Static MAC address starting not not by 00:50:56?

Similar Questions

• rejected mac addresses are not placed in vlan comments

  Hi all

  I'm kind of new to the switches and learned a lot by reading the documentation sites. My job is to activate authentication aaa on our Cisco switches, we have a 3750stack, a few 3560 s and some 3550 s. I test on one of the 3560, a WS-C3560G-48PS 12.2 (53) SE1-IP-BASE running. Next week I'll update of firmware for 12.2 (55), but with this version, everything should already work.

  Basically, the only thing I asked to do at the moment is Mac-Auth Bypass configuration. If the Mac address is accepted, RADIUS returns the VLAN, the device should be placed in, for the most part VLAN 4.

  If the radius (freeradius v 2.1.10) server sends a rejection (see below), the port is not set to the vlan comments, because I expected.

  1. 19

     12/21/10 4:23:19.000 PM

     Dec 21 16:23:19 10.1.1.207 37473: 2204830: .Dec 21 16:20:31.950 CET: %AUTHMGR-5-FAIL: Authorization failed for client (f0de.f119.9870) on Interface Gi0/29 AuditSessionID 0A0101CF0000086CF832980B Host=10.1.1.207 SourceType=syslog source=udp:514 client_mac=((f0de.f119.9870)) client_action=FAIL LINEPROTO_LINK=AUTHMGR-5

  2. 20

     12/21/10 4:23:19.000 PM

     Dec 21 16:23:19 10.1.1.207 37472: 2204808: .Dec 21 16:20:31.950 CET: %MAB-5-FAIL: Authentication failed for client (f0de.f119.9870) on Interface Gi0/29 AuditSessionID 0A0101CF0000086CF832980B Host=10.1.1.207   http://olsplunk:8000/en-US/app/search/flashtimeline?auto_pause=true&q=search%20host%3D%2210.1.1.207%22# SourceType=syslog source=udp:514 client_mac=((f0de.f119.9870)) client_action=NOT   http://olsplunk:8000/en-US/app/search/flashtimeline?auto_pause=true&q=search%20host%3D%2210.1.1.207%22# LINEPROTO_LINK=MAB-5

  3. 21

     12/21/10 4:23:18.000 PM

     Dec 21 16:23:18 10.1.1.207 37471: 2204776: .Dec 21 16:20:30.935 CET: %AUTHMGR-5-START: Starting 'mab' for client (f0de.f119.9870) on Interface Gi0/29 AuditSessionID 0A0101CF0000086CF832980B Host=10.1.1.207 SourceType=syslog source=udp:514   http://olsplunk:8000/en-US/app/search/flashtimeline?auto_pause=true&q=search%20host%3D%2210.1.1.207%22# client_mac=(f0de.f119.9870)   http://olsplunk:8000/en-US/app/search/flashtimeline?auto_pause=true&q=search%20host%3D%2210.1.1.207%22# client_action=START LINEPROTO_LINK=AUTHMGR-5

  Can someone tell me where I'm wrong?

  Thank you

  Chris

  Relevant parts of the running-config:
  AAA new-model
  !
  Group AAA dot1x default authentication RADIUS
  Group AAA authorization network default RADIUS
  AAA accounting delay start
  start-stop radius group AAA accounting dot1x default
  start-stop radius group AAA accounting network default
  !
  AAA - the id of the joint session

  !
  control-dot1x system-auth
  !
  interface GigabitEthernet0/29
  235 a description
  switchport mode access
  switchport voice vlan 2
  load-interval 30
  bandwidth share SRR-queue 10 10 60 20
  queue-series 2
  priority queue
  authentication event failure action allow vlan 7
  action of death event authentication server allow vlan 4
  living action of the server reset the authentication event
  multi-domain of host-mode authentication
  Auto control of the port of authentication
  MAB
  MLS qos trust device cisco-phone
  MLS qos trust cos
  Auto qos voip cisco-phone
  spanning tree portfast
  service-policy input AutoQoS-Police-CiscoPhone
  !
  interface Vlan1
  IP 10.1.1.207 255.255.255.0
  !
  interface Vlan2
  IP 10.1.10.207 255.255.255.0
  !
  default IP gateway - 10.1.1.201
  IP classless
  !
  activate the IP sla response alerts
  RADIUS-server host 10.1.1.24 auth-port 1812 acct-port 1813
  RADIUS timeout 10 Server
  Server RADIUS # 7 button wouldn't you know
  RADIUS vsa server send accounting
  RADIUS vsa server send authentication
  !
  end

  Information of VLAN:

  Ports of status for the name of VLAN
  ---- -------------------------------- --------- ------------------------------
  1 default active Gi0/6, Gi0/8, Gi0/14, Gi0/15
  Gi0/18, Gi0/21, Gi0/29, Gi0/30
  Gi0/34, Gi0/36, Gi0/37, Gi0/49
  Gi0/50, Gi0/51
  2 voice active Gi0/1, Gi0/2, Gi0/3, Gi0/4
  Gi0/5, Gi0/6, Gi0/7, Gi0/8
  Gi0/9, Gi0/10, Gi0/11, Gi0/12
  Gi0/13, Gi0/14, Gi0/15, Gi0/16
  Gi0/17, Gi0/18, Gi0/19, Gi0/20
  Gi0/21, Gi0/22, Gi0/23, Gi0/24
  Gi0/25, Gi0/26, Gi0/27, Gi0/28
  Gi0/29, Gi0/30, Gi0/31, Gi0/32
  Gi0/33, Gi0/34, Gi0/35, Gi0/36
  Gi0/37, Gi0/38, Gi0/39, Gi0/40
  Gi0/42, Gi0/43, Gi0/44, Gi0/45
  Gi0/46, Gi0/47, Gi0/49
  3 active video
  4 active DHCP Gi0/1 and Gi0/2, Gi0/3, Gi0/4
  Gi0/5, Gi0/7, Gi0/9, Gi0/10
  Gi0/11, Gi0/12, Gi0/13, Gi0/16
  Gi0/17, Gi0/19, Gi0/20, Gi0/22
  Gi0/23, Gi0/24, Gi0/25, Gi0/26
  Gi0/27, Gi0/28, Gi0/31, Gi0/32
  Gi0/33, Gi0/35, Gi0/38, Gi0/39
  Gi0/40, Gi0/41, Gi0/42, Gi0/43
  Gi0/44, Gi0/45, Gi0/46, Gi0/48
  5 active transfer
  6 active Test ESX
  7 COMMENTS-VLAN active
  999 native active
  1002 fddi-default law/unsup
  default trcrf 1003 act/unsup
  1004 default fddinet law/unsup
  1005 trbrf default law/unsup

  Network type VLAN SAID MTU Parent RingNo BridgeNo Men BrdgMode Trans1 Trans2
  ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
  1 100001 1500 enet - 0 0
  2 enet 100002 1500 - 0 0
  3 100003 1500 enet - 0 0
  4 100004 1500 enet - 0 0
  5 enet 100005 1500 - 0 0
  6 100006 1500 enet - 0 0
  7 100007 1500 enet - 0 0
  999 100999 1500 enet - 0 0
  1002 101002 1500 fddi - 0 0
  1003 trcrf 101003 4472 1005 3276 - srb 0 0
  1004 etnbdf 101004 1500 - ieee - 0 0
  1005 trbrf 101005 4472 - 15 ibm - 0 0

  VLAN AREHops STEHops backup RTC
  ---- ------- ------- ----------
  1003 7 7 off

  VLAN SPAN remote
  ------------------------------------------------------------------------------

  Ports of secondary primary Type
  ------- --------- ----------------- ------------------------------------------

  Hello

  Just to the user the correct names, what you want is a vlan auth failure (that you configured correctly). VLAN comments is for PCs that do not have capacity dot1x (do not respond to dot1x packages) but for the avoidance of the mac, the event of "no-response" will never happen.

  Now that we have explained, your config seems therefore quite ok actually. I'd go with debugs to check what the problem is.

  Debug RADIUS

  debug all EMP

  debugging authentication feature mab all
  debugging authentication feature mda all

  Nicolas

  ===

  Remember responses of the rate that you find useful

• Static IP address does not work

  Hi everyone, small problem.

  I put a static IP address (http://www.youtube.com/watch?v=rHQzHCQhHHgup, this is how I did it) and now my WiFi does not work. I tried most of the things at this point, and its getting on my nerves. When I go to my modem config (192.168.0.1) I see the device listed with the IP address has changed, but when I go to any Web site other then my modem config, internet will not work. It also shows that if I ha no WiFi in my task bar thing. I have a static IP address on my Tablet very well and want to do the same with my laptop win8.
  Any suggestions?

  Hello

  1 have. what measures you taken to set the static IP address?

  2. don't you get any message/error code when you try to access the internet?

  3. What is the brand and model of the computer network adapter?

  I imagine the inconvenience that you are experiencing.

  This problem may occur if you have correctly configured the static IP address.

  Here are the steps to manually configure the IP address in Windows 8

  a. go to the search box, type ncpa.cpl , and click the icon that appears in the result.
  b. a network connection window opens. In the network connection window, right click on 'connect to the Local network' and select 'properties '.
  c. a Properties window opens. In this window, select "Internet Protocol version 4", and then click on "Properties".
  (d) another new window will be opened. In this window, click on 'use following IP address ". Your IP address, then click 'OK' to save the setting.
  e. in this step click on 'Close' in the Ethernet Properties window. All your network settings will be changed.
  f. now you can see your address IP changed. That open to a command invites as administrator and type ipconfig and press Enter.
  g. your network adapter settings have been changed.

  If you are still having problems connecting to the internet, so I would ask you to reset TCP/IP and check if it works.

  Follow these steps:

  one) starts at the desktop view.

  (b) open the command prompt, right-click in the corner when the start window appears, select command prompt (admin).

  (c) at the command prompt, copy and paste (or type) the following command and then press ENTER:
  netsh int ip reset c:\resetlog.txt

  Note: If you do not specify a path of the directory for the log file, use the following command:
  netsh int ip reset resetlog.txt

  (d) restart the computer.

  See also:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• E1200 cloning MAC address but not the PC

  My ISP requires MAC authentication on the router for internet access. They provide the router and register for this router to their access list.

  I'm not very happy with the router, that they provided, so I intend to buy an E1200 and clone the MAC address of my current router. But when I checked the router interface, of cloning mac page has a button saying 'Clone MAC from my PC'. And in the FAQ of E1200 page it says that the router can automatically capture the PC's MAC address. Which is not what I want to do.

  I want to manually enter the MAC address of my older router in this router to be cloned. Is this possible?

  Yes it is possible. Once you enable Clone Mac address of the router, click DO NOT Clone My PC Mac. Enter the mac address manually, then click on save settings. In this way the router will save the mac address you want to enter.

• Get the iPad or Android device MAC address does not work (works in AIR Desktop)

  I try to get the MAC address of the device to the user in Adobe AIR. This is the code that I use.

  public function getDeviceMac (): String {}

  Return NetworkInfo.networkInfo.findInterfaces () [0].hardwareAddress.toString ();

  }

  That works well in the PC (or during the test in the PC with ADL Mobile).

  but in the iPad 2, or in a device Android (Acer Iconia A500) I get an error

  on the property There is not. I guess it is not implemented in mobile

  versions of AIR. It would be nice if it was applied in future versions.

  There is no work around for this?

  I'm looking for just a way to uniquely identify a device, is there

  a unique identifier that I can get the AIR by programming

  (maybe the UDID?), if it is not possible to obtain the MAC?

  Thanks for your help!

  Hello

  You will need to iterate through all available interfaces and find the hardwareAddress.

  NetworkInfo.networkInfo.findInterfaces () [1].hardwareAddress.toString ();

  In addition, for Android, you will also need to specify the permissions ACCESS_NETWORK_STATE and ACCESS_WIFI_STATE in the following application descriptor.

  ]]>

  -Pahup

• assignment range static mac addresses

  Anyone know or knows where I can find what the mac address range is responsible for functions static mac end user for virtual machines?  There is a specific, cited in the 4.x documentation Beach, but the docs 5.x just say do not walk on the beaches of use reserved for vCenter Server, host network adapters physical, virtual cards, but says not what is Beach, reserved or allowed is, so I don't know what to avoid.  I opened a support ticket and asked the same question and I was told there is no specific void range defined for static assignment, and I have to look in my environment to see what was automatically generated for what could not be attributed.  Of course, this does not solve the potential problem of an address that I choose to be automatically generated by vcenter for a future new virtual machine.

  Also, does anyone know what virtual machine operations can cause the mac to change address?  I'm trying to determine whether it is necessary to assign a static address to a virtual machine that has a license associated with it, so I need to know what would be the probability of this change.  Support could not answer this question.

  Thanks to all in advance.

  Have you checked the http://pubs.vmware.com/vsphere-55/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-55-networking-guide.pdf 148 pages

  Documentation - once the MAC address is generated, it does not change unless the virtual machine MAC address conflicts

  with that of another virtual machine saved. The MAC address is stored in the virtual machine configuration file.

• Script to set the static Mac address

  I have an Infrastructure virtual with about 200 vm with several vNIC and automatic Mac address. I need to assign static Mac for all NICs for and want to perform this operation with a powershell script and a csv input file. I have the entry csv file that looks like this: Vm, portgroup Mac Vm1 00:11:22:33 Vm1, pg1, pg2, 00:11:22:44 Vm2, pg1, 00:11:44:44 (I know the Mac above are not valid) can anyone help with the powershell code to automate the static configuration of mac?  Thanks in advance

  Hello, ITS.

  You should be able to use the following to achieve:

  ## import the info from the CSV$colNICInfo = Import-Csv c:\vmNICInfo.csv$colNICInfo | %{    $oSingleNICInfo = $_    ## get the VM, get its NetworkAdapters and for the one whose NetworkName matches that from the CSV, set its MAC address    Get-VM $oSingleNICInfo.VMName | Get-NetworkAdapter | ?{$_.NetworkName -eq $oSingleNICInfo.NetwkName} | Set-NetworkAdapter -MacAddress $oSingleNICInfo.MACAddr -Confirm:$false -WhatIf} ## end foreach-object
  

  A few things to note:

  • I left the '-WhatIf "parameter on the Set-NetworkAdapter portion, so that you can run this first (perhaps with a small sample of game in the CSV file) to check that things look like they will work.  Remove this parameter to set the MAC addresses
  • The code provides that the CSV of this format:
    MACAddr VMName, NetwkName,
    someVM, VLAN128, 00:50:56:00:00:0F
  • The cmdlet Set-NetworkAdapter requires the new MAC address in the range 00:50:56:00:00:00 - 00:50:56:3F:FF:FF.  It's not the range likely to use, VMware only a subset.  Seems to be a limitation of the cmdlet (probably intentional).

  Message edited by mattboren: added a note about removing "-WhatIf" to actually set the MAC addresses of the network adapters

• Create the virtual computer with a static MAC address

  Hi all

  Im trying to create a virtual machine with PowerCLi but im failing to connect New - VM with an addapter network?

  I know that you can create new network addapter with:

  New-card network -MacAddress 00:50:56:bb:00:13 -Type e1000 -NetworkName ' Vlan 6 Virtual Machine '

  But this will create just a network card on the server im related to the use

  to connect-viserver

  New-VM

  -Name VMSTORE23 -$vmhost $esxhost -data store $datastore DiskMB - 20000 MemoryMB - 2019 -NumCpu 2

  I think that the cdmlet that I need to use is OScustomizationSpec - but like I said im strugling to connect?

  Someone at - it ideas.

  Thanks in advance for your help.

  Eddie

  You're almost there, the MAC address must be specified as a string, enclose it.

  New machine virtual- - name VMSTORE23 - $vmhost $esxhost - $datastore - DiskMB 20000 - MemoryMB 2048 Datastore - NumCpu 2 - NetworkName "Vlan 6 Machine virtual network | Get-NetworkAdapter | Set-NetworkAdapter -Type Vmxnet3 -MacAddress "00:50:56:bb:00:2 b" - confirm: $false

  I added the - confirm the setting, as it will not request the change.

• MAC address purging do not ISE MAC Authentication Bypass database

  I'm having a problem where my client's MAC addresses are not be purged automatically from the ISE.  It is a simple amp construction, where users are offered a cover page and must hit 'accept' to access the internet.  When the user does this, their MAC address is added to LSE, and then they can visit his profile.

  I need clients who will be presented to the splash page at least once a day.  Because the MAC address is added when they hit accept, they never get again presented start page, unless I have manually delete the MAC of Administration > identities > endpoints.

  I put the frequency of bleeding under Administration > identity mgmt > settings to 1 day and under settings Portal comments for "purge endpoints of this identity group every day 1", but the MAC stay in this group even after several days.

  I have also set the reauthentication is very short (30 min) in the thinking authorization profiles that might help, but the customer never receives the page again after hitting accept because the MAC is still listed in the endpoint group.  The only way to get the start page to reappear for customers is to manually remove the ISE MAC...

  Is there something else I am missing to make this feature work?

  Attached are a few screenshots of the parameters.

  Thank you!

  It looks like a bug, seems to me that you do it right, I got it working for a client in point 1.3 of the ISE, just with a much longer period before the purge (3 months). ISE what version are you on?

• Wireless devices shows the MAC address for 1 device that does not have an IP address

  I am tracking down each device connected to my router nighthawk and I identified everyone except this. There is a device of Wirelsss appears when I connect to the router that does NOT have an IP address but it has a MAC address. An interesting point is that the router device itself has a number of MAC that is not anywhere in the list of devices. Any ideas what this could be? I have an Extneder range wireless attached Nighthawk also but I already idenfified his IP address and Mac address.

  How a device could have a mac address, but not IP address?

  Why the address of the router device do not show in the list of anywhere?

  Try to turn off the Extender and see if that will fill again.

• How to find the MAC address for photosmart c510 - printer, not zineb

  HP Photosmart c510 all-in-One

  Windows 7 SP1

  Printer bought 2 weeks ago.

  Printer wireless light is not on, not even flashing

  I use MAC address filtering on my home wireless router.  No problem adding the Zeen, I found that it is easy MAC.  Of course for the printer, it says "Printer not available" on the display of zineb, just below the zitoun MAC address.

  So I need to add the MAC address of the printer to my router.  I know that I can turn off filtering by MAC address and I hope that the printer connects, and then I can print the printer network settings, get the MAC, and then again turn on the filter and add the printer Mac

  Is this the ONLY way I can get the MAC address of the printer?  I'd rather not have to do that whole process, but will if I have to.

  I also wonder why the printer wireless light is not even blinking as he is looking for a network.

  Can anyone help?

  Print a network Test Wireless in the network menu on the front of the printer. It will contain the MAC address. Note that MAC filtering is not in that ensure that used MAC addresses are sent in the clear, and it is easy to impersonate a MAC address on a computer.

• A5120 switch - 48G EI didn't poster not MAC addresses connected to the port card.

  I tried to get connected mac address is displayed under political network for a switch HP A5120. model JE069A. My other switches show mac addresses, but not this model. All are in the same policy in foglight. I don't know if it related software, or something in the configuration of the switch. Any suggestion would be appreciated.

  I think that you may have about the product of network Foglight (SGR) management system.

  If so, your best bet is to post your question in the Forum of Discussion of NMS rather than the Foglight Management System forum.

  Kind regards

  Brian Wheeldon

• Bind the MAC to the static IP address with WRT54GL router

  Hello

  We use the WRT54GL Wireless router to connect 4 pc to internet. One of these pc requires a static IP address, because the router can do only reliable port-forwarding for IP static (I would ssh it and use it as a web server). I was told that this router has this ability, but for the life of me I can't find.

  Could someone tell me how to proceed? I am running the latest firmware (v4.30.11).

  Thanks in advance for your reply,

  Michiel

  DD - WRT is fairly stable and well maintained. There are a lot of people using it and you get excellent support, if you don't mind not very technical responses to opportunities. Generally, the flashing of the firmware does not support the warranty. But that wouldn't be a problem if you have had a bad flash. And even for a bad flash you often have options to recover the router.

  For the static IP address on the computer, change the settings of network to the ethernet interface. I do not know Gentoo you should have administration GUI for this somewhere.

  You can use the following values:

  IP (as mentioned earlier) for instance 192.168.1.10
  subnet mask 255.255.255.0
  address of the gateway 192.168.1.1
  192.168.1.1 DNS server

  As long as the static IP addresses do not conflict with the DHCP server address pool create there will be problems running some static IP computers in the same local network with DHCP clients.

• MAC address static configuration

  Hello

  Is it possible to set a static MAC address for a virtual machine using VMware Player? I tried to follow these instructions for VMware Workstation:

  Maintenance and modification of the MAC address for a Virtual Machine

  but when I start the computer virtual, the changes that I made to the crushed vmx file, and I'm back to the original MAC address.

  Thank you

  James

  Check out this article and let me know: VMware KB: change MAC address of a hosted virtual machine

• Satellite L750D - MAC address change by itself

  Satellite L750D/L755D 18mths old.
  Restarted this morning after the weekend and cable NIC MAC address has chnaged.

  Started in windows and could see a different value to Friday (as we control access through MAC address and was blocked).
  Started in normal Linux (Ubuntu 12.04) and a different MAC address again.

  NIC seems to work fine with whatever he chooses - but how MAC address can be change by itself?

  > NIC seems to work fine with whatever he chooses - but how MAC address can be change by itself?

  The physical MAC address is not editable, but there are a few ways to spoof the mac address
  For example, using Windows XP, the MAC address can be changed in the properties of the Ethernet adapter. On the Advanced tab, under "MAC address", "Locally administered address", "Ethernet address" or "network address". The name of this option depends on the Lan driver that is installed on your laptop. And important note; not all drivers are supported changing the MAC address of this way.

  In addition the system registry key:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} contains some parameters of the network interface and the option called NetworkAddress will serve to set the MAC address.

  There are also tools that could spoof the address MAC for example, SMAC MAC Address Changer.
  Finally and above all some routers provide an option to change the MAC address.