System gives a code 19 because it cannot recognize the F: of CD/DVD-ROM drive

Similar Questions

• my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

  my computer does not recognize the Device Manager cd/dvd/rom drive says corrupted or missing code 39

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• Error: This device does not work properly because Windows cannot load the...

  I get this error message "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) "via a wired connection. And that's the Microsoft 6to4 adapt #7 and the same card but the #4 one.  Are these drivers or another file that I could use DL?

  Hi JasonBedgood,

  1. Once you get the error message?
  2. did you of recent changes on the computer?

  This error occurs if the required driver is not installed or the driver is damaged.

  I suggest that you update the driver for the device and check.

  How can I update the driver for network card on the computer

  1. click on Start, click Control Panel, and then double-click System.
  2. click the tab hardware , and then click Device Manager.
  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click continue.
  3. click on network adapters to expand.
  4. under network adapters, double-click the entry for Microsoft 6to4and then click driver .
  5. click on Update driver software.
  6. follow the Wizard update software driver to update the driver for NICs .

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the device driver update did not help then check the link below for one of the thread with the question and try the steps mentioned by Lionel Chen on January 9, 2008
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot install Nero 10 Multimedia Suite Platinum HD because it cannot find the following files: VC Redist 2005 KB973544 (x 86)

  Original title: getting specific files

  I try to install Nero 10 Multimedia Suite Platinum HD, but it will not be installed because it cannot find the following files: VC Redist 2005 KB973544 (x 86)

  VC Redist 2008 SP1 (x 86) Direct 3D 9 Extensions 9.19.949.46 9.19.949.1104 9.24.950.2656 9.27.952.3001 Direct 3D 9.27.952.3022 HLSL compiler

  Reboot Validator

  My system is XP SP3 2 Gig of ram and all updates are underway.

  Hi DJ Wilfred.
   
  Download the stand-alone package of these updates and install it manually and check to see if it helps to fix the problem:
  Microsoft Visual C++ 2005 Service Pack 1 Redistributable Package ATL Security Update
  Microsoft Visual C++ 2008 SP1 Redistributable Package (x 86)
   
  In addition, refer to this article:
  Description of the update of security for Microsoft Visual C++ 2005 Service Pack 1 Redistributable Package: July 28, 2009

• While booting XP machine, get error "the application cannot continue because it cannot find the uncdms.dll file.

  just after the start of the desktop windows appears and then I get the error message "the application cannot continue because it cannot find the uncdms.dll file" I searched using windows search, nothing helps.

  Hello

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed on the computer?

  Uncdms.dll file is associated with the Application of desktop search in Windows that is used to find and view an overview of the different types of files, such as documents, e-mail, photos and music files on a computer.

  By default, the uncdms.dll file is located in the folder C:\Windows\System32. The file is more common in 143 872 bytes.

  Follow the methods below

  Method 1:

  To uninstall the Windows Desktop Search from your computer, you must complete the following two tasks:

  Step 1: Remove Windows Desktop Search from the boot sequence

  To do this, follow the steps below:

  a. click on the start menu, click Run.

  (b) in the Open box, type msconfig and press ENTER.

  c. in the System Configuration Utility dialog box, click the Startup tab.

  d. search and clear the check box for any option that is related to Windows Desktop Search or uncdms.dll.

  e. restart your computer.

  Step 2: Uninstall Windows Desktop Search applications

  To uninstall the Windows Desktop Search using the Add / Remove Programs, perform the following steps:

  a. click the start menu and select Control Panel utility.

  b. double-click the icon Add / Remove programs.

  c. in the Add / Remove Programs, locate and select the Windows Desktop Search.

  d. press the button Delete.

  e. restart your computer.

  Method 2:

  Run the verification and virus scan online if any malware or virus detected on the computer activity. You can run the scan for viruses online from the link below: http://www.microsoft.com/security/scanner/en-us/default.aspx

  NOTE: Make sure that you select the correct version of the operating system before downloading the scanner)

• The CD-ROM/DVD-ROM driver cannot be loaded by Windows and can be corrupted (Code 39).

  My DVD/CD driver drive HL-DT-ST DVDRAM GSA-T20N ATA Device cannot be loaded by Windows and can be corrupted (Code 39). How can I get the original device installed new driver if the CD/DVD drive does not work? It is available for download? Should it be first uninstalled and re - installed? A relative novice can handle?

  Hello

  Have you made changes on the computer before this problem?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Update the driver for the CD/DVD drive and check if that helps.

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Run the fixit for the following Microsoft Fixit and if it helps.

  Your CD or DVD drive cannot read or write media:

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Method 3:

  Uninstall and reinstall the CD/DVD driver and check if it helps.

  Follow the steps to uninstall and re-install the drivers.

  a. click on start toreduce this includes this im and then click Control Panel.

  b. click system and Maintenance, click Systemand then click on Device Manager.
  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  Reduce this includes this imageIf you are prompted for an administrator password or a confirmation, type the password, or click allow.

  c. in the Manager device, expand CD-ROM/DVD-ROM drives, right click on CD and DVD devices and then click Uninstall.

  d. When you are prompted to confirm that you want to remove the device, click OK.

  e. restart the computer.

  Hope the information is useful.

• I just upgraded to window 7 for windows does not start Lightroom 10 6 because it cannot open the catalog or one of my backups

  I just upgraded to window 7 for windows 10. 6 Lightroom does not start because it cannot open the catalog or one of my backups

  Yes, once the user account is the upgrade to windows 10 have permission on the folder of photo issue, which prevents the Lightroom to create the necessary temp file when the catalog is launched.

  This is the reason why I asked to copy the catalog file to another location to narrow down the reason for the problem.

  Thank you

• I have the latest downloadable version of the LR5.  It crashed while it was perceived 1:1 uttered during an import. After a restart of the Win764(), it displays a message that LR has to leave because he cannot read the preview files and it will try to fix

  I have the latest downloadable version of the LR5.  It crashed while it was perceived 1:1 uttered during an import. After a restart of the Win764(), it shows a message that LR has to leave because he cannot read the preview files and it will try to fix it the next time's lance.  I get the same message to another and whenever he throws so I can't launch LR at all now.

  I get the preview of a file has been corrupted somehow.  Is it possible to fix this without having to build a new catalog?

  Use Windows Explorer to open the folder containing your catalog. You will see a folder with the extension .lrdata. You must remove this folder, and then restart the Lightroom. Lightroom will generate a new folder of previews.