structure of the event recorded does not change value

Similar Questions

• Button value change records in the structure of the event, but does not change appeaance?

  Hello world

  A quick question... I hope someone can answer...

  I have a code that uses a PS button within a structure of event to trigger a signal of AO... My code is below. The code works fine and the OD goes off when you press the button E-Stim... But when pushed the button does not change with reliability the appearance (i.e. of the gray 'off' red 'on' color)... Sometimes color changes; no other time not... If I remove the structure of the event and the survey button in the appearance changes as expected.

  What is going on? I would like the button to change the colors on the user interface to indicate that it works... Should I programmatically control the color?

  Kind regards

  Jack

  

  I guess that when query you the button you have some delay in your loop? Locking means that the button will change its value when you press it, then switch back to the original value once the value of the control has been used by the code. When you ask, this means that until he reaches the next iteration of the loop, but in the case where the structure that will happen immediately.

  The default setting for the buttons to modify its behavior as in most of the application would be latch releasing. You then raise the event when the button of the mouse over the control. This also allows "drag" control if you push down on the subject, given that you do not release control in this case.

• SSRS 2008 SP4 - header or footer of the report contains the dynamic image does not change

  Hello

  Our version of Reporting SERVICES to current production is 2008 (not R2). And we have the problem that the header or footer of the report contains the dynamic image does not change accordingly.

  According to this hotfix, the problem has been resolved in the last SP R2 and we tested, it works.

  https://support.Microsoft.com/en-us/KB/2563216

  So we applied the latest SP to SQL Server 2008, however, the problem persists.

  However, we do not expect to upgrade the SQL Server 2008 to 2008 R2 for the moment.

  Guys have faced the same problem before and has an idea how to solve this problem on SSRS 2008 or any workaround?

  Thank you

  Kind regards

  Dan

  Hi Dan,.

  For assistance on questions related to SQL Server 2008 and SSRS 2008 SP4, ask your questions here:

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

  https://social.msdn.Microsoft.com/forums/en-us/home?category=SQLServer

  Hope the information is useful.

• The application name does not change in 2.0 WebWorks

  Hello

  I changed the name of the application in the config.xml file in the www folder. But when I reinstall the application again, the application name does not change. Removal and installation of new but certainly not it's always the same thing with the default name which is «WebWorks app» What is the problem? I couldn't change it.

  Thank you.

  Hello

  It is a known issue with version beta. The name and the icon is changed in the file of the bar, but persists on the device. If you have to deploy the same file on another device appears the correct name.

  The solution is to change the code of the widget as well.

  This will be fixed in the Gold release.

• Urgent - the sound recorder does NOT work after getting the window system 7 (64-bit)

  I have a problem with the sound recorder. After that I got the system with Windows 7 (64-bit), the sound recorder does not work. It's very urgent because I need to procticing my English pronunciation and the test day is coming.

  Please would you give me help? I really appreciate!

  Thank you very much.

  Eleanor

  A prompt by right clicking and select "Run as Administrator"
  and then at the command prompt, type: chkdsk /f r, then press the Enter key.

  If you are asked to plan the volumn to check the next time that the system restarts,
  Enter: y

  If you know the manufacturing of your hard drive you can also download their diagnostic software.

  Another use: SpeedFan has an online health analysis function
  (SMART tab) for hard drives. It will show how your disks
  compared with other discs of the same brand and model.
  http://www.almico.com/SpeedFan.php

  ========================================================================

  Run the SFC/scannow command. This will check and repair if necessary all of the critical Windows system files.

  Click on start / all programs/accessories then
  Right-click on the command prompt option and select "Run as Administrator".
  (or "Safe Mode" open a command prompt)
  At the command prompt, enter: SFC/scannow

  Windows 7 - order SCANNOW SFC - System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  How to analyze the entries in log file generating the program Checker (SFC.exe) resources of Microsoft Windows in Windows Vista:
  http://support.Microsoft.com/kb/928228

  J W Stuart: http://www.pagestart.com

• Structure of the event - controlled motor not variable

  I have a state machine that includes certain structures of the event. These event structures are used to control stepper motors using an Arduino Mega microcontroller. I'm using labview in 2012.

  The entrance to one of the events is the variable "pour the entry. I want to use it to control the motor speed and direction.

  If I control the motor as shown in the attached image Working.jpg, then the motor functions correctly. If I fix the motor to the steps variable # then the engine moves at the speed set in the right direction depending on whether the entry "pour" is positive or negative.

  However, I want to control the speed of the engine, not the number of steps, with the variable "pay Input". I checked that the values read by the indicator image INPUT_VALUE works do not are of the same order as the specified values, working, by using the "Set Speed". When I connect the value of the entry to the spindle speed of the motors of the Arduino (not_working.jpg) icon, the engine is running, apparently indefinitely at maximum speed. I don't understand why there is a difference in motor behavior between the value provided by these two methods at the entrance to the speed of the motor. I am confused by the present and don't know where to go from here.

  The structure of the event somehow behaves differently when taking a value from outside the structure to this data inside? or y at - it something to do with the opening of the structure on its first loop?

  I have also attached my vi together, even though she may not be the easiest to follow and requires an arduino Mega to run.

  Carlr wrote:

  I have a state machine that includes certain structures of the event. These event structures are used to control stepper motors using an Arduino Mega microcontroller. I'm using labview in 2012.

  The entrance to one of the events is the variable "pour the entry. I want to use it to control the motor speed and direction.

  If I control the motor as shown in the attached image Working.jpg, then the motor functions correctly. If I fix the motor to the steps variable # then the engine moves at the speed set in the right direction depending on whether the entry "pour" is positive or negative.

  However, I want to control the speed of the engine, not the number of steps, with the variable "pay Input". I checked that the values read by the indicator image INPUT_VALUE works do not are of the same order as the specified values, working, by using the "Set Speed". When I connect the value of the entry to the spindle speed of the motors of the Arduino (not_working.jpg) icon, the engine is running, apparently indefinitely at maximum speed. I don't understand why there is a difference in motor behavior between the value provided by these two methods at the entrance to the speed of the motor. I am confused by the present and don't know where to go from here.

  The structure of the event somehow behaves differently when taking a value from outside the structure to this data inside? or y at - it something to do with the opening of the structure on its first loop?

  I have also attached my vi together, even though she may not be the easiest to follow and requires an arduino Mega to run.

  You have a very inappropriate design of "state machine" - even if you do not have same event in more than one of your structures of the event (in addition to time-out), looks that get some of your treatment to go forward until you get something very specific (and in which none of your other user events are being processed).

  I strongly suggest that first set you design of State machine - perhaps follow producer/consumer Design Pattern (events) rather than having everything in a loop, the way you have.  If you keep everything in a loop, you should consider redesign so that you at least allow events to deal with rather than stay in a loop for an indefinite period!

  In any case, in the case where work, you send variable "Set Speed (steps per second)" for engines step by step write vi.  But otherwise, you're feeding 'Entry for' value - are they the same? And to let you know, you send only command "write" step by step when the input value to be paid.

  It's a big mess!  For starters, look at the attached picture, get rid of your structure of the event that has "for the entry" and replace it with what I showed in the picture. (In fact, all your event structures can / must be replaced with a similar logic.) Does not need the event structure in all this, you're just more complicated it must be!

  -DP

  

• Global VI on the low level does not change from front panel indicator

  I attributed to a global variable (CMM_SN_Global 3.vi) to a value in a Subvi two levels down from the façade. When I run the VI of Panel before a flag set by the overall does not change even if the global variable is assigned the correct value until later in the program. Shouldn't be an indicator on the Panel before the value assigned to the global as soon as the world is assigned a value. Or is it not true?

  Thank you.

  Chuck M.

  Hi Chuck,

  If you asked for examples:

  

  What we have here:

  -the select node with these 3 Boolean constants is really absurd (aka RubeGoldberg) the output is always TRUE!

  -l' 'position' indicator belongs outside the case statement, any write on this indicator ("unnecessary local"!)

  -Why is there an additional wait inside the case? Do you really need that as you expect in the while loop?

  -It is not recommended to compare floats for equality - as you do here with the structure of your case when wire you a DBL to the input switch. Why not convert the data itself in full to be on the safe side?

  Then you say: "my plan is to have ten independent loops like the top.

  This is the reason for using subvis. You can have as many loops as you want, but only need to code once the algorithm ("duplicate code").

  More comments on why I recommend some "realignment"?

• Satellite A300-17N - the CPU multiplier does not change under load

  Hello

  I have Toshiba Satellite A300-17N. Yesterday, I noticed that my CPU does not change its multiplier under load.
  I have used programs like premium 95 and Orthos CPU load and programs such as CPU - Z and Everest.

  The multiplier blocked on 6 and do not change its value.
  Under load the multiplier should change its value to 13, but it didn't happen.

  In this case my CPU works on 798 MHz (133 x 6) 1732 MHz (13 x 133) instead.
  I will be grateful for any advice.

  Hey Buddy

  I put t know what you are talking about, and I don t know if you're up-to-date on CPU technology but the laptop was equipped with the Intel Pentium Dual - Core T2370 processor.
  I recommend the Intel page on Intel Dual-Core T2370 properties.

  This processor supports Enhanced Intel SpeedStep technology.
  Do you know what it is?

  Here is a short info from the Intel page:

  + Enhanced Intel SpeedStep technology allows the system to dynamically adjust the frequency of voltage and core processor, which can translate into a reduction in average energy and decreases heat production average. +

  I think it should be clear now.

• to the footer in the library file does not change on the site

  I looked for a colleague who uses dreamweaver. I need to change an e-mail address to request information on this site. When I make the change on the footer file in the library and download it, it does not change on the site. Is there more than that? Thank you!

  change on the footer file in the library and download it, it does not change on the site. Is there more than that? Thank you!

  You update the library item, then locally update all the pages that contain this element of the library and then download all the modified pages (that work)?

  or are you simply update the library item file and then download this library file (who doesn't)?

• Change the wallpaper off the admin account and the background recording does not

  Hello

  I'm having a problem with my background. Whenever I try to put a picture on my computer as background will not be set that image as it is, and when I put a picture of the internet as a background it will fix but don't stay once I restart the computer. This is the case EVERY TIME.

  After seeing this happen several times I went to control panel > appearance and personalization > change wallpaper. What I get on this page is a simple line, "this feature has been disabled, please contact your administrator." The problem is I AM the administrator and I have never changed the parameters of the Office to act like that, and I certainly never turn off any of the display settings.

  I scoured these forums and I've seen people who have similar problems (but not admin issues I'm having and not the problem with the setting of a local image) and have tried some of the solutions, including going in the ease of access settings > make computer easier to see and to erase the settings is unchecked.

  Help, please!

  All the solutions I am about to propose involve not to change the registry. Since it is to change the registry I recommend that you first create a point in http://www.howtogeek.com/howto/windows-vista/create-a-restore-point-for-windows-vistas-system-restore/ restoration system AND back up the registry as follows: http://www.adamsdvds.co.uk/tutorials/vista/regedit/backup.php.  I also want to warn to do at your own risk and peril - I have not tried these procedures myself, so I can't speak to their effectiveness or what other impact that may lead to changes.  But if you do the safety precautions backup two above, you should be able to recover in case this does not work or something you want starts to occur.  The decision (and risk) is your enttirely.

  Here is an article with a possible solution: http://www.pchell.com/support/desktopwallpaper.shtml.

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Here's another registry solution that I found in a forum:

  Remove after your system using Regedit registry entry. Disconnect and reconnect.

  [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
  "Wallpaper"=""

  You should be able to change your background now.

  ===================================================================================================================

  Here's yet another article on how to solve the problem with yet another type of editing the registry: http://www.tech-pro.net/how-to-change-desktop-wallpaper.html.

  I hope that one of these options help.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• The event log does not start error 31: a device attached to the system is not functioning

  I can't get the service to start on my winxp sp3 pc event log. I have tried everything I know:

  • Running sfc/scannow
  • Reset permissions
  • Search for malware and viruses
  • Rebuild the WMI
  • Create a new account
  Nothing seems to work, I think that this is related to an error in hardware/device, but I see no problem in Device Manager. Can someone point me in the right direction to get this resolved? I don't really want to have to format or restore my PC...
  Thank you.

  * EDIT * well it seems to have fixed myself, I used regedit and navigate to the key:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\EventLog
  
  
  There, I found some records, I deleted the folder "Powershell" and the "Internet Explorer" folder, and the event log service, and then began. I had uninstalled IE and Powershell but these records were still there so I thought I would like to remove to see if he has made all the difference.
  Thanks for your time!
  -Antoni

• When I change the main mxml file in the project and then export the swf file does not change, why?

  I have an existing project, years ago that I need to change, I am using Flash Builder 4. When I export the project, it creates a SWF in bin-release, then when I change the code in the mxml project file or files of any format and export the swf file needs to change, but it's not. You have an idea why this might happen?

  Thank you

  I found the problem, there was a SWF into the html-template folder within the project. This has led to substitute the swf of the new generation.

• DNG files exported from the LR4 showing does not changes made when opened in PSE10?

  I have LR4, and once I do some changes that I exported the files I want to use DNG.  Then I open them in PSE10 to make final changes.  It has been working well, in fact I had an old version of Adobe Raw in my PSE on my other computer.  Then when I opened to post-secondary studies, he would ask if I wanted to convert to compatible version for editing in camera raw.  I always says no b/c I have has no need to do more raw edits.  Now that I've installed PSE on my new computer, it has the new version of ACR I guess.  When I open the DNG Edit now I no longer have this error message, but it's to show my contrast, etc. as an action setting raw instead of the changes I made in LR.  Some are like vibrance, but "recovery" that I know is "strong points" in LR, and other things are not displayed correctly.  I know that the options are different, but I don't want to use the ACR settings he uses when I open the file, or have to go through them again.  I'm not there is something I'm missing, but he cannot know.  Thanks for any help!

  There is zero advantage to sending files DNG at the PSE. As you can see, you're not see your changes and get different sliders in PSE, and indicates that certain types of ACR version mismatch. And since you say you are done making the FIRST changes, this wastes just opening time of the DNG in the PSE/ACR interface that you will not use...

  Rather than send the DNG PES files, send a TIF file to PSE using the command of Lightroom Photo-> change, and this TIF will open directly in the editor, with all of your changes from Lightroom intact PSE.

• the keyboard layout does not change stuck in American English.

  Original title: stuck in American English

  I was using my laptop with the keyboard moving between French or British English that I didn't ask, no problem this morning. Now he has decided to keep on American English, no matter what language, the taskbar says he uses. I did not put that American English is at all today. Help, please!

  Thank you, but have been there, what did somehow.
  Did not any changes that I knew. Also had bees through the diagnostic steps suggest you, but not joy. My husband has finally solved the problem: he found a small icon (somewhere lower right scale) that looks like a keyboard and it was worth it-set to U.S. English, but where he found I do not have a clue and have never managed to find since!

• Why the file size does not change when I use "Process multiple Images" to add a watermark?

  Hello

  I use 11 elements. To add a watermark to a lot of JPG photos at the same time, I use the function 'process multiple files.

  I select a source folder and a destination folder and adds a number to three numbers for each file. I do NOT check the box marked 'change photo size. After that, I set the watermark I want printed on my photos and hit OK. All files in the source folder are processed and saved with a new name in the destination folder. Loyally.

  But. The file size of the new file is strongly reduced, compared to the original. He's going from 10 MB to 500 KB (in general). Why is this? Is there a way I can help?

  Kind regards

  / Mikael Lindgren

  File size reduction is the effect of jpeg compression. In the process several files dialog, check the bottom option "convert files to the format" and choose "jpeg max quality.