statement to reference 0x72ca2f2e to 0x21cc15ff menory memory cannot be read

Similar Questions

• Svchost.exe - Application error. The instruction at "0x7d4caa9b" reference memory at "0x00000010". The memory cannot be: "read"

  Hi, I get the error message after my system boots - svchost.exe - Application error. The instruction at "0x7d4caa9b" reference memory at "0x00000010". The memory could not be "read".

  And then after a few minutes it stops and restarts.
  I'm also not able to use the mouse.
  I need help with this problem
  Thank you and best regards

  Hi GeorgeMotaung,

  ·         Did you do changes on the computer before the show?

  ·         Are you able to boot to the desktop?

  Follow these methods.

  Method 1: Start your computer in last known good configuration.

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After the boot minimum troubleshooting steps, follow section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start and then click Run.

  (b) type msconfig and click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal Startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

• The instruction at 0xfb29a02f referenced memory at 0xbc432cc8 that the memory cannot be read

  What does that mean? "" the instruction at 0xfb29a02f referenced memory at 0xbc432cc8 memory can not be read.. "."  Thank you!!!

  Original title: the PC error message

  Hello

  Welcome to the Microsoft community.

  I understand that you get the error message.

  I will definitely help you with this.

  Please provide the information below.

  1. When did you get this error message?

  2. don't you make changes to the pc before that?

  3. how many time you are facing this problem?

  4. are you this error on a particular program or application?

  Memory could not be written is caused by the faulty RAM memory or a defective hardware.

  I suggest you go through the link below and check if this can help:

  Refer to the suggestion given by Babu V:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-update/the-instruction-at-0x06171610-referenced-memory-at/018f6f84-6598-4a40-8EFA-14ca3049eaf4

  I hope this helps. Please post back with the State of the question and we will be happy to help you further.

• Receive the error message"Sims2.exe - Application error: the instruction at"0x6678e86b"referenced memory at"0x011a3000 ". The memory cannot be 'read - at the opening of the Sims 2

  Original title: I get this weird error when I opened the Sims 2. Can someone help me?

  When I opened the Sims 2, I get this error:
  Application popup: Sims2.exe - Application error: the instruction at "0x6678e86b" referenced memory at "0x011a3000". The memory could not be "read".

  Click OK to terminate the program
  Click on CANCEL to debug the program

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  I have no idea what this means or what to do. Help, please!
  David

  Thanks for the info, it did not work, but uninstalling and reinstalling have. Thank you very much for your help!

• Explorer.exe Application error the instruction at "0x5ad8c78d" referenced memory at "0x082c9c7". The memory can be "read".

  I am running Mirosoft Windows XP Professional Version 2002 Service Pack 2

  Before that, I really want to customize my windows and then I search in google "how to customize windows xp visual styles. After that, I follow the 7 steps how to customize. This is the link I will:

  http://www.WikiHow.com/customize-Windows-XP-visual-styles

  Then, after I followed the steps, it asks me to install this: Neowin patch. When I installed it, it says that my OS is not original, but I just reinstalled the last time.

  Are the cause of the problems of the patch that I installed it in the first place?

  Is it related with my OS?
  How to solve this problem?
   
  URGENT!

  Hello

  Thank you to contact Microsoft Community and we will be happy to help you with your concern.

  According to the description, it looks like you are facing a problem with the Windows XP operating system.

  It would be great if you could answer these questions to help you further.

  1. When you receive this error message, Explorer.exe Application error the instruction at "0x5ad8c78d" referenced memory at "0x082c9c7". The memory can be 'read '?

  2 is the issue limited only to Neowin patch installation?

  There could be a conflict of memory with a driver or due to the bad memory or memory.

  I recommend you to check with the activation status of Windows XP.

  a. Click Start.

  b. click on all programs, then accessories.

  c. click System Tools.

  d. click on activate Windows.

  Windows XP Visual Styles, see the steps in the following Microsoft article.

  http://msdn.Microsoft.com/en-us/library/aa289524 (v = vs. 71) .aspx

  http://msdn.Microsoft.com/en-us/library/5d1acks5.aspx

  Keep us informed on the status of the issue.

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• the statement in memory of reference '0x04d119fa' to '0x13acce40 '. the memory could not be "read".

  When I use the right button of the mouse to extend the context menu,

  as the title, the error message appeared.

  the memory of the statement is always changed

  not only '0x04d119fa', but also '0x046c19fa', '0x100019fa' or other appears randomly.

  Why it is happening?

  I use xp sp3 with the Korean version.

  What you mean that: '.. '. menu popup .extend?

  If Explorer crashes on right-click, looks like you may have a faulty Extension of the Shell Explorer.

  Shell Extensions make up the content of what you see when you right click on something.  If one of them is afflicted, which can cause Explorer to crash:

  When the Windows Explorer (not Internet Explorer) is wrong (especially when right click), begin to suspect third-party add-ons explore extension.

  Those who would be the Explorer extensions that do not belong to Microsoft.  This means that extensions that you have added.  Solution Explorer extensions are generally well and installation of certain applications will install extensions from Explorer solutions for you, give you a choice and sometimes they can be added without your knowledge when you install the new software.

  Solution Explorer extensions are sometimes added as a new right-click option, you see on folders and files (such as the scan of this file, open that file, play this song, etc...).

  If there is something in particular that you do during exploration that you know will be the cause of the problem, which will help focus on the problem and the help that you suddenly know, when you have found and corrected.  If you can get there when you want it, make an adjustment and then there is no message the next time you don't do anything, you do, you have found and corrected.

  First of all you need a way to see what modules explore you have installed now and a way to turn them off (not uninstall them) so you can understand that we are at the origin of the problem.  You can have a lot of installed non-Microsoft extensions you don't know even being given that some installed software installs new without tell you about it.

  Download ShellExView here to see what Explorer extensions you have loaded:

  http://www.NirSoft.NET/utils/shexview.html

  ShellExView does not install anything on your computer, simply of runs and displays.

  After launching ShellExView, under Options, choose "Mark non-Microsoft Extensions" and extensions not Microsoft will be pink, clear, but on some systems which is a difficult color to see, so click on display, choose the columns and move the column Microsoft closer to the top, so you can see on your screen without having to scroll left and right.

  Click on the column header for Microsoft sort display (by clicking on the column of Microsoft) then all the non Microsoft extensions are on top and easy to see.

  Non-Microsoft extensions would be things you have added (non-Microsoft) and are what you should be suspect.

  You can also Google the name of a suspect add-on and see if there is any success on the mistakes of the DEP and what other people have done about it.

  You can Google something like:

  Explorer XP crashing (you must fill in the name of add your suspect on.)

  See what kind of search results hits you get and are looking for solutions or situations that sound like yours.

  I'm not a defender of trial and error, but I can't think of another way to do...

  Right click and disable the non Microsoft extensions one at a time (or maybe in groups of 3-5 at a time), keep a list, so you can enable them again later if you wish.

  The result of the change is immediate and no reboot is necessary.

  Test your right-click fault condition.  If the Explorer starts to behave, you will know that an extension of this group of 3-5 is the culprit in order to start to enable them one by one until the Explorer fails again.

  If you recognize all the extensions that have been added or recently downloaded, start with these first.

  Don't forget - disabling the extension does not uninstall the extension - it is just disabled so you can always turn it on again.  In this way, you can switch back and forth, enabled to be sure, you have the right extension under control.

  Disable them one at a time until your right click on do not generate an error, then restart and test again to make sure the changes 'stick '.  You have disabled the last extension would be suspicious.

  You can also just disable all non-Microsoft extensions, restart and allow them one at a time until you find the one that generates the condition.

  If you have a large number of extensions, you can disable them is small groups, 3-5 at a time instead of 1 at a time until your system starts to behave.  When it does not, you will know that the problem is one of the extensions of this small group and you can enable members of the Group at a time until the problem returns, then the problem is with the last extension that you enabled.

  The hope is that you will find an extension that caused the error, and then you can figure out what on this subject - either uninstall it or see if you can get an update of the author of the extension of their web page.

  I have not your problem, but I can when you toggle extensions, the extension is immediately disabled, so disable an extension does not seem to require a restart, but if you think that you have found the problem, I reboot and repeat the test in any case to be sure the problem disappeared.

  If you post your non-Microsoft extensions list, maybe someone will recognize it as a potential problem.

  If you find the offending extension that's the problem, please let us know what it is that I can add to my list.

• The State of health does not detect bad memory

  Hey everybody,

  I'm running 3.5 update 4 on a Dell 2950. The

  problem I have is that I get a defective DIMM message on the LED of the

  Server, but the parser memory under the health status is green and happy.

  Any ideas why this happens? I noticed on all of my boxes of the host

  You can not expand the section of memory under State of health; You can

  with all other sections. It could be related? Any thoughts?

  Thank you

  Kevin

  What is the code?  I had E2110 MBE (Bit error memory) which do not show in the State of health.  In the past, I used OpenManage on the ESX host.  The company I am now is not installed and I don't know if they will allow it or not.  My problem is that my mistakes were in equipment that located on our site of DR unmanned and we did not know the errors until we are to test!

  Kind regards...

  Jamie

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '.

  Remember, if it isn't one thing, it's your mother...

• Reference DELL e R510 upgraded memoria RAM [MS]

  Buongiorno,

  need di fare one set at level dei miei Server DELL R510.

  Sul sito dell trovo:

  SOLUZIONE 1

  Modulo di memoria sostitutivo certificato Dell 16 GB by some sistemi Dell - 2Rx4 RDIMMS LV for a 1600 MHz ECC

  Number di parte Winery

  SNP20D6FC / 16G

  Number di parte Dell

  A6994465
  a 165 euro

  e

  SOLUZIONE 2

  Modulo di memoria sostitutivo certificato Dell 16 GB by some Dell - 2Rx4 RDIMMS sistemi a LV DDR3 - 1333 MHz (require Westmere-EX (Intel Xeon E7) CPU-PowerEdge R810, R910, M910)

  Number di parte Winery

  SNPMGY5TC / 16G

  Number di parte Dell

  A6996789

  a 190 euro

  Qual'e the migliore Soluzione per me? Come posso verificare is both sound much compatibility?

   

  Supporto Dell

  Buongiorno,

  the memoirs da lei indicates sono perfettamente con compatibility it sistema reported

  OK, my che differenze, sono tra una e l'altra? Quella che costa di piu e piu veloce ha diverse prestazioni? o no no vale la Peña

  Supporto Dell

  , unica cosa, the memoirs currently has bordo 2 x 2 GB vanno estratte prima di installare the nuove.

  perch, so is diverse di memoirs? Ed incpmpatibili tr aloro?

  If a se, posso, having a disposizione della stessa series, installarle server other server knew an altro, Così da a rrivar a 8 GB knew quello?

  Supporto Dell

  
  Speaking saluti

  Manual

  e possibile avere un offerta da referred to dell by the scope ed sommergibili delle memoirs?

• Reference Dell R710 - Configuration of memory

  Hi all

  I'm sure I'm missing something, but I read the two technical papers about memory configuration in the Dell R710.

  I have a server that currently has 48GB stated as follows

  A1 - 4 GB

  A4 - 4 GB

  A2 - 4 GB

  A5 - 4 GB

  A3 - 4 GB

  A6 - 4 GB

  (It then returned on the b-side)

  According to the BIOS it's set to "optimized."

  Now I have sticks of 2x16GB I wanted to install, the only way that I could operate without the whine of BIOS was to install as follows:

  A2 - 16 GB

  A5 - 4 GB

  A8 - 4 GB

  (Duplicated on b-side)

  Giving 72 GB.

  As I read the manual, I should be able to mix the sizes of memory for "optimized" as long I have spend from A1 to A9 and so I have an another 6x4Go sticks left, I want to install.

  My logic is that I can fill with A1 to A9, mixing the 16 GB, however when I try I get the error on the A1/A2/A3 needing to be the same?

  Am I missing something simple? I am unable to make changes in the BIOS, the memory is all of the same type (bought from Dell)

  Rob_991,

  The question that you are running in is due to the R710 need 3 memory channels to match.  Each game nine media is organized in three channels with three supports memory per channel. As shown below, each processor has 3 channels of memory, allowing only a single channel to the need to match, or filled.  So, with only having a couple of 16 GB DIMMs, you are only able to fill a channel on each side. What I would say is the addition of a couple more 16 GB DIMMS fill A1, A2, B1, B2 with them, and then place the 4 GB in A4, A5, A7, A8, as well as B4, B5, B7 and B8. This gives you two channels on each side, as well as 96 GB of memory.

  

  Let me know if this helps answer your question.

• Reference Dell R710 always detected memory guest VM in 95%

  Dear Guys,

  I have a R710 with 2 CPU intel 5506, 8 GB of memory.  I installed several Windows VM inside.  I found that the always detected ESXi host all windows use plus 95% memory and I got the alert or a warning.  When I checked the windows, just using less memory of only 50%.

  I also have an another 2850 and installed the ESXi and there do not have this problem.

  Y at - it suggestions to solve this problem?

  Thank you very much.

  Lewis

  http://communities.VMware.com/thread/211585

• Error message - the memory card cannot be read during the closing of Quickbooks

  I get this when closing QuickBooks (instruction at 0x56461f49 reference to 0x02cd4360 memory. The memory card might not read).

  Hello

  The question you have posted is related to Quick books, I suggest you to send your request in the forums of Intuit for better support. Click on the link below.

  http://support.QuickBooks.Intuit.com/support/articles/SLN40784

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• X 1 carbon memory cannot be recognized

  I recently bought an x 1 carbon with 8 g memory and i7 4660u, win7 system 4 bites, the model is A 20, 7 CTO1WW, I did not choose the screen high resolution, because I think that it is not necessary.

  But the usable momery is 3.08 GB, I am very confused and do not know what the problem is. Is it because the motherboard does not support 8g memory?

  Anyone has the same problem and can tell me why?

  Thank you very much!

  Here is the image of the information system.

  But the usable momery is 3.08 GB, I am very confused and do not know what the problem is. Is it because the motherboard does not support 8g memory?

  Anyone has the same problem and can tell me why?

  Thank you very much!

  I restored the computer to the factory setting, and the problem is solved.

• Wow Error 132 memory cannot be written... and so on

  I'll have wow Error 132 arrive about an hour after the start of the game world warcraft, the game crashes and the error 132. I went on the support site for games and have done everything they said to do to solve the problem, I even updated my drivers and installed a new graphics card and have installed more ram made sure to reset virtual memory but continues to have the error again and become very frustrated and ready to blow this older HP desk top. I also went on HP website to get the drivers right and made sure I had all my top desk needed on their part I tried everything I know to do except replace the computer.

  Hi Noel1969,

  ·         Who is the manufacturer of the graphics card?

  ·         What operating system is installed on the computer?

  This error is because your DDR memory is volatile. This can also occur if the BIOS settings are wrong. The especially voltage can be set to AUTO. It is very important that you set the correct voltage.

  Example: ddr2 6400 setting 1.8 volt.

  Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft has not Microsoft cannot guarantee that these problems can be solved. Change the BIOS at your own risk.

  I suggest that you contact HP to change the BIOS on the computer

  Check the voltage on the computer.

  I suggest that you check the version of DirectX on your computer.

  If you have a Nvidia Geforce, then downgrade to 93.71 driver (they are older, but still work)

  Try the steps suggested by Arygos in the link below: http://forums.worldofwarcraft.com/thread.html?topicId=1272299964&sid=1

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP 11.6 "Stream X 360: for Central memory sd card reader

  The operating system will be able to directly access an sd card in the card as storage drive?  In other words I can store my music on an sd card (in the slot of the card reader) and play directly from card - or will I have to transfer the music to internal memory and then play. ?  The music is non - drm.

  It is possible to play directly from an sd card into the sd card reader slot must rescan whenever I turn on the computer?

  Thanks in advance!

  Bill

  Yes you can do it. Made myself on many Tablet PCs with limited storage. Simply plug in the SD card and use disk management to format the SD card and assign it a drive letter (Mount). You can even take advantage of the load of the main hard disk storage by moving your entire library (documents, music, videos, downloads) on the SD card. I use an SDXC 64 GB (microSD) card in my HP Tablet and it will be same videos pretty well, and music is not a problem at all. To translate see this:

  • To redirect a folder to a new location

• lack of memory-cannot install

  My problem has been resolved for the parameters of the previous owner on desktop XP.  They said to come back and start a new thread for my memory.  Data sheet:

  XP Home Edition

  c. 2002, SP3

  Compaq Presario Intel Inside (R)

  Celeron (R) CPU 2.53 ghz

  248 MB of RAM

  Product # PC130A-ABA

  Model # SR1111NX

  Memory type: DDRPC2700; DDRPC3200

  I just did a system recovery this morning.  I registered the computer for me and then cicked on Internet Explorer.  He brought to the top of the AOL Homepage and cannot connect.  I then went to programs came with this pc for internet registration and fast internet access.  I have Comcast Cable with their modem.

  None had listed.  Have IE8 and Firefox 23 courses.  To get on the internet, I went and changed automatically detects and got online.  Unfortunately, I can not install updates day nor anti-antivirus/Norton Security Suite with Comcast.  I don't have enough memory.  Just the Windows Firewall is enabled.  I guess that until I use this computer I should buy another memory card?

  Someone in the previous thread said to post again and I could get help with maybe get rid of things here using a lot of memory.  Help, please!

  Thank you so much Cheryl!  After I disabled the start points and restarted my computer, it is faster now and this recovery of boot screen appear.  So far, the browsers freeze either.  I'll order this week 512 MB of Crucial memory.  You have visited al ot of help for me!