SSL VPN authentication using the ad group

Similar Questions

• SSL VPN authentication using different sequences of identity Sources

  Morning,

  At the moment we have SSL VPN configuration passing security to GBA. This is accomplished by using strong authentication. GBA the

  Sequence identity Sources is WBS then AD.

  We want to implement on the same firewall a few users select proper respect by AD authentication, they will have a group name different tunnel connecting etc.

  GBA im not sure how I would setup two sequences of Sources Identidy therefor using the same Service selection rule. At the moment I have if RAY and IP is XXX then political use of XXX

  We are currently installed ISE so in the not to distant future is ACS can not do this can ISE?
  If it's confusing that I can extend were nesscessary
  Thank you

  S

  Hello

  I don't know how it looked like GBA but on its flexible ISE

  If the rule is simple

  If the RADIUS request is device ASA type formed then check the tunnel-group-name attribute (146) and will benefit from its interventions to the string value choose LOCAL or AD store.

  

  hope this helps

  concerning

• SSL VPN authentication using RADIUS

  I am running version ASA 8.4 (1) and anyconnect version 3.0.1047. My SSL VPN works great, but I encountered a problem with a user. his story did not work, and each time users had this message ""VPN server could not parse request '. "

  I found the problem after getting user information, which means that his user name and password. Had a password '&' as one of the special characters. When we change to something that isn't that it works very well.

  We use the NPS as RADIUS server. but when I run a test within the CLI, it works fine, only when anyconnect requests to authenticate, he fails.

  Someone at - it had the similar problem?

  Thank you

  Marcin,

  This could a re-appearance of:

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsk14036

  Would you be able to test the workaround?

  Marcin

  EDIT

  Looks like this:

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtn75204

• SSL mutual authentication using the Oracle stored procedure

  Hello
  
  DB version:
  Oracle Database 11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit Production
  
  Is possible to perform mutual authentication SSL uses the Oracle stored procedure?
  I read articles and forums saying that it is not a good approach to call the Web service using the Oracle procedure (and I don't know if it's even possible authentication using procs). But I would like to know if it's possible and how.
  
  In other is words there a way to incorporate the client certificate information into a procedure that calls a Web service.
  
  I read the articles to do it in JAVA or .net. But please advice how we can achieve using Oracle procedures.
  
  Thank you.

  934451 wrote:

  Is possible to perform mutual authentication SSL uses the Oracle stored procedure?

  To learn more. SSL what for?

  Oracle PL/SQL only supports client standard TCP sockets. However, interface for HTTP, Oracle PL/SQL also supports HTTPS - which requires the certificates of authentication of the server to be stored in a portfolio of Oracle web and used during the transmission via HTTPS. See the code example {message identifier: = 1925297} for more details.

  I read articles and forums saying that it is not a good approach to call the Web service using the Oracle procedure (and I don't know if it's even possible authentication using procs).

  Forums and articles written by idiots. For idiots.

  And no, I'm not to embellish my response to this pitch that you met. It is false. It is written by ignorant people who don't know ANYTHING about the use of Oracle and PL/SQL. And feel free to forward my response to these idiots. They find me here if they want to argue...

  As an example of how to call a web service, see {message identifier: = 10158148} and {message: id = 10448611}.

• ASA 5520: SSL VPN by using a different IP address that the ASA public IP address

  Hi guys,.

  I'm trying to configure an SSL VPN on a Cisco ASA5520.

  Unfortunately port 443 interface OUTSIDE of the SAA is already used by Microsoft Outlook Web Access and I can not change the configuration of Outlook. This configuration already in place allows me to use the public IP address of the ASA as IP Cisco VPN for the Web page.

  I don't not want to use a different port so to keep life easy for users.

  I have a few available public IPs that I can use so I wanted to use one of them instead of the OUTSIDE of the ASA interface. Any idea how I could do?

  Thank you

  Dario

  Unfortunately you can not use any other public ip address, except the ASA outside IP interface to complete the SSL VPN.

  The only options that you have is to change the Outlook to use another port or the SSL VPN to use a different port.

• ASA by the issue of authentication of the tunnel-group

  Is it possible to do so by the tunnel-group authentication on ASA 8.4.x?

  Here are the scenarios:

  (1) tunnel-group_A performs authentication using the digital certificate (PKI)

  (2) tunnel-group_B performs the authentication using AAA (RSA SecurID token)

  (3) tunnel-group_C performs authentication for LOCAL assistance (AAA user defined locally)

  Tunnel-group_A, B, and C are all using the same physical interface and outside the interface.

  I tested it, but it doesn't work the way I expected.  BTW, I have already disabled "interface authentication ssl certificate outside of port 443"

  Here are the results of the tests:

  If the tunnel group_A is configured with the certificate, then tunnel_group_B connection will fail, but connection tunnel-group_C works very well.

  It seems that tunnel-group_B trying to authenticate with certificate too, if she does not.  BTW, it seems to authenticate to the LOCAL help will still work.

  I understand that you can configure tunnel_group_A to "both" certificate and AAA, but that's not what I want.

  Anyone seen this before?  Is there a way to bypass?

  Thank you

  Joe,

  Yes, I would then use Group-url. And I would create and profile of XML with the specific URL in the list of servers.

  List of servers

  Let me know.

• Authentication IPsec VPN Client using the digital certificate

  Hello

  Please I need some clarification and help to set up my ASA 5540 with IOS 8.3 x for client certificate authentication remote.

  I have my certificate root from the Microsoft CA, but not quite sure if the steps described in the following cisco Web sites are exactly what I need since the firewall seems to generate the certificate to use.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080930f21.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008073b12b.shtml

  My setup is such that the CA will issue certificates to remote clients and the ASA firewall, and remote clients will authenticate and connect with their certificates which the firewall is constantly updating using the Revocation list updated by the certification authority.

  The dhcp pool must be issued by the DC inside network and not on the firewall.

  Are there any examples or best practices to achieve steps will be really appreciated.

  Thank you

  Hi Josh,.

  Let me explain briefly how Auth PKI:

  In a public key infrastructure configuration, devices trust not each other directly, but they have a certification authority, which is the one who issues the certificate. We call this root CA (there may be a more complex configuration WHERE intermediate are involved, but that's another story). So when the root CA issues a certificate, he signs it with its private key. To be able to verify this signature, we should have the CA public key, which is included with the certification authority.

  So for certificate authentication, you must create a trustpoint, that defines the parameters of the root certification authority.

  Then you will authenticate this trustpoint, which basically means that you will get the certificate of the root CA and store locally.

  After that, you sign up to this CA, which means that you will ask for (and get) your own certificate.

  Other users will do the same and have the same root CA Cert, but different personal (identity) certificates.

  So what happens on authentication is that both ends send their certificate to the other, and they will use the public key contained in the root CA to validate the signature of the certificate received from the remote peer. If the signature is correct, this means that the certificate authority root actually issued the certificate, and this remote peer can be trusted (or not)

  Hope this is clear.

• VPN tunnel using the public as IP being the preserve of LAN to LAN encryption

  I have a question who responded to variations throughout the forum, and I feel that my beginner status will be clear. Here is my installation problem... I use a Cisco ASA 5506 and I connect to a provider. I just need the configuration on the local side that they manipulate to their side.

  Internal IP range
  192.168.1.1 255.255.255.0

  Public IP address from ISP

  97.X.X.22

  174.X.X.194

  Config required by the seller.

  All Http Https traffic must come from the 97.X.X.22

  local peer 97.X.X.22

  remote peer 144.X.X.25

  Our local encryption field must be a public IP address: 174.X.X.194/32

  Areas of remote encryption:

  207.X.X.0 255.255.255.0

  144.X.X.90 255.255.255.255
  144.X.X.91 255.255.255.255
  144.X.X.22 255.255.255.255
  144.X.X.25 255.255.255.255

  currently I have the external value 97.X.X.22
  

  I know now that I need to NAT all inside the traffic destined for the remote areas of encryption to 174.X.X.194/32 and then move the valuable traffic to the VPN.

  I use the ASA Version 9.5 (2) can someone help me so that I can avoid interruptions of service, it will be very appreciated. ?

  You will need to modify the ACL Crypto to be the public IP address you use

  outside_cryptomap_1 list extended access permit ip host 174.X.X.194 object-group SP

  --

  Please do not forget to select a correct answer and rate useful posts

• Windows IPSEC and SSL VPN client on the same machine

  Matches (coexistence) installation of IPSEC and SSL vpn clients that are supported on the same computer, windows (XP and Win7)?

  As mentioned by Patricia and Jennifer (5 stars), you can install two clients on the same machine without any problem.

  The tricky part comes when you are trying to connect two clients at the same time, that's when you may encounter unexpected problems.

  However, if your intention is to install both clients and connect them individually and not at the same time, you'll be fine.

  If you have any other questions, please mark this question as answered and note all messages that you have found useful.

  Thank you.

  Portu.

  Post edited by: Javier Portuguez

• Authentication using the table and the existing database

  Very new to APEX here. In authentication methods and was curious to know if it is possible to link the Apex on an existing Oracle database and the table to get information for user name and password. Trying to use the employe_id and last 4 of their social.
  
  Any ideas or things I can read up to get a general idea?

  JosephPortello wrote:
  fac586, thank you. I didn't even know what I had done.

  Yet one thing that happens now after I corrected my incorrect syntax.

  CREATE OR REPLACE FUNCTION EmployeeIDAuth (
  p_username IN VARCHAR2,
  p_password IN VARCHAR2
  )
  RETURN BOOLEAN
  IS
  form l_count NUMBER;
  BEGIN
  SELECT COUNT(*) into l_count from table@db WHERE employee_no=p_username AND bdate=p_password;
  IF l_count > 0 THEN
  RETURN TRUE;
  ELSE
  RETURN FALSE;
  END IF;
  END; 
  

  Now returns an error of:

  Error on line 15: PLS-00103: encountered the symbol "end-of-file" when expects it one of the following values:

  not end up dominant static of final instantiable order pragma
  manufacturer membership card
  1. CREATE OR REPLACE FUNCTION EmployeeIDAuth)
  2 p_username IN VARCHAR2,
  3 p_password IN VARCHAR2

  Any other ideas?

  Remove the false token form.

• using the query - group

  Hi all
  I need to get the sum (sal) and the sum (comm) using the select query...
  I use a group of... but could not get the result...
  For example... If the table is
  ENO ename sal comm deptno job
  1234 2000 1 10 Chief john
  1235 1000 2 20 andrew seller
  1236 2000 3 20 steven Manager
  Clerk robert 1237 600 4 10
  Manager of laura 1238 2000 5 20
  1239 500 6 30 dan seller
  1240 500 7 10 james clerk
  
  I need display all the columns in the select query and the result should be as follows:
  ENO ename sal comm deptno sum (sal) sum (comm) employment
  1234 2000 1 10 6000 9 Chief john
  1235 1000 2 20 1500 8 andrew seller
  1236 2000 3 20 6000 9 steven Manager
  Clerk robert 1237 600 4 10 1100 11
  1238 2000 5 20 6000 9 laura Manager
  1239 500 6 30 1500 8 dan seller
  1240 500 7 10 1100 11 james clerk
  
  I appreciate your help... Thank you!

  Use anaytic SUM:

  SQL> select  empno,
    2          ename,
    3          job,
    4          sal,
    5          comm,
    6          deptno,
    7          sum(sal) over(partition by deptno) sum_sal,
    8          sum(comm) over(partition by deptno) sum_comm
    9    from  emp
   10  /
  
       EMPNO ENAME      JOB              SAL       COMM     DEPTNO    SUM_SAL   SUM_COMM
  ---------- ---------- --------- ---------- ---------- ---------- ---------- ----------
        7782 CLARK      MANAGER         2450                    10       8750
        7839 KING       PRESIDENT       5000                    10       8750
        7934 MILLER     CLERK           1300                    10       8750
        7566 JONES      MANAGER         2975                    20      10875
        7902 FORD       ANALYST         3000                    20      10875
        7876 ADAMS      CLERK           1100                    20      10875
        7369 SMITH      CLERK            800                    20      10875
        7788 SCOTT      ANALYST         3000                    20      10875
        7521 WARD       SALESMAN        1250        500         30       9400       2200
        7844 TURNER     SALESMAN        1500          0         30       9400       2200
        7499 ALLEN      SALESMAN        1600        300         30       9400       2200
  
       EMPNO ENAME      JOB              SAL       COMM     DEPTNO    SUM_SAL   SUM_COMM
  ---------- ---------- --------- ---------- ---------- ---------- ---------- ----------
        7900 JAMES      CLERK            950                    30       9400       2200
        7698 BLAKE      MANAGER         2850                    30       9400       2200
        7654 MARTIN     SALESMAN        1250       1400         30       9400       2200
  
  14 rows selected.
  
  SQL> 
  

  SY.

• Pass through authentication using the client view 4

  When you use the view Client we are invited to connect to the agent connection, then guests again on the virtual Windows machine. I was told that it is because of the legal warning that is displayed before the sign-in Windows appears.

  I removed the warning, and now we're good. is anyone else seeing this and if so what work arounds did you?

  Has been added to the Configuration of the administrator view and it worked.

  Thank you

  Ernie

  A training class for view 4.0.1 told us, that this would happen when you configure LegalCaptionNotice and LegalCaptionText in the registry of your Windows Client or via GPO/policy. (I did not try myself, if)

  To work around the problem (if the warning is required), disable these settings and use 'Message before logon' view - which can be defined in the global settings dialog box - instead.

  André

• VPN client using the certificate self-signed on SAA

  Hello

  I need set up a vpn client that use a certificate automatically generated by the ASA.

  The VPN configuration is easy, especially with the use of the wizard.

  The problem is that I need the procedure to configure the ASA as a CA server and how to send the certificate to the client

  Thank you

  Just to let you know, the ASA can act as a CA server for authentication of cert based for ipsec vpn. It is only possible for sslvpn. So in your case, the client should be the AnyConnect client.

• use the sequence grouping conditional Dynamics

  Hi experts,
  
  I have a simple task (?) - I want number (assign) groups (increase the number of Group) based on a condition.
  
  Here is an example: create groups numbered according to the number of Department (as per the same collection)
  

  create table emp as
  select * from scott.emp;
  
  CREATE SEQUENCE group_no;
  SELECT group_no.NEXTVAL FROM DUAL;
  SELECT group_no.CURRVAL FROM DUAL;
  
  /* automatic grouping - NOT WORKING!!!! */ 
    select ename, deptno, deptno_next, deptno_prev, 
     case when (deptno_next > deptno) then group_no.nextval else 1 end grp 
      from
        (select ename, deptno,
                lead(deptno) over (order by deptno) deptno_next,
                lag(deptno) over (order by deptno) deptno_prev
        from emp
        );

  PROBLEM:
  It seems that the sequence is increased, even when the condition for a new number is not satisfied!
  

  NAME      DEPTNO                 DEPTNO_NEXT            DEPTNO_PREV            GRP                    
  ---------- ---------------------- ---------------------- ---------------------- ---------------------- 
  CLARK      10                     10                                            1                      
  KING       10                     10                     10                     1                      
  MILLER     10                     20                     10                     130                    
  JONES      20                     20                     10                     1                      
  FORD       20                     20                     20                     1                      
  ADAMS      20                     20                     20                     1                      
  SMITH      20                     20                     20                     1                      
  SCOTT      20                     30                     20                     135                   
  WARD       30                     30                     20                     1                      
  TURNER     30                     30                     30                     1                      
  ALLEN      30                     30                     30                     1                      
  JAMES      30                     30                     30                     1                      
  BLAKE      30                     30                     30                     1                      
  MARTIN     30                                            30                     1

  Instead of

  else 1

  I use group_no.currval (same group number, when does not change do not Department). I know, I need to cover the previous number as well, but I did simple, because the problem here seems to be the sequence...
  
  Forward your support :-)
  Duik
  
  Published by: user10939560 on 08.10.2012 07:42
  
  Published by: user10939560 on 08.10.2012 07:44
  
  Published by: user10939560 on 08.10.2012 07:45
  
  Published by: user10939560 on 08.10.2012 07:48
  
  Published by: user10939560 on 08.10.2012 07:49

  "I want number (assign) groups (increase the number of Group) based on a condition."

  But he did exactly want you want. The number of groups is increasing. It is not contiguous, which
  You can not guarantee for sequences of anyway.

  However, if I understand you correctly, it's maybe you need:

        select ename,deptno,
        dense_rank() over (order by deptno) grp
        from emp;
  

  If this isn't the case, please explain in more detail what you are trying to do.

  Published by: Paul Horth on October 8, 2012 08:06

• You want to sort the columns by using the ROLLUP GROUP.

  Want to order the below query using "column of News in descending order and the"Email address"column in ascending order.
  Note: Triage should not bring the total value at the top. It's happening now.
  
  {code}
  SELECT decode (grouping (NVL (customer, "NA")), 1, 'total', NVL (customer, "NA")) 'Email (ID). "
  "Location."
  Sum (News) "News."
  Sum (website) "Web Site",
  OF VW_FX_USERDATA
  GROUP BY ROLLUP (((NVL (Client, "NA")), location, 1, 'total', NVL (customer, "NA")))
  {code}
  
  Please let me know if you need any details.
  
  Published by: Nana Akkivalli on September 23, 2011 16:04

  order by decode(decode(grouping(NVL(EMailAddress, 'NA')),1, 'Totals', NVL(EMailAddress, 'NA')), 'Totals',2,1), 3 desc, 1 asc