SyncRep between SAS and SATA pools

Similar Questions

• Disks hard SAS and SATA in mixture with controller H730 R730

  I try to set up a new server for our SMEs and wanted to know if I could use say hard 2 SAS drives in raid 1 configuration for hyper-v (r2 2012) host then use 6-2 TB of SATA drives in pass-through mode for use with storage for 2 VMs.

  Bobc007,

  The rule with the help of SAS and SATA drives is that you CAN mix the two in the same controller. You not CAN NOT mix SAS and SATA in the same virtual disks well. The configuration you are looking for is a supported configuration.

  Let me know if this helps answer your questions.

• ASUS P6T7 WS - SAS and SATA RAID-0 / boot

  
  

  I am trying to determine the optimal configuration of HD to better use
  the 2 x SAS and 6 x SATA connections on the motherboard P6T7.
  I intend to fill all 12 available bays 3.5 "in the Lian Li PC-A77F and want
  to control all devices SATA 12 of the Mo without the use of an expansion card.

  
  

  1. is it effective to use a x 4 SAS to SATA fanout cable to configure a
  equipped with four SATA RAID-0 drives on one SAS channel?

  
  2. is it effective to use a x 4 SAS to SATA fanout cable to connect one
  SATA boot drive drive 1 + + 2 optical drives on one SAS channel data?
  (I realize boot must be BIOS configured via the Marvell SAS host utility)

  
  3. should I stick to a plan 'a channel and a device' and use the add-on controller
  for the SATA device rest four bays?

  
  4. If the answer to ' 3 is in the affirmative, what is the best use of channels 2 x SAS if all the»
  There are SATA devices? (bootable disk. optical media, or just a single SATA drive)

  
  

  Thank you

  1.

  I don't think that it is possible to use this motherboard connector fan-out cable single to multiple disks disk

• You can mix SAS and SATA drives in a RAID 1 PowerEdge T110 II configuration

  Hello

  I have a RAID 1 configuration and one of the two drives in the array has failed.  I've removed and replaced by another drive hoping the Dell Perc adapter H200 would rebuild the mirror automatically, but it does not.  In Server Admin OpenManage virtual disk displays as degraded.  The issue I think may be the replacement drive is SATA where the original was SAS.

  Is there a way you can make the adapter accepts a SATA drive or is it simply not supported?

  SIV

  Hello.

  Dell controllers, including the H200 are not supported mixing SAS, SATA or SSD in the same table. They may, however, each separately constitute a virtual disk on the same controller. Consider replacing the disk failing another identical or higher capacity SAS drive.

• H200A PERC. SAS and SATA. Simple 2 extra HARD drives raid. Possible?

  Hello.
   
  Research in the server rack dell R210 II.
   
  Added records 2 x 300 GB SAS with a PERC H200A raid controller.
  The other two empty drive bays im looking to transfer courses two SATA 2.5 "HARD disk drives. Ive read you can mix SATA and SAS drives, is this true?
   
   
  I have two options to the raid configuration:
   
  the raid controller would be able to support two raid 1 RAID. 1 for the SAS drives and the other for the two SATA drives?   Operating system can see two disks.
   
  He would support a raid 1 for hard 1 & 2 discs.  Then with disk HARD 3 & 4 show the HARD drive directly on the server.  OS sees thre readers.  The drive in question and two others.
   
   
  I tried the dell chat, but could not get anywhere, as the helpdesk agent does not seem to know that you can google some caddy and buy the caddy to adapt to discs with no carts.

  [murmur] I'm wrong :), but I think the H200 supported not RAID, so if left unconfigured, the disks will be seen by the operating system as the person/no RAID disks.  Also, if I am wrong not :), the H200 supports a maximum of 2 virtual drives, so would not work two 1-disk RAID 0 and a RAID 1 (in fact, it probably won't allow you to create a single drive RAID 0 in all). [/whisper]

  http://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_dell_adapters/PowerEdge-RC-h200_User ' s%20Guide_en-us.pdf

  Sorry... I love you pc :)

• Mix HD Sas and Sata on the T410 with controller Perc H700 [CF]

  We have a customer using a Sever T410 with Raid Perc H700 controller; We want to add more space to that the creation of a new virtual disk with the connector 1 (now does not).

  Can we add 2 new Sata HD 2 TB of space on new Vdisk also during the first Vidsk is the use of Sas 10 K 300 GB HD?

  We ha 2

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could come message privato mandarmi it service tag of server?

• Relationship between SAS & Esxi

  Hello

  I have hard SAS Extore XJ-SA12-316R with 16 TB storage space, I have connected to my server HP (DL380 G5) with mini sas port and I want to use with Esxi V5.

  I have configured the raid 6 + 0 with two spare parts that format is NTFS GPT, I can not connect my SAS to ESXi, although I can't see any storage when I add on Esxi, but when I install just a windows 2008 R2 server on my server I can see SAS storage on disk management! Could you please tell me how to get communicate between SAS and Esxi? It makes me crazy!

  Try this, I tested it successfully;

  Copied the VIB for temp folder;

  ~ # ls - lh /tmp/
  -rw - r - r - 1 root root 24.8 k 9 December 2011 scsi-stex - 4.07.0000.75 - 1OEM.500.0.0.472560.x86_64.vib

  Install the VIB, by using the - v switch;

  
  

  ~ # software esxcli vib install v - /tmp/scsi-stex-4.07.0000.75-1OEM.500.0.0.472560.x86_64.vib
  Result of the installation
  Message: The update completed successfully, but the system must be restarted for the changes to be effective.
  Restart required: true
  VIBs installed: Promise_bootbank_scsi - stex_4.07.0000.75 - 1OEM.500.0.0.472560
  VIBs deleted:
  VIBs ignored:

  After a reboot, it is available;

  
  ~ List of the vib # esxcli software | grep stex

  Name Version Date seller installation acceptance level
  --------------------  ----------------------------------  -------  ----------------  ------------

  SCSI-stex 4.07.0000.75 - 1OEM.500.0.0.472560 promised VMwareCertified 2012-11-28

  I was also able to remove with success;

  ~ # software esxcli vib remove scsi-stex - n
  Result of deleting
  Message: The update completed successfully, but the system must be restarted for the changes to be effective.
  Restart required: true
  VIBs installed:
  VIBs removed: Promise_bootbank_scsi - stex_4.07.0000.75 - 1OEM.500.0.0.472560
  VIBs ignored:

  ... again, this requires a restart of the host.

  Post edited by: jrmunday - post reboot added control.

• Re: Sat Pro A10 and Sat 10 - the difference - need new keyboard

  Hey all!

  New ID as I am garbage to remember the passwords/log on emails...

  I have a Satellite Pro A10, which needs a new keyboard - there's loads are circulating on ebay for Satellite A10 - but not the Pro - now I'm almost 100%, it'll be the same keyboard - right? the 'Pro' ILO denounces just usually extras bits and things qhizzy-, but basically they are the same hardware platform slot - i.e. the same keyboard between the A10 Sat and Sat Pro A10

  Anyone?

  : D thank you in advance for letting me sleep at night!

  I agree with you. There is not much difference, and the construction of the laptop is the same.
  I'm 100% sure that the keyboard is the same.

• VPN between ASA and cisco router [phase2 question]

  Hi all

  I have a problem with IPSEC VPN between ASA and cisco router

  I think that there is a problem in the phase 2

  Can you please guide me where could be the problem.
  I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

  Looking forward for your help

  Phase 1 is like that

  Cisco_router #sh crypto isakmp his

  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

  and ASA

  ASA # sh crypto isakmp his

  ITS enabled: 1
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 1

  1 peer IKE: 78.x.x.41
  Type: L2L role: initiator
  Generate a new key: no State: MM_ACTIVE

  Phase 2 on SAA

  ASA # sh crypto ipsec his
  Interface: Outside
  Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

  Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
  19.194.0 255.255.255.0
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer: 78.x.x.41

  #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: C96393AB

  SAS of the esp on arrival:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4275000/3025)
  Size IV: 8 bytes
  support for replay detection: Y
  outgoing esp sas:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac no
  running parameters = {L2L, Tunnel}
  slot: 0, id_conn: 7, crypto-card: Outside_map
  calendar of his: service life remaining (KB/s) key: (4274994/3023)
  Size IV: 8 bytes
  support for replay detection: Y

  Phase 2 on cisco router

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x0 (0)

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  protégé of the vrf: (none)
  local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
  current_peer 87.x.x.4 port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  Errors #send 0, #recv 0 errors

  local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
  Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
  current outbound SPI: 0x3E9D820B (1050509835)

  SAS of the esp on arrival:
  SPI: 0xC96393AB (3378746283)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4393981/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0x3E9D820B (1050509835)
  transform: esp-3des esp-md5-hmac.
  running parameters = {Tunnel}
  Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
  calendar of his: service life remaining (k/s) key: (4394007/1196)
  Size IV: 8 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  VPN configuration is less in cisco router

  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
  access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

  sheep allowed 10 route map
  corresponds to the IP 105

  Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

  mycryptomap 100 ipsec-isakmp crypto map
  the value of 87.x.x.4 peer
  Set transform-set mytransformset
  match address 101

  crypto ISAKMP policy 100
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  ISAKMP crypto key xxx2011 address 87.x.x.4

  Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

  You currently have:

  Extend the 105 IP access list
  5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  It should be:

  Extend the 105 IP access list
  10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
  30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
  50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

  IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

  To remove it and add it to the bottom:

  105 extended IP access list

  not 5

  IP 172.19.194.0 allow 60 0.0.0.255 any

  Then ' delete ip nat trans. "

  and it should work now.

• Difference between 'Reload' and "Reload (Override Cache)"?

  Https://support.mozilla.org/en-US/kb/keyboard-shortcuts-perform-firefox-tasks-quickly#w_navigation, what is the difference between 'Reload' and "Reload (Override Cache)"? What makes "ignore cache"?

  Reloading Web pages and cache bypass aims to obtain a new copy of perhaps obsolete or damaged files currently stored in the disk cache.
  You can do it like the first attempt if a normal charging does not seem to provide a version of a Web site or if you are having problems with a Web site otherwise.

  We usually have advice that if you have questions:

  Reload Web pages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  Clear the cache and delete cookies only from Web sites that cause problems.
  "Clear the Cache":

  • Firefox/tools > Options > advanced > network > content caching Web: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Firefox/tools > Options > privacy > "Use the custom settings for history" > Cookies: "show the Cookies".

  Start Firefox in Safe Mode to check if an extension or theme (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problems.

  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• What happened between Firefox and Roboform? FF no longer mentions RF in its modules!

  What happened between Firefox and Roboform? FF no longer mentions RF in one of its modules.

  I'm having the same problem. RoboForm contacted and they act like they have no idea there is a problem.

• Parachute does not not between iOS and Mac devices... Does anyone have a good solution for it nor a lot of garbage to support

  Parachute does not not between iOS and Mac devices... Does anyone have a good solution for it nor a lot of garbage to support

  You want the solution? Why not tell us what Mac and Apple, mobile devices you have the OS and version?

  Also what troubleshooting steps you took?

  We do not have a crystal ball, and we're not sitting next to you.

• What is the best between Firefox and Aurora?

  What is the best between Firefox and Aurora?

  Hello DarshanK, that depends on what type of user you are probably: https://www.mozilla.org/firefox/channel/

• is there a difference between 38 and 42mm with their pixel density?

  is there a difference between 38 and 42mm with their pixel density? the 38mm and 42mm watches have same interns?

  You can see the technical details of the Apple Watch here. Apple - Support - technical specifications

• What is the difference (if any) between iPhoto and iPhoto library? I managed to delete my pictures in freeing up space, but have a backup available. Do I have to download these two files in the pictures folder is one duplicate of the other?

  What is the difference (if any) between iPhoto and iPhoto library? I managed to delete my pictures in freeing up space, but have a backup available. I need to restore these two files in the folder images or one is one duplicate of the other?

  I use a MacBook Air 2013 model with a backup on a WD MyBook Duo disc for storage wireless as the Apple Time Machine.

  The Photos and the iPhoto library are totally separated - neither one is connected to the other somehow--you want to restore the library you need

  LN