Stop during updates, now it does not start!

Similar Questions

• Computer hung over the Windows, restarted, update now it does not start even with the installation CD, Get blue screen with the stop message.

  Hi, I installed a Windows update when my computer froze, so I turned it off and back on, now I can't even boot to the installtion disk supplied with the computer. When I hit F8 reapeatedly and select one of the available options, the computer contiually restarts and will not even go into safe mode. I tried hitting ctrl-alt-del, which brings me just for the system configuration menu. I even tried a software that is supposed to start any computer with any problem, and I get the same results I get with the installation CD. (Blue screen with error message: STOP 0x0000c1F5 (0x00000000, four times).) I can't do anything with it, can you help me!

  Windows Update Forum:

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly understand exactly what happened when you tried this update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• HP 15-af131dx: software AMD updated now, it does not start

  I got a new laptop so, crossed and stuff windows update then in cataclay AMD control center or whatever, he know a new version is ready so I installed it and when he asked to restart I clicked Yes and now it gets just hooked up with the screen with the small HP logo in the middle and little indirect points. I don't know what to do?

  I know its probably not the fault of HPs, but Microsoft was of no use and I never got my drivers to work. AMD said it was a problem of windwos, finally that I got tired of the op just to pass a reworked Windows device and known under the name of windows 10 7 and it works fine with no problem. Maybe one day they will be number 10 and how to make it run right.

• Open my laptop, now it does not start

  Hi everyone, the first time poster.

  I opened my laptop (touchsmart tm2 1070ca) to attempt to clean the keyboard and now it does not start at the top.  all the LEDs light up, but the caps lock LED flashes.  The fans and hard drive look about 2 seconds before silence, and about 10 seconds later, the laptop beeps loud and then stops.

  When I opened upward, the touchpad is detached from the motherboard. I finally get it reconnected, but it turned out to be very difficult.

  I tried the Bios recovery suggested on the support site, but it had no effect.

  any help would be massively appreciated.  no no not my laptop will really make my life difficult.

  I know this is an old thread but since there was no solution, I felt should display what has worked for me, in case someone else has this problem.

  This morning my computer refuses to start and the caps lock blinked. I've read elsewhere that a user of a model different from simply removed HP sound CD ROM and re-inserted. My laptop is a HP tm2 Tablet PC, so it doesn't have a removable CD ROM, but I was wondering if another device had become "loose". First, I removed the dongle USB for my mouse and battery and then restarted. That did not help so I forced a stop down (press the power switch.) Then, I opened the background panels and reinstall the RAM (actually happened two sticks to make sure) and removed and re-inserted the HD then restarted again. I don't know which of these factors did the trick, but it worked.

  Hope someone finds this useful info.

  G.

• Adding 2nd NIC (pci express gigabit) to DC7700p. Now, it does not start.

  Adding 2nd NIC (pci express gigabit) to DC7700p.  Now, it does not start. Can not pass boot F9 or F10 Setup Menu. Or the boot or installation menu is accessible.  Any ideas?

  Hello:

  The PCIe slot on a dc7700 usable only for a PCIe video card. If you want or need to add an additional NETWORK card, you need to add a PCI NIC.

  Paul

• What can I do to correct premierepro CS5.5 after win 7 to win 10 update? It does not start.

  What can I do to correct premierepro CS5.5 after win 7 to win 10 update? It does not start.

  An idea that MAY work to install or run some programs in Windows old 10

  -read what to do in https://forums.adobe.com/thread/1945740

• HP ENVY 15-uo11dx: did a reset and now it does not start

  I did a reset system where I chose to erase all mt files and apps. Now, he ends up with the spinning thing and does not start. I can get info from the bios with the F2 key and updated and then restored to the bios and nothing.

  Well I thought about it myself by pressing the F11 key several times and following the menu there. Thanks to this HP online

• It seems that there are updates but AppStore does not start

  It seems there are updated but does not start AppStore. Someone at - it an idea how to solve this problem. My iMac restart does not solve the problem.

  I am running OS X El Capitan 10.11.4

  THX in advance

  Select the text below, go to the Safari menu > Services > reveal in Finder.

  ~/Library/preferences/com. Apple.AppStore.plist

  Remove the "com.apple.appstore.plist" file and then restart your Mac and try again.

• Satellite Pro 4220 - update the BIOS does not start

  Hello!

  Please, someone tell me what is the problem with the update to v1.60 SP4220 BIOS? It does not start even do it according to instructions.

  I did the following:
  1 download/have unzipped the package v1.60 since the BIOS page on a non-bootable floppy disk empty
  2. put the floppy in the computer
  3. turn on the device with the F12 key

  With a floppy, I got the "non-system disk" error and another with a "EMBRL" error message missing. What is it, I'm not familiar with that one?

  Best regards

  Pete v.

  Hello

  Can I ask why you want to update the BIOS?
  You have problems?
  If the laptop works well the update of the BIOS is not necessary! My laptop is about 6 years old and I have no day BIOS!

  However, I think that you didn't use the right update procedure.
  Please check this document before starting the BIOS update:
  http://support.toshiba-tro.de/KB0/TSB4A00SD000BR01.htm

• I put norton on my pc and now it does not start

  I put norton on my pc and when I start the pc, the sign of the window appears but the pc does not start then. I think I have more than a secruity of the internet on the pc. I was told to start in safe mode and remove all of the programs, I have, but still have the same problem. Can anyone help please.

  Since then, you can start safe mode, run a restore of the system to a point just before the installation of Norton if possible.

• I downloaded an update and restarted my computer, received the blue screen of death shortly after the computer restarts. Now it does not start

  I don't know when the downloaded update, the computer has been restarted on September 10, 2010 to install updates. Shortlyl once the computer is restarted, I got the blue screen of death.  with the details of error like:

  Stop 0 x 000000050 (0 x 000000000000000, 0xFFFFF88001DCAE4, 0xFFFFF8A00B490027, 0 x 00000000000002) do not know if the number of zeros is exactly right in one of those, but it's super frustrating.

  I tried to restart my computer in repair as recommended (get blue screen of death), I tried to reboot normally, loop just restart procedures asking if I want to restart in repair mode.  I tried SafeMode (BSOD), I tried to restart with last working restart (restart loops), I tried to choose the "Computer repair" BSOD I tried a diagnosis and all past.

  Help!

  Thank you.

  So yes actually hear nothing helped me.  Seems that, given that the computer is not stopped correctly and my hard drive was not recognized there starting the cycle upward or give me the BSOD.  Put it in my Ubuntu CD spare which I've had since my last PC hard drive became corrupt and force back across my hard drive.  After doing this, I was able to do a boot repair, who led for the BSOD.  Not sure how that actually fixed, lost about 10 hours of my day.  So I guess I can chalk up to Microsoft and a reminder on why I should buy Mac for now on... an update shouldn't really cause such problems.

  I get that not everyone has the same PC, so it is difficult to tell if an update is bad, but he should not do this and if an update is the cause of a certain segment of consumers who are updating must be taken down for everyone, or at least the users with the configuration that is known to have problems with an update.

  Problem is solved, had to go back to a previous version of good boot where I have not install updates again.  Now, I'm trying to understand who was was bad, so I can leave my computer knows to ignore.

  Nice day.

  Just in case someone needs to know how to use Ubuntu to back up files on their PC that does not load windows, please see the link below:

  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer/

• Update of Firefox does not, so I re-installed. Now firefox does not start at all?

  Yes firefox, I started one morning, and I saw that it has been updated. After waiting, the notification saying "firefox is updated" crashed so I had to shut it down. When I started firefox again, he stated that the update failed, but less than a second after that notification skipped upward, it crashed also. He continued doing this, so I followed some instructions on the internet, re-installed firefox (without deleting the data of a personal nature), but now, firefox won't start at all!

  Now what?

  Unfortunately, I never submitted before incident reports, so the folder does not exist in my computer

  But the good news is that I tried running in windows safe mode, and it worked, then after returning to normal windows, it did not work. After waiting a while, now it works again, so I guess this can be considered resolved now

• CS5 and GTX285 worked, run Adobe updated, now it does not work... why?

  So I bought a Gigabyte GTX285, installed in my 3DBOXX, and everything was great (still had CS4). Yesterday, I bought and downloaded Master CS5 Collection. Everything went very well - I opened the first, ran some stuff has been really impressed with the speed increases and loved it. However, I noticed that my support for a RED film was not yet where it should have been (has not supported the new color RED, like CS4 space... a problem that had told me would be fixed in CS5 since it had supported native RED and does not need obsolete plugins red) made on a hunch, I ran the update from Adobe and discovered that my download was 5.0. He ran the update to 5.0.2 (or what is later) and after the update was done, I started first and immediately got a warning message saying that I didn't have a card active CUDA CUDA effects would not be available, and that I need to install the latest drivers for my video card. Well, I went on the Gigabyte site, downloaded the latest drivers for my card, installed and restarted. Still get the same message when I load up to the first.

  For what it's worth, I already had the latest video card drivers installed during my first install of CS5 and download and the update I did after spending the first message was simply a replacement of the drivers with the same.

  Anyone have any suggestions on how to solve this problem and get the most out of my system? I convinced my bosses to buy CS5 and the GTX285 specifically for improving the performance, so if I can't do this job, they won't be happy!

  Thank you!

  What driver version are you running? See if the NVIDIA site has newer drivers available then Gigabyte offers.

• Re: Satellite P100 - after update BIOS it does not start optical drive

  I have updated the BIOS to 4.70 in my P100 PSPAAE. After restarting, I expect about 10 minutes, but nothing has happened, after that the screen of the BIOS, the screen went black. I turned off the laptop only.

  I chose the option "start windows normally". Since (I assume) the laptop does not drive. Any, I have to start from there. Everything else works fine.

  It is because of the update of the BIOS, or something else could cause this problem? Any idea or help appreciated!

  Hello

  The optical drive is recognized from the BIOS?
  You can read the disc in Windows?

  Maybe you should load the default settings in the BIOS and try another bootable disk.

• Update the system: does not start after upgrading to Windows Vista SP1.

  
  

  I had the same problem. Called Lenovo, the response was:

  N ' - what is Vista come with SP1? No! Then, it is not a supported configuration. You're on your own! Bye: Pei

  Well, there is a feature called "Automatic updates" and Microsoft forces you to use - and you're foolish to not use it! In any case, I hope the support to the Denmark, named Thomas, and his bosses to get a better attitude towards customer.

  My question was simple. He was missing a Windows Service called "system update". It is implemented in "C:\Program Lenovo Update\SUService.exe.

  I had register service menually. There is a tool in the .net framework called InstallUtil.exe. The SUService.exe is implemented in .net, the InstallUtil can help.

  Start a command prompt by right-clicking and choosing "run as Administrator".

  Run:

  C:\Windows\Microsoft.NET\Framework\v2.0.50727\InstallUtil.exe "C:\Program Update\SUService.exe Lenovo."

  Modification of traces according to needs. If InstallUtil.exe is missing, it could be part of the .net SDK - do some research on Google.

  Go to services (in the contral Panel - administrative tools) and start the newly created service "system update". System update now worked for me.