SSH PIX / ASA

Similar Questions

• User of the restrictions-pix/asa

  PIX / asa, I created the user with the privilege level, how I can restrcit the depending on the level of privilege.

  privilege level example 10 they can't enter config mode.

  advise the pl

  Thank you

  Knockaert

  Hello

  You must enable local command authorization to do so. See this link to enable local and configuration authorization steps.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/mgaccess.html#wp1042039

• How to enable ssh on ASA 5525

  Can I know how to set up remote to access the ASA 5525 via ssh

  I gave the following commands

  SSH 10.60.0.0 255.255.0.0 outside

  SSH 10.60.0.0 255.255.0.0 dmz

  SSH 10.60.0.0 255.255.0.0 inside

  SSH timeout 5

  but I am not able to access the ASA via ssh. I have to add any other command

  you need a public/private key pair:

  ASA (config) # crypto key generate rsa key general module 2048

  a user name:

  ASA (config) # username, password testuser testpass

  and the system needs to know where are your useraccounts:

  ASA (config) # aaa authentication ssh LOCAL console

  Edit: And not leaving SSHv2:

  ASA (config) # ssh version 2

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• PIX - ASA, allow RA VPN clients to access servers at remote sites

  I got L2L tunnels set up for a couple of remote sites (PIX) for several months now. We have a VPN concentrator, which will go EOL soon, so I'm working on moving our existing customers of RA our ASA. I have a problem, allowing RA clients access to a server to one of our remote sites. PIX and ASA (main site) relevant config is shown below. The error I get on the remote PIX when you try a ping on the VPN client is:

  Group = 204.14. *. *, IP = 204.14. *. * cheque card static Crypto Card = outside_map, seq = 40, ACL does not proxy IDs src:172.16.200.0 dst: 172.16.26.0

  The config:

  Hand ASA config

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.1.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.22.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.200.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0

  access extensive list ip 172.16.0.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.1.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.22.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

  access extensive list ip 172.16.200.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0

  card crypto outside_map 60 match address outside_cryptomap_60

  outside_map 60 set crypto map peer 24.97. *. *

  card crypto outside_map 60 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  =========================================

  Remote config PIX

  access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.0.0 255.255.255.0

  access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.1.0 255.255.255.0

  access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.22.0 255.255.255.0

  access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0

  access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.0.0 255.255.255.0

  access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.1.0 255.255.255.0

  access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.22.0 255.255.255.0

  access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.200.0 255.255.255.0

  card crypto outside_map 60 match address outside_cryptomap_60

  peer set card crypto outside_map 60 204.14. *. *

  card crypto outside_map 60 the transform-set ESP-3DES-MD5 value

  outside_map interface card crypto outside

  EDIT: Guess, I might add, remote site is 172.16.26.0/24 VLAN VPN is 172.16.200.0/24...

  What you want to do is 'tunnelall', which is not split tunneling. This will still allow customers to join the main and remote site, but not allow them to access internet... unless you have expressly authorized to make a 'nat (outside)"or something. Your journey on the client will be, Secured route 0.0.0.0 0.0.0.0

  attributes of group policy

  Split-tunnel-policy tunnelall

  Who is your current config, I don't see where the acl of walton is attributed to what to split tunnel?

• PIX, ASA, and RSA SecureID

  Hi all

  I replaced our old Pix 515 for a new ASA 5520.

  On the Pix (running ios 6.x) we have configured the pix to use an RSA SecurID appliance AAA server to authenticate remote VPN clients. To do this, we set up a group AAA using the radius Protocol. Now, for the SAA, I found documentation indicating that I need to create a group AAA that uses the SDI Protocol.

  Now my questions are

  (1) can I still use the RADIUS Protocol on the SAA is to authenticate with RSA SecureID, or what I have to use SDI?

  (2) if I have to use SDI does mean I also have to change the configuration on my RSA I used to authenticate users of the PIX?

  Kind regards

  Screech

  Hi little Duke

  (1) you can still use the RADIUS.

  (2) Yes, you would need to allow auth requests come from ASA

  Roman

• PIX / ASA, including the DNS name of the ACLS

  Hello

  PIX or ASA supported DNS names in ACL or only IPs? Everyone heard talk of plans to support?

  As far as I know (D) DNS is only supported for VPN connections by saving the IPs of the box interface.

  Best regards

  Roberto

  only ip addresses.

• PIX / ASA 7.0

  Is the PIX v7.0 OS the same OS that runs on the ASA? Configurations are portable between the two devices.

  They are essentailly the same thing, even if you can not put a picture of pix on a SAA or vice versa. PIX is Magi begin «pix...» ', images ASA... Well, you can guess.

  There are some differences due to material - an ASA does not have a serial port for failover (to use LAN-based failover), he did not FO/R/UR and interface IDS are different.

  But in terms of NAT, ACL, itineraries, opposed groups etc. is the same thing. You can config port but attention config interface and failover.

• Cannot SSH in ASA after EZVPN configuration and do not specify "split-tunnel-political tunnelspecified.

  Even after the "split-tunnel-policy tunnelspecified" specification with "split-tunnel-network-list value TUNNEL of SPLITTING" and denying all traffic to the public IP address of the ASA, I'm still not able to SSH in the firewall. Everything else seems to work OK, but I have to be able to handle the ASA from the public interface. In fact, I expect little given the mean one sa is the installer for the tunnel, and it would seem that a deny statement would be ignored, but perhaps there is a way around this. Thank you.

  If you want to connect to your home IP through the tunnel, you must specify 'inside access management:

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/a...

  Best regards, Karsten

  Sent by Cisco Support technique iPad App

• allowing permission aaa on pix / asa

  I managed to get authentication on easy enough but now finds it difficult to get permission to work properly. I auth/author enabled for my IOS stuff so any connected Tech will have rights based on what I give them about secure ACS. However, I can't the same thing to work on the code of PIX. I can connect fine with sign aa, but still, he invites me to the enable password. End result is that I want to be able to connect only once (and active). The white papers that can tell me the right way?

  Hello

  What you want to do, it is possible, try following the instructions in the attached PDF file.

  And you want to give access ASDM, then make sure that you leave Assistance user privilege to execute all display orders, i.e. show-(check) permit unmatched arguments.

  Let me know.

  Kind regards

  Prem

• Work around the EXEC Mode when connect in SSH for ASA 8.4 (2)

  Hi all

  I would check with you all, is there anyone able to access the 8.4 (2) Cisco ASA CLI without needs to enter the enable password?

  Currently, it is configured with GANYMEDE for CLI and ASDM access.

  ASDM, we have not had any problems and be able to access and to change directly in own entry GANYMEDE credential.

  However for the CLI, we need to type 'enable' and also the enable password before login.

  Is there anyway that we could ignore the EXEC mode and access to the PRIVILEDGE mode directly?

  Thanks a lot for your help!

  Current config:

  AAA-server xxxx Protocol Ganymede +.

  AAA-server xxxx (management) host xxxx

  Kind regards

  Danny

  Unfortunately, ASA does not support the feature AAA Exec permission yet, so he can't be configured with GANYMEDE or RADIUS to directly access the privileged exec mode. We go through with authentication enable

  Like this:

  ===================

  ASA:username: *.

  ASA:password: *.

  ASA: > activate

  Password: *.

  ===================

  This is because the ASA does not include the cisco-avpair = "" shell: priv-lvl = 15 "attribute."

  The ASA does not support the Exec AAA authorization still features, so it cannot be configured with RADIUS or GANYMEDE.

  The workaround for this problem is to manually the user to activate the mode mode switch.

  It is compatible with IOS (routers/switches).

  Kind regards

  Jatin kone

  -Does the rate of useful messages-

• PIX / ASA - OSPF load balancing

  Hello

  I read the balance a route via OSPF equal cost load the PIX. It will send packages via per package, or is there another method for distibuting the traffic to the break following equal cost?

  Thank you!!

  Lee

  Hello Lawrence,.

  PIX 6.3 now supports the NLB using OSPF only (up to 3 default routes)

  The PIX can receive up to 3 doors by default (all the same metric) 3 different routes of entry, and

  balance the load on a per destination basis. Currently, there is no way the PIX to

  determine which carries a package will be sent to. You cannot currently use static routes

  for load balancing.

  The used hash algorithm is not simple, it is very difficult to determine which

  Route (next hop) a package will be given an IP Source and Destination pair. Basically,.

  the PIX takes the source and destination IPs (two 32-bit numbers) and axe in one

  16-bit unique number. Then the number of 16-bit (0x0000 - 0xFFFF) is divided into thirds.

  The first 1/3 goes to the door of entry 1, the next 1/3 goes to the door of entry 2, and the last 1/3 goes to

  Gateway 3.

  I hope this helps! If Yes, please rate.

  Thank you

• Active/active failover configuration LAN-based PIX / ASA

  Hi all

  I would like to ask, if there is a restriction of length between the two ASA5510 in a LAN failover? Should not be, or I'm wrong?

  Thank you

  Norbert

  Hello

  normal duration of 100 m Ethernet. Or you can use the switches between them. I do not have a direct link.

  Best regards, Celio

• Source of interesting VPN traffic to PIX / ASA

  Is it possible the CLI to interesting to implement traffic source or otherwise test a VPN strategy?

  As far as I KNOW - this is not possible, because you cannot create a tcp/udp/icmp from a source interface in the device.

• Form of CONF. IPSec PIX to ASA

  Hi.I have a small question. I have a PIX configured with Ipsec configuration, but we have now upgraded to an ASA.

  I can just copy paste the configuration of PIX, ASA (all crypto and isakmp orders) or what I have to change some commands to make it work?

  ASA uses the same addresses that PIX used in its configuration.

  ""isakmp key"" command is replaced by the tunnel-group.

  use: -.

  tunnel-group xx.xx.xx.xx type ipsec-l2l

  tunnel-group ipsec-attributes xx.xx.xx.xx

  pre-shared key "isakmp key."

  where xx.xx.xx.xx is the address of the peer.

  Political ISAKMP are replced with

  ISAKMP crypto policy 'number

  authentication

  encryption

  hash

  Group

  life

  I hope this helps.

• ISE 1.3-> ASA ssh and attribute anyconnect

  Hello

  I created a condition made up to match the anyconnect client and allow, if necessary, but the problem is that if the user does not match the anyconnect group and match the ssh group (user group only to ssh the ASA) he get authenticated to anyconnect and go to the default group of tunnel.

  AnyConnect condition: type of device, NAS-PORT-Type = virtual and Cisco - VPN3000:CVPN3000/ASA/PIX7x - Client - Type = client Anyconnect

  SSH status: device type, NAS-PORT-Type = virtual

  Basically, if the user does not match the anyconnect condition it can still vpn through SSH condition.

  Thank you

  Khaled

  There are several ways you can do. Probably the cleanest is to use different strategy games. One for VPN access and one for the administration of the unit.

  But to keep things simple, you can use the same attribute 'Cisco VPN3000'... "in your SSH condition, but instead of '=' you can use 'Different' in this way if the SSH session sees the AnyConnect client, then the condition will not be matched.

  Thank you for evaluating useful messages!