job to block the script kiddies to penetrate your firewall. I see them all the time on Internet-facing firewall when the logging level is set high enough and it's explicit deny on the inbound access list (/ the implicit deny any one who will be outside).

  You can either lower the recording level (4 is recommended), filter this message or pass to a level that is lower than your level on a daily basis, then it disappears as a recurring message that requires no action.

• WRVS4400n (SSH access) port forwarding

  I have a WRVS4400n and a Server CentOS that I need to access SSH from WAN.

  I've created a single port rule to forward to open port 22 and pass to the server (whose address is 192.168.41.3)

  However ssh connect can't, 'ssh user@{external_IP}' command times out after 20 seconds.

  I was wondering why...

  If I connect to my server directly to the modem through the external interface - I have a problem to connect to it. Once, it is behind the router - no luck.

  I even added same rule for UDP, don't know if it's necessary, but it did not really hepl.

  The router is on the version of the firmware 2.0.1.3, on a background version is 2.

  Any suggestions?

  Centre,

  The server does not respond to the front port is because if the traffic is unknown to this subnet it is not sent to the address 41.1 looks. If you can not ping any what other subnet, then the local LAN subnet on the server you will not be able to communicate with a public IP or even a PC via a VPN tunnel, address because the destination IP address is outside the LAN subnet. The reason to ask if the server can ping internet.

  Is it possible to remove the default gateway on the eth0 interface, just in case it is causing problems with the statements of the route on the server.

  What is a linux server?  If yes you can run the command-line - n to see what looks like your routing table?

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security