System recovery does not work?

Similar Questions

• Equium - dead after hibernation, the system recovery does not work

  Hello
  I'm trying to fix the laptop of one of my friends, but so far without success. It's a Toshiba Satellite with Vista.

  She had problems with a black screen after startup in Windows Vista. I found a work around for this problem, but it was a little complicated for her... She doesn't know much about computers. ;)
  So I but it would be a good idea to tell him to always use hibernation. However, when I put the portable standby extended, all seemed fine, shutdown, power off.
  I tried and then turn it back on. Light turns green, cd drive makes noises. Nothing more. Screen remains completely black. No sounds. Keyboard input does not work. No access to the Manager startup or anything else. He left light until I pass him by pressing the button for a few seconds.
  I removed the battery and put back in place, without result.
  Connection to an external monitor shows no results.
  When I put the original CD recovery Toshiba, no results.

  So, basically a cell phone dead. Ah yes, I'm in the Brazil in a small village, away from the stores of tech support or computer. Maybe a problem material, but all was working fine until I used the hibernation.

  Any help or ideas would be very appreciated! ;)
  Daniel

  Hello

  My laptop could not wake up after hibernation too but I managed to wake up again.
  This;
  Disconnect the power adapter and remove the battery.
  Now, you will have to wait a while 1 hour should be sufficient, but you can leave the laptop disconnected for a longer time (all night long)

  After that, you must connect the battery and AC adapter and should try to light the device if it will not help you then you are in trouble
  This would mean that a serious hardware problem causing this problem and I doubt you could remedy without any help from the ASP.

• My system recovery does not work

  Hello
  I have an e-machine computer with windows xp. I want to recovery s sytem to completely wipe my computer and bring him back to the original configuration. When I put my cd/dvd for system recovery, all right after that I restart until it comes to the loading screen for the recovery of the PC Angel system. After that it is trying to load the computer ends by crashes and I can't start the recovery of the system.

  WHAT DO!

  Thank you

  http://www.Microsoft.com/windowsxp/expertzone/newsgroups/reader.mspx?DG=Microsoft.public.WindowsXP.General

  Link above is to the XP newsgroups.

  There is a list of groups of discussion XP to the bottom of the left column.

  http://www.eMachines.com/support/product_support.html

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• System repair & Recovery does not work / Vista Windows Mail won't open attachments sent with PowerPoint Slide Show

  System repair & recovery does not work.  When I use it, it never restarts the computer.  I have left running and went to bed and is still running the next morning.  The SR & R is grayed out and will not open.   When I restart the computer after that it ran all night, a message appears to tell me that I cancelled the operation.  Help!

  I have another problem with Vista Windows Mail; I can't open attachments are sent using Microsoft PowerPoint Slide Show.  The message is: * this file does not have a program associated with it for performing this action.  Create an association in the set Associations Panel.  I don't know anything about computers or the control panel.  How can I fix these problems?  Help!

  Problem with recovery to factory settings or system/process of repair software, contact the manufacturer of your computer.
  It is their software/recovery process, not Microsoft.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You need PowerPoint or a viewer PowerPoint installed on your computer to read PowerPoint attachments.
  Learn about file Associations in the lower part of this response.

  need .doc or .docx Word or a Word Viewer for playback file extensions, etc, etc.
  .xls Excel need.
  need for .pps PowerPoint

  Here are the download links for free Microsoft Word, Excel and PowerPoint viewers:

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=3657ce88-7cfa-457a-9aec-f4f827f20cac&displaylang=en

  Word Viewer

  View, print and copy Word documents, even if you don't have Word installed. This download is a replacement for Word Viewer 2003 and all previous Word Viewer versions.

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=1CD6ACF9-CE06-4E1C-8DCF-F33F669DBC3A&displaylang=en

  Excel Viewer

  Open, view, and print Excel workbooks, even if you don't have Excel installed. This download is a replacement for Excel Viewer 97 and all previous Excel Viewer versions.

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=048dc840-14e1-467D-8dca-19d2a8fd7485&displaylang=en

  PowerPoint 2007 Viewer

  Microsoft Office PowerPoint 2007 Viewer allows you to view the presentations of all the features created in PowerPoint 97 and later versions.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  And here is a link to a set of free office of Applications:

  http://www.OpenOffice.org/

  And to set file Associations:

  http://articles.TechRepublic.com.com/5100-10878_11-6172036.html

  How do I... Change file extension associations in Windows Vista?

  See you soon.

  Mick Murphy - Microsoft partner

• Windows 7 upgrade failed - disk HARD recovery does not work

  I just received my Windows 7 upgrade disc, followed the procedure and he managed to upgrade Vista 64 bit for Windows 7 32 bit! Some drivers also seem to, were charged more than once.

  I tried to do a system restore from the recovery of HARD drive partition - and it won't!

  Can someone, please?

  Hello

  Drive HARD recovery does not work because Win 7 ran the Boot Manager and maybe the HDD partition has been affected.

  I guess you want to roll back to Vista preinstalled Toshiba.
  I think in your case, only the recovery disc will help you.

  Welcome them

• Envy of HP dv7-7332ea - System Restore does not work on windows 8

  Hey there,

  I recently bought this machine about a month ago. I used the Windows 8 System Restore feature to restore my pc to a previous state.

  However, after running it, I got a message saying: it failed and to ensure my anti virus is disabled. Accordingly, I have disabled Norton and tried again but it still does not work.

  Previously, the only problem I had with the pc was that he locked himself completely and therefore I turned off the machine that I have been unable to close.

  When I rebooted, HP Support Assistant could not run and so I uninstalled and then reinstalled from website theHP. It is now resolved. The thing is I'm a little scared that something is wrong with the machine that is the reason why I think that the system restore does not work.

  I'm a newbie on the computers here. Could you please give me some advice to diagnose if there is nothing wrong with my machine and fix the system restore?

  See you soon,.

  Damon

  Hi Damon,

  Norton is a component called 'Tamper Protection' that should be disabled before a system restore can be performed - for more details on this topic, see the following link.

  Disable self-protection.

  Kind regards

  DP - K

• System Restore does not work, once again.

  Hi, I read a topic of 2010 that has not yet been answered. I worked with a tech at Microsoft by e-mail, but when I answered: System Restore didn't work. Now it does not work yet. I had installed Returnil system safe, but I got an error msg 0 x 80004005, (third-party antivirus), so I uninstalled the program. I went through the registry and delete something with Returnil all 4 sections of the registry. Remove the common files folder that was left after uninstalling. Restarted my computer several times. I use MSE, with free versions of spywareblaster and MBAB, who are both at the request not in real time. I tried to restore to a time before I had installed Returnil first, (I installed and uninstalled 3 times in 2 days) and could not. I tried to use a snapshot to restore spywareblaster and managed to restore to the point 2 x before installing because forward the installation of point returnil has been altered. At the moment no malware has been detected and no threat of MSE. What to do next?

  Thanks in advance for any help. Liz.

  Here's my usual route to find out how to reinstall System Restore:

  If you have already run MBAM and SAS, temporarily disabled your antivirus and anti-malware applications and tried your Safe Mode system restore and you still get the restoration of the system to work, you must reinstall just your system restore.  You do not have to reinstall XP - just reinstall the system restore part.

  System Restore is a frequent target of attacks by malicious software.

  When you reinstall the system restore, all your current Restore Points will be deleted and you must restart your computer once the installation is complete.  After the reboot, a new Restore Point will be created as a new point of system control in your calendar of SR.

  If your system had a malware infection, it could be that some of the files in your old Restore Points are also infected up to wipe out the 'old' and new is often a good idea if you wonder if the old Restore Points are infected or not.

  Assuming that your XP is installed on drive C of your computer:

  As you go through the reinstallation of the RS, the resettlement will be asked to locate certain files as you go along and ask your XP installation CD.   If you do not have a genuine XP bootable installation CD, you can change the path where Setup looks for files one at a time, because they are needed.  More on that later.

  Navigate to the following folder:

  c:\Windows\Inf

  Locate and right-click the following file:

  SR.inf

  Choose Install

  If you can not see the sr.inf file, set up your system to show hidden files and show file extensions.

  Click on tools, Options, view and turn on "Show the hidden files and folders" and uncheck "Hide extensions for known file types", then you should be able to see the file c:\windows\inf\sr.inf.

  Installation can request files from the c:\windows\inf\386 folder.  It would be your installation CD bootable XP genuine if you have one and the Service Pack installed on your system must be the same as the CD that you will use.

  You don't need absolutely a CD to do the reinstall, because files must already be on your system somewhere if SR was working before.

  If you are prompted for a file, and you can't find it where I suggest in my example below (it works on my system), you need to search your hard drive and find where the files on your system.

  If the request to a file and you don't know where he is, let waiting for installation and click Start, search, and search for it
  has requested the file and find it on your system.  If SR has already worked before, the file is already on your system somewhere.

  Search finds the requested file, go back to the installation and specify the path where you found the file requested and click OK.  Installation can request several files along the way, but you can find them all.

  Here's how my system works when I reinstall SR when I pretend that I don't have a genuine XP bootable installation CD:

  When you are asked:

  SR.sys

  Point the install in c:\windows\system32\drivers

  When you are asked:

  c:\windows\system32\srclient.dll

  Point install it in c:\windows\system32

  When you are asked:

  Filelist. XML

  Point of installation at c:\windows\system32\restore (or c:\windows\ServicePackFiles\i386)

  When you are asked:

  srframe. MMF

  Point installation c:\windows\system32\dllcache (c:\windows\system32\restore)

  Once installation is complete, you will receive a message that you must restart your computer.

  Restart your computer and look at your schedule of SR.  You should have a new point system control in your calendar.

  When you get SR working again, I ran MBAM and SAS to make sure that your system is reasonably clean of malware.

  The day that you think you need to help the system restore you is not the day to discover the system restore does not work, then you need to test.

  After the reinstallation, manually create a Restore Point and test the restoration process and make sure that you are convinced that it works from one end to the other.

• Helpctr.exe does not load in the Start Menu. System Restore does not work.

  Help and Support not be loading not on the Start Menu. I get a msg of error helpctr.exe is not found. I run for the file with no result. Also the system restore does not work even in safe mode. I use XP Home SP3. Any suggestions? Thank you.

  No problemo!

• My system restore does not work even in safe mode and I can't download anything.

  Original title: Hi, one day I turned on my pc. Then, I realize that system restore does not work even in safe mode. I can't download anything. And the windows installer does not work.

  There was nothing but my background, then after 2 minutes my desktop icons appeared. But no start bar. Then, I realize that system restore does not work even in safe mode. I can't download anything. And the windows installer does not work. Help! PLeeease.

  Hello

  1. have you made changes on the computer recently?

  Method 1.
  Let us firstly the sfc scan and check if there is any missing system file.
  Reference:
  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
  http://support.Microsoft.com/kb/310747

  Method 2.
  Try the methods listed in the articles below and check.

  Steps of troubleshooting for problems when you try to use the System Restore tool in Windows XP
  http://support.Microsoft.com/kb/

  Method 3.
  Re-enter the Setup engine
  a. Click Start, click Accessories and then click command prompt.
  b. at the command prompt, type the following and press ENTER after each line:

   
  MSIExec /Unregister
   
  MSIExec/regserver

  Method 4.
  If the problem persists, then create a new user profile and then copy your current users assigning to this profile. For more information, see:
  How to create and configure user accounts in Windows XP
  http://support.Microsoft.com/kb/279783

  How to copy data from a corrupted to a new profile in Windows XP user profile
  http://support.Microsoft.com/kb/811151

  How to recover damaged Windows XP user profile
  http://support.Microsoft.com/kb/555473

  I hope this helps.

• System Restore does not work completely. Virus problem?

  When the System Restore dialog box asks me when I want to restore from I can not pass separating two to another. The instructions are to click on a date "BOLD", but most of the dates are "BOLD", (b) none of them are clickable outside today and (c) the back arrows for the previous month, while only clickable, do nothing.

  I think I have a virus or somesuch and wants to do a restore. Maybe the virus of going to stop.

  WXP SP3 Prof

  Viruses often attack the system restore because it's such a threat to them - which is certainly possible.  Unfortunately, all my anti-virus, anti-malware and anti-spyware solutions are for Vista (which is the Forum, you are in).  You must post this question in the appropriate forum where they have the information, procedures and links to help you.

  One thing, if the system restore does not work in normal mode, it sometimes will run in Mode safe then start safe mode and try it.

  In addition, if you use any Norton product, turn it off, then restart and try to restore again - Norton is known to cause problems with system restore.

  Sometimes, the problem can be solved by turning the restoration of the system off and then back on.  Unfortunately, a side effect of this is to lose all your restore points you want to restore this may not be such a good option to try (even if it can correct the underlying problem): http://support.microsoft.com/kb/310405/en-us.

  If none of the above works, please repost your question on the Forums of XP to: http://social.answers.microsoft.com/Forums/en-US/category/windowsxp where the XP experts will be happy to help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• my system restore does not work, nothing is changed

  I have vista home premium and my system restore does not work no matter how, I try

  Hello

  There are a variety of reasons for system restore problems

  Norton and Norton product Tamper Protection is the main

  Read about it:

  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20101101224849EN&LN=en_US

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  You can try restoring the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  and malware can interfere with the restoration of the system

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."

  Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."  How can this be repaired?

  Hi rebick,.

  Try the troubleshooting steps presented by spirit X in this thread.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unexpected error in the property page. The VSS service uses the system restore does not work. Error (0 x 810000202). __

  original title: "there was an unexpected error in the property page. The VSS service uses the system restore does not work. For more information, see the journal of events (0 x 810000202). __

  "There was an unexpected error in the property page. The VSS service uses the system restore does not work. For more information see log of events (0 x 810000202).

  Please try the troubleshooting below to check the status of the shadow copy Volume service

  1. click on start > all programs > Accessories > run

  Type the following text in the run window, and then click ok:

  Services.msc

  You will get the Services window.

  2. Please check service Volume shadow copy service is "started" and "automatic".

  If these services are not set to "Started" and "Automatic", please, do a right-click on the service and select "Properties".
  On the window properties, please change the startup type to automatic, and use the Start button to start the service.

  Click on apply, click ok.

  Close the Services window

  Restart the computer and check if the problem occurs again.

  If the problem persists, start your computer in safe mode and try to do a restore of the system again. Temporarily disable your anti-virus protection

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  I hope this helps
  If this post can help solve your problem, please click the 'Mark as answer"If you find it useful, mark it as useful by clicking the 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Vista System Restore does not work. I disable Norton Antivirus before you start the process. What can I do else?

  Vista System Restore does not work. I disable Norton Antivirus before you start the process. What can I do else?

  1. try SR in safe mode:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  2 Malware will stop at the system restore:

  If necessary, do all the work Safe Mode with network.

   

  To get into Safe Mode with network, press F8 at the Power On / boot and use key arrow upward to get into SafeMode with networking from the list of options, and then press ENTER.

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight.

  See you soon.

  Mick Murphy - Microsoft partner

• System Restore does not work on my Windows 7 computer

  System Restore does not work for me on Windows 7 pro, he returns with a cancellation but does not either.  I have load a movie in movie maker and all the trouble started.  I couldn't finish the loading of the movie at that point, I started to have problems with the operation of windows.  End result, I tried restoring the system without success...

  Hello

  1 are you getting any error code or error message?

  2. have you successfullyperform before system restore?

  3. have you made any change before this problem?

  I would suggest trying the following steps and check if it helps.

  Step 1: search for errors in the event viewer.

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Step 2: check if you are able to save the clean boot.

  Note: Please make sure that the computer is configured to start as usual by following step 7 of article.

  Step 3: security software temporarily disable and check if it helps.

  Disable the anti-virus software in Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: After reviewing the matter, must reactivate the security on your computer program

  Also refer to:

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Sebastian M

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.