TC and Telia router

I have a Telia router connected to the mediabox where the fibers are coming in. Can I connect the TC to the Telia router and use the TC as a router as well?

Not as a router... you can use it as disk hard network and wireless AP for backup TM... Without a doubt... But if install you as a router you get double NAT which is a big problem.

Tags: Wireless

Similar Questions

  • I got a new modem and the router and now I can't print wireless.

    I have a Photosmart 8450 printer.  My operating system is Windows7.  I tried to follow the Scan doctor, but I guess I'm not tech savy enough to understand.  It worked fine before the new modem and the router.  She is 'offline' and I can't understand how to put line.  Thanks for any help and easy enough for me to follow.

    Hello raedene715.

    Thanks for the transcript, it was useful.

    Please, check the network cables and connections (side of the printer and router). If possible, try a different network cable.

    See you soon!

  • I am unable to connect to my router wirelessly to parents. I tried to reset the modem and the router and it still does not work.

    Presented labtop parents and can connect via ethernet, but still cannot connect to the wireless router. Ive rebooted both the modem and the router and ive also unplugged the power source. Help, please...

    original title: unable to connect to the wireless router?

    Hi Brandon,.

    What operating system do you use? (Windows 7, Vista, XP?)
    You receive any type of error message when you try to connect?
    What exactly happens when you try to connect?
    You receive an internet connection when you connect with an Ethernet cable?
    There are a few good troubleshooting in this thread. I suggest to look to see if it helps at all:

  • Network Magic and Cisco router EA4500 UID and password

    I use the 5.5.9150.0 version of the free product. I had my last router, with a WRT400N. Since then, I have installed an EA4500 router to replace the WRT400N. I'm glad that Network Magic works with my new router, but I have a problem: I can't connect to my router via Netowrk Magic.

    Protection status/Wireless / Wireless Protection settings brings up a window that asks you the router user name and the password. I went to the page "Setting Up: Basics" guide of the user EA4500 (page 13) and tried all the values that I had copied in when I installed the router.

    I tried the SSID of the router and the "Linksys Smart Wi - Fi Username ' in the user ID box.

    I tried the "Linksys Smart WIFI password", the network, the Guest network password password and the router password (same as the network password).

    Nothing has worked. I've only connected to the EA4500 using the Linksys Smart WiFi, username and password, so I'm stuck trying to figure what values to use.

    Please help me understand what I am doing wrong. Thank you!

    I stumbled in the response:

    1. start Network Magic and display the network map.

    2. click on the name of the router (just under the router icon).

    3. click on Set Up or manage the device.

    4. the Linksys WiFi Smart Sign In (to the router) window appears.

    5 connect to the router by using the credentials of Smart Wi - Fi that you set up when you have installed the router.

    Now, all router commands will work from within Network Magic.

    :+)

  • Problem with access to the camera on the net via dsl modem and linksys router

    OK, I read all posts here on what to do in this case and think I have tried everything. I have an Actiontec dsl (verizon) and a v2 wrt110 router. I can see the camera locally, but not on the net. I had it hooked to another place but with cable service broadband with no problems.

    I think that the problem of my lie with ip addresses.

    Camera 192.168.0.115

    Router 192.168.0.1

    Modem 192.168.1.1

    The port forwards on the modem MUST be set to port forward to the IP Address of the Linksys router. It should be only the modem IP can see, so it's the only place you can move forward from the modem. What exactly is in this drop-down list in the config of the modem port forwarding?

    The problem is that there are two distinct here networks once you are inside your modem. There is a network between the modem and the router. Allthat is on it is the modem's ethernet interface and the port of the Internet router (or WAN). There is another network on the side the router as your PC's LAN, camera, etc. are on. All know the modem is how to get to the network to which it is directly connected to. While you could add a route staic on the modem to tell him how to get to this network, the modem must still know I have oprt route traffic to your camera to the router.

  • Internet connection is unreliable - when a wireless computer connects to the network, all other stands and the router needs to be reset

    I have a home wireless network with a new router Belkin (no separate modem). There are four laptop computers in our House, which connect to the wireless network. One of them is Windows 7, both Vista and the other is XP.

    Sometimes the internet works perfectly well and all four laptop computers are able to connect simultaneously. But more often... when a new laptop is on and attempts to connect, all current laptops get kicked out of the network all together and are unable to reconnect. The network broadcasts always and appears in the list of available networks, but we are unable to connect.

    Other times, if my roommate is very well on the internet and I turn on my laptop, I can't see even the network, despite the fact that it is to use! If I turn the router off and on again (sometimes we do this several times) it works OK again.

    Sometimes this happens several times a day, other times we go days without having to reset. The problems are more frequent when the old Vista laptop is used which is what made me think it may be related to computers (or their settings) rather than the router.

    Thank you

    Alex

    You may need to check every laptop and the router, to be sure.

    Go to the website of the manufacturer of your Belkin router > make sure you have the latest Firmware for it.

    Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

    Troubleshoot network adapter problems to Microsoft link above.

    Try without commitment TCP/IPv6:

    If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

    http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

    See you soon.

    Mick Murphy - Microsoft partner

  • Access to the WAN1 and WAN2 router LAN

    Hello

    I use a RV042 to save my LTE (6840 Fritzboc) router with a DSL (Fritzbox 7390) router. Now to configure the router and access the router for my VOIP phone line I need access to WAN1 and WAN2 WAN1 WAN2 and from the local network. The structure looks like this:

    LTE DSL (public IP)

    |                  |

    FB6840 FB7390 (192.168.178.202)

    |                 |

    WAN1 WAN2 (192.168.178.102)

    |__________|

    |

    RV042 (192.168.178.254)

    |

    LAN

    |

    PC (192.168.178.100)

    Are all in the same subnet (192.168.178) and the firewall access rule to access the WAN and LAN and vice versa is configured.

    Problem one)

    If I now try to ping 192.168.178.202 (FB7390) from the PC (192.168.178.100) it does not find a road to the FB7390. That's why I can not administer the FB7390 (as a solution, I use a WiFi dirct to box)

    Problem b)

    I have an unlimited plan with the LTE supplier for mobile phone calls and I would like to use from the DSL box. This is why I need a connection between the two boxes. But even when not possible to ping from FB6840 to FB7390, or vice versa.

    Any ideas how to get this working?

    Thanks in advance

    Klaus

    Hi Klaus,

    If I understand your idea, in an instant, you want a package to come to the port of WAN1 and be routed to WAN2 port, incoming whitout RV042 LAN. This is not supported by the router. It can route traffic between ports WAN, it can only from WAN, LAN and vice versa.

    Kind regards

    Bismuth

  • Static and NAT router to router VPN

    Hello

    I have two site VPN using routers. The VPN is fine, BUT - at the end of the seat, the customer has NAT entries static to allow incoming connections - any service that has a NAT static to allow incoming connections from the Internet is inaccessible in the same way. Ping, for example, doesn't have this problem because there is no static NAT entry. I tried to configure a route map-"No. - nat" according to the http://www.cisco.com/en/US/partner/tech/tk583/tk372/technologies_configuration_example09186a00800949ef.shtml , I thought I was working.

    H.O. has the IP 131.203.64.0/24 and 135.0.0.0/24 (I know, I know - I'm trying to change), and the R.O. 192.168.1.0/24.

    Bits of configuration:

    IP nat inside source overload map route SHEEP interface Ethernet0

    IP nat inside source static tcp 135.0.0.248 131.203.100.27 3389 3389 extensible

    (other static removed)

    Int-E0-In extended IP access list

    ip permit 192.168.1.0 0.0.0.255 any

    (other entries deleted)

    access-list 198 deny ip 131.203.64.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 198 deny ip 135.0.0.0 0.0.0.255 192.168.1.0 0.0.0.255

    access-list 198 allow ip 135.0.0.0 0.0.0.255 any

    SHEEP allowed 10 route map

    corresponds to the IP 198

    1 remove the static entry for the specified host the VPN problem, but obviously breaks things :(

    2. as mentioned, the VPN itself works fine, I can ping hosts perfectly.

    Any help greatly appreciated :)

    Thank you

    Mike.

    You must use the option of the route to the static NAT map. This is a new feature in 12.2 (4) T according to this page:

    http://www.Cisco.com/univercd/CC/TD/doc/product/software/ios123/123cgcr/ipras_r/ip1_i2g.htm#1079180

    He must do exactly what you want. The old, another way to do is use "The thing", where you create a loopback interface and don't make a nat interface and use routing strategy for routing VPN traffic to one address on the same subnet as the loopback interface, but not the address of the loop. IOS then that réacheminera traffic to the real destination (in this case the remote VPN site), but since now it is not a 'ip nat inside' interface, the static nat translations does not apply and the VPN traffic will not be translated. The problem with this solution is that all loopback traffic is switched to the process, so it is a bit of a hack, but these things are sometimes necessary.

    HTH

  • PIX and ADSL router.

    I have, in a site, a PIX 515 connected to a C827H (an ADSL router as PPPoE). This router provides access to the Net. In another site, I have another PIX (a 506) and another router C827H which gave access to the Net. Both sites have access to the net without problems. But when I have what it takes to establish a VPN (Ipsec) tunnel between the two sites, across the Net, I can t make the connection. The ADSL router has their public IP is negotiated with the provider. In my lab, I simulate this two connections put two PIX (a 520 and a 506) back to back with a crossover cable. I used the same configuration. The thing worked. But in my two sites that does not work. Why?

    I see, in this case. I suggest that change you the name of the ACL defined in crypto card, try not to use the same ACL you used for nat0, it poses problems sometimes.

    Try and see if it works for you.

    -Jimmy

  • VPN site to Site btw Pix535 and 2811 router, can't get to work

    Hi, everyone, I spent a few days doing a VPN site-to site between PIX535 and 2811 router but returned empty-handed, I followed the instructions here:

    http://www.Cisco.com/en/us/products/ps9422/products_configuration_example09186a0080b4ae61.shtml

    #1: config PIX:

    : Saved

    : Written by enable_15 to the 18:05:33.678 EDT Saturday, October 20, 2012

    !

    8.0 (4) version PIX

    !

    hostname pix535

    !

    interface GigabitEthernet0

    Description to cable-modem

    nameif outside

    security-level 0

    address IP X.X.138.132 255.255.255.0

    OSPF cost 10

    !

    interface GigabitEthernet1

    Description inside 10/16

    nameif inside

    security-level 100

    IP 10.1.1.254 255.255.0.0

    OSPF cost 10

    !

    outside_access_in of access allowed any ip an extended list

    access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.0.0 10.20.0.0 255.255.0.0

    inside_nat0_outbound list of allowed ip extended access all 10.1.1.192 255.255.255.248

    outside_cryptomap_dyn_60 list of allowed ip extended access all 10.1.1.192 255.255.255.248

    access extensive list ip 10.1.0.0 outside_1_cryptomap allow 255.255.0.0 10.20.0.0 255.255.0.0

    pager lines 24

    cnf-8-ip 10.1.1.192 mask - 10.1.1.199 IP local pool 255.255.0.0

    Global interface 10 (external)

    15 1.2.4.5 (outside) global

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 15 10.1.0.0 255.255.0.0

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 X.X.138.1 1

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA MD5-ESP-3DES ESP-DES-MD5

    life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds

    Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000

    Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA

    life together - the association of security crypto dynamic-map outside_dyn_map 40 28800 seconds

    Crypto-map dynamic outside_dyn_map 40 kilobytes of life together - the association of safety 4608000

    Dynamic crypto map outside_dyn_map 60 match address outside_cryptomap_dyn_60

    Crypto-map dynamic outside_dyn_map 60 value transform-set ESP-3DES-MD5 ESP-3DES-SHA ESP-DES-MD5 ESP-DES-SHA

    life together - the association of security crypto dynamic-map outside_dyn_map 60 28800 seconds

    Crypto-map dynamic outside_dyn_map 60 kilobytes of life together - the association of safety 4608000

    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-SHA-3DES ESP-MD5-3DES ESP-DES-SHA ESP-DES-MD5

    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds

    cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map

    card crypto outside_map 1 match address outside_1_cryptomap

    outside_map game 1 card crypto peer X.X.21.29

    card crypto outside_map 1 set of transformation-ESP-DES-SHA

    outside_map map 1 lifetime of security association set seconds 28800 crypto

    card crypto outside_map 1 set security-association life kilobytes 4608000

    outside_map card crypto 65534 isakmp ipsec dynamic SYSTEM_DEFAULT_CRYPTO_MAP

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    ISAKMP crypto identity hostname

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 1

    life 86400

    crypto ISAKMP policy 20

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 65535

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Crypto isakmp nat-traversal 3600

    internal GroupPolicy1 group strategy

    cnf-vpn-cls group policy internal

    attributes of cnf-vpn-cls-group policy

    value of 10.1.1.7 WINS server

    value of 10.1.1.7 DNS server 10.1.1.205

    Protocol-tunnel-VPN IPSec l2tp ipsec

    field default value x.com

    sean U/h5bFVjXlIDx8BtqPFrQw password user name is nt encrypted

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared-key secret1

    RADIUS-sdi-xauth

    tunnel-group DefaultRAGroup ppp-attributes

    ms-chap-v2 authentication

    tunnel-group cnf-vpn-cls type remote access

    tunnel-group global cnf-vpn-cls-attributes

    cnf-8-ip address pool

    Group Policy - by default-cnf-vpn-cls

    tunnel-group cnf-CC-vpn-ipsec-attributes

    pre-shared-key secret2

    ISAKMP ikev1-user authentication no

    tunnel-group cnf-vpn-cls ppp-attributes

    ms-chap-v2 authentication

    tunnel-group X.X.21.29 type ipsec-l2l

    IPSec-attributes tunnel-Group X.X.21.29

    Pre-shared key SECRET

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:9780edb09bc7debe147db1e7d52ec39c

    : end

    #2: 2811 router config:

    !

    ! Last configuration change to 09:15:32 PST Friday, October 19, 2012 by cnfla

    ! NVRAM config update at 13:45:03 PST Tuesday, October 16, 2012

    !

    version 12.4

    horodateurs service debug datetime msec

    Log service timestamps datetime msec

    no password encryption service

    !

    hostname THE-2800

    !

    !

    Crypto pki trustpoint TP-self-signed-1411740556

    enrollment selfsigned

    name of the object cn = IOS - Self - signed - certificate - 1411740556

    revocation checking no

    rsakeypair TP-self-signed-1411740556

    !

    !

    TP-self-signed-1411740556 crypto pki certificate chain

    certificate self-signed 01

    308201A 8 A0030201 02020101 3082023F 300 D 0609 2A 864886 F70D0101 04050030

    2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

    69666963 31343131 37343035 6174652D 3536301E 170 3132 31303136 32303435

    30335A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D

    4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 34313137 65642D

    34303535 3630819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101

    8100F75F F1BDAD9B DE9381FD 7EAF9685 CF15A317 165B 5188 1 B 424825 9C66AA28

    C990B2D3 D69A2F0F D745DB0E 2BB4995D 73415AC4 F01B2019 C4BCF9E0 84373199

    E599B86C 17DBDCE6 47EBE0E3 8DBC90B2 9B4E217A 87F04BF7 A182501E 24381019

    A61D2C05 5404DE88 DA2A1ADC A81B7F65 C318B697 7ED69DF1 2769E4C8 F3449B33

    010001A 3 67306530 1 130101 FF040530 030101FF 30120603 0F060355 35AF0203

    1104 B 0 300982 074C412D 32383030 551D 551 2304 18301680 14B56EEB 301F0603

    88054CCA BB8CF8E8 F44BFE2C B77954E1 52301 D 06 04160414 B56EEB88 03551D0E

    054CCABB 8CF8E8F4 4BFE2CB7 7954E152 300 D 0609 2A 864886 F70D0101 04050003

    81810056 58755 56 331294F8 BEC4FEBC 54879FF5 0FCC73D4 B964BA7A 07D 20452

    E7F40F42 8B 355015 77156C9F AAA45F9F 59CDD27F 89FE7560 F08D953B FC19FD2D

    310DA96E A5F3E83B 52D515F8 7B4C99CF 4CECC3F7 1A0D4909 BD08C373 50BB53CC

    659 4246 2CB7B79F 43D94D96 586F9103 9B4659B6 5C8DDE4F 7CC5FC68 C4AD197A 4EC322 C

    quit smoking

    !

    !

    !

    crypto ISAKMP policy 1

    preshared authentication

    ISAKMP crypto key address SECRET X.X.138.132 No.-xauth

    !

    !

    Crypto ipsec transform-set the-2800-trans-set esp - esp-sha-hmac

    !

    map 1 la-2800-ipsec policy ipsec-isakmp crypto

    ipsec vpn Description policy

    defined by peer X.X.138.132

    the transform-set the-2800-trans-set value

    match address 101

    !

    !

    !

    !

    !

    !

    interface FastEthernet0/0

    Description WAN side

    address IP X.X.216.29 255.255.255.248

    NAT outside IP

    IP virtual-reassembly

    automatic duplex

    automatic speed

    No cdp enable

    No mop enabled

    card crypto 2800-ipsec-policy

    !

    interface FastEthernet0/1

    Description side LAN

    IP 10.20.1.1 255.255.255.0

    IP nat inside

    IP virtual-reassembly

    full duplex

    automatic speed

    No mop enabled

    !

    IP nat inside source map route sheep interface FastEthernet0/0 overload

    access-list 10 permit X.X.138.132

    access-list 99 allow 64.236.96.53

    access-list 99 allow 98.82.1.202

    access list 101 remark vpn tunnerl acl

    Note access-list 101 category SDM_ACL = 4

    policy of access list 101 remark tunnel

    access-list 101 permit ip 10.20.0.0 0.0.0.255 10.1.0.0 0.0.255.255

    access-list 110 deny ip 10.20.0.0 0.0.0.255 10.1.0.0 0.0.255.255

    access-list 110 permit ip 10.20.0.0 0.0.0.255 any

    public RO SNMP-server community

    !

    !

    !

    sheep allowed 10 route map

    corresponds to the IP 110

    !

    !

    !

    !

    WebVPN gateway gateway_1

    IP address X.X.216.29 port 443

    SSL trustpoint TP-self-signed-1411740556

    development

    !

    WebVPN install svc flash:/webvpn/svc.pkg

    !

    WebVPN gateway-1 context

    title 'b '.

    secondary-color white

    color of the title #CCCC66

    text-color black

    SSL authentication check all

    !

    !

    policy_1 political group

    functions compatible svc

    SVC-pool of addresses "WebVPN-Pool."

    SVC Dungeon-client-installed

    SVC split include 10.20.0.0 255.255.0.0

    Group Policy - by default-policy_1

    Gateway gateway_1

    development

    !

    !

    end

    #3: test Pix to the router:


    ITS enabled: 1

    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

    Total SA IKE: 1

    1 peer IKE: X.X.21.29

    Type: user role: initiator

    Generate a new key: no State: MM_WAIT_MSG2

    > DEBUG:

    12:07:14 pix535:Oct 22 Oct 22 12:20:28 EDT: % PIX-vpn-3-713902: IP = X.X.21.29, Removing peer to peer table has not, no match
    !
    22 Oct 12:07:14 pix535: 22 Oct 12:20:28 EDT: % PIX-vpn-4-713903: IP = X.X.21.29, error: cannot delete PeerTblEntry
    #4: test the router to pix:
    LA - 2800 #sh crypto isakmp his
    IPv4 Crypto ISAKMP Security Association
    status of DST CBC State conn-id slot
    X.X.138.132 X.X.216.29 MM_KEY_EXCH 1017 ASSETS 0
    > debug
    LA - 2800 #ping 10.1.1.7 source 10.20.1.1
    Type to abort escape sequence.
    Send 5, echoes ICMP 100 bytes to 10.1.1.7, time-out is 2 seconds:
    Packet sent with a source address of 10.20.1.1
    Oct 22 16:24:33.945: ISAKMP: (0): profile of THE request is (NULL)
    22 Oct 16:24:33.945: ISAKMP: created a struct peer X.X.138.132, peer port 500
    22 Oct 16:24:33.945: ISAKMP: new created position = 0x488B25C8 peer_handle = 0 x 80000013
    22 Oct 16:24:33.945: ISAKMP: lock struct 0x488B25C8, refcount 1 to peer isakmp_initiator
    22 Oct 16:24:33.945: ISAKMP: 500 local port, remote port 500
    22 Oct 16:24:33.945: ISAKMP: set new node 0 to QM_IDLE
    22 Oct 16:24:33.945: ISAKMP: find a dup her to the tree during the isadb_insert his 487720 A 0 = call BVA
    22 Oct 16:24:33.945: ISAKMP: (0): cannot start aggressive mode, try the main mode.
    22 Oct 16:24:33.945: ISAKMP: (0): pair found pre-shared key matching 70.169.138.132
    Oct 22 16:24:33.945: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
    Oct 22 16:24:33.945: ISAKMP: (0): built the seller-07 ID NAT - t
    Oct 22 16:24:33.945: ISAKMP: (0): built of NAT - T of the seller-03 ID
    Oct 22 16:24:33.945: ISAKMP: (0): built the seller-02 ID NAT - t
    22 Oct 16:24:33.945: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    22 Oct 16:24:33.945: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1
    Oct 22 16:24:33.945: ISAKMP: (0): Beginner Main Mode Exchange
    Oct 22 16:24:33.945: ISAKMP: (0): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_NO_STATE
    22 Oct 16:24:33.945: ISAKMP: (0): sending a packet IPv4 IKE.
    22 Oct 16:24:34.049: ISAKMP (0:0): packet received dport 500 sport Global 500 (I) MM_NO_STATE X.X.138.132
    22 Oct 16:24:34.049: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    22 Oct 16:24:34.049: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_I_MM2
    Oct 22 16:24:34.049: ISAKMP: (0): treatment ITS payload. Message ID = 0
    Oct 22 16:24:34.049: ISAKMP: (0): load useful vendor id of treatment
    Oct 22 16:24:34.049: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
    Oct 22 16:24:34.049: ISAKMP: (0): provider ID is NAT - T v2
    Oct 22 16:24:34.049: ISAKMP: (0): load useful vendor id of treatment
    Oct 22 16:24:34.049: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
    22 Oct 16:24:34.053: ISAKMP: (0): pair found pre-shared key matching 70.169.138.132
    Oct 22 16:24:34.053: ISAKMP: (0): pre-shared key local found
    22 Oct 16:24:34.053: ISAKMP: analysis of the profiles for xauth...
    22 Oct 16:24:34.053: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 1
    22 Oct 16:24:34.053: ISAKMP: DES-CBC encryption
    22 Oct 16:24:34.053: ISAKMP: SHA hash
    22 Oct 16:24:34.053: ISAKMP: default group 1
    22 Oct 16:24:34.053: ISAKMP: pre-shared key auth
    22 Oct 16:24:34.053: ISAKMP: type of life in seconds
    22 Oct 16:24:34.053: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0x80
    22 Oct 16:24:34.053: ISAKMP: (0): atts are acceptable
    . Next payload is 0
    22 Oct 16:24:34.053: ISAKMP: (0): Acceptable atts: real life: 0
    22 Oct 16:24:34.053: ISAKMP: (0): Acceptable atts:life: 0
    22 Oct 16:24:34.053: ISAKMP: (0): fill atts in his vpi_length:4
    22 Oct 16:24:34.053: ISAKMP: (0): fill atts in his life_in_seconds:86400
    22 Oct 16:24:34.053: ISAKMP: (0): return real life: 86400
    22 Oct 16:24:34.053: ISAKMP: (0): timer life Started: 86400.
    Oct 22 16:24:34.053: ISAKMP: (0): load useful vendor id of treatment
    Oct 22 16:24:34.053: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
    Oct 22 16:24:34.053: ISAKMP: (0): provider ID is NAT - T v2
    Oct 22 16:24:34.053: ISAKMP: (0): load useful vendor id of treatment
    Oct 22 16:24:34.053: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
    22 Oct 16:24:34.053: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    22 Oct 16:24:34.053: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM2
    Oct 22 16:24:34.057: ISAKMP: (0): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_SA_SETUP
    22 Oct 16:24:34.057: ISAKMP: (0): sending a packet IPv4 IKE.
    22 Oct 16:24:34.057: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    22 Oct 16:24:34.057: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM3
    22 Oct 16:24:34.181: ISAKMP (0:0): packet received dport 500 sport Global 500 (I) MM_SA_SETUP X.X.138.132
    22 Oct 16:24:34.181: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    22 Oct 16:24:34.181: ISAKMP: (0): former State = new State IKE_I_MM3 = IKE_I_MM4
    Oct 22 16:24:34.181: ISAKMP: (0): processing KE payload. Message ID = 0
    Oct 22 16:24:34.217: ISAKMP: (0): processing NONCE payload. Message ID = 0
    22 Oct 16:24:34.217: ISAKMP: (0): pre-shared key found peer corresponding to X.X.138.132
    Oct 22 16:24:34.217: ISAKMP: (1018): load useful vendor id of treatment
    Oct 22 16:24:34.217: ISAKMP: (1018): provider ID is the unit
    Oct 22 16:24:34.217: ISAKMP: (1018): load useful vendor id of treatment
    Oct 22 16:24:34.217: ISAKMP: (1018): provider ID seems the unit/DPD but major incompatibility of 55
    Oct 22 16:24:34.217: ISAKMP: (1018): provider ID is XAUTH
    Oct 22 16:24:34.217: ISAKMP: (1018): load useful vendor id of treatment
    Oct 22 16:24:34.217: ISAKMP: (1018): addressing another box of IOS
    !
    Oct 22 16:24:34.221: ISAKMP: (1018): load useful vendor id of treatment
    22 Oct 16:24:34.221: ISAKMP: (1018): vendor ID seems the unit/DPD but hash mismatch
    22 Oct 16:24:34.221: ISAKMP: receives the payload type 20
    22 Oct 16:24:34.221: ISAKMP: receives the payload type 20
    22 Oct 16:24:34.221: ISAKMP: (1018): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    22 Oct 16:24:34.221: ISAKMP: (1018): former State = new State IKE_I_MM4 = IKE_I_MM4
    22 Oct 16:24:34.221: ISAKMP: (1018): send initial contact
    22 Oct 16:24:34.221: ISAKMP: (1018): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication
    22 Oct 16:24:34.221: ISAKMP (0:1018): payload ID
    next payload: 8
    type: 1
    address: X.X.216.29
    Protocol: 17
    Port: 500
    Length: 12
    22 Oct 16:24:34.221: ISAKMP: (1018): the total payload length: 12
    Oct 22 16:24:34.221: ISAKMP: (1018): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_KEY_EXCH
    22 Oct 16:24:34.221: ISAKMP: (1018): sending a packet IPv4 IKE.
    22 Oct 16:24:34.225: ISAKMP: (1018): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    22 Oct 16:24:34.225: ISAKMP: (1018): former State = new State IKE_I_MM4 = IKE_I_MM5
    ...
    22 Oct 16:24:38.849: ISAKMP: (1017): purge the node 198554740
    22 Oct 16:24:38.849: ISAKMP: (1017): purge the node 812380002
    22 Oct 16:24:38.849: ISAKMP: (1017): purge node 773209335...
    Success rate is 0% (0/5)
    # THE-2800
    Oct 22 16:24:44.221: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH...
    22 Oct 16:24:44.221: ISAKMP (0:1018): increment the count of errors on his, try 1 5: retransmit the phase 1
    Oct 22 16:24:44.221: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH
    Oct 22 16:24:44.221: ISAKMP: (1018): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_KEY_EXCH
    22 Oct 16:24:44.221: ISAKMP: (1018): sending a packet IPv4 IKE.
    22 Oct 16:24:44.317: ISAKMP (0:1018): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH X.X.138.132
    Oct 22 16:24:44.317: ISAKMP: (1018): package of phase 1 is a duplicate of a previous package.
    Oct 22 16:24:44.321: ISAKMP: (1018): retransmission jumped to the stage 1 (time elapsed since the last transmission 96)
    22 Oct 16:24:48.849: ISAKMP: (1017): serving SA., his is 469BAD60, delme is 469BAD60
    22 Oct 16:24:52.313: ISAKMP (0:1018): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH X.X.138.132
    Oct 22 16:24:52.313: ISAKMP: (1018): package of phase 1 is a duplicate of a previous package.
    Oct 22 16:24:52.313: ISAKMP: (1018): retransmission due to phase 1 of retransmission
    Oct 22 16:24:52.813: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH...
    22 Oct 16:24:52.813: ISAKMP (0:1018): increment the count of errors on his, try 2 of 5: retransmit the phase 1
    Oct 22 16:24:52.813: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH
    Oct 22 16:24:52.813: ISAKMP: (1018): package X.X138.132 my_port 500 peer_port 500 (I) sending MM_KEY_EXCH
    22 Oct 16:24:52.813: ISAKMP: (1018): sending a packet IPv4 IKE.
    Oct 22 16:24:52.913: ISAKMP: (1018): package of phase 1 is a duplicate of a previous package.
    Oct 22 16:24:52.913: ISAKMP: (1018): retransmission jumped to the stage 1 (time elapsed since the last transmission of 100)
    22 Oct 16:25:00.905: ISAKMP (0:1018): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH X.X.138.132
    22 Oct 16:25:00.905: ISAKMP: node set 422447177 to QM_IDLE
    ....
    22 Oct 16:25:03.941: ISAKMP: (1018): SA is still budding. New application of ipsec in the annex
    . (local 1 X. X.216.29, remote X.X.138.132)
    22 Oct 16:25:03.941: ISAKMP: error during the processing of HIS application: failed to initialize SA
    22 Oct 16:25:03.941: ISAKMP: error while processing message KMI 0, error 2.
    Oct 22 16:25:12.814: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH...
    22 Oct 16:25:12.814: ISAKMP (0:1018): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    Oct 22 16:25:12.814: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH
    Oct 22 16:25:12.814: ISAKMP: (1018): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_KEY_EXCH
    22 Oct 16:25:12.814: ISAKMP: (1018): sending a packet IPv4 IKE.
    Oct 22 16:25:22.814: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH...
    22 Oct 16:25:22.814: ISAKMP (0:1018): increment the count of errors on his, try 5 of 5: retransmit the phase 1
    Oct 22 16:25:22.814: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH
    Oct 22 16:25:22.814: ISAKMP: (1018): package X.X.138.132 my_port 500 peer_port 500 (I) sending MM_KEY_EXCH
    22 Oct 16:25:22.814: ISAKMP: (1018): sending a packet IPv4 IKE.
    Oct 22 16:25:32.814: ISAKMP: (1018): transmit phase 1 MM_KEY_EXCH...
    22 Oct 16:25:32.814: ISAKMP: (1018): peer does not paranoid KeepAlive.
    ......

    22 Oct 16:25:32.814: ISAKMP: (1018): removal of reason ITS status of 'Death by retransmission P1' (I) MM_KEY_EXCH (post 70.169.138.132)

    22 Oct 16:25:32.814: ISAKMP: (1018): removal of reason ITS status of 'Death by retransmission P1' (I) MM_KEY_EXCH (post 70.169.138.132)

    22 Oct 16:25:32.814: ISAKMP: Unlocking counterpart struct 0x488B25C8 for isadb_mark_sa_deleted(), count 0

    22 Oct 16:25:32.814: ISAKMP: delete peer node by peer_reap for X.X.138.132: 488B25C8

    22 Oct 16:25:32.814: ISAKMP: (1018): error suppression node 1112432180 FALSE reason 'IKE deleted.

    22 Oct 16:25:32.814: ISAKMP: (1018): error suppression node 422447177 FALSE reason 'IKE deleted.

    22 Oct 16:25:32.814: ISAKMP: (1018): node-278980615 error suppression FALSE reason 'IKE deleted.

    22 Oct 16:25:32.814: ISAKMP: (1018): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL

    22 Oct 16:25:32.814: ISAKMP: (1018): former State = new State IKE_I_MM5 = IKE_DEST_SA

    22 Oct 16:26:22.816: ISAKMP: (1018): purge the node 1112432180

    22 Oct 16:26:22.816: ISAKMP: (1018): purge the node 422447177

    22 Oct 16:26:22.816: ISAKMP: (1018): purge the node-278980615

    22 Oct 16:26:32.816: ISAKMP: (1018): serving SA., its A 487720, 0 =, delme = A 487720, 0

    The PIX is also used VPN client, such as the VPN Cicso 5.0 client access, works very well. Router is used as a server SSL VPN, too much work

    I know there are a lot of data here, I hope that these data may be useful for diagnostic purposes.

    All suggestions and tips are greatly appreciated.

    Sean

    Recommended action:

    On the PIX:

    no card crypto outside_map 1

    !

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    !

    card crypto outside_map 10 correspondence address outside_1_cryptomap

    crypto outside_map 10 peer X.X.216.29 card game

    outside_map crypto 10 card value transform-set ESP-3DES-SHA

    life safety association set card crypto outside_map 10 28800 seconds

    card crypto outside_map 10 set security-association life kilobytes 4608000

    !

    tunnel-group X.X.216.29 type ipsec-l2l

    IPSec-attributes tunnel-Group X.X.216.29

    Pre-shared key SECRET

    !

    On the router:

    crypto ISAKMP policy 10

    preshared authentication

    Group 2

    3des encryption

    !

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    output

    !

    card 10 la-2800-ipsec policy ipsec-isakmp crypto

    ipsec vpn Description policy

    defined by peer X.X.138.132

    game of transformation-ESP-3DES-SHA

    match address 101

    !

    No crypto card-2800-ipsec-policy 1

    Let me know how it goes.

    Portu.

    Please note all useful posts

    Post edited by: Javier Portuguez

  • VPN between ASA and cisco router [phase2 question]

    Hi all

    I have a problem with IPSEC VPN between ASA and cisco router

    I think that there is a problem in the phase 2

    Can you please guide me where could be the problem.
    I suspect questions ACL on the router, but I cannot fix. ACL on the router is specified below

    Looking forward for your help

    Phase 1 is like that

    Cisco_router #sh crypto isakmp his

    IPv4 Crypto ISAKMP Security Association
    status of DST CBC State conn-id slot
    78.x.x.41 87.x.x.4 QM_IDLE 2006 0 ACTIVE

    and ASA

    ASA # sh crypto isakmp his

    ITS enabled: 1
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 1

    1 peer IKE: 78.x.x.41
    Type: L2L role: initiator
    Generate a new key: no State: MM_ACTIVE

    Phase 2 on SAA

    ASA # sh crypto ipsec his
    Interface: Outside
    Tag crypto map: Outside_map, seq num: 20, local addr: 87.x.x.4

    Outside_cryptomap_20 ip 172.19.209.0 access list allow 255.255.255.0 172.
    19.194.0 255.255.255.0
    local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
    current_peer: 78.x.x.41

    #pkts program: 8813, #pkts encrypt: 8813, #pkts digest: 8813
    #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 8813, model of #pkts failed: 0, #pkts Dang failed: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 87.x.x.4, remote Start crypto. : 78.x.x.41

    Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
    current outbound SPI: C96393AB

    SAS of the esp on arrival:
    SPI: 0x3E9D820B (1050509835)
    transform: esp-3des esp-md5-hmac no
    running parameters = {L2L, Tunnel}
    slot: 0, id_conn: 7, crypto-card: Outside_map
    calendar of his: service life remaining (KB/s) key: (4275000/3025)
    Size IV: 8 bytes
    support for replay detection: Y
    outgoing esp sas:
    SPI: 0xC96393AB (3378746283)
    transform: esp-3des esp-md5-hmac no
    running parameters = {L2L, Tunnel}
    slot: 0, id_conn: 7, crypto-card: Outside_map
    calendar of his: service life remaining (KB/s) key: (4274994/3023)
    Size IV: 8 bytes
    support for replay detection: Y

    Phase 2 on cisco router

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
    current_peer 87.x.x.4 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
    current outbound SPI: 0x0 (0)

    SAS of the esp on arrival:

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:

    outgoing ah sas:

    outgoing CFP sas:

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.19.194.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (172.19.209.0/255.255.255.0/0/0)
    current_peer 87.x.x.4 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 8947, #pkts decrypt: 8947, #pkts check: 8947
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 78.x.x.41, remote Start crypto. : 87.x.x.4
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer0
    current outbound SPI: 0x3E9D820B (1050509835)

    SAS of the esp on arrival:
    SPI: 0xC96393AB (3378746283)
    transform: esp-3des esp-md5-hmac.
    running parameters = {Tunnel}
    Conn ID: 29, flow_id: Motorola SEC 1.0:29, card crypto: mycryptomap
    calendar of his: service life remaining (k/s) key: (4393981/1196)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0x3E9D820B (1050509835)
    transform: esp-3des esp-md5-hmac.
    running parameters = {Tunnel}
    Conn ID: 30, flow_id: Motorola SEC 1.0:30, card crypto: mycryptomap
    calendar of his: service life remaining (k/s) key: (4394007/1196)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    VPN configuration is less in cisco router

    access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
    access-list 101 permit ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
    access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
    access-list 101 permit ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
    access-list 101 permit ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
    access-list 101 permit ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

    access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
    access-list 105 deny ip 172.19.206.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
    access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
    access-list 105 deny ip 172.19.203.0 0.0.0.255 172.19.194.0 0.0.0.255 connect
    access-list 105 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect
    access-list 105 deny ip 172.19.209.0 0.0.0.255 172.19.194.0 0.0.0.255 connect

    sheep allowed 10 route map
    corresponds to the IP 105

    Crypto ipsec transform-set esp-3des esp-md5-hmac mytransformset

    mycryptomap 100 ipsec-isakmp crypto map
    the value of 87.x.x.4 peer
    Set transform-set mytransformset
    match address 101

    crypto ISAKMP policy 100
    BA 3des
    md5 hash
    preshared authentication
    Group 2
    ISAKMP crypto key xxx2011 address 87.x.x.4

    Your permit for 105 ACL statement should be down is changed to match because it is the most general ACL.

    You currently have:

    Extend the 105 IP access list
    5 permit ip 172.19.194.0 0.0.0.255 (18585 matches)
    10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
    30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
    50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

    It should be:

    Extend the 105 IP access list
    10 deny ip 172.19.194.0 0.0.0.255 172.19.206.0 0.0.0.255 connect
    30 deny ip 172.19.194.0 0.0.0.255 172.19.203.0 0.0.0.255 connect
    50 deny ip 172.19.194.0 0.0.0.255 172.19.209.0 0.0.0.255 connect

    IP 172.19.194.0 allow 60 0.0.0.255 (18585 matches)

    To remove it and add it to the bottom:

    105 extended IP access list

    not 5

    IP 172.19.194.0 allow 60 0.0.0.255 any

    Then ' delete ip nat trans. "

    and it should work now.

  • Can not connect with the Adobe server to upgrade the PS. Tried with fiervall and the router and called my provider. She is also only CC there are problems!

    Can not connect with the Adobe server to upgrade the PS. Tried with fiervall and the router and called my provider. She is also only CC there are problems!

    Check your hosts file.

    help for that and other adobe.com sure common connection problems read, http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  • The Time Capsule and Comcast router compatibility

    I plan on buying Time Capsule.

    My ISP is Comcast and borrow the gateway (modem and router together)

    Comcast has not recommended the use of Time Capsule as wifi router

    I would like to know if there are problems (slow wifi, etc.) using Time Capsule with Comcast.

    It is very well - at least, it will work without problems.

    You will probably find yourself with two wireless networks - the Comcast box and time Capsule (from memory, you can not deactivate their wireless gateway), but since you get to choose which network to join you shouldn't have a problem.

  • Printer HP Photosmart more B210 loses the wireless connection. with MAC 10.6 and Linksys router.

    From time to time my printer HP PSt + B210 indicates not 'online' in the window of the printer utility and do not print.

    I have spend hours to review what I did in th past and become confused.

    Should I start with the HP utility and make sure that my printer is listed only once in the queue (as is sometimes show 2 forms - for the same printer) OR should I stop MAC PB > router > Modem and then restart in correct, reverse order?

    Given that I need to choose "IP automatically...". ", I used Safari and put the 192.168.1.1 in the address bar and follow these steps, as already suggested.  What would be the clear measures to reconnect my HP printer status online? Thank you very much!!

    We will set an IP address of the printer:

    -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
    -Enter the IP address in a browser to reveal the internal settings of the printer.
    -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
    -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
    -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
    -Enter the IP of your router (on the Page of the Network Config) for the bridge and the first DNS. Let the second white.
    -Click 'apply '.

    Now, stop the router and printer, start the router, wait, and then start printing.

    After that, you will have to redo 'Add printer' using the new IP address.

  • Securing internet connection Wi - Fi with Equium L10 and Belkin router

    Hello

    I installed a wireless belkin router on my laptop L10 and have an excellent connection to the internet - everything works fine. However, I would like to secure the connection to prevent indiscreet listening - I tried to do this under the encryption and authentication of the menus, but I'm not sure about the different acronyms used - eg Shared, WEP and WPA for example.

    I tried different combinations of these, but the laptop disconnects just from the router until I return to the connection 'open' standard with encryption disabled. Can someone point me in the right direction... ??

    Hello Dan

    Your router is unknown to me, but encryption is still working on the same path. Check the security settings of your router, then select security options. Set the encryption you want to use (WEP) and the password.
    Your device must be configured as described on this page
    http://LSS.wisc.edu/~Sara/wireless/pcwepconfig.htm

    If everything is done on the right track to avoid any problems. I also use WIFI at home with 64-bit encryption, and I spent 10 minutes for any configuration.

Maybe you are looking for

  • A way to remove the photo album of "places"?

    I really don't like the new photo albums that set off with iOS 10 (places and people) is it possible to completely delete these albums? Or at least delete items already in these records? Also while I'm here... I used to have my history of safari, the

  • Can driver Intel AHCI_13.2.0.1016 change R7-371-59zk (A13) BIOS parameter RAID0 in AHCI?

    Hello I improve my R13, R7 - 371 T (product ofJan 2015), but I couldn't open the BIOS settings. Mine has a 128 G m2 SSD and seems to be set RAID 0 (which was found in the control panel of device driver of Windows 8, I have to open the menu of the BIO

  • Windows 8.1 secure pro Boot is not configured properly

    After the upgrade through shop windows to Windows Pro 8.1, I get the watermark: «windows 8.1 secureBoot pro is not configured properly to build 9600» I went into the BIOS, tried allowing the secure startup, disabling, restore the factory keys, but no

  • How to create the restore disks

    original title: how to create a system restore disks for my computer restore disksThanks, mb

  • UCS C200 RAID solution

    Hello I hope for your help about the technical question about the RAID. We bought a server in a rack of Cisco UCS C200. Now I looking for information on the best RAID solution in our case. The question: As I understand it, there is an integrated RAID