T400 and 3g modem

Similar Questions

• Problem with T400 and external monitor (1920 x 1200 resolution)

  Hello

  My laptop:

  ThinkPad T400 2767-C99 * (graphics: ATI Mobility Radeon HD 3470 256 MB / X4500MHD (Switchable Graphics)), OS is Windows XP

  I just installed the latest video driver from lenovo page (which also installs "ATI catalyst")

  Externale monitor:

  I just bought a Samsung SyncMaster 2443FW, 24 "TFT monitor with a maximum resolution of 1920 x 1200

  Problem:

  Monitor works fine with my new T400s and my old Acer laptop. However, with my T400 (described above), I can't do the monitor uses the 1920 x 1200 resolution. However, all the other ugly resolutions so I need it to work with 1920 x 120

  -If I change the resolution of right on the desktop of Windows XP (and then properties-online settings) and set the screen on 1920 x 1200 resolution, then my monitor used only a lower meanless (1440 x 900) and effect of scrolling as I move my pointer on the screen

  -If I use the ATI catalyst software to set the resolution, I can only chose smaller resolutions (he not go 1920 x 1200)

  Questions

  Is it a hardware (maybe the graphics card does not support 1920 x 1200) or a software problem (maybe a problem with the driver) or just a matter of adjustment?

  What can I do?

  Help would be much appreciated!

  * Original description: 2767-2JG base: T9550(2.66GHz), 4 GB of RAM, HD 250 GB at 5400 RPM, 14.1 LCD in 1440 x 900, 256 MB ATI Radeon 3470HD, CD-RW/DVD-RW, Intel 802.11agn wireless, Bluetooth, Modem, 1 GB ether, UltraNav, chip dry, RPF, camera, 9 c Li - ion, BACK license

  Problem solved:

  I was using my old monitor vga cable that doesn't use 14 pins (worked fine with my T400s and Acer laptop - but not with the T400).

  => When I switched to cable 15-pin that came with the monitor, the problem was gone!

• My speed has decreased between the router and the modem is not working properly, what can I do to increase the download speed with my Time Capsule 802.11n

  My speed has decreased between the router and the modem is not working properly, what can I do to increase the download speed with my Time Capsule 802.11n

  A variety of phenomena can affect the performance of its wireless network. You may be able to mitigate some negative effects.

  Solutions to any factors that may have an impact on your wireless network, read use the Diagnostics wireless for you help to solve the problems of Wi-Fi on your Mac - Apple Support.

• Service (search) and N ° imei and empty Modem firmware

  Hello world.
  I use the iPhone 6 more. This morning, I used like normal, but he has a problem while I'm closing 4G data it shows not the search in the bar service.
  I tried to restart the phone with Home & power button, also I tried to reset the setting also but it stays the same. I was getting ready to restore in iTunes but when I check the imei number, it's no imei in the list and Modem Firmware is empty. But the phone still as usual as the Wifi and the application that it no service does not (research).

  My question:

  1. How can I retrieve the Imei and the Modem Firmware number and use it as usual?
  2. now my phone it works always, what will happen if I try to restore or upgrade to new iOS in iTunes?

  Please help me solve this problem. I really really sad and don't know what to do now! also, I have no money to change :-(

  Hello

  If your SIM card has been blocked, check with your network provider?

  See you soon

  Brian

• Sound problems and the modem EA60-155

  3 weeks ago I received my laptop EA60-155 and have experienced ongoing problems with the sound and modem on the laptop. I bought the laptop from currys so am sure that they are an authorized dealer.

  The problem is different, sometimes I turn on the laptop to find out, there is no sond and the modem does not work, sometimes the sound works and makes the modem for about 15 minutes before the problem arises again. I bought the machine to the dealer authorized to Bahrain twice now, twice they said them that the problem was resolved when he doesn't. I called the center of appeal twice, but I still have the problem. Any advice would be greatly appretiated.

  Hello

  If you have this problem permanently, you can try to reinstall the modem and sound card. If the unit is pre-installed with recovery DVDs, it should work fine. As a first step, you can try and remove the sound card and the modem from Device Manager, then restart the device. The two hardware components must be recognized and installed again.

  If there is no success I recommend you backup your data and reinstall the OS using recovery DVDs. On this way the unit will be clean installed and there should not be any problem. Every problem that happens after that can be some hardware malfunction and you must contact the Service partner again.

  Good luck!

• Qosmio F10 - driver of sound and the modem does not install

  Hi all.

  Firstly, my computer is 100% up-to-date. I recently had to do a complete reinstall of my OS
  I got all my drivers and what not, install, but the driver sound max and the modem driver will not install.

  For the modem, it asks if I want to install it, I click Yes and it starts the installation and then he finshes and nothing comes. It is not installed.
  I then try my sound, and it seems as if it will install, but then I get an error that says: no driver is found, please reboot your computer.

  Or something around those lines anyway.

  Can someone help me please?

  Hi, have u tried in safe mode. Why do not you download the latest drivers? You can try this site http://driverscollection.com/?H=Qosmio%20F10&By=Toshiba

• T400 and Advanced mini dock

  Hi - I have a T400 with integrated graphics card and I'm looking into getting a mini dock advanced to run an external monitor.

  What output resolution has done with success through the advanced mini dock VGA port? -This will help me understand which monitor to get, I read that many had bad signal of the dock when using the VGA port.

  As my T400's only integrated graphics, I won't be able to use the port DVI - is this still true or something changed?

  Your comments would be much appreciated,

  Thank you

  Cosmin

  Hi cosma12,

  Your T400 with integrated graphics can digital video output through integrated DisplayPort or DVI connector on the advanced Mini dock. It is only the switchable T400 graph that cannot use DVI with integrated graphics card, they must use the ATI chip instead.

  Graphics from Intel in the T400 can drive 1920 x 1200 on DVI or DisplayPort - which I think is the highest resolution, supported by the single-link DVI. If you are shopping for monitors, I highly recommend to make one with a digital input: DVI / HDMI / DisplayPort. the video quality is theoretically (and practically) better than when using analog (VGA).

  EDIT: Oops, the T400 (and R400) do NOT have the DisplayPort, while the largest do T500/R500. My bad.

• I have a wireless printer and changed modems and need to know where to go and change the security key to make it work wireless

  I have a wireless printer and changed modems and need to know where to go to change the security key for the printer works wirelessly.

  I have a wireless printer and changed modems and need to know where to go to change the security key for the printer works wirelessly.

  The method depends on the printer. Read the instructions or uninstall, and then reinstall the printer. It will ask you the modem settings.

• Airport Extreme and Broadband Modem/Router

  I have my Airport Extreme (5th generation) plugged into a Broadband Modem/Router combo. I would like to have both able to use their wireless capabilities. The Airport Extreme has been previously connected to a Modem broadband all my IP addresses came by Airport Extreme (192.168.2. *). With the New Modem/Router combo broadband, it uses 10.0.0 * so I would be able to use Airport Extreme to add the 192.168.2. * While having the 10.0.0. * the Broadband Modem/Router combo.

  Is this possible and, if so, how do I configure Airport Extreme to do?

  Normally, you don't want two devices on the same network as the two try to act as routers to the same network. Which will produce conflicts of IP addresses... which can possibly be addressed... and a Double NAT problem, which cannot.

  The Double NAT error can cause a number of unpredictable issues... things like the problems of communication between the devices on the network, slow navigation... or, not navigation in the case of certain websites, Internet access slower, to name a few.

  Yes, some users may get away with a Double NAT on a single home network, but unnecessarily complicating things over a network is normally something you want to avoid.

  We do not recommend it, but if you really want AirPort Extreme for use range 192.168.2.x however, you can easily make this change using AirPort Utility. If you are not sure how to do this and need help, then we will need to know which version of AirPort utility you are using.

  To find, open AirPort Utility, and then click the menu of AirPort Utility in the far left of the screen corner. Click on about AirPort Utility to see what version you have and post back with that info.

• Time Capsule do not pick up address DHCP and cable modem...

  You just bought a Time Capsule and a couple of Airport Express. If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  That being said, I tried to create a mobile network instead of pure wi - fi and am studying various behaviors that are not as expected when I rear hub to the Internet Time Capsule, but need to isolate and go 1 bit at a time... (it works not as well as suggest Apple instructions on homelessness of installation)...

  If:

  1. configuration of the modem cable shows that DHCP is 'ON' and supplied address range 192.168.0.x by 192.168.0.y,.

  2 Cable modem wireless is disabled,

  3 Time Capsule Wan is connected to the cable modem, Ethernet

  4 Time Capsule is configured to request its address IP, DHCP

  5. Airport Express is in Bridge mode and have addresses such as 10.x.y.z (appears to be from a Time capsule).

  6. safe as Time Capsule is set to be as DHCP and NAT

  7. There is NO other device in this configuration connected by Ethernet except the cable Modem and the Time Capsule.

  So, why is the IP address of the time Capsule 76.181.45.xyz? (The address is NOT in the range of the DHCP as described in the #1; it is not supposed to be?) ....

  Whence this address?

  A friend says this address puts the "other side" Time Capsule of the cable Modem, directly on the Net?... (Shouldn't worry?) ....

  If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  It's because you didn't have the devices connected via Ethernet before you set up the. Given that the installation utility saw a wireless connection, it is assumed that this was the way that you want to connect devices on your network at all times... so he put it this way.

  If you had an established connection Ethernet before you ran the installer, then the utility would have detected this connection and set up the airport to "expand using Ethernet", does not extend to assistance of wireless.

  (it works not as well as suggest Apple instructions on homelessness of installation)...

  If all goes well, you don't talk about this document... Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo... .. Since the 'how' information in this article is at least 4 years late, bear little resemblance to the latest version of AirPort Utility and some of the information are simply not true.  This document if trash is what you... He'll probably do more harm than good with regard to the details of setting.  The article is OK for basic general information, however.

  6. safe as Time Capsule is set to be as DHCP and NAT

  It should not be if your modem is a modem/router "" or type 'bridge' of the device which is also DHCP and NAT services. The fact that you have disabled the wireless on the device confirms that it is both a modem AND a router. That being the case, then you have two devices that both struggling among themselves to try to control the same network... AND do you also have a network error called Double NAT... something you don't want.

  Probably the best at everything again and provide us with the number of brand and model of your "modem", that we can confirm what it is that you have, then the correctly configured time Capsule to work with this device. Once the time Capsule is set up correctly, it will be easy to put in place the other airports.

• Problems with AirPort Extreme and Qwest Modem/Router.

  I have a Qwest ActionTec 1000 DSL VDSL2 gateway and want to disable the functions of router wireless and those through direct AirPort Extreme. I know that in the Modem I have to disable the functions of addressing and turn them in the AirPort Extreme to avoid address conflicts, but what are the settings I need to change in both devices? And what is "A Transparent bridging" on the side of the modem?

  But what are the settings I need to change in both devices?

  Sorry, we can't help on the settings for the modem/router, because it would be a question of Qwest as to if this is even possible and if so, if Qwest will support this type of installation. Sometimes the ISP lock modem/router settings, and although it seems as if you can change the basic configuration of the unit, you can really.

  Yes, it is possible that another user of Qwest has done with the same modem/router you have and an AirPort Extreme... and may know the answer... but the chances of the person who holds this information also to see this post are slightly above zero. But, I guess it's possible.

  If the modem/router can be configured to operate only as a simple modem, then the next step would be to get your Mac connected directly to the modem to test the connection in this way. If Qwest is going to help you, they will do it no doubt with your Mac connected directly to the "modem" as well.

  Once you know the exact details of the PPPoE authentication to establish a connection, these parameters can be transferred to the AirPort Extreme and removed from your Mac. To do this, you reset the AirPort Extreme back to default and then put settings in place again. The installer should detect the PPPoE connection and then ask for your login information.  After this, the correct settings apply to AirPort Extreme during the installation.  You can still use the same wireless network name and password you used before if you wish, or set up a new network name and password.

  PPPoE on the routers of the airport, at least in my experience, was not a reliable way to connect when I tried this in the past, but you don't really know how well... or even if... it will work until try you it. Unless you really want the airport to distribute IP addresses to devices on your network, things would be a lot more simple if you went ahead and used the modem/router "such what" and then let the airport works in Bridge Mode to transfer information in connection with network devices.

  When you have the modem/router converted to act as a simple modem and made a successful connection using your Mac connected directly to the "modem", post back and we can help with the configuration of the AirPort Extreme if you need more advice.

• Linux live CD on Satellite M70 and Driver Modem

  Hi I want to use Linux Live CD (or USB boot Linux) on 70 M satellite. I tried puppy linux, but it did not recognize my modem and the USB key (I use the dial upwards). I want to know if someone has used linux live CD on this PC and he was able to use the dial-up modem. To this end, if I need a driver (linmodem), which one and where I should get. And what live CD distro I should choose.

  Preference, I like any distribution that can be started from a USB because I n, t want to use my HD at all and boot USB will give me the opportunity to saev my job back in the USB. I only use the Internet (dial-up modem) and word documents (OpenOffice or other), or maybe (not required) I like to watch movies (CD or DVD).

  Thank you.

  Hello

  Try again with the Knoppix Live CD. I didn't try yet but I will do in the future. Get info on http://www.knoppix.org/

  By the way: If you want to use other BONES because of security or do some experiments, you can also try installing the virtual machine. A few days ago, I installed VMware Workstation. There, you can preinstall a few different operating systems and do what you want (Internet and so on).

• Portege R500 and Novatel Modem 3G on Windows 7

  Hello

  someone have a solution for getting the Modem 3 G build-in novatel works on Windows 7 in a Portege R500?

  I tried to install the driver for Vista 32 bit on my W7-Ultimate32bit. I have tried this driver:

  http://de.computers.Toshiba-Europe.com/innovation/Tracker.jsp?file=http%3A%2f%2fsupport1.toshiba-tro.de%2ftedd-files2%2F0%2fwmb-20071115155201.zip

  Installation starts fine, but the installer then a fallback and stops.

  What do I have to wait for a W7 driver?

  Klaus

  > Should I wait for a W7 driver?
  I think so. You can try to use the Vista driver but there is no guarantee for correct material work.
  I think that Win7 drivers will be available soon.

• Satellite Pro A120 and device modem on high definition audio bus drivers

  I did e clean install, but I have no sound.
  It takes the bus drivers modem device high definition audio. Anyone know where I can find them?

  Hello

  Have you tried to find on Toshiba support and download page under http://eu.computers.toshiba-europe.com?
  Satellite pro A120 is the old model of laptop and must be fully supported for WXP and Vista.

• HP 50 g - PC connection series with adapter Series USB and null modem troubleshooting

  I have the calculator correctly connected to my laptop via a USB series adapter, which is plugged into a null-modem adapter, which is plugged into the serial cable sold on HP Calc.org specifically for the HP 50 g. I started XModem on the calculator, but Conn4x found nothing. Is the process different from that used for USB and Conn4x connections? The problem could be with the USB Serial Driver. I use the default MicroSoft driver installed to connect? Are there tests I can run to determine if the adapter is broken, or the computer or calculator. Thank you very much in advance for your help!

  I already tried the following:

  • The two indicators relevant system are correct for the serial communication
  • Tried to reinstall the driver
  • Google for any relevant information that is extremely rare
  • Tried with two Xmodem Kermit servers running on the calculator, press 'Connect' on Conn4X.

  Hi!, Ranothil:

  If you have the following cable "null modem" (http://commerce.hpcalc.org/serialcable.php), you can transfer, all

  data, HP50G, to the PC and vice versa, throughout the connection Kit (Conn4x), without issue.

  Please, see this link, to education, to transfer data with the serial null modem and connectivity kit cable... http://sense.NET/~Egan/SKB/ or... http://www.hpmuseum.org/cgi-sys/CGIwrap/hpmuseum/archv017.cgi?read=125259

  Note: best if you transfer data, HP50G, PC and vice versa, through the microUSB.