WINDOWS 8 PRO DOES NOT START AFTER UPGRADING THE BIOS

Similar Questions

• T530 does not start after upgrading the bios to V2.65

  Hello..

  I flashed the Bios to V2.65 under Win 10 via Lenovo Systemupdate.

  After the restart I had set default Bios and save the changes.

  Start the laptop it hang in a window to select the boot device.

  When I press on my Samsung SSD EVO nothing happened.

  I'm trying to reinstall the Bios with boot-CD. Tool said: there is no need, organic cause is real.

  Downgrade to old Bios in possible (?) not...

  It please can someone tell how to fix this?

  It comes to my work machine, and this is a disaster!

  Thanks MajorM

  Hello..

  found the solution...

  > Disable menu security-> "secure starting".

  > Start menu: UEFI/Legacy Boot-> legacy set or both

  too long, I remember. I never had problems with the bios updates.

  but it was my last... never touch a running system

  See you soon...

  MajorM

• Satellite L650d-120 does not load after upgrading the BIOS 1.7

  After upgrading the Bios up to 1.70 my laptop is no charging current, but always works to the AC adapter.
  Can I do something on my own?

  Hello

  First of all, you should set the BIOS to default settings and need to save the changes.
  You must also leave the AC adapter plugged into the laptop for a longer period of time.

  Welcome them

• Windows 8 Pro does not start after windows update updates for April

  Hello

  Pulled up to my PC this morning and was asked to install updates from windows update. Check the list, there are 11 important available updates. I have unchecked and hiding implementing Nvidia updated as I want to do the updates of my GPU myself. Installed the remaining 10, completed and has been asked to restart my PC.

  The problems starts here; I am more able to start windows.

  It is past the bios screen, shows the blue flag with a circle of rotation below and then... nothing more than a black screen and my screen goes to mode 'sleep'.

  I tried to start in safe mode minimum clean using a prompt (bcdedit/set {default} safeboot) repair my installation disk option, but it does not start even in safe mode.

  I run system restore turned on so that the option is not valid for me.

  The system is now check the disk for errors, but it seems to hang there as well as happens for more than 2 hours now...

  Any way that I can return the updates of windows on the outside? Any other suggestions than the reset of the installation disc?

  Spec: Evga x 58 classified 3, Intel Core i7 950, 2 x Geforce GTX 580 in SLI, 12 GB Corsair Dominator GT DDR3, Corsair Force 3 SSD 128 gb, Dell u2711 2560 x 1440. Win Pro 8 x 64, completely up to date with the latest drivers. PC worked perfectly up to this Point.

  Disappointed that the "major updates" Microsoft kills my work machine.

  Problem solved now and it was the update of KB2808735 who was / is the origin of the problem.

  I placed my SSD into another computer and was able to pull up in SafeMode off and remove the updates.

  Installed all the updates one by one until it chrashed again installing the update mentioned above.

• Black screen, high regular of underscore on the left does not start after reflashing the BIOS F.38 on HP2000-363NR

  HP2000 363NR, recently tried flashing the BIOS F.38 (here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116227-1&cc=us&dlc=&lc=en&o... ) to solve a problem of overheating.

  Well, it was a mistake.

  Now it does not start at all.

  Fans spinning upwards. Hard disk rotates.

  By pressing ESC, F1, F2, F9, F10 and F11 at startup to give appropriate (fast!) messages but then go to the same place:

  Black screen with flashing underscore in the top left. Leave it to this screen has no effect.

  Never see no text except the quick messages in the lower left (or "Press the ESC key for the system menu" down left based on nothing).

  Out and the relocation of memory does not work. Boot with a DIMM module does not work. Now hold power for one minute while the battery and plug on does not work.

  Battery is fully charged.

  OS is Windows 7 64 bit Home Premium, came with the laptop.

  Is it possible to return this BIOS?

  -Me

  Thanks to Xraytim in the post below, short-circuit the battery CMOS me returned to the previous BIOS. Need to remove card system as a whole to achieve this * beep * connector, but 34 screws later (34 = some # between 15 and 50), BIOS is back, problem solved.

  Thanks for the forum!

  -Tim

  http://h30434.www3.HP.com/T5/notebook-lockups-freezes-hangs/DV9858ca-won-t-boot-after-BIOS-update-won-t-power-with-AC/TD-p/555547

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• Laptop computer DV6174ea not start after upgrading the bios!

  HP dv6174ea lapop - Win XP media center edition with sp3 - processor intel core duo - 2 GB ram - 120 GB hd

  Ive just used the upgrade of bios of HP downloads flash to upgrade the Phoenix bios on my dv6174ea to version 2.9 1.06.Flashed successfully but on reboot it reaches windows XP start screen (black with logo) fails then a blue screen and restarts quickly. Same cycle occurs again and again. Ive tried to boot from the XP cd, but it gives the message "no hard drive not detected" and fails. detect the drives in the BIOS there is no options to the automobile.

  Curiously, a USB bbot containing paragon hard disk manager won't start and sees my drive (two partitions) and the system partition is active.

  I wonder if the flashing the BIOS changed settings or drive letters so that windows does not see properly. I wish there was just a simple option in the bios for detection of discs.

  Can someone pls help.

  If you want to start your computer from the xp cd, then enter the bios and it try to disable the sata mode and activate the ide mode and then try to format your drive... it should work... !!!

• Laptop not start after upgrading the BIOS crash

  Hi all

  I just want to ask if there a chance to reactivate my Satellite A300 after crash BISO update without it sends to the service of Toshiba.

  I downloaded the new BISO and he started in the Windows menu. After a few seconds my PC crashed and everything was frozen.
  I turned off the PC.
  Now, when I press the power button to boot up the laptop, the screen is black and I can a sound BRR, BRR, BRR of the CD-Rom drive.

  Don't you think that it is possible to boot from a CD or something like that. Is it possible to reactivate my phone?

  Your help would be really appreciated!

  Thank you very much

  Best regards

  Chotte

  Sorry but if the BIOS chip is damaged there is not a lot, you can do about it. You must contact the Toshiba authorized service provider.

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Windows xp sp3 does not start after the failure of windows update and restart.

  Hello

  My ADVENT 3217 pc runs windows xp sp3 does not start once a windows recently failed update and restarted. He's just in a reboot loop. The first time it happened I got an error code of c000021a. I tried pressing F8 and try to start safe mode and other options... but still nothing. I also tried to use my restore disc supplied with my pc. So far, I've only tried the non-destructive recovery to restore windows and it did not work. I don't want to lose my files that I have not saved for quite awhile.

  Can anyone help?

  Thank you

  Hello

  · The updates you have installed prior to this problem?

  You can try the steps listed in the link below: how to solve an error "STOP 0xC000021A": http://support.microsoft.com/kb/156669

• Windows Firewall service does not start after the removal of Virus

  Hello

  I believe that my son's computer has been infected with the Trojan.Agent.Ed virus.  I managed to remove it (from different folders in AppData), but a few vestiges remain of course.  The windows firewall service does not start - it throws an exception to access denied on startup and when I try to start the service manually.
  I tried to run the Sysinternals Process Monitor to display all events ACCESS DENIED and checked the permissions on the key to registry MpsSvc in HKLM\System\CurrentControlSet\services and compared to a corresponding Windows 7 machine.  I've even exported the key MpsSvc and sous-branches of the laptop in good health and tried to import into a failure, but the import does not seem to occur, even if it gives a message "imported".
  I also tried the troubleshooting of Windows Firewall that confusedly says:
  "Windows could not start the Windows Firewall... Not fixed
  "Set permissions for the registry keys involved"... succeeded
  "Windows Firewall service is not started. Not fixed
  "Starting the Firewall Service"... succeeded
  Any ideas would be most appreciated.
  Thank you.

  It seems that I solved the problem by running this:

  http://KB.ESET.com/library/ESET/KB%20Team%20Only/Malware/ServicesRepair.exe
  that I found in a post on this thread:
  http://social.technet.Microsoft.com/forums/Windows/en-us/5366225a-46e7-4D6C-A389-8bd18a5c3aad/Windows-Firewall-damaged-by-Windows-7-antivirus-2012?Forum=w7itprosecurity

• XP pro do not start after changing the Boot.ini file

  The problem is that my C: partition Windows 7
  D: has XP Pro

  These should be considered right resp. partitions 1 and 2?

  I wanted to first XP pro to start the default partition.

  A few days ago, I made a change to the boot.ini file. But since XP Pro was not starting at all.

  I tried XP Pro to start first that the default partition.

  Given that XP Pro and my D: drive have not been starting, I consulted the boot.ini file in C:, Windows 7 partition and I changed the order (i.e. partition No.) in the boot.ini file and saved it to the required location, i.e. D:/WINDOWS/pss.
  through my drive C: of work, i.e. the partition of Windows 7, but it still does not work because apparently even though I save here, the actual values and the paths of the partition are not actually be changed on the system. I confirmed this by going into the CMD shell switching to D: and by running the command D: > bootcfg.
  Apparently any values I save in the boot.ini file that I save as a text file or "All files" in D:/WINDOWS/pss/it does not actually change in the system because whenever I run the command bootfg values are remaining still and not able to be changed, because apparently it is not saved in XP Pro and the D : partition. No matter what I do and what I put in the boot.ini file to access the values through the windows 7 partition, the values that bootcfg returns me are always the same and he refuses to change the name of path or anything else. No matter what orders, I also put in bootcfg himself.

  These are the values that bootcfg gives me:
  default: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS

  Boot entries:
  Boot entry ID: 1
  Friendly name of operating system: MS Windows XP Professional
  Path: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS
  The operating system load options: / noexecute = OPTIN/FASTDETECT/usepmtimer

  My XP Pro partition is simply not booting, and it of my main partition and has all my work. It is imperative that it starts.

  My Windows CD is also not start because apparently my DVD drive does not work properly, I had the anti malware threatfire (ThreatFire) installed on my XP D:Windows program disk but have uninstalled just in case it was blocking my changes to the system.

  On C:Win7, I put the default operating system option in the Advanced tab for Win7 and the D:XP Pro to XP Pro, when he was the starter and work. Now I can only access my files D:XP Pro Player C:Win7. But XP is not just start. What shd - I do? Thks.

  I don't have a very practical windows CD but my CD/DVD drive is not read and does not properly.

  Looks like your original post stated that your cd/dvd does not work.

  Respectfully, you will continue these hap hazard patches and your computer will not start at all. I'll try to help you once again. Please follow closely.

  Start your computer by loading Windows 7. Click HERE and download EasyBCD. Install the software in trial version. Once installation is complete open EasyBCD. You will see an interface like the image below. Click Add a new entry.

  

  A new screen appears as in the image below. Use the drop down menu to select Windows NT / 2 k/XP / 2 k 3 as described below. Type the name of the operating system in the box below. Of course, it will be Windows Xp (you can add the home or Pro to the name if you want). Make sure now that there is a check mark in the box "automatically detect the correct player. Once you have completed these steps click on 'add an entry '. That's all! You are finished. If all goes well, and if you have followed these steps carefully, there, now you have a system dual boot.

  

  You can now start working on your cd/dvd problem.