Tecra A6 won't start

Similar Questions

• Tecra A4 won't start no-switches power off after 3 seconds

  Hey all,.

  I really hope you can help me on this. I recently bought a step expensive laptop Toshiba Tecra A4 to Ebay. He said there is a disk failure hard only... it's not.

  When I try to turn on the laptop, the lights come on and the DVD player starts to turn... everything is normal. But then after about 3 seconds it stops before that it can reach the bootscreen - as I would remove the power cable.
  The very strange thing is that sometimes we'll tell every 1 15 try the laptop starts as it should be and start my Linux live CD. Then I can work for hours, and bad don't get passes nothing... until I want to turn it back on. Then the game starts from the beginning.

  I tried already to:

  -Remove the hard drive from default
  -remove the power cable
  -only remove the battery
  -replace the RAM or be one of the two
  -to remove the two RAM
  -remove the power cable and the battery during the night to reset the CMOS

  ... nothing has changed.

  I would be very happy if someone could help me. So far, I have found that the writings of forum without response to this problem in the WWW - if at least I'm not the only crazy :-)

  Thank you very much

  Hans

  > When I try to turn on the laptop, the lights come on and the DVD player starts to turn all normal. But then after about 3 seconds it stops before the splash screen, it can reach

  My friend had the similar problem, but a replacement RAM helped.
  In your case, it might be everything. (motherboard, etc.)

  The BIOS can be updated from windows OS since only based victory of BIOS is available for download The ASP (partner) would update the BIOS but to be honest, I doubt it s a BIOS related issue to me it sounds like a hardware problem

• Tecra A4 won't start on DVD or network to allow the factory restore

  I have a Toshiba Tecra A4, I insert the recovery CD and try to boot it on the CD player and the computer simply ignores the CD player. I change the bios so it should start on the last drive, but she always starts here everything first. If I remove the hard drive it will boot on the CD player. I even removed the hard drive and remove the main partitition (leaving the recovery partition) and I can get the laptop to boot to the CD drive, but after the first reboot, it goes back to ignore the CD drive and try to boot to the hard drive only. I've never seen anything like this. Any ideas on how to fix it or work around it?

  Thank you.

  Hello

  In your case I would recommend set the BIOS default settings and save the changes.
  Then turn on the laptop, and then press F12.
  Then a start menu should appear and you should be able to choose the STRANGE as a boot device.

  Generally, if there is no hardware problem this procedure should work.

• Tecra A4 won't start even in safe mode

  Today I close my Tecra morning, put it in my bag to take to work, that it works but does not use it at all, and tonight when I tried to start it again, it does not start.

  I get to the screen that says:

  We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.

  If your computer stopped responding, restarted unexpectedly, or was automatically closed down to protect your files and folders, select last good known Configuration to return to the most recent settings that worked.

  If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button has been activated, or if you are not sure what caused the problem, choose Start Windows normally.

  Safe mode
  Safe mode with networking
  Safe with command prompt

  Last good Configuration known (your most recent settings that worked)

  Start Windows normally

  Use top and down arrow keys to move the selection of your choice.

  None of the above options, works they come back just the same screen and I have no other options.

  I also tried to put my Toshiba Tecra A4 product Recovery DVD-ROM and when I first did it is scope loudly for a minute without doing anything, and when I tried the above again, it comes back to the same screen as before.

  Most of my files is saved, but there are some that are not, and I don't want to lose them.

  Can someone give me some ideas to solve this problem?

  Thank you
  David

  Hmmm. very strange

  I think you should try to format the whole HARD drive with an original CD of Microsoft Windows XP.
  Delete all partitions and reinstall the operating system.

  If you want to save the files on the HARD drive, then I recommend to remove the portable computer HARD drive and plug it into the second computer via external USB HDD controller.

  After that backup files put the laptop HARD drive, access to the BIOS, set the default BIOS settings and save the settings.

  Then use the Xp CD to format drive HARD and new installation.

• Tecra 2100 won't start

  My laptop won't let me start and get on because it says I have a problem of 32\Driver\pci.sys of the system. I'm not amything to this topic because of my inability to start. Is there a way to fix this? Any help would be grateful.

  Hello

  There the message that Pci.sys is missing or damaged? Did you use new hardware components? Have you done something that you don t mentioned?

  You can start a license XP CD and start the console. There, you can reload the driver! Otherwise, use the XP restore tool!

• Tecra M10 - does not start only beeps

  My Tecra won't start. It sounds right. I checked the RAM and battery. I removed the keyboard, but without success.

  What is going on?

  Concerning

  Hello!

  Normally beep code at startup means that it s something wrong with the hardware (hardware malfunction).

  To identify what is the cause, you can search with Google. There are a few websites that shows what the beep code (depending on the BIOS you have).

  It could be the RAM, CPU, graphics card or something on the motherboard.

  But if your laptop is under warranty, you can contact an ASP. The repair should be free. ;)

  Good bye

• Tecra A11 won't recover/restart of sleep

  Hi guys,.

  I have a TECRA A11 model no - PTSE1A - 00M 005.
  It has Windows 7 Professional 64 bit and is up-to-date on all windows update.

  When I click the power button and send it to sleep (power button / stop is set to sleep) or close the cover and he goes to sleep, I can't click the power button again and recover or restart from sleep. It doesn't do anything.
  Power, power sector and battery plug lights up green but the hard drive does not start, or I do not see the hard drive Led light up.
  I have to keep the power button for 5 seconds to stop the laptop, and then restart it.

  In addition to this, I also have times when the computer is turned off correctly, but when I go to start it, it won't start. As usual the left 3 lights, but the hard drive light does not illuminate. The fan starts, but the computer will not start. I have to press the power button again for 5 seconds for the computer, close and then restart. The second time round it always starts.

  This problem has me baffled for a while now and I can't find a solution for this.
  Any help would be much appreciated.

  Thank you

  Since when did you notice this kind of behavior?

  Try please set the BIOS to default settings and check the startup problem.

  FN + F3 to put the laptop into sleep mode, close the cover and after a few minutes open the cover and press the power button. The same problem happens again?

• Tecra S1 does not start-> beep code appears

  Hello

  I have a problem with my Toshiba Tecra S1.
  It won't start, just beep like this:
  -Two shorts and a long
  -So, three short films and and etc.

  I can't find out what BIOS and the significance of these beeps.

  Can someone help me?
  Thank you
  Duditz

  As far as I know, it's an Insyde BIOS on the Tecra S1.
  But I thought you wanted to contact the Toshiba service provider?
  Believe me, the BIOS beep code can be read by a technician with a lot more experience as a common user.
  Eventually, you'll be able to read but you don t know what the code means.
  The meaning of the code differs from BIOS and laptop model
  I don t see other than by contacting the guys services

• Tecra S2 does not start battery mode

  Hello

  I bought Tecra S2 last week. When starting in a few hours battery mode after working with netpower, I get only a light orange for battery LED but the laptop won't start. I have to take the battery out, put it back in, connect to netpower and then only, it starts up.
  However, the battery seems to load. When I work with netpower and I disconnect netpower, yet portable functions on battery.
  Any suggestions what could be the cause and what todo?

  THX

  [Edited by: admin]

  Hello

  The machine is new and it should work properly. In my opinion, you should contact your local dealer and tell him that you want to have a new unit. As far as I know that you have 14 days return altogether.

  Good bye

• Tecra S1 does not start and hangs at the splash screen (boot)

  Tecra S1 model PT831E-107EQ-GR

  Problems started a month ago. Randomly, he didn't not started. After some power or off attempts it finally started and worked properly. I bought a new hard drive (Toshiba 40 GB) because it happened more often. I got Acronis True Image and planned to clone a disk to the new disk. The problem is that a cell phone now won't start any more so I can't boot from a CD or hard drive. It stops at the logo 'In Touch... "with text" Press [F12] for boot device selection menu ' and does not react any key. I tried to boot with no CD, no disk hard - the same thing. I also connected internal HD using ATA to USB adapter - even. This means that it is not a disk problem but motherboard, or other components? Is it possible to get into the BIOS before boot selection screen?

  Kind regards
  Jacek

  Hello Jacek

  Try to enter the BIOS to ESC settings initially upwards.
  The question is strange and I do not think that anyone here can offer the exact diagnosis. The fact is, you can use multiple bootable devices but if there is something wrong with the motherboard HARD drive CD/DVD doesn't work. CD/DVD or HARD disk controller is maybe defective.

• my iphone 6s erased and won't start

  My Iphone 6s erased and won't start

  Hello

  Follow the instructions here, including contacting Apple Support or your Genius Bar reservation if necessary:

  If your iPhone, iPad or iPod touch won't turn on - Apple Support

• Another that holding down the power button, then by restarting, how should I manage my end 2009 27 "iMac when he crashes on the first blank white screen and won't start?

  Another holding down the power button, then by restarting, how should I handle turn on my end 2009 27 "iMac when he crashes on the first blank white screen and won't start?

  Combinations of keys start for Mac - Apple Support

• Equium A100-147 tried to update BIOS, now won't start

  I was updating the BIOS on my laptop and now it won't start, the screen stay black and I just hear three beep. A long-term follow-up of two short.

  Any help would be appreciated,
  Thank you.

  > I was updating the BIOS on my laptop and now it does not start

  It seems that the update of the bios that went bad and had to be reflashed. Bios recovery is a delicate procedure and you should contact the service center:

  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT/

• Satellite Pro 6000 won't start or do something

  Hello

  My satellite pro 6000 stopped working all of a sudden.
  Power led, battery, keyboard LED is on, but nothing happens, tried to remove the battery, cd, hd and put them back, nothing seems bad.
  Also tried the back button back in case but no tip was not all good.
  It just won't start at all.

  Any ideas out there?

  Thank you

  [Edited by: moderation of the Forum]

  Do the job of seem´to LEDs ok, or they do a code flashing for you say that it is something wrong?

• Qosmio G20 - won't start, error ATA #1

  I have a G20-102. Today I opened my flash drive and files all showed them as shortcuts. I tried to connect to Firefox 4 and a warning from AVG threat came pointing to C:\windows\system32\mssrv32.exe (Tr/Crypt.xpack.Gen3) as a Protection of identity. I opted for the "Move to vault" option and asked to restart

  Now my pc won't start - I get the Qosmio screen, ATA error #1 (CD player has been removed) and then the screen "rolls" - looks like random pixels flashing on the screen. I'm trying to start safe mode, but F5, F8 or any Fkey is not doing

  To make things worse, the CD rom has been removed, faulty, so I can't boot from another device. I don't have a USb in the BIOS, only FDD option which I did not

  Help, please

  Hey,.

  To me, it looks like a serious hardware malfunction

  You could try to load the default settings in the BIOS. Enter in the BIOS, and then press the F9 key to load defaults. Then save & exit the BIOS and try to start again.

  The HARD drive is recognized correctly in the BIOS? If so I try a recovery disk Toshiba recovery installation and check if the problem is hardware or software partners.