Steam tables

Similar Questions

• How to configure a lab overlooking tubular heat exchanger to get data

  HiI

  In our undergraduate engineering chemical labboratory we want to configure our DAq with lab VIEW tubular heat exchanger to get information on the temperature (flow cold fluid warms up), (the steam pressure on the side of the hull of the heat exchanger) and flow (water warms up).

  Can anyone suggest thermocouples, pressure transducers, and flow meters to stay between the heat exchanger and the acquisition of data?

  P.S. the heat exchanger is already equipped with a pressure gauge, thermometers and a rotameter, but we do not know how to connect these devices to data acquisition

  Looks like you have enough information to choose appropriate sensors, you just need to do the research. I start looking into Omega catalogue, or give them a call - they are generally useful. I can't take the time to spec parts for you - it would be a lot of time on another project. Most pressure sensors put a signal 4-20mA or 0 - 5V, that is which you can read through an analog input on a data acquisition; measure a 4-20mA signal requires a resistance to convert voltage. Most NI DAQ boards can read a thermocouple on an analog input, but make sure that your hardware is supported reading thermocouples. For an accurate reading, use a device that has the compensation of cold welding integrated - for example, the block connection SCB-68 - and for more accurate measurements, get a Board specifically designed to measure the temperature.

  For measurement of the flow, a standard, simple solution is an orifice plate. You put a transducer for differential pressure across it, seek the appropriate equations and use them to calculate the flow rate given the density of the fluid (which you will be able to calculate from the pressure and the temperature, since the steam tables are widely available). Other differential pressure devices are available as well - at a previous job, we used a double cone of McCrometer. If you call them, they spec for you - but get an approximate cost first to make sure it's in your budget.

• How to capture value of table column-level changes using oracle 11g steamed

  How to capture the value of the column of table changes using oracle 11g steamed. (similar to the audit).
  Oracle made the steam would be the best way to do the same.
  Please notify. Please give me a code example.

  user4485803 wrote:
  How to capture the value of the column of table changes using oracle 11g steamed. (similar to the audit).
  Oracle made the steam would be the best way to do the same.
  Please notify. Please give me a code example.

  Look at the change data Capture

• Can I place tables in an anchored frame?

  I want to place two adjacent tables in one of my framemaker documents. Should I use a framework anchored to this? If so, how is it possible to place two tables in an anchored frame? Is there another way to do this? Help, please!

  Thank you!

  A table can be placed in a block of text.

  An anchored frame can contain blocks of text.

  A graphic frame can also contain text blocks.

  If you need tables to be able to move, i.e. If your steam content exchange, then placing two blocks of text in an anchored frame would be the way to go.

  If you need the paintings on a specific page and never move, you can then use a graphic image that contains two blocks of text.

• That the face is lit mode bedside table may be shortened? He remains too bright for too long

  That the face is lit mode bedside table may be shortened? He remains too bright for too long.

  Hello

  No, it is not currently possible to customize the duration for which the screen remains lit mode bedside table.

  If you want to send feedback or feature requests to Apple, you can do so here:

  https://www.Apple.com/feedback/watch.html

• Table of contents for several sheet file...?

  It is possible to:

  1. Create a Table of contents listing all sheets in a file?
  2. Have these hyperlink worksheet titles to the sheets themselves?

  I build what will eventually be a fairly large file (read: 75 + leaves). Rather than scrolling all the leaves one by one by one manually to locate the correct table, it would be useful to have a table of contents or an Index that lists the in order... Ideally, allowing the connection of hypertext link to the leaves they reference. (I swear that this was part of a way-back-when number...)

  Instead, is it possible to auto-trier worksheets in alphabetical order? He would not give me the project view as a table of contents or an Index of 35,000 feet, but at least it would be a little easier to find what it takes.

  Looking forward to sharing the wisdom...

  HI stephanie,.

  The numbers 2 (' 09) and 3 support not the hyperlinks to locations within the current document. Both take in charge of hyperlinks that open a Web page in your default browser or which will open and send a new e-mail message.

  Command-F can be your friend here.

  Place an array of single cell on each sheet (or use a cell on the existing table). Enter a short text string that identifies the table or sheet. Each string must be unique in the document.

  To access the card containing one of the following strings:

  Press Control + F to open the Find dialog.

  Enough chain to identify the worksheet type.

  Number will draw this roadmap forward as soon as it can determine which table contains the cell containing this string.

  Tested with four sheets containing:

  able, baker, charlie and delta

  With this limit together (and any other tables in the document - quite an artificial situation!), type c or d was enough to bring me to sheet 3 or 4, sheets 1 and 2 required two letters (ab or ba) to identify the good sheet and bring it forward.

  

  

  With a document containing several tables (and more leaves), create (and remembering) a separate channel for each becomes more complicated.

  You can place a second copy of each in a table of Index or table of contents on a separate sheet. From the index table,

  Copy the entry for the table/worksheet you want to go.

  Open the dialog to find (command-V)

  Paste the entry in the search box. (What it will find and highlight the entry that you have copied to the index table)

  Click on the > button on the dialog to find the occurrence FOLLOWING this string (on your target table.

  Kind regards

  Barry

• Automate the cells of the filter to another table based on two columns

  Hello

  What I'm trying to do is: filter multiple cells to a new table. In this example, I want that all students (column 'lidnr', 'city', then the first 7 columns) with 1 teacher in the 'First' column to be copied into the table 'teacher 1'. The same goes for students per 1 teacher in the column "second". I know it can be done with the help of the filter and the copy paste, but I would like to know if this can be automated, because there are many more tables in my actual document.

  

  

  I've been using maybe to think the search formula but he can't give me more than one result, the result must be unique.

  Thank you very much for your help.

  Kind regards

  Kim

  Hi Kim,

  The usual way to do this is to add an index for each table for which column the data is to be copied.

  Here is an example of preliminary. Improvements after return from the light of day.

  

  Triangles of error on the last row of T1 are thanks to the formula out of data to search for. Easily fixed.

  Order of the names is different from your example, which is grouped by day numbers. Build lists in the desired order, rethinking the index calculations.

  Course index calculations use the formula below, entered in Table 1::L2 and thre to the rest of the blue full cells filled.

  L2: = IF (OR (RIGHT($H2,1) = RIGHT (L$ 1.1) RIGHT($J2,1) = RIGHT (L$ 1.1)), MAX(L$1:L1) + 1"," ")

  Data recovery on the Table T1 is well done by the following formula, entered in A2 and down and B2 and filled and down-filled.

  A2: = INDEX (array 1::A, CORRESPONDENCE (LINE (−1, 1 Table): $L, 0))

  B2: = INDEX (array 1::B, CORRESPONDENCE (LINE (−1, 1 Table): $L, 0))

  More tomorrow (actually, later today).

• Need help with table

  I have a spreadsheet that has about 40 different sheets with each of them being a person that lists information about each of them and if they participated in a given event.

  Is there a way to create a table that spans all of the leaves and can show participation based on the event? A bit like a portal into a database. My struggle is to be able to drag the formula down to automatic change sheets. I don't want to have to individually type an if then formula with offset to connect the number for each field.

  You mention a portal on a database. I think you're on the right track. It is easier to gather information in a table that it is from the dozens of tables. Why not keep your data in a database table and 'extract' information for a person of this table.

  If you could give more details one you are trying to do someone here will be able to give more specific suggestions.

  SG

• How to change the default alignment of text in the cells in a table on the demand for numbers?

  I'm new to Mac. I own a MacBook pro MF839HN/A and currently using the 3.6.2 release NUMBERS (2577). I want to know if I can change the default alignment of text in the cell in a table of NUMBERS application? Also, when I select all the cells in a table to change their alignment, I can only change the horizontal alignment of the text and not the vertical alignment. To change the vertical alignment of the text in a cell, I have to select them individually. Help me with two questions.

  The only way I know is to create a table that is set up as you like, then save the empty document as a template customized by using the menu item "file > save as template:

  

• iBooks author - TOC shows the empty entries for table - how to stop this?

  Hello

  I spent hours trying to find an answer to this.

  My book has a few tables - nothing wrong with that.  I have a front cap of the table - that's what I want in the table of contents.

  iBooks author shows instead, empty entries whenever he comes across a table, that is hopeless.

  

  I just want the topic as indicated above - 2.1.  I don't want 2.2 which is the table.

  Does anyone have an idea how to do this, please?

  If this isn't the case, iBooks author is desperate for any book that contains the tables.

  See you soon,.

  Mike

  Hello

  I found an article from Apple which may help to answer your question and I pasted the link below. I think that you will have to 'say' iBA this is or is not part of the Table of contents (TOC) and's done it with the Inspector tool, Document tab, section TOC. Look down at the bottom of this window to the sign and arrow down to allow the addition of other document settings in the table of contents, or remove some.

  I hope that this help =)

  iBooks author: Customize the table of contents

  

• Match color of series for a table and a chart?

  I created a table with 4 sets of data.  Then, I created a graphic line with this information.  I noticed that when I select the line graph the data in the table becomes highlighted with a lighter version of colors used in the chart.  Each series Gets a corresponding really nice color to match the graph.  As soon as you select any where else these colors disappear.

  Is there a way to automatically match line chart series color color of the card?  If this isn't the case, I see this as the colors that appear in the table so that I can put in manually?

  Select the series by clicking on the graph, then any "point":

• Table of contents don't link to pages in a doc Pages

  Info entry:

  1. a .pages document
  2. blank template
  3. presentation of two columns

  The problem:

  Table of contents generated refuses to do interactive links to the corresponding pages. Styles is ok (so that's why I was able to compose the TOC).

  What is the problem and how to operate?

  4.2 pages (iWork ' 09)

  The document itself (a link to download, editable).

  https://drive.Google.com/file/d/0Bwsy7q2Qc3TCOElPVG02TWFqV3c/view?USP=sharing

  I forgot to mention that my document consists of many sections. While my other document that has its main contents in a cot, a great section working very well in this regard, for example, I am able to go to any title by clicking an appropriate fake (the pointer is active as opposed to the doc above).

  Much appreciate any input on this.

  Thank you

  I.S.

• Paging in the poorly aligned table of contents

  As you can see in the screenshot below, the pagination is right-aligned, sometimes in the table of contents, and sometimes it seems all wrong. What should I do to fix this?

  

  Hello joachim,.

  Pages 5.6.2 on OS X El Capitan 10.11.5

  Menu > view > show rules.

  You can select (click) each level (Style) of the Table of contents and view the parameters of the rule.

  

  

  With the second level selected, look in Control Panel of Format > text > tabs

  

  Please call with questions.

  Kind regards

  Ian.

• stop the email addresses in the table in the spreadsheet to launch mail

  I am compiling of data in a worksheet Numbers and many cells in the table into them from the e-mail addresses.

  Whenever I tap on the cell that contains an e-mail address, he jumps to my Mail application and launches a new mail with the email address. It's so irritating cos I have to type on any address in the table and I DON'T WANT my Mail App to launch. How can I stop this madness? Help, please!

  Hi helix.

  

  Drag the column wide (or Panel Format > table > column)

  

  Click on the white space to the right of the link to select this cell without activating the link

  

  Now, edit

  

  Tested on a MacBook Pro with numbers under Mac OS X El Capitan 10.11.5 3.6.2

  Kind regards

  Ian.

• How to adjust the tabs in TextEdit tables

  I have a basic table with two columns in a file of TextEdit in which a simple text using tabs to align nicely:

  

  As you can see, the text becomes crab down right where numbers lie.

  Normally, I just select the entire block of text and then drag the indicators of the tab on the ruler to spread out the stops to provide enough additional space. Imagine my surprise when I discovered that do not have controls on the tab on the squat within the table rule!

  I'm sure I could do this work several major versions ago, but I forgot the thing. I think there may have been a dark control for a leader of the separate tab pop up inside the table.

  Can someone help me? Thank you.

  Never mind--on more than experimentation, I found myself in the solution.  You will need to set the tab stops on the left only, column that will affect both columns.  I was trying to set the tab stops on the right column, which does absolutely nothing (failure of WYSIWYG).