"SymSetSymWithAddr64 not found in the dynamic library DBGHELP.dll.

Similar Questions

• the procedure entry point SymSetSymwithAddr64 could not be found in the dynamic library DBGHELP.dll

  the procedure entry point SymSetSymwithAddr64 could not be found in the dynamic library DBGHELP.dll

  Here's a quick fix, do not guarantee to fix but it's worth it.

  Look for your operating system for dbghelp.dll drive. Check the advanced options, search records system, search for hidden files and folders, and search subfolders. Close programs as much as possible. Make sure the results show one in Windows/system32 and other in Windows\system32\dllcache. Right-click on the Windows /system32 and delete it. Wait a few seconds and the supplementary search. You should see it was added back in the dllcache folder and we're in recycler as the image below...

  NOTE: My Windows is under WINNT. Yours is probably Windows.
  

  Restart the computer and see if the problem goes away.

• Could not load the turbo tax software & this message "the EncodePointer point procedure entry is not found in the dynamic library KERNELL32.dll.

  Original title: while loading turbo tax software & this message. The procedure entry point EncodePointer be found in the dynamic library KERNELL32.dll.     can someone tell me how to solve this problem?

  I have windows xp 2002 Service Pack 2

  Hi henryjeshom,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Uninstall and reinstall the application of Turbo tax.

  How to change or remove a program in Windows XP

  http://support.Microsoft.com/kb/307895

  Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  If the problem persists, contact support for Turbo tax for more help and information.

  http://TurboTax.Intuit.com/support/

• The 62 ordinal not found in the dynamic library CSCDLL.dll

  I get this message every time I open adobe acrobat: the 62 ordinal could not be located in the dynamic link library cscdll.dll. I am running Windows Vista Home Premium SP2 32-bit on an HP desktop. I get a message for a few months. Made sure that Windows and Acrobat is up-to-date.

  Hi BP69,

  ·         When the issue occurred?

  Follow these steps and see if it resolves your problem:

  Method 1:

  Check if there is a cscui.dll C:\Windows\SysWOW64 folder.

  The cscui.dll does not exist by default in the C:\Windows\SysWOW64 folder.

  So if you find the cscui.dll on the C:\Windows\SysWOW64 you can try right click and rename the cscui.dll to cscui.old.

  Method 2:

  Scan your computer for viruses using your antivirus software or online a scanner to flush out them (as appropriate).

  http://OneCare.live.com/site/en-us/default.htm?keyword=scannerhome

  Method 3:

  Start your machine in "safe mode with network" and check if the problem persists.

  Safe mode with networking

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Method 4: I recommend you perform the clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I hope this helps.

• installed the plug-in for adobe cs4 3rd part. When I open the plugin I get an error saying _CFBundleCopyFileTypeForFileData of procedure entry point is not found in the dynamic library CoreFoundation.dll. This can be corrected?

  Adobe photoshop cs4 with 3d invigorator plugin zexworks

  Hi brush jamie.

  Welcome to the Microsoft Answers site!

  You may need to contact the Support from Adobe to see if they have a fix for it. Follow the link below the disclaimer to access using Adobe:

  http://www.Adobe.com/support/

  Hope this information was useful.
   
  Concerning

  Varun j: MICROSOFT SUPPORT

  Visit our Microsoft answers feedback Forum

  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and let us

  know what you think.

  NOT MS. LINK:
  Important note: this response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.

• NtrigApplet - unable to connect to the driver: failed to open device___TVAgent.exe - Entry Point not found the procedure entry point PowerReadACValue could not be found in the dynamic library POWRPROF.dll

  Hi all

  I have a HP TouchSmart tx2-1025dx Notebook PC Vista... I met 2 large pop-up windows that will not close & appear as soon as I turn on my computer gives me a time DIFFICULT to access anything whatsoever...

  They read as follows:

  NtrigApplet - unable to connect to the driver: failure to open the device

  TVAgent.exe - Entry Point not found the procedure point PowerReadACValue entry is not found in the dynamic library POWRPROF.dll

  CAN SOMEONE PLEASE HELP?
  THANK U :)

  Hi the apprentice 85,

  Remember to make changes to the computer before that happened?

  Looks like the problem is hardware or software related, I suggest you follow the below mentioned steps below to refine the question

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

   

  Step 2: Put the computer to boot to determine which program is causing the problem

  Follow step 1 in the link below,

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not the computer to start normal follow step 7 in the link.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error message: Setup.exe - Ordinal not found - the 62 ordinal could not be locatedin the dynamic library CSCDLL.dll, Quickbooks 2012 run

  Original title: error Ordinal 62
  I received the following error sporadically when I try the accounting version of Quickbooks 2012.  Accordingly, it does not run Quickbooks on my desktop but it allows me to run on my laptop.  Help, please.  "Setup.exe - Ordinal not found - the 62 ordinal could not be locatedin the CSCDLL.dll dynamic link library.

  Hello

   

  You can try the following steps and check.

   

  Method 1:

  Check if there is a cscui.dll C:\Windows\SysWOW64 folder.

  The cscui.dll does not exist by default in the C:\Windows\SysWOW64 folder.

  If you find the cscui.dll on the C:\Windows\SysWOW64 you can try right click and rename the cscui.dll to cscui.old.

  Method 2:

  You can run scanning of the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

  For more information, you can consult the following link.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Method 3:

  You can also perform a clean boot and check.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  You can also check the following thread link and check.

  WARNING 62 Ordinal not found in cscdll.dll

• Registry entry point to restart application not found in the dynamic library KERNEL32dll; Error - smaxpnp.exe - point of entry not found

  When I reboot, or start my system I get an error - smaxpnp.exe - not found entry point

  Hello

  Have you made changes on the computer before this problem?

  Smax4pnp.exe is a system process that belongs to the software SoundMAX. It is not necessary for sound to work on your computer, but is mainly used to run or adding components to the software SoundMAX program.

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Step 1:

  Start safe mode and check if the problem persists there.

  A description of the start in Windows XP Mode options:

  http://support.Microsoft.com/kb/315222

  Step 2:

  Put the computer in a clean boot state, then start in normal mode and check if it helps.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: once you have completed troubleshooting try the steps to configure Windows to use a Normal startup state.

  Method 2:

  Try to remove the smax4pnp.exe of your computer and check if it helps.

  Follow the steps to remove smax4pnp.exe:

  a. Press 'Ctrl', 'Alt' and 'Delete' on your computer to open the Windows Task Manager. "Click on the"Processes"tab on top.

  b. scroll down and click on "Smax4pnp.exe." Click 'End process' to stop the currently running process

  c. click on the Windows "Start" button, then click 'Search'. Click on "Search all files and folders" on the left panel to open the search box.

  d find and delete this file: Smax4pnp.exe.

  e. empty the trash to complete uninstallation.

  Hope the information is useful.

• Error, "the point procedure entry SUnMapLS_IP-EBP_28 be found in the dynamic library KERNEL32.dll." during installation "manufacturer of T-Shirt Hanes.

  Original title: Point of entry not found

  I'm trying to run an old program, Manufacturer of T-Shirt Hanesand get the error, "the entry point of procedure SUnMapLS_IP-EBP_28 not found in KERNEL32.dll dynamic link library.
  I'm running Vista 32 bit.
  Any help would be greatly appreciated.

  Hello

  1 see if that helps you.

  Right-click on the setup.exe > and then select run as administrator to install it.

  2. ask the manufacturer to program if it is Vista Compatible.

  We can not help you with that that Microsoft no longer has the link Vista Compatibility Center available.

  3. If the program is not Compatible Vista, install in Windows Compatibility Mode

  "Using Windows 7 or Vista Compatibility Mode.

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

  See you soon.

• Get FL.exe - Entry Point not found 'point of entry procedure for NtAlpcSendWaitReceivePort not found in the dynamic link library ntdll.dll' error at boot fruity loops.

  Original title: ntdll.dll error at boot fruity loops.

  get FL.exe - Entry Point not found 'point of entry procedure for NtAlpcSendWaitReceivePort not found in the dynamic link library ntdll.dll' error when I try to start fruity loops after installing Kies from samsung for the new phone. How can I fix this error? Help, please. Thanks in advance! :)

  Hello
  I suggest you contact support FL. I couldn't find all of the resources for this program.
  Eddie B.

• "the 495 ordinal not found in the dynamic link library urlmon.dll" produces 10 times every reboot

  I am running MS Vista on my laptop. Recently when I start up I get the message "the 495 ordinal not found in the dynamic link library urlmon.dll" in a popup box and must cancel 10 times before I can move forward.

  I thought somehow it may relate to a recent update that has been accepted for Skype on my system.  So I uninstalled Skype.  Attempts to reinstall Skype have failed.  the installed app, but I cannot arrive at a login screen.  Instead of the normal Skype window, I have just the bottom of loading in a web browser.

  I found a similar one but transposed ordinal error discussed 459 in the KB and I tried following many of its steps (+ my results):

  "Method 1:

  To resolve this problem in Internet Explorer, follow these steps:

  a. Quit all programs that are running.

  b. Click Start and then click Run.

  c. type regsvr32 urlmon.dll, and then click OK.

  d. When you receive the message "DllRegisterServer in urlmon.dll succeeded," click OK.

  ('DllRegisterServer in urlmon.dll' received successful)

  If this does not resolve the issue, repeat steps 2 through 4 for each of the following files (in step 3, replace Urlmon.dll with each of the names of files below):

  ·         Shdocvw.dll (failed)

  ·         Actxprxy.dll (failed)

  ·         Oleaut32.dll (failed)

  ·         Mshtml.dll (received no response)

  ·         Browseui.dll (failed)

  ·         Shell32.dll (managed)

  Method (step 2):

  I suggest you to start in safe mode and test the question.

  Safe boot mode: http://windows.microsoft.com/en-US/windows-vista/Start-your-computer-in-safe-mode

  Method (step 3):

  I suggest you perform a SFC Scan and check if it helps.

  The tool (SFC.exe) System File Checker scans missing or system corrupted files and repairs them.

  How to use the System File Checker tool to troubleshoot missing or corrupted system files on Windows: http://support.microsoft.com/kb/929833

  (SFC Scan completed successfully)

  Side note: when I started in Mode safe I immediately received an error "Microsoft Visual C++ Runtime library"Application request time to close in an unusual way"

  DavidMCandy suggested the user a list of the URLMON. Dll on the system.  I did as well.  See the file on my Onedrive to

  http://1drv.Ms/11PQ3dm

  I hope this will help you to find me a solution to my problem.

  First of all lets run a startup repair.

  This hardware test (and other things but we want to test the equipment). To do maintenance on the database and the files used by your two frequent falls (related to how windows manages system files including Windows Update). SFC is also linked to this, so we know that certain parts are working.

  After return from the logs generated.

  Startup Repair

  If your computer has a single operating system installed, repeatedly press the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again. [Correction to start - Help and Support].

  In the Display Options Options Advanced startup, use the arrow keys to highlight repair your computerand press ENTER.

  Select the Startup Repair tool.

  Startup Repair makes a log file. See C:\Windows\System32\LogFiles\Srt\SrtTrail.txt.

  To access if Windows does not start, in the Advanced Boot Options screen, use the arrow keys to select repair your computerand press ENTER.

  Select command prompt.

  Type

  type C:\Windows\System32\LogFiles\Srt\SrtTrail.txt | more

   

  More details about the error

  To decode 0 x 80070002. X 0 means that it is a hexadecimal number, 8 , error, the first 7 means it a windows error and the rest of Eastern 2, the number, the Windows error.

   

  To search for the error message we need to decimal format. Start the Calculator (Start - All Programs - Accessories - calculator) and choose the menu display - scientific, then the menu display - Hex. Enter 2 Menu display - decimal. It will say 2.

   

  Start an command prompt (Start - All Programs - Accessories - command prompt) and type

   

  net helpmsg 2

   

  and it will say

   

  The system cannot find the specified file.

   

  Use Notepad to search for FATAL and and the specific error code (for example, 80070002) in C:\Windows\Windowsupdate.log.

  Also check the cbs.log newspaper. You must follow these steps. You should check at the beginning and end of the troubleshooting. To make life easy, empty the file first, do the update, read the file. Otherwise, there will be tens of thousands of lines to read.

  Look for the lines saying error or failed.

  Run Microsoft Fixit

  Microsoft has a range of automatic programs to solve common problems. To see Windows Update problems

  http://support.Microsoft.com/mats/windows_update/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  del %SYSTEMROOT%\Logs\CBS\CBS.log

  Install the update

  Notepad %SYSTEMROOT%\Logs\CBS\CBS.log

  Which helps with Windows Update.

  The system update tool

  Also run the system update readiness tool

  For 32-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=504

  For 64-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=1540

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  Notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

  Repair and defragment the database

  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   

  SC stop wuauserv

   

  stop bits SC

   

   

  SC stop cryptsvc

  Esentutl.exe/p/o c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe /d c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

   

  SC start cryptsvc

   

  SC start bits

   

  SC start wuauserv

   
  Difficulty of the Service
   
  Download wuauserv_Vista_32.reg from https://skydrive.live.com/redir?resid=E2F0CE17A268A4FA 121
   
  Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the wuauserv_Vista_32.reg.
   
  Reset
   
  Click Start - All Programs - Accessories - right on command prompt and choose Run as administrator. Type (or copy the lines below and a blank line under and right click in the command prompt window and select Paste). This will start the dependent services in the correct order.
   
  If you get an error message you can copy by do right click in the window, choose the brand, by selecting the text and press Efriendship.
   

  SC start DCOMLaunch

  SC start RpcSs

  start wuauserv sc config = auto

  SC start wuauserv

  departure from trustedinstaller sc config = request

  SC start trustedinstaller

  SC config COMSysApp start = demand

  SC start COMSysApp

  SC config BITS start = demand

  SC start BITS

  start slsvc sc config = auto

  SC start slsvc

  SC config start = auto EventLog

  SC start EventLog

  
  --

  More details about the error

  To decode 0 x 80070002. X 0 means that it is a hexadecimal number, 8 , error, the first 7 means it a windows error and the rest of Eastern 2, the number, the Windows error.

   

  To search for the error message we need to decimal format. Start the Calculator (Start - All Programs - Accessories - calculator) and choose the menu display - scientific, then the menu display - Hex. Enter 2 Menu display - decimal. It will say 2.

   

  Start an command prompt (Start - All Programs - Accessories - command prompt) and type

   

  net helpmsg 2

   

  and it will say

   

  The system cannot find the specified file.

   

  Use Notepad to search for FATAL and and the specific error code (for example, 80070002) in C:\Windows\Windowsupdate.log.

  Also check the cbs.log newspaper. You must follow these steps. You should check at the beginning and end of the troubleshooting. To make life easy, empty the file first, do the update, read the file. Otherwise, there will be tens of thousands of lines to read.

  Look for the lines saying error or failed.

  Run Microsoft Fixit

  Microsoft has a range of automatic programs to solve common problems. To see Windows Update problems

  http://support.Microsoft.com/mats/windows_update/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  del %SYSTEMROOT%\Logs\CBS\CBS.log

  Install the update

  Notepad %SYSTEMROOT%\Logs\CBS\CBS.log

  Which helps with Windows Update.

  The system update tool

  Also run the system update readiness tool

  For 32-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=504

  For 64-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=1540

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  Notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

  Repair and defragment the database

  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   

  SC stop wuauserv

   

  stop bits SC

   

   

  SC stop cryptsvc

  Esentutl.exe/p/o c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe /d c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

   

  SC start cryptsvc

   

  SC start bits

   

  SC start wuauserv

   
  Difficulty of the Service
   
  Download wuauserv_Vista_32.reg from https://skydrive.live.com/redir?resid=E2F0CE17A268A4FA 121
   
  Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the wuauserv_Vista_32.reg.
   
  Reset
   
  Click Start - All Programs - Accessories - right on command prompt and choose Run as administrator. Type (or copy the lines below and a blank line under and right click in the command prompt window and select Paste). This will start the dependent services in the correct order.
   
  If you get an error message you can copy by do right click in the window, choose the brand, by selecting the text and press Efriendship.
   

  SC start DCOMLaunch

  SC start RpcSs

  start wuauserv sc config = auto

  SC start wuauserv

  departure from trustedinstaller sc config = request

  SC start trustedinstaller

  SC config COMSysApp start = demand

  SC start COMSysApp

  SC config BITS start = demand

  SC start BITS

  start slsvc sc config = auto

  SC start slsvc

  SC config start = auto EventLog

  SC start EventLog

  
  --

  More details about the error

  To decode 0 x 80070002. X 0 means that it is a hexadecimal number, 8 , error, the first 7 means it a windows error and the rest of Eastern 2, the number, the Windows error.

   

  To search for the error message we need to decimal format. Start the Calculator (Start - All Programs - Accessories - calculator) and choose the menu display - scientific, then the menu display - Hex. Enter 2 Menu display - decimal. It will say 2.

   

  Start an command prompt (Start - All Programs - Accessories - command prompt) and type

   

  net helpmsg 2

   

  and it will say

   

  The system cannot find the specified file.

   

  Use Notepad to search for FATAL and and the specific error code (for example, 80070002) in C:\Windows\Windowsupdate.log.

  Also check the cbs.log newspaper. You must follow these steps. You should check at the beginning and end of the troubleshooting. To make life easy, empty the file first, do the update, read the file. Otherwise, there will be tens of thousands of lines to read.

  Look for the lines saying error or failed.

  Run Microsoft Fixit

  Microsoft has a range of automatic programs to solve common problems. To see Windows Update problems

  http://support.Microsoft.com/mats/windows_update/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  del %SYSTEMROOT%\Logs\CBS\CBS.log

  Install the update

  Notepad %SYSTEMROOT%\Logs\CBS\CBS.log

  Which helps with Windows Update.

  The system update tool

  Also run the system update readiness tool

  For 32-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=504

  For 64-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=1540

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  Notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

  Repair and defragment the database

  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   

  SC stop wuauserv

   

  stop bits SC

   

   

  SC stop cryptsvc

  Esentutl.exe/p/o c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe /d c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

   

  SC start cryptsvc

   

  SC start bits

   

  SC start wuauserv

   
  Difficulty of the Service
   
  Download wuauserv_Vista_32.reg from https://skydrive.live.com/redir?resid=E2F0CE17A268A4FA 121
   
  Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the wuauserv_Vista_32.reg.
   
  Reset
   
  Click Start - All Programs - Accessories - right on command prompt and choose Run as administrator. Type (or copy the lines below and a blank line under and right click in the command prompt window and select Paste). This will start the dependent services in the correct order.
   
  If you get an error message you can copy by do right click in the window, choose the brand, by selecting the text and press Efriendship.
   

  SC start DCOMLaunch

  SC start RpcSs

  start wuauserv sc config = auto

  SC start wuauserv

  departure from trustedinstaller sc config = request

  SC start trustedinstaller

  SC config COMSysApp start = demand

  SC start COMSysApp

  SC config BITS start = demand

  SC start BITS

  start slsvc sc config = auto

  SC start slsvc

  SC config start = auto EventLog

  SC start EventLog

  
  --

  More details about the error

  To decode 0 x 80070002. X 0 means that it is a hexadecimal number, 8 , error, the first 7 means it a windows error and the rest of Eastern 2, the number, the Windows error.

   

  To search for the error message we need to decimal format. Start the Calculator (Start - All Programs - Accessories - calculator) and choose the menu display - scientific, then the menu display - Hex. Enter 2 Menu display - decimal. It will say 2.

   

  Start an command prompt (Start - All Programs - Accessories - command prompt) and type

   

  net helpmsg 2

   

  and it will say

   

  The system cannot find the specified file.

   

  Use Notepad to search for FATAL and and the specific error code (for example, 80070002) in C:\Windows\Windowsupdate.log.

  Also check the cbs.log newspaper. You must follow these steps. You should check at the beginning and end of the troubleshooting. To make life easy, empty the file first, do the update, read the file. Otherwise, there will be tens of thousands of lines to read.

  Look for the lines saying error or failed.

  Run Microsoft Fixit

  Microsoft has a range of automatic programs to solve common problems. To see Windows Update problems

  http://support.Microsoft.com/mats/windows_update/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to a folder on your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  del %SYSTEMROOT%\Logs\CBS\CBS.log

  Install the update

  Notepad %SYSTEMROOT%\Logs\CBS\CBS.log

  Which helps with Windows Update.

  The system update tool

  Also run the system update readiness tool

  For 32-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=504

  For 64-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=1540

  To view the results click on start - all programs - accessories - right click on command prompt and choose Run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  Notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

  Repair and defragment the database

  Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type (or copy and paste by clicking in the command prompt window and choose Paste).
   

  SC stop wuauserv

   

  stop bits SC

   

   

  SC stop cryptsvc

  Esentutl.exe/p/o c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe /d c:\Windows\SoftwareDistribution\DataStore\DataStore.edb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb

  Esentutl.exe/p/o c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

  Esentutl.exe /d c:\Windows\System32\catroot2\{F750E6C3-38EE-11D1-85E5-00C04FC295EE}\catdb

   

  SC start cryptsvc

   

  SC start bits

   

  SC start wuauserv

   
  Difficulty of the Service
   
  Download wuauserv_Vista_32.reg from https://skydrive.live.com/redir?resid=E2F0CE17A268A4FA 121
   
  Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the wuauserv_Vista_32.reg.
   
  Reset
   
  Click Start - All Programs - Accessories - right on command prompt and choose Run as administrator. Type (or copy the lines below and a blank line under and right click in the command prompt window and select Paste). This will start the dependent services in the correct order.
   
  If you get an error message you can copy by do right click in the window, choose the brand, by selecting the text and press Efriendship.
   

  SC start DCOMLaunch

  SC start RpcSs

  start wuauserv sc config = auto

  SC start wuauserv

  departure from trustedinstaller sc config = request

  SC start trustedinstaller

  SC config COMSysApp start = demand

  SC start COMSysApp

  SC config BITS start = demand

  SC start BITS

  start slsvc sc config = auto

  SC start slsvc

  SC config start = auto EventLog

  SC start EventLog

  
  --

• The 12404 ordinal not found in the dynamic link library mfc90u.dll.

  I get this error when trying to open Samsung Kies 3 after the new facility:

  The 12404 ordinal not found in the dynamic link library mfc90u.dll.

  This error is almost identical to the one posted here, but that the error was to 7426 ordinal and is since a couple of years.  However, I tried the recommended fix (install Visual C++ 2008 SP1) that obviously works for MANY people, but this does not change my problem.

  I have re-installed and rebooted several times, and I searched my system for the dll specified could not be found:

  -C:\Windows\winsxs\amd64_microsoft.VC90.mfc_1fc8b3b9a1e18e3b_9.0.30729.6161_none_044aad0bab1eb146 (date: 25/07/2014;) Size: 4.86 MB)

  -C:\Windows\winsxs\x86_microsoft.VC90.mfc_1fc8b3b9a1e18e3b_9.0.21022.8_none_b81d038aaf540e86 (date: 05/09/2014;) Size: 1.10 mb)

  -C:\Program Files (x 86) \Samsung\Kies3\FirmwareUpdate (Date: 07/05/2014;) Size: 3.60 MB)

  -C:\Program Files (x 86) \Samsung\Kies3 (Date: 07/05/2014;) Size: 3.60 MB)

  The first two files seem to be temporary files (dated 9/5 can come from the current installation of Visual C++).  The last two I know come with Kies 3 installation - I searched the dll both before and after the reinstallation of the product.

  If Kies 3 cannot locate the dll file in the dynamic link library, perhaps I can copy the dll in that location?  If so, where is this place?

  Other thoughts on how to fix this?

  Windows: Windows 7 Enterprise Edition, Service Pack 1

  Kies 3 Installer: Version 3.2.14083.9

  I get this error when trying to open Samsung Kies 3 after the new facility:

  The 12404 ordinal not found in the dynamic link library mfc90u.dll.

  This error is almost identical to the one posted here, but that the error was to 7426 ordinal and is since a couple of years.  However, I tried the recommended fix (install Visual C++ 2008 SP1) that obviously works for MANY people, but this does not change my problem.

  I have re-installed and rebooted several times, and I searched my system for the dll specified could not be found:

  -C:\Windows\winsxs\amd64_microsoft.VC90.mfc_1fc8b3b9a1e18e3b_9.0.30729.6161_none_044aad0bab1eb146 (date: 25/07/2014;) Size: 4.86 MB)

  -C:\Windows\winsxs\x86_microsoft.VC90.mfc_1fc8b3b9a1e18e3b_9.0.21022.8_none_b81d038aaf540e86 (date: 05/09/2014;) Size: 1.10 mb)

  -C:\Program Files (x 86) \Samsung\Kies3\FirmwareUpdate (Date: 07/05/2014;) Size: 3.60 MB)

  -C:\Program Files (x 86) \Samsung\Kies3 (Date: 07/05/2014;) Size: 3.60 MB)

  The first two files seem to be temporary files (dated 9/5 can come from the current installation of Visual C++).  The last two I know come with Kies 3 installation - I searched the dll both before and after the reinstallation of the product.

  If Kies 3 cannot locate the dll file in the dynamic link library, perhaps I can copy the dll in that location?  If so, where is this place?

  Other thoughts on how to fix this?

  Windows: Windows 7 Enterprise Edition, Service Pack 1

  Kies 3 Installer: Version 3.2.14083.9

  Installation under pakage will solve the problem

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=d5692ce4-Adad-4000-abfe-64628a267ef0&displaylang=en

• the 6848 ordinal is not found in the dynamic link library mfc90u.dll

  Hello

  (I hope) a brief history of my problem:

  I am running Windows 7 Professional (64 bit) on a VM (VirtualBox software) on my computer of Linux Mint.  I tried to run a program called Filemaker Pro Runtime, (name of original file FMPROR. EXE.  First of all, I get the error "the side to side configuration is incorrect" and after a few hours of internet browsing, checking the logs etc, I found that I had to install Visual C++ Runtime (x 86, 2008 version) that I found and installed.  Only concern was the page I have d/led (which was a Microsoft page) does not mention Win 7 system requirements - I have tried to find a version for Win7, but a search increase no relevant results.  So I installed the version I found, by Windows XP, Win Server and Vista (I think it may have been an old page).  This seemed to fix the side-by-side configuration error, but now I get the error:

  the 6848 ordinal is not found in the dynamic link library mfc90u.dll

  I tried a search on the web using the above string, but the closest results, mentioning only a .dll ordinal and various different seemed not really relevant.

  I would be very grateful if someone could help me find the required information fix it, score at least me to a Web page that will help me to understand.  I'm not a geek, but I'm pretty OK with research and implementation of aid on the web, but this time, I'm confused as to how to proceed.

  Thank you very much in advance for any help received

  See you soon

  Ricky Walker

  Hello

  Version of Windows 7

  http://www.Microsoft.com/en-in/Download/details.aspx?ID=5555

  MFC Package security update Microsoft Visual C++ 2008 Service Pack 1

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=26368

  See if that helps.

• Error message "the 421 ordinal not found in the dynamic link library urlmon.dll" whenever I start my computer

  Original title: 421 ordinal could not be located in the dynamic link library urlmon.dll

  I get this error every time I start my computer: "the 421 ordinal not found in the dynamic link library urlmon.dll.

  In the control panel select Problem Reports and Solutions (problem of type in)
  The START searchbox), go to the history of the problem, your mistake right click and choose
  Check the Solution.
   
  In administrative tools, choose the reliability and performance monitor and
  Click on MonitoringTools then the reliability monitor (type of reliability in research
  at startup). This list is a chart of the software installs, uninstalls, Windows
  updates and crashes by date. See if your plant started to occur after
  you installed or uninstalled something.
   
  You can clean boot
  Troubleshooting http://support.microsoft.com/kb/331796
   
  Download http://www.nirsoft.net/utils/shexview.html
  Disable all non-microsoft shell extensions (to explore) and reactivate a
  by so this can help.
  --
  ..
  --
  "Mr_Xtatic" wrote in message news: 63562fcd-7837-420-b-84e0-854170dfae5c...
  > I get this message error everytime I start my computer: "the ordinal 421.
  "> could not be located in the dynamic link library urlmon.dll"
   
   

• the 459 ordinal not found on the dynamic link library urlmon.dll.

  I have windows 7 ultimate and I download call of duty 4 and I can't run that it because the 459 ordinal has not located in the dynamic link library urlmon.dll.

  Please help me

  Hello

  Please contact the Microsoft Community.

  I would have you first save the .dll file.

  To do this, please open the command prompt and then paste this command. Press enter when finished-

  regsvr32 urlmon.dll

  If this does not work, then I have you uninstall and reinstall the game as well.

  In addition, I would like to you contact the game for still - assitance support

  https://support.steampowered.com/kb_article.php?ref=8746-WDHC-4827

  We know if you need help.