Tecra M3 (PTM30E) - new module of memory not recognized

Similar Questions

• Satellite L500 - second module of memory not recognized

  Have installed 2 GB Offtek extra memory in 2nd slot of memory, but it is not recognized by the system--still show only 2 GB installed memory.

  What is the problem?

  Hey,.

  I've never heard of RAM modules Offtek

  From my own experience, I can say that work really well Kingston memory module and never had a problem with them, they are of high quality modules.

  In my opinion, you should try a different RAM module. Maybe it s is not compatible, so it will not be recognized that s my personal opinion.

• New Ipod nano is not recognized on laptop

  Bought a new Ipod Nano (my old one fell; broken screen).  I have the latest version of ITunes on my laptop HP Envy.  My sync iPhone without any problem. my old ipod nano also syncs.  A did the device synchronization Tests. Results: No Ipod Touch, IPhone or Ipad found.  I can also scroll to the clock and the parameters of the IPod Nano. I need help from the community before I call Apple.  Thank you

  Hello pamelafromsonora,

  Thank you for using communities of Apple Support.

  According to your post, I see that your new iPod nano is not recognized by iTunes on your Windows PC, and you cannot scroll through the settings of the clock on your iPod. I know how it is important to ensure that you can connect your iPod to your computer/iTunes and use all the features. I'll be more than happy to help you with this.

  Use the article If iTunes does not your iPad, iPhone or iPod and follow these steps to see if iTunes recognizes the device, specifically these sections:

  When iTunes on your computer doesn't recognize not the connected device, follow these steps. Try again after each step:

  1. Make sure that you have the latest version of iTunes that works with your computer.
  2. Check that you have the latest version of the software on your Mac or your Windows PC.
  3. Make sure that your device is turned on.
  4. If you see a trust this computer alert, unlock your device and press trust. If you still see the alert, you may need to reset your lockdown folder.
  5. Unplug all accessories USB from your computer except for your device. Try every USB port to see if it works. Then try another USB Apple cable.
  6. Restart your computer and your iPhone, iPad or iPod.
  7. To see if your device needs service, try another computer. If you have the same problem again, contact The Apple support.

  If you are using a Windows PC

  1. Open Device Manager by following the steps for the version of Windows that you have:
     • Windows 10: Click the search box in the lower left corner, type Device Manager and press ENTER. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
     • Windows 8: loose in the right edge of the screen. Press search and enter the Manager devices, and then click Device Manager. If requested, enter your password. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
     • Windows 7: click on > Control Panel > system and Maintenance > Device Manager. If requested, enter your password. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
  2. Even if you do not find the Apple driver, follow the steps below, based on what you see or don't see.

  The pilot and
  No symbols

  A down arrow
  by the driver

  Exclamation or
  question mark by
  the pilot

  No Apple Mobile
  USB device driver

  You don't see symbols next to the Apple Mobile Device USB Driver

  If you do not see , , or of the Apple Mobile Device USB Driver, look for third-party software conflicts. Then if you still need help, restart your Apple Mobile Device Service or contact Apple technical support.

  

  You see an arrow down

  If you see next to the Apple Mobile Device USB Driver, the driver with the right mouse button and choose enable from the context menu. Then if you still need help, contact contact Apple technical support.

  

  You see an exclamation point or question mark

  If you see or the Apple Mobile Device USB Driver, right click on the entry, then manually update the Apple Mobile Device USB driver.

  

  You do not see the Apple Mobile Device USB Driver

  1. Disconnect your device from your computer.
  2. Save a screenshot by pressing the Home button and sleep/wake button of the device button at the same time. The screen should Flash briefly.
  3. Reconnect your device to your computer.
  4. If you see one of these sections in the Device Manager, expand them:
     • Imaging devices
     • Other devices
     • Portable devices
     • USB Bus controllers

  Now, locate the entry that recognizes the device as a camera. You should see 'Apple IPhone', 'Apple iPad' or 'Apple iPod '. Right-click the device entry, and then manually update the Apple Mobile Device USB driver.

  If a single unknown device appears, follow these steps:

  1. Right click on the unknown device entry.
  2. Choose Properties from the context menu, and then click the Details tab.
  3. In the drop-down menu, select hardware IDS.
  4. If the ID begins with something other than USB\VID_0000 & PID_0000, go into the Device Manager and right click on the entry for device unknown, and then manually update the Apple Mobile Device USB driver.
  5. If the ID begins with USB\VID_0000 & PID_0000, then follow the remaining steps.
  6. Unplug the unit and remove all the USB devices on the computer.
  7. Shut down the computer, and then turn it back on.
  8. Reconnect the device, tests of each USB port for about 30 seconds to see if the device is recognized.
  9. Test with a different, checked 30-pins-USB or the lightning-connector-cable-USB, if they are available.

  If you still need help, contact Apple technical support.

  

  Manually update the Apple Mobile Device USB driver

  If one of the sections above directs you to this section, you should already have right click on an entry in the Device Manager. Now, follow these steps:

  1. Choose update driver software.
  2. Choose "Browse my computer for driver software."
  3. Choose "Let Me pick from a list of drivers for devices on my computer.
     
  4. Click the disk button. If this is not available, choose a category of devices such as Mobile phone or storage device, if in the list.
  5. Click Next. You should see the disk button.
  6. Click Browse and navigate to C:\Program Files\Common Apple Mobile Device Support\Drivers.
  7. Double-click the file "usbaapl. If you have a 64-bit version of Windows, this file will be called "usbaapl64". If you do not see here "usbaapl64" is not a Drivers folder, look in C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers.
  8. In the disc window, click Open, and then click Next and then click Finish.
  9. Windows installs the driver. If a message indicates that the software that you install "not passed the Windows Logo test", click on continue. You can get help with other common errors and the error code numbers in this Microsoft article.
  10. Open iTunes to make sure that iTunes recognizes your device. If not, Restart the Apple Mobile Device Service.

  Best regards.

• D5 MkIII will import, but new PowerShot G9X is not recognized?

  D5 MkIII will import, but new PowerShot G9X is not recognized?

  Devices supported by Adobe Camera Raw

  The G9X was initially supported by Lightroom 6.3.

  What version do you use?

• Satellite A100-828 - new module of memory does not

  Hello

  I recently bought 2x2gb modules for my A100-828. However, I can not any memory module to adapt to the second extension slot. I tried both the new modules in it that the old module of 512 MB which was originally in the laptop. The new memory is certainly compatible as two new modules work in the first expansion slot.

  Memory does not seem to fit properly in the second slot (I put in a good sense ad. it won't push back.)

  Anyone have ideas, what is the problem?

  Thanks for your help.

  Hello

  I put t know why do not the module in the second slot.
  The two sites are completely identical and also support the same standard.

  I think you used it just not compatible modules, or you have tried inserting modules backwards
  AFAIK you need DDR2 667 MHz (* PC2-5300 *) module SODIMM 200 PIN.

  What module do you use?

• Why my Satellite does not detect a new module of memory?

  Hello

  Today, I installed a new memory module SDRAM 128 MB in my Satellite 1670. It is not a real module but on the package is the right code: PA3005U.
  After that I turned on the computer, it is not detected then I use still 32 MB of RAM.
  How can I solve this problem?

  Steef

  Hello

  The fact is that you use the right memory module. It is not easy to say why the new module is not recognized correctly. The slot is maybe defective. Try to remove 32 MB module and use any other location 1. (Unfortunately I put t know if this device has two or one single location for memory expansion).

• Satellite L300-229 - new module of memory is not recognized

  Satellite L300-229 - I just installed an extension of memory of 1 GB to add to the existing 1 GB.

  I used a 1 GB Crucial 200pin DDR2 SODIMM PC2 6400 CL6. For some reason, it will not recognize it and shows again that the 1 GB. I closed and installed in start mode according to manual and tried to reinstall.

  Any idea?

  Thank you

  Hello

  What happens if you only install the new module 1 GB RAM? Don't start the computer and if so how much RAM does show?

  Normally, the specifications of the new RAM module should work. I have a Satellite L300 too and I've updated it with the same RAM but Kingston. It works without any problem. :)

• New HARD drive is not recognized on Tecra M1

  Hello

  I am new to this forum, so apologies if this is an old question.

  My Tecra M1 gave a quality service for the past 6 years, but recently, the Toshiba management console has put a message saying that the HARD drive will fail quickly.

  I loaded immediately turned off my main files before you remove the HARD drive. It is a Toshiba MK6022gax 60 gig IDE hard drive. I bought a new disc of gigabytes of 60 MK6022gax, but when I mounted this same I got the error message "error ide #0". Installation XP or the BIOS can see this new record.

  I then reassembled the old HARD drive, which started OK. I then mounted the new disk in a USB enclosure, initialized, partitioned and quick formatted using the XP disk management. He picked up OK. Then I copied some files to it and read them back with no problems, then the drive itself works very well. But when I plug as the main 'C' drive, I get the error message again and is not recognized by the bios or XP put in place.

  Clearly, there is some BIOS (?) or startup procedure I have to do to get this recognized record. Help!

  I have Tecra M1 long with 60 GB HARD drive. Right now, I've updated compatible HDD TOSHIBA HDD 2184 B.
  I can confirm that the HARD drive is recognized correctly and I actually have the new install of WXP Pro.

  In any case, have you tried to upgrade the BIOS to the default settings?
  As far as I know that nothing should be set before you put the new HARD drive and it must be recognized correctly.

• Satellite L30 - 11 d doesn't start after the addition of a new module of memory

  I mounted a second chip memory in a Satellite L30 - 11 d, but windows does not start at the top. If I take one or the other exit, then it will start

  I looked at the specs for this computer, and it is said, there are 2 slots for memory, 1 to configure

  But it's my problem, and how to configure it?
  Thanks in advance

  Bobandsue

  Hello

  The phone supports 2 slots of memory, but we were already occupied.
  As far as I know one installed the module of memory was 512 MB DDR2 (533 MHz)

  I think your laptop doesn t boot because the second module is simply not compatible or it s defective!

  You can upgrade the laptop up to 2 GB DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM modules should be used.

  Good bye

• Compaq Presario SR5010NX: One of the two locations of memory not recognized / work

  Had already upgraded RAM from 512 to 1 GB.  In an attempt to level again with a 2nd (identical to the first) 1 GB DDR2 DIMMS, I discovered that the 2nd module of memory was not being recognized.  I also tried with success the new! G in the first taken.  Specification to support up to 2 GB with 1 GB DDR2 DIMMS in each shot. However, "no beeps" and not "start with anything in the second taken.   I also tried two 256 KB RAM modules and as the two 1Gs only the a 256 KB has been recognized.

  I also tried to boot with a module in the 2nd outlet only and found that my system wouldn't start.  Any suggestion would be appreciated.

  C001uS

  Thanks again for your response.  I went not the CMOS battery. However, your answer made me look on a possible revision of the BIOS through HP customer care.  I downloaded the version of BIOS the same but with a more recent date.

  After download and install I shut down my computer, insert the 2nd module of 1 G and made a new shoe.

  Happiness is a system of 2 GB Dual Channel now running.

  PROBLEM SOLVED

• Tecra M9-185 - 750 GB HARD drive not recognized

  I have Tecra M9-185 (PTM91E-0G4045G3) with BIOS Version 1.90 dated the 29.02.2008.
  It came with HARD drive of 160 GB, which is quite old and needs replacement. I want to upgrade the HARD drive. I tried to use the 750 GB HARD drive, but it was not recognized by the BIOS.

  Is it possible to upgrade the HARD disk? Is there a limit to the ability of the new HARD disk that can be installed?

  Hello

  Of course, the HARD drive can be upgraded.
  The laptop supports the SATA controller. The SATA controller is not limited to a special HARD drive size of my knowledge. 750Go should be supported too. But it might be possible that the BIOS is not able to manage these dimensions.
  Try a different SATA HDD with the smaller size.

  But question: why you n t choose an SSD (250 GB)?
  I have improved my Tecra A10 with a 250 GB SSD and the performance gain is amazing. The machine is running much faster and quieter

• upgrade memory not recognized

  I have a pavilion dv6405ca that came with 2 512 memory sticks. I replaced them with 2 1gig sticks and all thing as before, but the computer works is still only 1 ram total concert. The bios won't let me change anything, but the date and time and memory remapping is not on the menu.  the operating system is vista Home premium.

  Oh... I have flashed the bios to f.42 f.43. no problems, but the machine is still unaware of the increased ram.

  RESOLVED the 2nd slot was not properly seated new stick. The old man sat down with a problem, but the new ram RAM has not quite contact (about 8 times in a row!). I finally noticed and made a misguided pushing and he sat and I have my complete 2gig. Thank you for you time and effort.

• Re: New DVD player is not recognized - Satellite 5200 801

  The old DVD drive no longer works, so I bought a new DVD player (SonyNEC Optiarc AD - 7593A).
  But the system does not recognize the new drive at all.

  I can not boot from the CD and in the hardwaremanager, there is no CD/DVD.

  But the drive works. If I put a CD in, you can hear how he turns upward.
  If I put the old drive, it is recognized in the hardwaremanager, but the reader no longer works.

  Any ideas?

  Thank you
  FO

  > But the drive works. If I put a CD in, you can hear how he turns upward.

  It says nothing! You can hear the rotating disc because it s connected to the laptop and it s operated.

  The BIOS is important! Your new CD/DVD drive is recognized in the BIOS?

  If not, then you have purchased NOT compatible CD/DVD player!

  I think that the master/slave/c-salt settings are not compatible with the laptop and so the CD/DVD drive may not be recognized.

• Tecra M3 and Advanced Port Replicator III: not recognized as docking station

  Hello!

  Just install my new M3 and Advanced Port Replicator III. Everything works fine, but the Port Replicator is not recognized as a Docking Station (No disconnect in menu button start XP; pressing disconnect button on the Port Replicator itself has no effect either).

  Is TI WHEREAS behavior?
  Thank you in advance.

  Hello

  You reinstall the unit with the recovery CD?
  As far as I know that the TOSHIBA Mobile Extension3 for Windows XP is responsible for the good condition of the market of the docking station.
  Well, I recommend to reinstall this driver and utility.
  Perhaps the installation of the new driver will solve this problem.

  Good bye

• Memory not recognized for computer laptop dv5020

  Laptop older specifies 2 GB max memory, but when I install 2 GB (1 x 1 modules) it will only recognize 1 GB.  A scanner memory shows one of the RAM slots is empty even when I swap modules.  I was wondering if there was a configuration switch that I would need to change if she recognizes the two slots?  Both are full, but we show that it is empty.

  The system is 64 bit AMD running XP Home edition with Service Pack 3.

  Hello

  Remove 1 of your memory modules and check if it is recognized in slot 1 and slot 2 - try also with just one module of memory.  Each single module is recognized in each slot?

  It might be useful to reset the default settings of the bios as follows.

  Judgment of the laptop.  Tap here to f10 as soon as you start Notepad to open the menu of the bios.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Kind regards

  DP - K