When the computer starts, it reads configuration updates 1 3-0%; not updated since 12.8.09, showing 8070002 error

Similar Questions

• How can I configure numerical Lock ON when the computer starts?

  I have a new laptop HP G70.  In the User Guide HP G70 on keyboards - C01540939.pdf, paragraph 3 using keyboards & pointing devices, Page 8 there is a note "the function of the keyboard that is active when the computer is turned off is restored when the computer turns on.   This does not work on my computer HP G70.  It always starts up the number Lock OFF.   How can I configure my computer to set the digit Lock ON when the computer starts?  I always use the number keypad and never use page up/down - button on top/bottom/right/lelt arrow.

  Also, how can I configure my computer to set the touch mouse on the computer OFF for the start.  I always use an external mouse.

  Any help would be appreciated.  It is a simple thing, but the present operation HP G70 is most annoying.

  PLEASE DO NOT CONTINUE TO MEET THIS PROBLEM!

  THE HP G70 WAS FAULTY!   EACH HP G70 HAS THIS PROBLEM!

  HP REPLACED MY HP G70 WITH a HPdv7.  THE HPdv7 PERFORMED THE DESCRIBER NERMAU LOCK FUNCTION AS IN THE HP INCTRUCTIONS.

  .
  
  Bob_in_PGI

  I'm surprised that nobody knows how to set the Num Lock at startup before you connect.  Where is the help of HP?

  I now have Windows 7 64 bit.

  There must be someone who knows how to do this.

  Bob in PGI

• When the computer starts first to the top, a window titled "run as" the question "which user account do you want to use to run this program?

  Original title: which user account you want to use to run this program?

  I use a computer that is running Windows XP SP3. Recently, when the computer starts first to the top, a window will appear titled ' run as ' the question "which user account do you want to use to run this program?" with two radio buttons. The default selection is "Current user" and there is a checkbox to "protect my computer and data from unauthorized program activity. The other button is for "the next user. I have to click 'OK' before you can run any programs.

  There is only one user on the computer. Why has this window began to appear and can I get rid of him?

  Hello

  That you recently installed which triggers this popup message initially upwards?

  You can try to perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to configure Windows XP to start in a "clean boot" State

  Note: Make sure that you put the computer to a Normal startup once you have completed troubleshooting.

• Software HP C4380 printer causes delays when the computer starts.

  I don't know what triggered the problem. I had unplugged the printer and reinstalled. Now, when the computer starts, it hangs for 2-3 minutes seeking a device to the USB location 0. That remove the HP software solves the problem. I installed with the latest HP drivers and tried to use only the printer drivers without the scanner software. If I avoids the HP software, Windows installs with a Jungo win driver that causes the same result. It could have been an update of my Windows XP Home SP3 in the meantime I demolished the printer and reinstalled, but I can't follow any other changes.

  Now the printer is useless because of this problem. HP forums suggested disabling a program of tracking of HP under Services.msc, but who has also failed to solve the problem. Any suggestions?

  check the clean boot state, this might help you http://support.microsoft.com/kb/929135

• Node Manager does not restart the WebLogic servers when the computer starts

  Hi all
  
  I'm testing the new WebLogic Server version as well as of new forms and reports. I don't have much experience with WebLogic (using the Internet Oracle 10g Application) bare with me for a moment.
  
  I'm using Node Manager to start admin server and all the other managed servers. I also installed nodes as a Windows service manager and configured the boot parameters to include Xrs-/-Xnohup, as stated in the documentation and everything seems to work fine until I restart the server. Node Manager service starts and according to his diary, he plays startup.properties of each server, but it does not start them. Am I missing something here? I found myself in an impression that Node Manager must restart the server in case of reboot system, if the server was running when the computer has been restarted.
  Even though I don't have much experience with WebLogic, I'm not a beginner. I managed to migrate (for testing only) all the business application (more than 1000 forms and reports) of iAS 10g to the new version in two days. Application works very well and I only have problems with servers to start when the computer starts using Node Manager.
  
  Test environment:
  Windows 2008 Standard 32-bit
  RAM: 2 GB
  HARD DRIVE: THE 140 GB
  CPU: 2xXeon

  # nodemanager.properties
  ...
  CrashRecoveryEnabled = true
  ...

• How to remove temporary files, waiting to be written to disk when the computer starts? __

  How to remove temporary files, waiting to be written to disk when the computer starts?

  Hi Reasman,

  Welcome to the Microsoft answers site!

  To clear pending files, select the files/folders in the 'Files to add to the CD/DVD' box and press DELETE. However, if you want to delete all files, click the CD/DVD drive and select 'Clear the staging area' from the context menu.

  You can manually delete the files that are stored in the following location:

  %USERPROFILE%\Local Settings\Application Data\Microsoft\CD Burning folder

  I hope this helps!

  Kind regards
  Gokul - Microsoft Support

• I get an error message when the computer starts, "failed to prepare the critical file! Engine out of Chameleon.

  I have a laptop Asus N53Jq, 16 GB, 224 GB ssd, I get an error message when the computer starts, "failed to prepare the critical file! Engine out of Chameleon"when I click the computer works fine, but it seems that she was taking more resources without doing me anything. Do know how to solve this problem.

  Original title: Chameleon engine

  I uninstalled ASUS Splendid Video Enhancement Technology to my computer and it solved the problem!

• Windows Defender will stop when the computer starts

  Windows Defender goes off when the computer is started and occasionally when the computer is running. I bring up the Control Panel icon, click on restart and restart the program. I had this problem for a week but have not added new software for a fortnight. Everything ran happily until a week ago. I am running Windows Vista Home Basic on a Packard Bell Imedia 3312 UK computer, purchased in April 2009

  Are you by chance using AVG 9.0 for your antivirus package? This version of AVG 9 automatically extinguished Windows Defender. Microsoft® Security MVP, 2004-2009

• CD/dvd drive does not work - it is recognized when the computer starts, and it is listed in the Device Manager?

  I am running Vista Home Premium on a laptop Compaq Presario F700. It is listed in the list of computers of readers, it is listed in Device Manager. The lites drive that the computer boots so I know it is detected. When you run itunes or media player the player does not open. When I push the drive button it will not open. It opens with a paperclip in the exit hole. It cannot read a CD or a DVD. None of the media players even recognize there is a disc in the drive. I tried to run fixit, but it would not drive either. I tried restoring from a previous backup, without change.

  Hello

  Check / settings (BIOS/CMOS) often F2 so watch the screen as it starts - place CD/DVD
  1st in the boot order (remember to put it at the time where the fact).

  Then put in a DVD to boot Windows and see if the driver works.

  If it doesn't then it's a hardware problem.

  =======================================

  If the drive has worked in the test above, that these can help:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• asks to reinstall hpzjrdoi.dll when the computer starts?

  How to install this to get rid of it, when I start computer. Do I need this on my computer. How can I get rid of it if I do not need. Thank you, Charles Harrison
  Operating system: Windows XP

  It is always sensible in this situation to achieve a malware check

  Start the computer in safe mode with network and download and install Malwarebytes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.
  http://www.precisesecurity.com/how-to/HT-smodewnet.htm
  http://www.Malwarebytes.org/products/malwarebytes_free

  Download and run SuperAntiSpyware (Free Edition)
  http://www.SUPERAntiSpyware.com/download.html

• Administrator account appear in the logon screen when the computer starts in normal mode, and there is also another account on the computer.

  I use Windows XP. I start my computer and I see an administrator account on the logon screen. I wonder why this account appears. I checked in the Help Center and he said that this account do not appear when I start Windows Mode without failure or when no other account does seem to accept the guest account. But after all, I never start Windows Mode safe and I also have another account on this computer. So why do this administrator account appear and how to hide? I thank.

  Hello

  ·         You are the administrator of the computer?

  You can read the following article to disable the administrator account. You must be logged in an admin account to do this.

  How to disable the Local Administrator account in Windows

• Windows does not work when the computer starts in mode 'sleep'

  The computer is easily adjustable in standby mode when I press on the eve of my keyboard key. However, when I want to start the computer again via push any key, the screen never shows anything (just fill black and nothing can be seen). Indicators power will return to the pilot and solid seems also lit, but just nothing display on screen. I have to push the power to shut down the computer completely to restart again.

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.HTML?filter [11] = power % 20Management

  Read the info in the link above and in the "related links", including this one:

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  See you soon.

  Mick Murphy - Microsoft partner

• Windows 7: no start button or taskbar when the computer starts

  Original title: Black screen and the taskbar and the start to the Start button

  At the start, I had a black screen with no tasks or start bar button. Just the pointer and remote area was visible. (I have a dial-up connection and sometimes when I start remote poster on his own area right after the desktop). I could not access the boot menu. I don't know how he has become black because I left after that I turned on the computer. I pressed the power button. When I did I got the light blue screen that says it would close down and he stopped normally. When I rebooted I had no problem and he has not done since.

  I not made any changes to the computer except change the desktop wallpaper several times for a long time.

  Can someone tell me what is the problem with my computer so I can fix it so this or something worse will happen?

  Thank you

  Hello misha38,

  After proofreading by the wire, it looks more like a hardware/driver problem. Have you tried updating your video driver from your computer manufacturers Web site? Please visit the website of the manufacturer of your computer to locate and install the correct driver.

  Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• FF opens without me it starts when the computer starts with unwanted Bing or tabs tab

  When I start my computer, sometimes FF starts by itself and there are tabs Bing 1 or no longer desired. It seems to occur only when the date has been changed, never for a second time on the same date. Please answer in simple and plain English.
  Thank you
  Bernadine

  
  

• HP 8620: Printer in offline mode when the computer starts

  My 8620 Officejet is offline.  It is connected via a cable to my 360 spectrum HP network.  When I turned off the computer and start that he even once, the printer starts in offline mode - for example, when I got to print from Microsoft Word (Office Pro 2016), the printer is 'offline' in the Word print dialog and I get a message from Windows system, saying printer offline - and nothing prints.

  I can solve it with the help of HP print and Scan doctor.  But if I closed the computer and start it up again, it is new offline.

  I can fix this by going to the printer by pressing the button on the front power off and then restarting it - the document in the print queue print immediately.

  Also, if I start the Server Web part, select 'Tools' and then click 'Print a self Test Page', the page prints as usual. However, if I then go back to Microsoft Word, the printer remains offline.

  HP Printer Wizard starts well and the analysis of function of Document or Photo works very well.

  It's just the feeling that is not.

  Any ideas gratefully received.

  Thank you
  Philippe

  Hi @Philip4,

  Welcome to the HP Forums!

  I noticed that your HP Officejet Pro 8620 keeps going offline. I'm happy to help you!

  Please, try the steps in this guide, "offline" Status Message printer (Windows 10), as well as this guide, the printer is not maintaining the wireless connection.

  If this, or one of the posts on this thread, helped you to solve the problem, please click on accept as Solution on the message. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

  I hope these guides help!