Switches Cisco stackable, 500 and the consolidation of NETWORK cards

Similar Questions

• Load balancer and the consolidation of NETWORK cards

  Hello

  We recently had to our file VMware Server after a bit nasty failure of his original material.  Since we moved, it mostly worked OK, but we don't get the occational network shares paw when large files are thrown on.

  ESXi host, sure it works use 5Gbit ethernet adapters on the same Virtual Switch.  Looking at the traffic it would seem that all traffic flows in just a single NETWORK adapter and it is not much at all through the others.  Is something that I need to set it up so that it can better load balance between network cards?  Or is it a document anywhere who recommended settings for multiple network cards?

  I found a vDS topic but we have not undertaken more liciencing on most of our servers.

  We run VSphere 4.1 via the Vcentre server.

  Thanks for the help.

  faster4233 wrote:

  What you say makes a little more sense on what I see.  There is very little traffic flowing through other NETWORK cards, but is perhaps because there isn't any real traffic goes to them.  I thought that VMware may use multiple NICs, if it was required that is why I thought I'd see more data on the other.

  Curiosity is anyway that I can combine NICs for more flow using VMware?

  The load balancing, you can achieve with VMware is not a "real" load balancing, this is more a static distribution of traffic in accordance with the policy, you have chosen.

  You use means that according to the virtual switch port ID the vNIC to the host is connected to a specific bear is chosen. This unique vNIC traffic will use this bear as long as this bear does not fail. In this case the guests more with vNIC, you have the better are used Teddy.

  Other policies can be better for other scenarios. For example, 'Hash IP' uses the source IP address and target to choose a teddy bear. It is a good policy for a server with a vNIC single file and many different communication partners. The 'Source Port' policy route all traffic through a teddy bear so that 'Hash IP' policy would use many Teddy as not what ID port is used, but the communications partners. And a file server must have many of them, more than it has of vNIC.

  AWo

  VCP 3 & 4

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• core VM and the consolidation of NETWORK cards

  Hello

  By default, VM network ports group is associated with two vmnic and the management ports group is connected to one vmnic. Is there a reason for this?

  

  This isn't really a default configuration.

  By default would be vmk0-> vSwitch0-> vmnic0 - just an uplink to the default vSwitch.

  It seems that someone is gone, has added the vmnic1 to your vSwitch0 and configured the active adapters / Eve / unused. To clear the reason for this, you have to love the person responsible for this change.

  Could also be a config after installation automatically, depends on how you installed your ESXi host.

• Help with the consolidation of NETWORK cards

  I have a box blade with several blades attached to the switch blade.  Read the doc and experimentation, it seems that with the parameter 'link status only' blades will never be aware of the problems of network beyond the connection between the blade and the local switch.

  For example, I have install NIC teaming with:

  Nic0 = active

  NIC1 = standby

  By causing a failure on the way to nic0 (beyond the switch), I lost the connection and the day before not to enter in action.

  Question 1:

  When you never use (is an auxiliary card not almost useless)?

  Question 2: (I really need an answer for this one)

  Assuming that you use Active/active instead of the active / standby * and *.

  You have a network outage where esxi is not aware of the outage * and *.

  Everything which load balancing option you are using happens to try to send down the wrong path...

  The load balancer alogrythm keep trying this wrong way forever and never try the other path?

  NB - I know hadou "beacon probing" option but most ay docs to not use it.

  Thank you

  Hello

  What blade case are you help and who past did they? Various switches have a function for example Cisco Monitoring of State of the link that allows to disable contactors blade interfaces internal fail all the external interfaces. This means that you should never get into a position whereby the upstream link failure will go unnoticed.

  Concerning

• NB100 supplied with Bluetooth and the slot for sim card

  I wonder what model come with bluetooth and the slot for sim card,.

  The NB100? Have a look at the brochures on the Toshiba site.

• the name of the local computer network card limit has been exceeded

  noticed that my domain root name has been defined for the replication of the dns to the domain only. When I tried to return to the replication with the forest, I got the above message. It will obviously be let me no change without correction of this error. No other error message appears in the newspapers.

  Hi Monroetech,

  You can read the following article and check if it helps:

  Error message: the name of the local computer network card limit has been exceeded

  Hope this information is useful.

• Need quick help on vmkfstools, cloning and the consolidation of the snapshot - not sure that I am doing things

  I received this a.p..:

  I modified the parentCID in "Datapark.SBS2011 - 000003.vmdk" to attach the instantaneous chain. " What I would say, it is to upload the file to the data store and then clone the virtual disk so that the current data files remain intact in case something does not work as expected.

  To clone the virtual disk, run the following command:

  vmkfstools 'Datapark.SBS2011 - 000002.vmdk'-i ' Datapark.SBS2011 - Clone.vmdk '-d thin - one Free

  The command uses Datapark.SBS2011 - 000002.vmdk - who is the last file of active snapshot of the string - as the source and creates a virtual clone drive, in which all the data from all the snapshots will be consolidated. Once the cloning is done, you can join the clone of a virtual machine. Depending on what happened while the Basic virtual disk was attached to a virtual machine, there could be corruption. However, due to the size of snapshots, you should be able to recover most of your data.

  Probably, he fell asleep, and I need to start as soon as possible the cloning.

  Is it OK to run the command, or it deletes all the files in the snapshot?

  As he says, "so that the current data files remain intact in case somethoing won't", the clone command seems to remove all the files from the snapshot.

  Anyone who can confirm?

  Best regards

  Morty

  vmkfstools 'Datapark.SBS2011 - 000002.vmdk'-i ' Datapark.SBS2011 - Clone.vmdk '-d thin - one Free

  
  

  Is it OK to run the command, or it deletes all the files in the snapshot?

  It won't do anything for your source files.

  It will simply read the string of the delta with the base of your virtual machine disk and the Clone in a consolidated file called ""Datapark.SBS2011 - Clone.vmdk " "

• Shared members and the consolidation process

  Hi guys,.
  
  I work to give support to a HFM application and I need some advice, because I'm a bit confused. I have 4 different graph of entities:
  
  (1) ComConsol
  (2) legal
  (3) BGroups
  (4) alternate
  
  I was trying to lock the ComConsol data in a grid when I realized that the status is CN. I have run the consolidation and status changed by OK. However, legal, BGroups and Deputy changed their status to CN. When I run the legal consolidation, then ComConsol must be consolidated again.
  I think it might be related to some shared members, but I'm not sure.
  Any advice?
  
  Thank you, guys.

  It seems to me that you run all consolidate them with data or consolidate all instead of consolidating on the parent entity? Other options, you force calculated a base entity or a rule executed affecting the State of one or more basic entities.

• R12 implementation level and the Consolidation of the Instance

  Hello
  
  We have 11.5.10 HRMS on IBM AIX and Financials 11.5.10 on Sun Solaris servers. The plan is to upgrade the Applications for R12 and consolidate instances in a single case.
  Please share your experiences to first upgrade the applications for R12 and then make the Instance Consolidation or do the Consolidation of the Instance on 11.5.10 and then perform the upgrade.
  
  What are the advantages and disadvantages of the two approaches.
  
  Please share your experiences, if someone has worked on similar projects.
  
  Kind regards
  VN

  I would say do the consolidation then upgrade the instance, this way you can avoid upgrading twice - please log an SR to confirm this with the support of the Oracle.

  Thank you
  Hussein

• Problems with the formula of Member and the consolidation

  Hello
  
  I have a cube that contains information about a number of funds. Information we hold is to these two funds level (ie. the price of the various funds, the status of funds) or at the level of the transaction (say. premiums and claims transactions).
  
  The outline looks a bit like this.
  
  Account
  -Premium +.
  -Claims.
  -Taking P/L + (UDA: HoldingP/L)
  Transaction type
  -Units ~
  -Value ~
  Profit/loss ~
  -Price ~
  -Status ~.
  -Calc profit/loss ~ (see formula below)
  Fund
  -AAA +.
  -AAB +.
  -AAC +.
  -etc.
  Time
  -Jan_10 dynamic Calc
  --05 - jan +.
  --06 - jan +.
  
  Now I have a formula a little complex, sitting in the Calc profit/loss as follows Member
  
  IF (@ISLEV (account, 0))
  
  IF (@ISUDA (' HoldingP/L' account))
  IF ('Status' == 0)
  'Result '.
  ON THE OTHER
  Do a calc more fantasy based on different price and the units of the other members of the account;
  ENDIF
  OTHERWISE other calc
  ENDIF
  
  ON THE OTHER
  @SUM (@CHILDREN (@CURRMBR (account)));
  ENDIF;
  
  
  Now this calc seems to work for yourself and give me the answer I want. However, I am having a problem trying to get back to the level of the Member of Jan_10. While my other types of transactions seem fine, consolidate the profit/loss Calc going widely indicated.
  
  I've identified what I think it is, but I don't know how I could fix it.
  
  Because I have my days the value of consolidation, which basically means that it adds set ups for Jan_10, prices of all individuals of the day. This tilts the calculation rather that just add to the top individual days Calc Profit/Loss, he's trying to calculate the Jan_10 totals.
  
  Does make sense? If this isn't the case, I could whip up a quick table of data showing the problem.

  Have you tried setting the calc member two passes?

  It is quite complex, so it might not help, but worth it. Give it a try.

• Satellite A75 - switch wireless works only with the Intel wireless network adapter

  The Atheros card that came with my Satellite A75 had questions, so I installed an Intel 2200.
  According to Device Manager, everything works and is properly installed and should work, but the message I get is the wi - fi switch.

  It is placed at the position, but the indicator light lights up and the Intel card does not connect without it. The light comes on with the Atheros, but this card hangs the system.

  A few months ago, I borrowed an Intel 2200 on an IBM and put it in the A75 temporarily and it worked fine, that's why I bought the Intel.

  I tried the FN + the button with the antenna, but no effect, even if it also works with the Atheros.
  Y at - it another way to activate the wi - fi in addition to the switch and the FN, or is there a way to disable the switch function if the computer doesn't even know it's there?

  Maybe it works.

  Thank you.

  Solved! If anyone has this problem, here is the link to fix:
  http://www.TechSpot.com/VB/all/Windows/t-18046-p-2.html

• Retired HP Pavilion a6000n PC and can not find the driver for Network Card card do? Download Driver?

  Gradient of the Visa OS came with the PC for XP.  Installed new HD and partitioned drive so there is no pass file.

  I found that it is management of network integrated 10/100 Base-T interface but cannot find the manufacturer to use it Web site.  In addition, been

  playback ChipSet might need drivers or upgrade?  Don't know that much about this, but enough to get in trouble if

  I'm not "coached" through it all.  Low grade was the Visa MS HP accompanying MS XP Professional.                               Need a link or help find the Driver for the network card.

  Thank you.

  Thank you very much... which seems to do the job for letting me use the network card.  Once I installed the chipset you me too, my IE was able to get the net.  The only thing that happened that I wonder about, what I choose to accept or not something RAID, which I accepted and it seems to work with one small annoying side affect: I can't get Windows Update to run.  I get this error: 0x8024400a and I spent literally hours looking for and trying different solutions, which none have worked. Do you think that there is something that would change this Nvidia software which would cause that?   I get out to the internet OK and can go to any web page.  It runs a bit slow, but I thought it might be because I'm using a newly installed Win XP and it has only 2 SP.  My next step in getting this thing to work was to run Windows Update and anti-virus stuff set.   Any way, thanks again for your help.

• I returned to windows 7 on my laptop Acer 5253 10 Windows and I lost my network card driver in the process.

  * Original title: jake

  I returned to windows 7 Windows 10 on my laptop Acer 5253, apparently, I lost my network card driver in the process. I want to download a network card for a usb key to solve the problem, but I don't know how. I have no internet access on the Acer so I can't download directly. I not had a disc with disks on it to Acer, they came preloaded. I am running windows 7 pro on the Acer and Dell desk top on as I type. Can someone HELP me understand this? I am not at all computer savvy and need help.

  Using another computer, visit the ACER support for your computer and download the drivers for a USB.

• Windows xp and the problem of network 7 printer connectivity

  a computer running Windows XP Connect to Dell 2335dn printer using the http: and is connected properly.  Second computer running Windows 7 by using the same Http info cannot connect to the gateway is 192.168.1.101 printer is 192.168.1.110 than the path of the computer network xp is http://192.168.1.110:631 so my real question is what I have to change the 631 to another number for the computer to windows 7 to connect?

  Hello

  1. you have any security program installed on the Windows 7 machine?

  2. were you able to access the printer prior to this problem?

  3. do you receive any error messages?

  4 did you a recent software or changes to the material on the computer?

  Method 1:

  I suggest you run the printer Troubleshooter and check if it helps.

  Open the printer Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 2:

  I also suggest you go through the steps mentioned in the link and the Coachman.

  Sharing files and printers with different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/help/sharing-files-and-printers-with-different-versions-of-Windows

  Method 3:

  I also suggest to ping the IP address of the printer from a Windows 7 Administrator command prompt and let us know the result.

  a. Click Start and type cmd in the Search box.

  b. right click on cmd in the list programs, and then click run as administrator.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue

  c. at the command prompt, type the command, and then press ENTER:

  See also;

  Select the file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows7/file-and-printer-sharing-frequently-asked-questions

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  Hope this helps and keep us posted.

• T60, XPPro and the disappearance of network connections

  I have a client with a T60 (2623-D7U). I got it in a month with no network connection in Device Manager or in the Panel. Both wireless (WWAN and 802) did not work or could be found and cable is not connected. After having worked several frustrating days of research I reinstalled XPPro (factory reinstall) and wired. I dropped a wireless card and the client was happy.

  Now I have it back.

  Yet once he was missing two connections. This time, I rebooted and did some jiggery pokery and managed to get the map Wi - Fi and back visible and connected, but still no WWAN.

  My question is, this is a topic? I suspect that the WWAN hardware is originally from Wi-wired and repeated problems. Someone at - it firm clues beyond what I have already done?

  Thanks Andy, XP Pro has been mentioned in the post a couple of times, but I had tried all the MS corrects the previous (a month ago) occasion before the clean install.

  It is early in the morning, when I posted, I thought I might try a hardware solution so lifted the T60 keyboard (4 to 6 screws on the back) and found the two wireless devices arising therefrom. I prick and pushed, but has not removed the. Reassembly and restart, the EVDO device reappeared after an absence of more than a month. The wireless, 802, however, is still AWOL. Then I guess is to unscrew the 2 screws on each wireless device (they look identical) and remove/relocate to own PCB connections.

  Sounds of?

  Without worrying about progress and this message can help others.