T61 is unable to sleep extended when the cover closed

Similar Questions

• No standby extended when the cover closed on Satellite A40

  Hello

  I'm new to this forum and hope someone can be able to help.
  My Satellite A40 suffered a hard drive failure and I installed a new drive and to install Windows XP on drive.

  Everything works well except for the shares when the lid is closed.
  Blanks the screen but Windows continues to operate.

  I installed the power saver Tosiba, however, options drop-down menu in the configuration, (when I close the lid) don't box display only no Action. It's the same thing in Windows Power Options.

  Of course the lid closed sensor works, but I am at a loss as to where other options are passed in the Toshibe Power Saver and Windows Power Options Properties.

  Any ideas?

  Hello

  I think that the Hibernate mode is not enabled:
  Go to start? Settings? Control Panel. Make sure you have open Classic view, and then open Power Options
  In the properties of Power Options window, chose the last tab called Hibernate.

  If you are not able to see the Hibernate tab, and then Hibernate is probably not supported on your laptop. But if its visible, so you must check the option called activate the hibernation

  Click on apply or OK, and then restart Windows XP

• Frozen when the cover closed

  My laptop is Win8.1, I put it to do nothing when the lid is closed and the power options are set to stay alive.
  I close the lid of the laptop and go to work. At work, I have TeamViewer on my laptop but I can't control Firefox (I can control the rest of the operating system).
  Today, I left my laptop open and now to work, I have a total control of Firefox, but also everything else.
  Its like Firefox crashes with closed lid switch

  You can try to disable hardware acceleration in Firefox (you will need to close and restart Firefox).

  • Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Cannot cancel the option "sleep when the cover closed.

  I often use my laptop with a TV or a projector.  However, if I close the lid of the laptop goes into sleep mode.  I can't change the setting in power options because it is grayed out.  I don't want my phone open if I use another monitor.

  System:, computer laptop Samsung NP-RF511 running Windows 7 SP1

  Go to the start menu, all programs, files from Samsung.

  Open Fast Start and disable it.  If there is no control to turn off then just close it and uninstall completely in control panel, programs & features.

  You will have complete control over your power options.

  There will be no side effects to remove this "utility" useless because it doesn't do anything for you that you can't do yourself.

• Light bar will not move from the Park position when the cover flat is in place.

  I need to copy a piece of a book of music, mark it for repetition.  The book is thick enough that I must leave the cover upward.  The first 6 copied pages OK, but now all I get is a page of alll-gray.  The light bar doesn't move; It sounds like it is stuck, but only when the cover is in place.  The cover down (copy of one sheet), it works fine.

  I thought about it!  The diference between copies who worked and those who did not was the size of the paper that I used to hide the unwanted materials.  For those who worked, the sheet lying on the light bar.

  Apparently the light bar requires a white surface facing the flat, or it won't work.

• Vista on the XPS M1330 laptop lost wireless when the lid closed (using the external monitor)

  Hello

  I bought an external monitor/keyboard/mouse for my laptop XPS M1330 (connection of the monitor via a HDMI to DVI cable).  However as soon as the lid is closed the wireless network stops working - opening the lid immediately launches the application again.  A network through a physical cable connection works with the closing of the cover.  Note, the network remains connected (or at least is always intended to be connected) it has not sent or received no information, while the lid is closed.

  XPS M1330 laptop under Vista Home Premium SP1 - Wireless card is Intel PRO/Wireless 3945ABG running the latest drivers 11.5.0.32.

  Power options are obviously set to shut down the computer laptop shut down, goes to stand by, or go into hybernation when the lid is closed... it is set to 'status quo '.  The properties of the wireless card has the "Ad hoc power management" disabled and the "allow the computer to turn off this device to save power" unchecked.

  When the cover is opened, the monitor takes the maximum size of the screen of the laptop, which goes against the objective set for the monitor in the first place.

  (As a side note, the laptop also refused to work with a wired via a network connection "homeplug" - even if a hub is placed between the laptop and the homeplug - and I refuse to run a cable between the router as the laptop will be used in another room of the router).

  Is there a solution to this, or is this a problem with Vista?  (Because if this is the case, it is yet another nail in the coffin - and it becomes difficult to find any more room for nails more!  Windows 7 is fast approaching!)

  See you soon,.
  Tom

  Hi tom101449,

  ·          The WiFi was working fine earlier?

  ·          You did it all change hardware or software on your computer before this problem?

  Method 1

  If the problem occurs after you install the latest drivers Intel PRO / Wireless, you can restore the drivers for the card wireless to the previous version. For more information, see this link.

  Restore a driver with its previous version

  http://Windows.Microsoft.com/en-us/Windows-Vista/restore-a-driver-to-its-previous-version

  Method 2

  When you connect to your wireless network, make sure that the option 'Save this network' is checked.

  In addition, right-click on the network > properties, then on the connection tab, check the box that says "connect automatically when this network is in range.

  Reference:

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Dell inspiron w / xp sp3 stops when the lid closed only in mode standby

  Dell inspiron e1505 on windows xp sp3 will stop when the lid closed mode standby. In "idle mode" it shuts down for a few seconds then screen turns on and I can work as usual.  Why is it turn off in standby mode?  Happens in AC mode and battery.  is it a software problem or a hardware problem.  I see others with the same problem and vista dell.

  http://support.Dell.com/

  Dell support.

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&l=en&s=Gen&redirect=1

  Contact Dell

  http://en.community.Dell.com/forums/

  Dell forums

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• Disable the scheduled task when the cover is closed

  Hi all

  I'm working on a project using a Panel (with several buttons) and scheduled tasks.

  The problem is that when I close the Panel, scheduled tasks continue to run in the background.

  So, I wanted to know if there is a way to kill these tasks when the cover is closed.

  Thank you for your time!

  Ekibyo

  I don't think you don't need none of that: what you need to do is store the Panel object in a global variable or a property of your script object and then try to access in the task code.

  So let's say that you store the window in a global variable:

  var MyScriptPanel = this;
  

  Then in the task code, you should be able to test if the Panel object is still valid:

  try
  {
       //     Atempt to access a dummy variable:
       //     - will return undefined if the Panel is open
       //     - should throw an error if the panel is closed
      MyScriptPanel.a;
  
       //     Do your thing and reschedule the task
  }
  catch (err)
  {
      //    Cancel the task
  }
  

  Tell me if it works.

  After using many scheduleTask I must say don't really like it: I have not tested in CC, but you may notice in CS4 to 6 that it resets the cursor when the mouse is not moving or ignore some shortcuts keyboard, so I would recommend not not to schedule your task too often, or at least give the user a way to select the frequency of execution.

  EDIT: as your line is not fair:

  panel.onClose = Panel_Close();
  

  It should be...

  panel.onClose = Panel_Close;
  

  ... with no '()' so that you copy only the body of the function in the callback to onColse. But I wouldn't rely on the events of the UI for something that should work every time.

• 7520 Photosmart printer - ink cartridges carriage out when the cover is opened

  The transport does not automatically moves himself posted to the right of the machine when the lid is open.  I'm unable to change empty ink cartridges.  The machine was purchased new April 2013 and is out of warranty.  I turned off and turned it back over 15 min later, no change.

  Any suggestions?

  Hi @Clayball,

  I see that you have problems with the transport not to move to the middle in order to change the cartridges.

  I would like to help.

  I would like to do a hard reset to see if that will solve the problem.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  If the transport does not move freely when grasp the front, it's OK to gently push the carriage to the left or right to move along the rail.
  Fragments of paper can get lodge between the cart and the gas station.  It is important to look at the far right of the printer with a flashlight to make sure there is no debris.

  I handed a document with some measures to try to resolve the transport stall.

  A Message appears 'Transport Jam' on the control panel.

  If the problem persists, in 800-474-6836, please call our technical support. If you do not live in the United States / Canada region, please click the link below to get help from your region number.
  Contact HP.

  Good day!
  Thank you.

• T450s stops when the tilt/closed lid

  Hello

  I noticed this problem which looks like 3 weeks ago or not. I am running 64-bit Windows 10 on my T450s and when I start to close the screen, the screen will turn black. The red light at the rear stays on, but as soon as I fully open the screen again, the computer will be turned off completely. My options are set to put the computer in mode standby when the lid is closed, but it can happen when the tilt a few degrees. I'm on BIOS version 1.22.

  Any help would be appreciated.

  Normtw,

  The solution that has been provided to this client, Connor_o, was a repair of the equipment. He was released in a TIP Service. I recommend contacting the Lenovo Service and SEO Service TIP # T0110-SF14 / HT101490, as your system will probably require the same repair.

  Thank you

• Computer screen appear not when the cover is open, please help!

  I use my 19-inch LCD TV as a monitor for my computer laptop windows 7, because the built-in screen broke some time it y a. yesterday, I changed the settings so that whenever I close the lid of the laptop, the screen is always displayed on the TV, but now, everytime I open the cover, broken laptop screen lights up and the connection to the TV is lost , but when I close the cover image appears upward on the TV again. I tried changing the settings I changed back. Anyway I can fix this without a keyboard? Because the only one I have is on my laptop and inaccessible without the lid open. Help, please!

  Hello Hipster,

  Being this recent, try a system restore to the most recent point when everything worked very well.  See http://www.sevenforums.com/tutorials/700-system-restore.html for more information.

  Good luck!

  Kosh

• Configure my laptop to run with the cover closed and an external keyboard and monitor mouse

  I have a HP Pavilion Select g6t.  How to configure my laptop to run as a basic office, i.e. with the lid closed and outside, keyboard, mouse, & monitor?

  If you use Windows 7 or Windows Vista, see the section "Changing button walk / stop, watch and lid settings button ' in the following link:
  http://support.HP.com/us-en/document/c00825528

  If you use Windows 8, refer to the "Change power button and lid settings" section in the following link:
  http://support.HP.com/us-en/document/c03397760

• my computer would not wake from sleep when the cover iclose & open again?

  When I close the lid on my computer & open it again, the computer does not wake up, it shows just a black screen!

  Hi George,.

  From the description of the problem, it seems that the computer would not wake from sleep when you close the lid and open it again. I understand the inconvenience.

  Let us, try to perform the following methods and check if it helps.

  Method 1: Run the troubleshooter of power

  Open the troubleshooter of power

  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  For more information, connect to:

  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions

  Method 2: Troubleshoot wake the computer from sleep mode

  http://support.Microsoft.com/kb/266283

  Method 3: Update Chipset drivers

  Download and install the latest version of drivers for chipset for the computer on the computer manufacturer site and check if you are faced with the same question.

  Method 4: Run the BIOS update

  I would say as you perform the update of the BIOS by contacting the manufacturer of the computer, check if it helps.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you

• Sleep mode when the crash go

  From time to time when I turn my laptop in standby mode, it crashed after a while (maybe minutes can be a few hours in standby mode).
  I used the WindDbg tool to watch the memory.dmp file and that's what I got from the tool:
  ===============================================================================================
  DRIVER_POWER_STATE_FAILURE (9f)
  A driver has failed to fill out a power of the PRI within a specific time frame (usually 10 minutes).
  Arguments:
  Arg1: 0000000000000003, a device object has been blocking an Irp for too long
  Arg2: fffffa8025465970, physical device from the stack object
  Arg3: fffff880009f27f0, nt! TRIAGE_9F_POWER on Win7, otherwise the functional device object of the stack
  Arg4: fffffa8026efc4a0, blocked IRP

  Debugging information:
  ------------------

  DRVPOWERSTATE_SUBCODE: 3

  Nom_image: usbccgp.sys

  DEBUG_FLR_IMAGE_TIMESTAMP: 5010aafa

  MODULE_NAME: usbccgp

  FAULTING_MODULE: fffff8800acbf000 usbccgp

  DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT

  BUGCHECK_STR: 0X9F

  Nom_processus: System

  CURRENT_IRQL: 2

  TAG_NOT_DEFINED_c000000f: FFFFF880009F9FB0

  STACK_TEXT:
  "fffff880 '009f27b8 fffff800' c67983a2: 00000000' 0000009f 00000000 00000003' fffffa80 ' 25465970 fffff880 ' 009f27f0: nt! KeBugCheckEx
  fffff880 '009f27c0 fffff800' c67983d5: fffffa80'244114f0 fffffa80 '0ccde060 00000000'00000002 fffff800' c6726084: nt! PopIrpWatchdogBugcheck + 0xe2
  "fffff880 '009f2820 fffff800' c66851ea: fffffa80 ' 24411528 fffff880 ' 009f2939 00000000'00000001 00000000' 00070f45: nt! PopIrpWatchdog + 0x32
  fffff880 '009f2870 fffff800' c6683655: 00000000 00000000' fffff800 'c6684cff 00000000'00140001 fffff800' c68fe020: nt! KiProcessExpiredTimerList + 0x22a
  "fffff880 '009f29a0 fffff800' c6685668: fffff880 ' 009 c 9180 fffff800 ' c68fcf80 00000000'00000007 00000000' 0007a25d: nt! KiExpireTimerTable + 0xa9
  fffff880 '009f2a40 fffff800' c6684a06: fffffa80 '00001fa0 00000000' 009c 0080 00000000'00000000 00000000'00000002: nt! KiTimerExpiration + 0xc8
  "fffff880 '009f2af0 fffff800' c66859ba: fffff880'009 c 9180 fffff880 ' 009 c 9180 00000000 00000000' fffff880 ' 009d4f40: nt! KiRetireDpcList + 0x1f6
  fffff880'009f2c60 00000000' 00000000: fffff880 '009f3000 fffff880' 009ed000 00000000'00000000 00000000'00000000: nt! KiIdleLoop + 0x5a

  STACK_COMMAND: kb

  FOLLOWUP_NAME: MachineOwner

  FAILURE_BUCKET_ID: 0x9F_3_usbscan_IMAGE_usbccgp.sys

  BUCKET_ID: 0x9F_3_usbscan_IMAGE_usbccgp.sys

  Follow-up: MachineOwner
  ---------
  ===============================================================================================

  Someone knows how to fix this?

  The problem seems to be related to the D420:

  DRIVER_POWER_STATE_FAILURE (9f)
  A driver has failed to fill out a power of the PRI within a specific time frame (usually 10 minutes).
  Arguments:
  Arg1: 0000000000000003, a device object has been blocking an Irp for too long
  Arg2: fffffa8025465970, physical device from the stack object
  Arg3: fffff880009f27f0, nt! TRIAGE_9F_POWER on Win7, otherwise the functional device object of the stack
  Arg4: fffffa8026efc4a0, blocked IRP

  
  2: kd >! devstack fffffa8025465970
  ! DevObj! DrvObj! DevExt ObjectName
  fffffa80118602f0 \Driver\ksthunk fffffa8011860440 InfoMask field not found for _OBJECT_HEADER to fffffa80118602c0

  fffffa800e4f6840 \Driver\usbscan fffffa800e4f6990 InfoMask field not found for _OBJECT_HEADER to fffffa800e4f6810

  > fffffa8025465970 \Driver\usbccgp fffffa8025465ac0 cannot read the offbeat info from nt! ObpInfoMaskToOffset

  ! DevNode fffffa800df14010:
  DeviceInst's "\2&2ebd5f7a&0&0000USB\VID_04A9 & PID_26EF & MI_00."
  ServiceName is "usbscan.

  Search Google for the USB\VID_04A9 & PID_26EF & MI_00 HardwareID shows that the device appears to be Canon D400-450:

  http://www.Google.com/search?q=USB%5CVID_04A9%26PID_26EF%26MI_00&SourceID=IE7&RLS=com.Microsoft: en - US: IE - SearchBox & ie = & oe

  I suspect that the driver who can be the cause of the accident is the vuhub.sys, which is dated November 16, 2007.

  Can update you the driver for vuhub.sys?

  If the vuhub.sys is a component of Eltima USB network Gate for Windows, try the following link for an updated driver:

  http://wiki.Eltima.com/user-guides/USB-to-Ethernet/install-wind.html

• Satellite Pro L40 - 15A - Windows XP screen white when the cover is open

  Hey,.

  So when I closed the lid on my laptop for a while and then reopen the lid, the screen remains white (black). The only way I found to get back on the screen is to re-boot.
  In power management, I put 'Status quo' for when I close the lid on my computer and power management is ' Always on '.

  I have the latest Bios and updates to the system.

  Satellite Pro L40 - 15A
  winXP

  Any help appreciated.

  Hi ib1.

  You use the version preinstalled Windows from Toshiba or is it your own installation?

  What to update the display driver? Take a look at the Toshiba page for the new display driver:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Don t forget to look in the * archives * on Toshiba page because this model is a little older, so all of the downloads are moved in archive.

  Check this box!