Switch - r of ping does not

Similar Questions

• 2000-2D02TU HP: HP 2000-2D02TU Power LED power switch but the laptop does not start.

  Someone help me.

  HP 2000-2D02TU Power LED power switch but the laptop does not start.

  What I'm doing.

  Please help me

  Model No. - HP 2000-2D02TU

  Hello @Alok_Bhai,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems, with the help of the community!

  I read your post on the laptop won't start does not and wanted to help you!

  You indicate that the lights are flashing, but the laptop does not start?  If this is the case, try to review the following document and let me know how it goes:

  Computer does not start and emits a LED or beep Code

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Light (switch) on my screen does not turn off. I have to shut my computer down several times a day to turn off the monitor.

  Light (switch) on my screen does not turn off.  So, I shut down my computer and restart several times a day, because when I put it in mode 'sleep', he wakes to the top in a few minutes and will not fall asleep.  I could put a blanket on my screen when not in use, but I'd rather find a way to make it stay asleep when I tell him.

  Light (switch) had already done once before and I was so worried that once I turned off the monitor that I would never get it new on... a bit short of money here, to buy a new monitor, but the next day, I pressed the power button with an additional downward pressure and I could so he could start working again (able to turn the market monitor).  It was about 3 weeks ago.  Now, the light stays green, unless I stop the whole computer.

  Maybe my main problem is sleep mode, which removes the screen for like 2 minutes and then he wakes up to the top and is so rude when I myself and try to sleep, I just turn off the monitor everytime I put the computer to sleep.

  Now, I can't turn off the monitor, except by turning off the computer.

  Hi JDandGinger,

  I suggest you follow the provided article and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-power-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-monitor-and-video-card-problems

  If the problem still persists contact the manufacturer of the monitor for more help and information.

• Switch signals and Wireless does not work on Satellite A660

  I have laptop Satellite A660 17 M AND I am facing a PROBLEM THAT IS THE WIRELESS DO SWITCH NOT RUN AND did not SWITCH THE WIRELESS ADAPTER ON or OFF
  AND ALSO ON THE TOP OF THE KEYBOARD FUNCTION BUTTONS DOES NOT WORK

  AFAIK, the utility Vap and flashcard support are responsible for these functions. You can try to download and install them

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

  Note, first you must install the utility of vap and restart the support belt utility and Visual support cards, then

• Site-to-Site VPN Ping does not

  I configured a vpn site-to site between two firewalls ASA 5505. Establishes the tunnel, but the icmp traffic does not pass. In fact, ping worked twice, but only at random. I need to work on a regular basis. I have attached the configurations as well as an output of the packet - trace both of the ASA and the IPSec and its ISAKMP. Thanks for any help you can provide.

  ASA Configuration 1:

  ASA Version 8.0 (3)

  !

  hostname asa1

  activate the encrypted password of A.zMQonBIU0NmOC0

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.50.253 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 1.1.1.1 255.255.255.240

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  OMV1AjIsWknnKr9H encrypted passwd

  boot system Disk0: / asa803 - k8.bin

  passive FTP mode

  acl_out list extended access permit tcp any host 63.76.12.195 eq smtp

  acl_out list extended access permit tcp any host 63.76.12.195 eq www

  acl_out list extended access permit tcp any host 63.76.12.195 eq 3389

  acl_out list extended access permit tcp any host 63.76.12.195 eq ftp

  acl_out list extended access permit tcp any host 63.76.12.195 eq ftp - data

  acl_out list extended access permit tcp any host 63.76.12.195 eq telnet

  acl_out list extended access permit tcp any host 63.76.12.195 eq 5800

  acl_out list extended access permit tcp any host 63.76.12.195 eq 5900

  acl_out list extended access permit tcp any host 63.76.12.195 eq https

  acl_out list extended access permit tcp any host 63.76.12.196 eq www

  acl_out list extended access permit tcp any host 63.76.12.196 eq https

  acl_out list extended access permit tcp any host 63.76.12.196 eq smtp

  acl_out list extended access permit tcp any host 63.76.12.196 eq 3389

  acl_out list extended access permit icmp any one

  access-list 101 extended allow ip 10.1.50.0 255.255.255.0 10.1.40.0 255.255.255.0

  access-list 101 extended allow ip 10.1.50.0 255.255.255.0 10.1.51.0 255.255.255.0

  vpn-fargo extended ip 10.1.50.0 access list allow 255.255.255.0 10.1.51.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool ippool 10.1.40.1 - 10.1.40.254

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM image disk0: / asdm - 523.bin

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0

  static (inside, outside) 1.1.1.2 tcp ftp 10.1.50.3 ftp netmask 255.255.255.255

  static (inside, outside) 1.1.1.2 tcp ftp - data 10.1.50.3 ftp - data netmask 255.255.255.255

  static (inside, outside) 1.1.1.2 tcp telnet 10.1.50.3 telnet netmask 255.255.255.255

  static (inside, outside) tcp 1.1.1.2 5800 10.1.50.102 5800 netmask 255.255.255.255

  static (inside, outside) 1.1.1.2 tcp 5900 10.1.50.102 5900 netmask 255.255.255.255

  static (inside, outside) 1.1.1.2 tcp 3389 10.1.50.5 3389 netmask 255.255.255.255

  static (inside, outside) 1.1.1.3 10.1.50.6 netmask 255.255.255.255

  Access-group acl_out in interface outside

  Route outside 0.0.0.0 0.0.0.0 1.1.1.0 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  card crypto mymap 20 match address vpn-fargo

  card crypto mymap 20 peers set 2.2.2.2

  card crypto mymap 20 transform-set RIGHT

  crypto mymap 20 card value reverse-road

  mymap outside crypto map interface

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 20

  preshared authentication

  aes-256 encryption

  sha hash

  Group 5

  life 86400

  crypto ISAKMP ipsec-over-tcp port 10000

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  internal group vpn3000 strategy

  attributes of the strategy group vpn3000

  value of server WINS 10.1.50.5

  value of 10.1.50.5 DNS server 10.1.50.6

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value 101

  asa1.com value by default-field

  disable authentication of the user

  the address value ippool pools

  encrypted vpn Tw.atDK7GScnXkMJ password username

  vpn tunnel-group type remote access

  VPN tunnel-group general attributes

  Group Policy - by default-vpn3000

  jtvpn group of tunnel ipsec-attributes

  pre-shared-key *.

  tunnel-group 2.2.2.2 type ipsec-l2l

  2.2.2.2 tunnel-group ipsec-attributes

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  inspect the icmp error

  !

  global service-policy global_policy

  context of prompt hostname

  : end

  ASA 2 configuration:

  ASA Version 8.2 (1)

  !

  hostname asa2

  activate the encrypted password of A.zMQonBIU0NmOC0

  1vU9VISnc.IQ6OSN encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.51.253 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address 2.2.2.2 255.255.255.240

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  vpn - dsm extended ip 10.1.51.0 access list allow 255.255.255.0 10.1.50.0 255.255.255.0

  IP 10.1.51.0 allow Access-list extended sheep 255.255.255.0 10.1.50.0 255.255.255.0

  access outside-access list extended icmp permitted an echo

  outside-access extended access list permit icmp any any echo response

  outside-access extended access list permit all all unreachable icmp

  access outside-access allowed list icmp exceed all once

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 0.0.0.0 0.0.0.0

  access-outside group access component software snap-in interface outside

  Route outside 0.0.0.0 0.0.0.0 2.2.2.0 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES esp-3des esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  card crypto mymap 10 correspondence address vpn - dsm

  card crypto mymap 10 set peer 1.1.1.1

  card crypto mymap 10 game of transformation-ESP-3DES

  crypto mymap 10 card value reverse-road

  mymap outside crypto map interface

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 20

  preshared authentication

  aes-256 encryption

  sha hash

  Group 5

  life 86400

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  tunnel-group 1.1.1.1 type ipsec-l2l

  tunnel-group 1.1.1.1 ipsec-attributes

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the icmp

  inspect the icmp error

  !

  global service-policy global_policy

  context of prompt hostname

  : end

  Packet trace of ASA1:

  asa1 (config) # entry packet - trace within the icmp 10.1.50.253 1 1 detailed 10.1.51.253

  Phase: 1

  Type: FLOW-SEARCH

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Not found no corresponding stream, creating a new stream

  Phase: 2

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 0.0.0.0 0.0.0.0 outdoors

  Phase: 3

  Type: ACCESS-LIST

  Subtype:

  Result: DECLINE

  Config:

  Implicit rule

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd49dcce0, priority = 500, area = allowed, deny = true

  Hits = 5, user_data = 0 x 6, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 10.1.50.253, mask is 255.255.255.255, port = 0

  DST ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: drop

  Drop-reason: flow (acl-drop) is denied by the configured rule

  Packet trace of ASA2:

  asa2 (config) # entry packet - trace within the icmp 10.1.51.253 1 1 detailed 10.1.50.253

  Phase: 1

  Type: FLOW-SEARCH

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Not found no corresponding stream, creating a new stream

  Phase: 2

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 10.1.50.0 255.255.255.0 outside

  Phase: 3

  Type: ACCESS-LIST

  Subtype:

  Result: DECLINE

  Config:

  Implicit rule

  Additional information:

  Direct flow from returns search rule:

  ID = 0xc9583648, priority = 500, area = allowed, deny = true

  hits = 9, user_data = 0 x 6, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 10.1.51.253, mask is 255.255.255.255, port = 0

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: drop

  Drop-reason: flow (acl-drop) is denied by the configured rule

  ASA 1 IPSec security association:

  peer address: 2.2.2.2

  Tag crypto map: dynmap, seq num: 10, local addr: 1.1.1.1

  local ident (addr, mask, prot, port): (10.1.50.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (10.1.51.0/255.255.255.0/0/0)

  current_peer: 2.2.2.2

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  decaps #pkts: 5, #pkts decrypt: 5, #pkts check: 5

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  endpt local crypto. : 1.1.1.1, remote Start crypto. : 2.2.2.2

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500

  current outbound SPI: 1F3E7E3A

  SAS of the esp on arrival:

  SPI: 0x1DFAE5E0 (502982112)

  transform: esp-3des esp-md5-hmac no

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 77824, crypto-card: dynmap

  calendar of his: service life remaining (KB/s) key: (3824999/28036)

  Size IV: 8 bytes

  support for replay detection: Y

  outgoing esp sas:

  SPI: 0x1F3E7E3A (524189242)

  transform: esp-3des esp-md5-hmac no

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 77824, crypto-card: dynmap

  calendar of his: service life remaining (KB/s) key: (3825000/28034)

  Size IV: 8 bytes

  support for replay detection: Y

  ASA 1 ISAKMP Security Association:

  1 peer IKE: 2.2.2.2

  Type: L2L role: answering machine

  Generate a new key: no State: MM_ACTIVE

  ASA 2 IPSec security association:

  peer address: 1.1.1.1

  Tag crypto map: mymap, seq num: 10, local addr: 2.2.2.2

  list of access vpn - dsm allowed ip 10.1.51.0 255.255.255.0 10.1.50.0 255.255.255.0

  local ident (addr, mask, prot, port): (10.1.51.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (10.1.50.0/255.255.255.0/0/0)

  current_peer: 63.76.12.194

  #pkts program: 5, #pkts encrypt: 5, #pkts digest: 5

  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 5, comp #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  endpt local crypto. : 2.2.2.2, remote Start crypto. : 1.1.1.1

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500

  current outbound SPI: 1DFAE5E0

  SAS of the esp on arrival:

  SPI: 0x1F3E7E3A (524189242)

  transform: esp-3des esp-md5-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 81920, crypto-map: mymap

  calendar of his: service life remaining (KB/s) key: (4374000/27900)

  Size IV: 8 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  outgoing esp sas:

  SPI: 0x1DFAE5E0 (502982112)

  transform: esp-3des esp-md5-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 81920, crypto-map: mymap

  calendar of his: service life remaining (KB/s) key: (4373999/27900)

  Size IV: 8 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  ASA 2 ISAKMP Security Association:

  1 peer IKE: 1.1.1.1

  Type: L2L role: initiator

  Generate a new key: no State: MM_ACTIVE

  Hi Mike,.

  I see the following in your configuration:

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  Sequence number of Th for the peer 2.2.2.2 is 20 so we first hit the dynamic map that could cause this problem.

  To avoid this, I suggest you do the following:

  No map mymap 10-isakmp ipsec crypto dynamic dynmap

  map mymap 65535-isakmp ipsec crypto dynamic dynmap

  To validate this fact, if you look at the SA on ASA1 ipsec, you will find that it was negotiated with dymap (card crypto seq 10) and not 20!

  ASA 1 IPSec security association:

  peer address: 2.2.2.2

  Tag crypto map: dynmap, seq num: 10, local addr: 1.1.1.1

  local ident (addr, mask, prot, port): (10.1.50.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (10.1.51.0/255.255.255.0/0/0)

  current_peer: 2.2.2.2

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  decaps #pkts: 5, #pkts decrypt: 5, #pkts check: 5

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  Hope this helps!

  See you soon,.

  Manasi!

• Switch Windows user option does not work

  Windows Switch User Option is not Working.please help.if, anyone can remotely my computer please solve my problem.ihave tried myself to resolve according to the method of microsoft but failed.please response and solve my problem quickly.

  Hi AbdullahEjaz,

  1 find the computer on a domain network?

  2 did you do changes on the computer before the show?

  I suggest you to refer to the following articles and check if it works.

  Fast User Switching option is not available

  http://support.Microsoft.com/kb/280758

   

  A discussion on the availability of the fast user switching feature

  http://support.Microsoft.com/kb/294739

  Let us know if that helps.

• UCS - East West switching... Does not I think

  Hi all hope you can enlighten us.

  I have understood that the FI switch East West traffic, had a problem tonight where we removed Unplugged the South North portchannels at the Network Layer 3 to upgrade the kernel and all virtual machines in the UCS lost connectivity between them even if they are on the same VLAN.

  So question is should downing uplinks really stop east west switching?

  Hope you can shed some light,

  Thank you

  Assuming that end host for Ethernet mode: f you have vnic on the transmitter connected to the fabric A, the vnic to the destination to the fabric B, both on the same Vlan. then your traffic will leave the area of the UCS to the North and re-enter UCS on the other fabric.

  Turning on the FI - A doesn't happen, if same vnic Van and initiator and target on A fabric.

  Hope that clarifies your situation.

• I use Edge CC 2014. When I open actions of a particular object (or code view) "the screen switches from code snippets' does not appear. Is there a setting preferably I'm missing?

  I can not get the code snippets to display. What I'm missing here?

  Hi John,.

  Yes, code snippets are currently only available in the Actions Panel. You can access the Actions panel for various items by clicking on the button Actions open to the left of the item in the assets Panel or line stage, or to the right of the ID of the item in the properties panel. It's the button that looks like a pair of braces: {}

  HTH,

  Joe

• 6 sec new settings slider switch does not stay on (green)

  Switch used in environments does not stay on (green). When you try to configure the settings of the store, music, Apps and sliding switches books are moving reluctantly to green, stay green for a second or less and then back to white.  I want these settings to stay 'on' (green).

  Check

  Settings > general > Restrictions > accounts > allow editing (checked)

  Note, you must enable restrictions to see/do changes.

• Ping bb8520 blackBerry Smartphones does not

  My ping does not work on bb8520 but protect everything else like apps, internet, bb, etc work!

  Thanks for providing the info.

  I sent a PIN message to two BlackBerry smartphones and it shows that it has been delivered at the time.

  I suggest to uninstall BBM by going to Options > management of applications and games of the BBM and press menu and select Delete.  Then, restart the BlackBerry Curve.

  Go to the go to www.blackberry.com/bbm and download this new version and back on once more the BlackBerry Curve and then test.

  Let me know if you have any other questions.

  See you soon.

• Check sensor SFR with FireSight via VPN - does not work

  Hello security experts.

  I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor.

  Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN?

  The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem?

  Thank you very much!

  Remi

  Hello

  If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then.

  Can try you to ping from sensor to DC:

  ping -M do -c 20 -s 1572 

  By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works. See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere. Best regards, Aastha Bhardwaj rate if this is useful!

• 4 finger swipe does not work under macOS Sierra!

  Hey all, I upgraded to macOS Sierra and noticed that one of my function used more regularly on Mac OS, 4 finger swipe to switch between desktop computers does not work! Mine is an April 2011 MacBook Pro.

  Earlier, 2 fingers sliding back in the files, similar to switching back and forward for the Web pages in Safari, has been abandoned without reason penetrable. I hope that's not the same fate for 4 finger swipe to switch between desktops.

  I probably use hundreds of times every day for switching between desktop computers because I have safari, MS Word and open the mail outside of iTunes on separate workstations. I hope that a fix is released soon!

  Apple, do not bite of useful outdoors features!

  Ravi Reddy

  4 finger swipe works for me and appears as the 2nd part of the Trackpad Control Panel.

• Spaces does not work properly

  I have a Retina Display 27-inch iMac. Although spaces were working in El Capitan, including slide 2 fingers (mouse) to slide between spaces and assigning specific to alternative spaces applications (for example, iTunes has been assigned to the office 2).

  After the transition to macOS Sierra, I can still use spaces of Mission control, by selecting a space in the jobs at the top of the screen after pressing F3. However, swiping two fingers on the mouse (this gesture is enabled) or launch an iTunes of the 1st (it is assigned to the office 2) results in immediate disconnection and the reappearance of the login screen. No matter what method of switching of spaces that does not directly through Mission control causes this disconnection/connection. I tried to reset the SMC, without success.

  It is originally a major crimp in my workflow that I have requests assigned to various work stations and must be able to launch them directly in these spaces and drag from one to the other as I could with El Capitan.

  Everything else under macOS Sierra seems to work fine. Any help would be greatly appreciated. I think this may be a problem with corruption of preference files because I also installed macOS Sierra on a Mac Mini with a hp monitor and spaces seems to work fine on this machine.

  Hi Dahlgren.

  I see that you encounter a problem with spaces on your Mac since the update to Mac OS Sierra.  I understand that it is important to resolve this, because it affects your workflow, and I'm happy to offer assistance.  It would be useful to further isolate this issue, if you create a new administrator account on the Mac, to see if the problem persists.  Here are the instructions to help you get started and please let us know how it goes.

  How to test a question in another account on your Mac.

  Thank you for using communities of Apple Support.

  See you soon!

• Volume of material control does not not on Portege M200

  I have a new Portégé M200.
  The sound works perfectly and I can control it through the software volume control (e.g. in control panels, taskbar,...)
  But the material volume control (rotary switch on board before) does not work. I have checked all the manuals, dash (Volume, SoundMAX,...) but can't find anything.

  What's wrong?
  -marc

  Hi Marc

  This is obviously a defect of material. AFAIK there is no adjustment for volume control dial on the front button of the Portege. This button cannot be enabled or disabled. I put t know how old is your device, but I assume that the warranty is still valid. Contact the Service partner and let check the device. Warranty will cover all costs.

  Good bye

• Updates do not install, Sections of Vista does not and cannot start the Audio Service

  I try to install the updates on windows update but important as the service package 2 do not work, they start then stop and say failed code "WindowsUpdate_80070643"

  boxes keep popping up saying some files are damaged or not installed properly and that I should reinstall as a file call... system32\AVRT.dll. Windows Media is not no longer works.

  My Audio service is not running, I'm not sure that there is a problem in microsoft windows but the button to switch on the audio does not, and a box pops up saying it does not yet have another pop up says that everything works.

  any help? Please

  Hello
   
  a. updates have you tried to install?
  (b) button to switch on the audio of your computer are you using?
  c. what exactly happens when you try to run any audio/video file?

  You can try the steps outlined in the article below and check if this help.
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  For audio problem you are trying to run the troubleshooter which may help. It search common problems with your volume settings, your sound card or driver and your speakers or a headset.

  1. open the troubleshooting of Audio playback by clicking the Start button, then Control Panel.
  2. in the search box, type troubleshooting, and then click Troubleshooting. Under hardware and sound, click on the audio playback problems. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  You can also try to update check you and sound card driver if it works. The article below will help you do.

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Also, check if the following services are set to automatic.
  a. Windows Audio
  b. Windows Audio Endpoint Builder

  Here's how:
  1. click the Start button, type services.msc and press ENTER.
  2. go to any services mentioned above at the same time, right-click on it and select Properties
  3. click on the tab general, select automatic for startup type. Also click the Start button, if it is not started.
  4. click the Dependencies tab and make sure that all addictions services are set to automatic. Then click on the OK button.

  After return to that exact error messages we can help you better.

  Let us know if it works.

  Kind regards
  Umesh P - Microsoft Support