Tecra A7: When the battery starts charging?

Similar Questions

• How do I know when the MacBook is charged

  Show the retina MacBook battery 12 "will load if you lift the screen while the MacBook is power off and load?

  Cargo stops when the battery is charged to 100%.

• Tecra R10 - 10W - charge when the battery fully

  Hello

  I have this laptop for a few weeks and his strange behavior. Lets say I use this connected to AC and the battery is charged to 100%. When I disconnect from AC from one day to the next and connect it again in the morning, he begins to charge the battery, even if it is charged to 100%. It charges the battery for 5-10 minutes.
  Does anyone have a similar experience?

  Other portable wait until the battery level reaches about 95% before loading. Is there a way I can influence this behavior? I guess that this short of frequent charges is not good for the duration of battery life.

  Thanks for your opinions.

  Hello

  > Lets say I use this connected to AC and the battery is charged to 100%. When I disconnect from AC from one day to the next and connect it again in the morning, he begins to charge the battery, even if it is charged to 100%. It charges the battery for 5-10 minutes.

  As Akuma has suggested, it's a normal question.
  Nothing unusual, because the battery loses power even the laptop is turned off.

  Here is one of the Toshiba articles:
  + Why my laptop loses 2 to 4% of its energy from the battery whenever I turned the unit off and turn it back on? +
  http://APS2.toshiba-tro.de/KB0/FAQ6301EP000ER01.htm

• L50 - B satellite will not start when the battery is completely discharged

  Hello

  My Toshiba L50 - B won't start when the battery is fully drained but connected to the power outlet.
  I try to work most of the time on the battery to keep the battery in good shape, but when I forgot to turn off the battery drains and the system will not start when I plug in the adapter.

  The battery charge indicator is orange light as it should. Only when the battery is fully charged to 100%, it will run at startup and function normally after that. I tried to turn on the laptop several times during the charge cycle, but only when the charge indicator changes from yellow to white it starts. Tested for 2 bodies.

  My old Toshiba always immediately turned on when I plugged the adapter even when the battery has been completely drained. Am I missing a setting somewhere?

  Thanks for responding... I hope well :-)

  Toshiba L50 - B
  Windows 8.1
  Any standard/original setting since I only acquired this laptop a month ago.

  The laptop should light up if the power adapter is plugged in and power the laptop corectly any if the battery is empty or during charge.

  Please check the version of the BIOS that is available on your mobile phone and compare with the BIOS available on the page of the Toshiba UE driver
  Maybe you need to update the BIOS, but to be honest, the history seems really odd to me and I m afraid that there could be some power supply electronic problem

  So in the worst case, the laptop must be checked by authorized service provider.

• Satellite A30: when the adapter is connected the battery stops charging

  Using a Satellite A30 about three years. Recent problem is that while the power adapter is plugged the battery stops in charge, the orange battery indicator turns off.

  If you look at the power management utility battery poweer bed On Line, % of discharge meter

  So he can load either, I have to turn the machine off (completely or to hibernate) then remove the power cable and reintegrate them, then the battery light turns on. When restart the battery will begin charging for a while, and then for no apparent reason in defence start.

  If left reaches 0% battery - the machine continues to operate when the power cable is connected so its power do ok, but of course starts to beep when it goes below 10%. To get it going again, I need to stop and restart etc.

  I have checked the bios and have the latest version.

  I cleaned around the outlet heat exchanger and deleted all the fluff.

  I use a generic adapter that the original does not, but as far as I can tell its working normally.

  All thoughts

  Richard

  Hi Richard,

  Your problem is caused by a bad connection where the power adapter is connected to the Jack at the back of your laptop. A slight movement of the cable causes a momentary loss of contact and electronics of management power in Notepad is deceived into beleiving that the battery is no longer available, in which case when the battery goes out and the laptop will return to the battery power even if the AC adapter is connected. As you have already discovered, turn off the laptop will be all back to normal.

  I have experienced the same situation with my A30-141 and have not yet found one solution other than to resort to power off the laptop computer, but I managed to avoid the problem occurs by pinching the cable ca at the back of the laptop so that there is no risk of power do not connect the bending in order to trigger the problem in the first place. This has been a remarkable success to date, and I didn't have a problem for several months now.

  Obviously, it is not a "cure" for the problem but the frustration it causes.

  Kind regards

• My dv6 - 3013cl starts when the battery is in

  My dv6 starts when the battery is in. I have to remove the battery and then start. The battery can't hold a charge, is empty. Is someone experienced similar problem? Thank you

  Hello hpdv579,

  Take a look at this document for battery/power problems.  Looks like you already have a diagnosis of your own problem.

  Good luck!

• Update the BIOS on a Tecra M5 - 386 when the battery is not recogised.

  My battery is not seen by my Tecra M5, but still fresh and feeds the laptop, I found info that offers as well as an upgrade of the BIOS might help, but the software update me gives an error message "[error] AC adapter is not connected, or battery power is not enough." How can I update the BIOS by bypassing the software security device? Told me on another forum that execution of the update .exe with /forceit BIOS in the CMD window that did not work. Can anyone help please.

  In most cases, the update of the BIOS does not solve battery problems
  Maybe the battery starts to malfunction because of age.

  I would recommend replacing the battery first!

  By the way; I guess the while the update of the BIOS error because of the software required missing; If you are using Win XP, then you must install page European driver of Toshiba common Modules. If you are using Windows 7 you must install VAP (value added package)

• Sound notification when the battery is fully charged?

  Hi, I want a signal when the battery is fullcarge. I don't find it. Sony Xperia Z5

  Parameters
  Accessibility
  Sounds when the battery is fullcharge

• Use of AC when the battery is at 100%? (S7-391)

  Hello world!

  I have been affected by the worst support from Acer, I have no problem with the ultrabook himself (Acer Aspire S7-391) but I have some doubts about pilots and other things, that they have avoided answering many ways. So, here's the thing:

  This ultrabook has all drivers that could be use the AC power when the battery charge reaches 100% to avoid tampering with the battery?

  The thing is that while I have 100% of the battery and the ultrabook is connected to the power adapter, it always seems to be draining the battery power and recharging it back to being 100% all the time.

  When I ask about the drivers, who might or might not be installed, I just need to find a way to access this functionality if possible, and if I can't, I need to know as soon as POSSIBLE so that I can start unplug the laptop right after that the battery has reached 100%.

  Thanks in advance.

  As you said with Connector 2 power pins can also disconnect the battery charge. It can disconnect the power supply from the battery charging circuit when the battery reaches a particular % with the laptop running load in power cables. I do not think that your computers support portable setting the level of charge of battery to a % custom. Your laptop must have a particular hardware and BIOS that supports. In some laptops, the BIOS has the ability to define a particular % of battery charge. I read somewhere that windows 8 do not support this feature, old version of windows (Vista) support this feature.

  Some write up I found online to help you.

  Memory effect

  First of all, it is necessary to unfold a myth that persists in the minds of many people.

  The effect of stack memory.

  In the basis of lithium batteries, it is in fact a myth, it applies only to the old nickel-based batteries. Therefore fully discharge and recharge the battery are completely useless and even harmful as discussed below.

  The modern lithium battery can be charged independently of its current percentage, because he has absolutely no negative effect in his performances.

  Should I remove the battery when the a/c is connected?

  Many users of portable computers have this question and we will answer it right now:

  The answer is: YES and NO, it depends on the situation.

  Have a fully charged battery and the laptop is connected is not harmful, because as soon as the load level of 100% of the battery stops receiving the energy load and this energy is shorted directly on the power of the laptop system.

  However, there is a downside to keep the battery in the holder when the laptop is plugged in, but only if he currently suffers from excessive warming caused by the hardware of the laptop.

  So:

  -In normal use, if the laptop does not get too hot (CPU and hard drive around 40 ° c to 50 ° c) the battery must remain into the Jack of the laptop;

  -Intensive use, which leads to a large amount of heat produced (i.e. games, temperatures over 60 ° c) the battery should be removed the socket in order to avoid unwanted heating.

  The heat between the fact that he has 100% load, is the great enemy of the lithium battery and not the plug, as many might think so.

  Battery discharging

  Full battery discharges (until the computer laptop power shutdown, 0%) should be avoided, because he insists a lot on the battery and may even damage it. It is recommended to perform partial discharge to levels of capacity of 20 ~ 30% and frequent accusations, instead of performing a complete discharge followed for a full charge.

  Laptop PC battery contain a gauge of capacity that allows us to know the exact amount of stored energy. However, due to the charge/discharge cycles, this sensor tends to be inaccurate overtime.

  Some laptops include in their BIOS, tools to recalibrate the battery meter, which is nothing else than a full discharge followed by a charge complete.

  So to calibrate the gauge, it is desirable, in all cycles 30 discharge, a full uninterrupted discharge, followed by a too, non-stop, full charge.

  An inaccurate gauge may have to the fact that the capacity of the battery are values are false. The battery can report that he still has 10% of capacity, when in fact it has a much lower value, and this causes the computer to the unexpected shutdown.

  Cycles of discharge (or charge) are to use this charge battery (100%), but not necessarily all at once.

  For example, you can use the laptop for a few minutes in a day, using half of its e ability then it load completely. If you did the same thing the next day, it can be considered a discharge cycle, not two, so it may take several days before finishing a complete discharge cycle.

• I want to make my laptop plugged in, but do not load when the battery reaches 95%. How can I do?

  H !!!

  I want some help to train you...

  There are growing problem in many portable of peoples that their laptop shows connected but does not support...

  But it's not my problem.

  My problem is just the opposite of it.

  I want to make my laptop plugged in but not in charge when the battery reaches 95% how can that I do?

  Hoping answers from you...........................................................................................................

  Original title: Performance and tools

  JNMilan,

  It is not possible. You must use a third-party software to do or contact the manufacturer.

  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Back to us for any problem related to Windows in the future.

• Satellite L850-150 will stop even if the battery is charged

  Good evening

  Since I've upgraded to Windows 10, the following occur:

  The laptop battery stops unexpectedly without warning the minimum level, even if the battery is charged
  I bought a new battery and it is exactly the same as the previous battery

  What can happen?

  Best regards and thank you

  More details
  The first OS is Windows 7
  I created two partitions
  In the second partition, I installed Windows 8
  After awhile, I installed Windows 10 on Windows 7 and also installed 10 Windows on the partition of Windows 8
  In the two bulkheads made
  The computer turns off when you do not have the power cord plugged
  Earlier in Windows 7 and Windows 8, it did not
  Help, please

• [Z510] Problems with the battery not charging

  I have ideapad z510 for almost a year. and now my unit still shows that it is at 0% battery. and she indicates that she battery level does not increase. and for this reason I could not use my unit when it is not plugged. What should I do about it?

  Comment to Moderator: New thread is created. The topic is edited to include the model.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Beep is annoying when the battery is at 10% Y650

  It listed essentially the same question in the thread Y550 (http://forums.lenovo.com/t5/IdeaPad-Y-and-U-series-Laptops/Y550P-Low-Battery-Beep/m-p/200159#M18937)

  After reaching the remaining 10%, the battery starts beeping each about 10 seconds until you plug in an AC adapter.

  A BIOS version to stop the beep would be appreciated. As my laptop starts beeping when I'm in class and which is not good.

  Thank you

  Bryant

  Hi all

  I'm sorry for the late reply. I was not around when the new biox was released last week.

  Anyway, you will find the links here for download.

  32-bit Win XP, Win Vista, Win 7 - 15CN35WW (V2.08_x32) .exe

  64-bit win Vista, Win 7 - 15CN35WW (V2.08_x64) .exe

  Your trouble of having to beep when the battery is low should be fixed now. =)

  Thank you for your patience.

  Kind regards

  Cleo

• When the computer starts, it reads configuration updates 1 3-0%; not updated since 12.8.09, showing 8070002 error

  When the computer starts, it reads configuration updates 1 3-0%, but it continues
  Latest Windows Update 12.8.09; do not update since 12.8.09
  Display of error code 8070002.
  Mechanic charged and removed the registry and advanced system care3

  Hello

  Windows Update Error 80070002http://windowshelp.microsoft.com/Windows/en-us/help/c5f4d9e0-3eb6-426b-8118-0cedf489a75f1033.mspx#EJH

  Fix Error 80070002 when using Windows Update in Vista
  http://www.mydigitallife.info/2007/12/21/fix-Error-80070002-when-using-Windows-Update-in-Vista/
  Error Code 0 × 80070002 during Windows Vista SP1 Setup Install - SP2 might have similar problem
  http://www.tipandtrick.NET/2008/error-code-0x80070002-during-Windows-Vista-SP1-Setup-install/

  ------------------------------------------------

  Check the above and you may need to use these methods to interrupt the cycle.

  I guess that part of the question could be a driver which is really old or similar should not be loaded.

  This exit Windows updates on (after you have access) and stop the updates of the driver to load.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ---------------------------------------------------

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista with the Windows installation media and use the repair feature

  How to do a startup repair in Vista
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a Vista disk.

  Method 3: Rename the Pending.xml file, and then change the registry (this method is part of the advanced troubleshooting)

  See article below for that.

  You can use this method on the updates that have this problem.
  http://support.Microsoft.com/kb/949358

  Hide the update (click right - HIDE in the updates of Windows) and go to the Microsoft Download Center to download
  and install it.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• Fuze 4 GB warning disconnect and reconnect to Windows 7 pc... when the battery is low.

  So I just got a rocket and I love it.  Done a good deal about it.  Windows 7 picked it up and transfer of music is not a problem when the unit is fully charged.

  What IS a problem, is that when the battery is low and I have to plug the "rocket" on my PC to load... it keeps connection / disconnection.  The program of control of rocket guard Center popping up and go, arise and disappear... frustrating.  I tried the DPW and MCP modes (actually in DMC mode on the control panel is not everything and it does not recognize that the device is connected).  I've tried different USB ports.  No hub at issue here.

  Here's the kicker... If I load the "rocket" first (plug into a USB Kindle charger), once it has loaded it connects very well.

  Ran the update of the firmware and I'm on the latest firmware it was available, 1.02.31.

  I would like to know how to solve this problem, because I don't always have the small USB Kindle charger with me, and that would well be load from a PC... which is what the original, right intention was?

  Except that I like it and really dig the FM radio tuner.  It is very bad!

  Hosers, all.

  Usb hub 4 ports powered solved my problem.  'duh, I think yer cable is bad' I DO NOT.  Apparently, the "rocket" sucks just too much power.

  So I solved my problem with a $ 5 usb hub.  Yippee.