T400s does not start after cleaning the keyboard

Similar Questions

• T400 does not start after the first display screen

  What is going on? I have wss to work today and my computer shut down due to the low batt. I got home and plugged in and waited a few minutes and turned on. When I checked swipe my fingerprint, all that I saw the first startup screen told me I want to interrupt normal off set up that I can close the button think vantage. It is stuck there. I can activate it on and but it does not start after that screen. What can I do? I am in the middle of the drafting of the report and cannot access my docs!

  I looked the problem and found that have been in contact with the usb pins! Yay the prob is fixed!

• My laptop does not start after cleaning

  Hello
  I knew an overheating problem on my laptop.
  I therefore decided to remove a processor heat sink and empty dust. It was released with processor...
  There was a huge load of dust, so I cleaned it, put new thermal paste...

  Now computer laptop does not start loading Windows.
  It checks only the CD, HARD disk, and that's it.
  Screen is blank, ON the indicator led is on.
  Two fans periodically start to turn (when they stop radiator heat - so the processor works)

  Where is the problem?

  Thank you

  Hi Dubas,
  You can access the BIOS when you try to start your laptop? This can give you a clue as to why the OS will not charge.

  Kind regards

• Computer does not start after running the utility Boot Lenovo.

  Hello
  I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
  Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
  When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
  Any idea what this problem could be? Would it be a bad power supply?
  Thank you

  Mario

  Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

  Thank you

• Black screen, high regular of underscore on the left does not start after reflashing the BIOS F.38 on HP2000-363NR

  HP2000 363NR, recently tried flashing the BIOS F.38 (here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116227-1&cc=us&dlc=&lc=en&o... ) to solve a problem of overheating.

  Well, it was a mistake.

  Now it does not start at all.

  Fans spinning upwards. Hard disk rotates.

  By pressing ESC, F1, F2, F9, F10 and F11 at startup to give appropriate (fast!) messages but then go to the same place:

  Black screen with flashing underscore in the top left. Leave it to this screen has no effect.

  Never see no text except the quick messages in the lower left (or "Press the ESC key for the system menu" down left based on nothing).

  Out and the relocation of memory does not work. Boot with a DIMM module does not work. Now hold power for one minute while the battery and plug on does not work.

  Battery is fully charged.

  OS is Windows 7 64 bit Home Premium, came with the laptop.

  Is it possible to return this BIOS?

  -Me

  Thanks to Xraytim in the post below, short-circuit the battery CMOS me returned to the previous BIOS. Need to remove card system as a whole to achieve this * beep * connector, but 34 screws later (34 = some # between 15 and 50), BIOS is back, problem solved.

  Thanks for the forum!

  -Tim

  http://h30434.www3.HP.com/T5/notebook-lockups-freezes-hangs/DV9858ca-won-t-boot-after-BIOS-update-won-t-power-with-AC/TD-p/555547

• My copy registered and checked for XP Pro SP3 does not start after changing the motherboard. Second problem is that I can't find my original install of XP Pro disc.

  After failing to find the source of reliable performance from my PC, I decided to bite the bullet and replace the motherboard, memory and the CPU. I installed a triple base 435 Athlon and a motherboard Gigabyte MA74GMT. Awarded PC again started the first time - but Windows will not, I get a number of options but none work - safe mode brings up several lines of messages on the partition of multi (0) disk (0) rdisk (0).

  A previous post suggested that a similar message meant some kind of malware but if I replace the old motherboard, processor and memory Windows works very well - in fact I use it now.

  Do I have an option but to reinstall Windows from a CD? Otherwise I have a problem - I can't find the installation discs for each piece of software except my Windows XP Pro! I do repair discs?

  Thanks for your help.

  Hi DaGeLi,

  · Provide us with the complete message you receive.

  Follow the methods below:

  Method 1:

  You were able to start the first time, you can try to boot to the last known good configuration and check the results. Link to get the procedure please refer to: how to start your computer by using last good known Windows XP Configuration:http://support.microsoft.com/kb/307852

  Method 2:

  If it doesn't then you can follow the procedure from the below mentioned link. As you do not have the Windows XP CD you can follow the procedure if you have already installed on the computer to recovery console

  How do I recover from a corrupted registry that prevents Windows XP startup:http://support.microsoft.com/kb/307545

  Otherwise, you may need to make the boot floppies. See the link for the procedure below:

  http://support.Microsoft.com/kb/310994

  You can also contact the manufacturer of the system to get the Windows XP CD.

  For reference: how to fix a computer that does not start:http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx#2

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think

• Satellite Pro S300-120 does not start after replacing the CMOS battery

  Hello

  My friends laptop - a S300-120 - was having a few problems.

  I replaced some parts about this before, including a screen crack with no problems.

  However, he began to refuse to start saying "out of battery CMOS, Press F1 to enter setup". Of course you would have to do this, set the date and time, except & restart only to get the same message. We have replaced the CMOS battery with a with the same serial number and now the laptop will not boot.

  It does one of two things.

  It is one) seems to turn, turn to the top disk & CD player, cooling fan is 100%, then flashes the POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.

  Or (b) turns on, turntable, does not turn up to cooling fan, POWER ON witness remains stable, no response from the keyboard or LCD.

  I re-assembled the laptop several times & can not find all the missing fittings or obvious signs of damage.

  The only thing I can think is that the motherboard has been damaged - somehow find replacements is delicate.

  Any ideas?

  Hello

  (> It is a) appears to turn on, turn the disk & CD player, cooling fan goes to 100% and then flashes him

  POWER ON led once, twice by orange, and then green to 1/2 second intervals, with no response from the keyboard or LCD.
  Usually, if the voltage in abnormal feeding malfunctions when IN DC will be blinking orange.

  In my opinion, it looks like a problem with the motherboard :(
  Eventually, you will need to replace the mobo ;(

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• Does not start after using the recovery Toshiba Tecra M5 - disk

  After using the restore on my Tecra M5 CD, the computer cannot even start!

  What to do in this situation?

  Hi jbdoktor,

  Does that mean exactly?
  Now, what happens if you start the computer?

  Sorry, but without this information it is difficult to help you. Maybe you should try the recovery again disk

• WINDOWS 8 PRO DOES NOT START AFTER UPGRADING THE BIOS

  ACER Aspire 4730z

  I just updated my BIOS version. And after the easy upgrade restarted my laptop. And boom. My Win8 is not start now... help me :((

  Hello

  You will need to maybe get into your bios and restore the order of boot device... You would think that would be already fixed properly, but sometimes it isn't.

• VCenter 5.1 does not start after joining the domain

  I have a VCenter Server 5.1 that I had to join the domain. The domain controller has died and I had to rebuild the domain from the ground controller. It is early in the generation of the environment and the user does not backup turns yet. The SQL database is on another virtual machine which I added to the domain and at least I think I have fixed the AD accounts on the SQL Server. I ping the SQL server machine vcenter server. I also have a Web server that uses the SQL Server and it works correctly. All thought that the web server uses a SQL account and not a Windows account. Having said that it's the VCenter error I get. I don't know where I can get more detailed logs. VCenter service dies as soon as I try to start it.

  Here's the log of events

  Application error event ID 1000

  Name of the failing application: vpxd.exe, version: 5.1.0.35539, time stamp: 0x514d6239

  Name of the failed module: vmacore.dll, version: 5.1.0.35539, time stamp: 0x514d5992

  Exception code: 0xc0000005 fault offset: 0x00000000000022f7 failed process id: 0xbd0

  Start time of application vulnerabilities: 0x01cefb39789687d1

  The failing application path: D:\Program Files\VMware\Infrastructure\VirtualCenter Server\vpxd.exe

  Path of the failing module: D:\Program Files\VMware\Infrastructure\VirtualCenter Server\vmacore.dll

  Report ID: bf5595b0-672c-11e3-958d-000c2944f450

  Just rebuilt the VCenter server, was faster than to try to fix it.

• Acer Aspire not start after cleaning the fan and re - paste.

  I need help, I cleaned up my Aspire 5750 was dust accumulated during the last 3 years, I dismounted, clean the fan, re-glued the CPU and put everything back carefully, when I turned on it, the rotations of the fan for a while, then turns off, gets battery (change from orange to blue) but black screen only. What is the fried MB? Please give me some help here.

  I have checked the connections, changed the battery CMOS, tried pressing the power button / stop without the battery and the network for 20 sec.

  Thanks in advance.

  Ironfly. thanks for the suggestion, but I solved the problem by inserting a small file of Scotch (2mm thick) between Mo and the top cover, I got the idea from another post of member's (royrempel) in another thread in this forum found here:http://community.acer.com/t5/Notebooks-Netbooks/Acer-Aspire-5552G-power-light-but-only-a-black-scree...

  Thanks for the reply, it is still very useful when we panic and start looking for a new MB

• Does not start after replacing the cmos battery

  HP m8430f, Vista Home Premium.  Worked very well but sometimes had to restart using "pulsed" F10 (5 seconds) then wait 5 seconds, and then F5, then ENTER, F10, then ENTER.

  I suspected the CMOS battery, so I removed it.  He tested "fair."  Got a new CR2032.  He attached the test counter, so it's okay  "I WAITED ALL NIGHT BEFORE REPLACING.  But the computer does not restart.  I went through the steps above and still no luck.  What to do next?  Thank you, Joe

  FIXED!  I removed the battery (I had to remove the sound card to get in the first place to the battery).  I waved it around a little when you reinstall.  Now it's working.  What I've done, I have no idea, but it works now.  Sorry for the post, but I was desperate.  Joe

• VCenter Service does not start after changing the port number

  Hi all

  Accidentally, I changed the port number for the Vcenter server from the portal of VCenter 10443 and dint realize that the Java application uses 10443 so.

  Could not start the server vcenter service, because its raise an error saying 10443 port is already im currently byt used another application.

  I tried to stop the Java service, in order to start the vcenter service and make changes to port again, numbers but I am unable to stop the java application.

  Please, if anyone knows how to change the number of Vcenter via config port or any other way, please throw a comment... Its much appreciated.

  Thank you

  Nirmal

  If you use the MSSQL database, locate WebService.Ports.http in the VPX_PARAMETER table and change to the correct port.

• Windows does not start after cleaning in Virtual Machine (XP)

  I now this is twice, using a backup after the first cleaning left me in an unbootable state.

  The full up, not cleaned up, vm works very well.  Boots, tracks and even did disk defrag very well.

  But, after you run the virtual computer cleaning off (even if I have to force the power down after that XP gives me in the trunk to disable screen machine... is it she?) the next time it is said there is a disk error and I get the BSOD.

  (though I must not force power down after that XP gives me in the trunk to put off the screen of the machine

  Whence this Virtual Machine, VMware which product was first created with?

  Also... To help understand what components are, how best to provide comprehensive diagnostic information is to use the command "Collect information to Support" the Fusion of VMware (menu bar) > help > collect Support information and then attach the .tgz file it created on your desktop for a response post.

  Also, since you have a backup (and should always before performing disk cleanup) I would start with a new copy from the backup, and then start Windows and run chkdsk c: /f in command prompt and let next start-up schedule, then restart.  So make sure that it starts towards the office okay, then stop and start the cleaning and see if it makes a difference or proportion still BSOD.

  Also if you are running AntiVirus software on the make you Mac that you're out of the Virtual Machine (s).