Telnet/ssh/http remote access LWAP CLI

All the:

Is it possible to remotely connect to the wired interface to a LWAP?

Here is why I ask:

Passing 5508 controller (7.4.110.0) installation a colo to the subnet to another and changing controller in the process.

Can I use the cmd IOS: time "reload in X" or "recharge at X time" on the LWAPs?

Is there a better way to do what I didn't think?

About 120 LWAPs involved in a fairly large geographical area - time of 3 hours by car.

THX,

Phil

I guess the question of reading the post, is what you're doing? We assume you will the WLC to another subnet and the IP address will change. If this is the case, it depends on how comfortable you are with the command-line if you don't not WCS/NCS or the first to get templates.

In general, I would like to change the AP on AP to point primary school at the new address IP WLC, even if she is not yet up and enter the secondary WLC as one that is already in place. I did it with more than 200 AP if you would not do this, then the easiest is just to use DNS and resolve cisco-capwap-controller. the new IP address of the WLC. You can use option 43, but you must assign this right. Once your APs is moved, then I usually remove the DNS and option 43 if I put those.

Sent by Cisco Support technique iPhone App

Tags: Cisco Wireless

Similar Questions

Unable to SSH/telnet through the remote access VPN to ASA interface

Hi all - im trying to SSH/telnet to my ASA in my remote access VPN tunnel but

can't get this to work. what Miss me?

remote access VPN subnet: 192.168.25.0

LAN subnet: 192.168.1.0

config is attached. THX-

Please enter the command

Private access Managament

and you will be able to telnet/ssh to the asa on this ip 192.168.1.253

install the Telnet Service for remote access

How do we install the telnet service on my pc I can access the pc from anywhere under the same gateway.

Reach

beginning

Run

Type "services.msc".

find and start the telnet service, and set the startup type to automatic

Now you set any password for your administrator account?

If not now

go to my computer > right click > manage

find user and group > select Administrator > right click > set password

now go into firewall of network properties, made setting a right click on the network adapter Firewall setting and allow the exception to add 23 like telnet port name

and you're done

Restart your system

Hope this work

Best regards and good luck

Sohail Khan

PIX telnet/ssh access to the VPN Lan2Lan

Scenario of several Lan - Lan IPSEC VPN between PIX F/Ws.

I need to remotely access / these PIX via Telnet/SSH & would prefer to do it through the VPN tunnel.

NB, I tried telnet/ssh configuration for both inside/outside of my source but can't hit the PIX.

Because the Tunnel is actually inside-inside I'm trying to connect to the inside interface of the pIX.

You can do it now in 6.3 code with the command "access management". See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/mr.htm#1137951 for more details.

Change of SG 200-18 - management - VLAN / telnet/ssh-access?

Hello

We have a switch SG200-18 that should be used as a switch of working group in our environment (SW

Version 1.1.1.8). In collaboration with CLI on big and mid range Cisco gear during the past two decades, I have a hard time to understand what follows on the SG200:

(o) I want to change the management VLAN by default '1' to the management - VLAN used in our environment. Of course, I created this vlan in SG200-config, however when it comes to assign the management IP and VLAN management interface in the advancement of the corresponding film under "Interface IPv4-> management VLAN" selectable is the default "1". see screenshots (closed)

So, how to define a management VLAN 1 different?

(o) how to enable telnet/ssh-access the SG200-18 - I'd be much more comfortable with a CLI environment ;-)

Thank you very much in advance for your help,.

-ewald

Hello Ewald,

Sx200 series switch does not currently offer a CLI option. Have this feature if the Sx300 and 500 series.

What about chaning the vlan management, you have two options.

(1) changes the vlan by default under management VLAN > Default vlan settings. This will change all the ports and the management vlan.

(2) adds a port as a port untagged in the new VLAN. Once this is done, make sure that something is connected to this port, like a computer. Now you should be able to change the vlan management. (This is done to prevent locking)

Create different group with VPN remote access

Hello world

The last time, I ve put in place a VPN for remote access to my network with ASA 5510

I ve access to all my internal LAn helped with my VPN

But I want to set up a vpn group in the CLI for a different group of the user who accesses the different server or a different network on my local network.

Example: computer group - access to 10.70.5.X network

Group consultant network - access to 10.70.10.X

I need to know how I can do this, and if you can give me some example script to complete this

Here is my configuration:

ASA Version 8.0 (2)
!
ASA-Vidrul host name
vidrul domain name - ao.com
activate 8Ry2YjIyt7RRXU24 encrypted password
names of
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
address IP X.X.X.X 255.255.255.X
!
interface Ethernet0/1
nameif inside
security-level 100
address IP X.X.X.X 255.255.255.X
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Description Port_Device_Management
nameif management
security-level 99
address IP X.X.X.X 255.255.255.X
management only
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
DNS server-group DefaultDNS
vidrul domain name - ao.com
access-list 100 scope ip allow a whole
access-list extended 100 permit icmp any any echo
access-list extended 100 permit icmp any any echo response
vpn-vidrul_splitTunnelAcl permit 10.70.1.0 access list standard 255.255.255.0
vpn-vidrul_splitTunnelAcl permit 10.70.99.0 access list standard 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 10.70.255.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
MTU 1500 management
IP local pool clientvpngroup 10.70.255.100 - 10.70.255.200 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 602.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 10.70.0.0 255.255.0.0
Access-group 100 in the interface inside
Access-group 100 interface inside

Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
Protocol RADIUS AAA-server 10.70.99.10
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
Enable http server
http 192.168.1.2 255.255.255.255 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
Telnet 0.0.0.0 0.0.0.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
outside access management
dhcpd manage 192.168.1.2 - 192.168.1.5
dhcpd enable management
!
a basic threat threat detection
Statistics-list of access threat detection
!
class-map inspection_default
match default-inspection-traffic
block-url-class of the class-map
class-map imblock
match any
class-map P2P
game port tcp eq www
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
Policy-map IM_P2P
class imblock
class P2P
!
global service-policy global_policy
vpn-vidrul group policy internal
vpn-vidrul group policy attributes
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
value by default-field vidrul - ao.com
test 274Y4GRAbNElaCoV of encrypted password privilege 0 username
username admin privilege 15 encrypted password bTpUzgLxalekyhxQ
attributes of user admin name
Strategy-Group-VPN-vpn-vidrul
username, password suporte zjQEaX/fm0NjEp4k encrypted privilege 15
type tunnel-group vidrul-vpn remote access
vpn-vidrul general-attributes tunnel-group
address clientvpngroup pool
Group Policy - by default-vpn-vidrul
IPSec-vpn-vidrul tunnel group attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:d84e64c87cc5b263c84567e22400591c
: end

What you need to configure is to imitate the configuration on the tunnel-group and group strategy and to configure access to specific network you need.

Currently, you have configured the following:

vpn-vidrul group policy internal
vpn-vidrul group policy attributes
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
value by default-field vidrul - ao.com

type tunnel-group vidrul-vpn remote access
vpn-vidrul general-attributes tunnel-group
address clientvpngroup pool
Group Policy - by default-vpn-vidrul
IPSec-vpn-vidrul tunnel group attributes
pre-shared-key *.

What you need is to create new group policy and the new tunnel-group and configure the tunnel split ACL to allow access to specific access required.

The user must then connect with the new group name and the new pre-shared key (password).

Hope that helps.

Configuring remote access VPN

Hi all

I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.

This is the configuration I have:

VPNROUT #sho run
Building configuration...

Current configuration: 6832 bytes
!
! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VPNROUT
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login userauthen1 local
AAA authorization groupauthor1 LAN
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-1632305899
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1632305899
revocation checking no
rsakeypair TP-self-signed-1632305899
!
!
TP-self-signed-1632305899 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
854A61E2 794F8EF5 DA535DCC B209DA
quit smoking
!
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 172.20.0.1 172.20.0.50
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp pool 1
network 172.20.0.0 255.255.240.0
domain meogl.net
router by default - 172.20.0.1
172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
8 rental
!
!
!
no ip domain search
IP domain name meogl.net
name of the IP-server 172.20.0.4
name of the IP-server 41.79.4.11
IP-server names 4.2.2.2
8.8.8.8 IP name-server
IP cef
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FCZ1804C3SL
!
!
username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group moweclients
XXXXXXX key
DNS 172.20.0.4
meogl.net field
pool mowepool
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
tunnel mode
!
!
!
Dynmap crypto dynamic-map 1
Set transform-set moweset
market arriere-route
!
!
card crypto client mowemap of authentication list userauthen1
card crypto isakmp authorization list groupauthor1 mowemap
client configuration address card crypto mowemap answer
mowemap 1 card crypto ipsec-isakmp dynamic dynmap
!
!
!
!
!
interface Loopback0
IP 172.30.30.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 100
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
IP 41.7.8.13 255.255.255.252
NAT outside IP
IP virtual-reassembly in
intellectual property policy map route VPN-CLIENT
Shutdown
automatic duplex
automatic speed
mowemap card crypto
!
interface Vlan1
Description $ETH_LAN$
IP 10.10.10.1 255.255.255.248
IP tcp adjust-mss 1452
!
interface Vlan100
IP 172.20.0.1 255.255.240.0
IP nat inside
IP virtual-reassembly in
!
local pool IP 192.168.1.1 mowepool 192.168.1.100
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source overload map route interface FastEthernet4 LAT
IP route 0.0.0.0 0.0.0.0 41.7.8.12
!
access-list 23 allow 10.10.10.0 0.0.0.7
access-list 23 allow 172.20.0.0 0.0.15.255
access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
access-list 144 allow ip 192.168.1.0 0.0.0.255 any
not run cdp
!
LAT route map permit 1
corresponds to the IP 100
IP 41.7.8.12 jump according to the value
!
route VPN-CLIENT map permit 1
corresponds to the IP 144
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
!
!
end

Please the configuration above, give me the desired output.

Thank you.

Hello Thomas,.

I'm glad to hear that you have found useful in the example configuration.

I checked your configuration and everything seems ok with him, especially the statements of nat.
```
 ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in 
```
Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:

-The router receives this traffic between VLAN100 unit?

-The router is encrypt this traffic, after receiving the ICMP packet?

#show crypto ipsec router its can help you with this question. Look for the program/decaps counters.

-The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.

The following document explains more this crypto commands and debugs if necessary.

http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/5409-IPSec-debug-00.html#iosdbgs

Remote access VPN users unable to see local lan or internet

We implement an ASA5510. Now our users can connect to the vpn but cannot access the internal Lan or internet.

Here is the config. Any help or idea would be greatly appreciated. Thank you

Cryptochecksum: dd11079f e4fe7597 4a8657ba 1e7b287f

: Saved
: Written by enable_15 at 11:04:57.005 UTC Wednesday, April 22, 2015
!
ASA Version 9.0 (3)
!
CP-ASA-TOR1 hostname
activate m.EmhnDT1BILmiAY encrypted password
names of
local pool CPRAVPN 10.10.60.1 - 10.10.60.40 255.255.255.0 IP mask
!
interface Ethernet0/0
nameif outside
security-level 0
IP 63.250.109.211 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
10.10.10.254 IP address 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
passive FTP mode
the local object of net network
10.10.10.0 subnet 255.255.255.0
net remote object network
10.10.1.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.10.10.0_24 object
10.10.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.10.60.0_26 object
255.255.255.192 subnet 10.10.60.0
Outside_1_cryptomap to access extended list ip 10.10.10.0 allow 255.255.255.0 net object / distance
CPRemoteVPN_splitTunnelAcl list standard access allowed 10.10.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-731 - 101.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) local static source net net-local destination static net distance net-distance
NAT (inside, outside) static source NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.60.0_26 NETWORK_OBJ_10.10.60.0_26 non-proxy-arp-search of route static destination
!
NAT (inside, outside) source after-service dynamic automatic one interface
Route outside 0.0.0.0 0.0.0.0 63.250.109.209 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 management
http 10.10.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 corresponds to the address Outside_1_cryptomap
card crypto Outside_map 1 set pfs Group1
card crypto Outside_map 1 set peer 209.171.34.91
card crypto Outside_map 1 set transform-set ESP-3DES-SHA ikev1
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal CPRemoteVPN group strategy
attributes of Group Policy CPRemoteVPN
Server DNS 10.10.10.12 value
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
value of Split-tunnel-network-list CPRemoteVPN_splitTunnelAcl
carepath.local value by default-field
Split-dns value carepath.ca
activate dns split-tunnel-all
no method of MSIE-proxy-proxy
the address value CPRAVPN pools
roys jjiV7E.dmZNdBlFQ encrypted password privilege 0 username
roys username attributes
VPN-group-policy CPRemoteVPN
tunnel-group 209.171.34.91 type ipsec-l2l
IPSec-attributes tunnel-group 209.171.34.91
IKEv1 pre-shared-key *.
type tunnel-group CPRemoteVPN remote access
attributes global-tunnel-group CPRemoteVPN
address CPRAVPN pool
Group Policy - by default-CPRemoteVPN
IPSec-attributes tunnel-group CPRemoteVPN
IKEv1 pre-shared-key *
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:dd11079fe4fe75974a8657ba1e7b287f

: end

Hello

A couple of things set this:

-crypto isakmp nat-traversal 20

-management-access inside

Can you run a packet tracer and attach it here, to see what are the phases that crosses the package.

David Castro,

Concerning

Client remote access VPN gets connected without access to the local network

: Saved

:

ASA 1.0000 Version 2

!

hostname COL-ASA-01

domain dr.test.net

turn on i/RAo1iZPOnp/BK7 encrypted password

i/RAo1iZPOnp/BK7 encrypted passwd

names of

!

interface GigabitEthernet0/0

nameif outside

security-level 0

IP 172.32.0.11 255.255.255.0

!

interface GigabitEthernet0/1

nameif inside

security-level 100

IP 192.9.200.126 255.255.255.0

!

interface GigabitEthernet0/2

Shutdown

No nameif

no level of security

no ip address

!

interface GigabitEthernet0/3

Shutdown

No nameif

no level of security

no ip address

!

interface GigabitEthernet0/4

Shutdown

No nameif

no level of security

no ip address

!

interface GigabitEthernet0/5

nameif failover

security-level 0

192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

!

interface Management0/0

nameif management

security-level 0

192.168.2.11 IP address 255.255.255.0

!

passive FTP mode

DNS server-group DefaultDNS

domain dr.test.net

network of the RAVPN object

192.168.0.0 subnet 255.255.255.0

network of the NETWORK_OBJ_192.168.200.0_24 object

192.168.200.0 subnet 255.255.255.0

network of the NETWORK_OBJ_192.9.200.0_24 object

192.9.200.0 subnet 255.255.255.0

the inside_network object-group network

object-network 192.9.200.0 255.255.255.0

external network object-group

host of the object-Network 172.32.0.25

Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

pager lines 24

management of MTU 1500

Outside 1500 MTU

Within 1500 MTU

failover of MTU 1500

local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 66114.bin

don't allow no asdm history

ARP timeout 14400

NAT (inside, outside) source Dynamics one interface

NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

the ssh LOCAL console AAA authentication

Enable http server

http 0.0.0.0 0.0.0.0 outdoors

http 0.0.0.0 0.0.0.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint ASDM_TrustPoint0

Terminal registration

name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

Configure CRL

Crypto ikev1 allow outside

IKEv1 crypto policy 10

authentication crack

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 20

authentication rsa - sig

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 30

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 40

authentication crack

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 50

authentication rsa - sig

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 60

preshared authentication

aes-192 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 70

authentication crack

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 80

authentication rsa - sig

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 90

preshared authentication

aes encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 100

authentication crack

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 110

authentication rsa - sig

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 120

preshared authentication

3des encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 130

authentication crack

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 140

authentication rsa - sig

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 150

preshared authentication

the Encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 65535

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet 192.9.200.0 255.255.255.0 inside

Telnet timeout 30

SSH 0.0.0.0 0.0.0.0 management

SSH 0.0.0.0 0.0.0.0 outdoors

SSH 66.35.45.128 255.255.255.192 outside

SSH 0.0.0.0 0.0.0.0 inside

SSH timeout 30

SSH version 2

Console timeout 0

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

allow outside

AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

AnyConnect enable

tunnel-group-list activate

attributes of Group Policy DfltGrpPolicy

internal RAVPN group policy

RAVPN group policy attributes

value of server WINS 192.9.200.164

value of 66.35.46.84 DNS server 66.35.47.12

VPN-filter value test123

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value test123

Dr.kligerweiss.NET value by default-field

username test encrypted password xxxxxxx

username admin password encrypted aaaaaaaaaaaa privilege 15

vpntest Delahaye of encrypted password username

type tunnel-group RAVPN remote access

attributes global-tunnel-group RAVPN

address RAVPN pool

Group Policy - by default-RAVPN

IPSec-attributes tunnel-group RAVPN

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

Review the ip options

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

!

global service-policy global_policy

context of prompt hostname

no remote anonymous reporting call

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory 2

Subscribe to alert-group configuration periodic monthly 2

daily periodic subscribe to alert-group telemetry

aes encryption password

Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

: end

COL-ASA-01 #.

Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

COL-ASA-01 #.

Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

Hello

The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

You can try the following changes

attributes global-tunnel-group RAVPN

No address RAVPN pool

no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

attributes global-tunnel-group RAVPN

address RAVPN pool

no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

the object of the LAN network

192.168.200.0 subnet 255.255.255.0

network of the VPN-POOL object

192.168.201.0 subnet 255.255.255.0

NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

No source (indoor, outdoor) nat Dynamics one interface

NAT source auto after (indoor, outdoor) dynamic one interface

NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

Hope this helps

Let me know if it works for you

-Jouni

Problem with ASA 5505 VPN remote access

After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?

Here is the cfg running of the ASA

----------------------------------------------------------------------------------------

: Saved

:

ASA Version 8.4 (1)

!

hostname NCHCO

enable encrypted password xxxxxxxxxxxxxxx

xxxxxxxxxxx encrypted passwd

names of

description of NCHCO name 192.168.2.0 City offices

name 192.168.2.80 VPN_End

name 192.168.2.70 VPN_Start

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.2.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address **. ***. 255.255.255.248

!

interface Ethernet0/0

switchport access vlan 2

Speed 100

full duplex

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

boot system Disk0: / asa841 - k8.bin

passive FTP mode

network of the NCHCO object

Subnet 192.168.2.0 255.255.255.0

network object obj - 192.168.1.0

subnet 192.168.1.0 255.255.255.0

network object obj - 192.168.2.64

subnet 192.168.2.64 255.255.255.224

network object obj - 0.0.0.0

subnet 0.0.0.0 255.255.255.0

network obj_any object

subnet 0.0.0.0 0.0.0.0

the Web server object network

the FINX object network

Home 192.168.2.11

rdp service object

source between 1-65535 destination eq 3389 tcp service

Rdp description

outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0

inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224

permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224

outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

LAN_Access list standard access allowed 192.168.2.0 255.255.255.0

LAN_Access list standard access allowed 0.0.0.0 255.255.255.0

NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0

AnyConnect_Client_Local_Print deny ip extended access list a whole

AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

print the access-list AnyConnect_Client_Local_Print Note Windows port

AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

outside_access_in list extended access permit tcp any object FINX eq 3389

outside_access_in_1 list extended access allowed object rdp any object FINX

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 649.bin

don't allow no asdm history

ARP timeout 14400

NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0

NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64

NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64

!

network obj_any object

NAT dynamic interface (indoor, outdoor)

the FINX object network

NAT (inside, outside) interface static service tcp 3389 3389

Access-group outside_access_in_1 in interface outside

Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

network-acl outside_nat0_outbound

WebVPN

SVC request to enable default svc

Enable http server

http 192.168.1.0 255.255.255.0 inside

http *. **. ***. 255.255.255.255 outside

http *. **. ***. 255.255.255.255 outside

http NCHCO 255.255.255.0 inside

http 96.11.251.186 255.255.255.255 outside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform

IKEv1 crypto ipsec transform-set l2tp-transformation mode transit

Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1

transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1

Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1

transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1

Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

crypto dynamic-map dyn-map 10 set pfs Group1

crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1

dynamic-map encryption dyn-map 10 value reverse-road

Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1

Crypto-map dynamic outside_dyn_map 20 the value reverse-road

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs Group1

peer set card crypto outside_map 1 74.219.208.50

card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1

map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

inside crypto map inside_map interface

card crypto vpn-map 1 match address outside_1_cryptomap_1

card crypto vpn-card 1 set pfs Group1

set vpn-card crypto map peer 1 74.219.208.50

card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map

dynamic vpn-map 10 dyn-map ipsec isakmp crypto map

crypto isakmp identity address

Crypto ikev1 allow inside

Crypto ikev1 allow outside

IKEv1 crypto ipsec-over-tcp port 10000

IKEv1 crypto policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

IKEv1 crypto policy 15

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

IKEv1 crypto policy 35

preshared authentication

3des encryption

sha hash

Group 2

life 86400

enable client-implementation to date

Telnet 192.168.1.0 255.255.255.0 inside

Telnet NCHCO 255.255.255.0 inside

Telnet timeout 5

SSH 192.168.1.0 255.255.255.0 inside

SSH NCHCO 255.255.255.0 inside

SSH timeout 5

Console timeout 0

dhcpd address 192.168.2.150 - 192.168.2.225 inside

dhcpd dns 216.68.4.10 216.68.5.10 interface inside

lease interface 64000 dhcpd inside

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

value of server DNS 192.168.2.1

L2TP ipsec VPN-tunnel-Protocol ikev1

nchco.local value by default-field

attributes of Group Policy DfltGrpPolicy

value of server DNS 192.168.2.1

L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client

allow password-storage

enable IPSec-udp

enable dhcp Intercept 255.255.255.0

the address value VPN_Pool pools

internal NCHCO group policy

NCHCO group policy attributes

value of 192.168.2.1 DNS Server 8.8.8.8

Ikev1 VPN-tunnel-Protocol

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1

value by default-field NCHCO.local

admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username

username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg

username NCHvpn99 password dhn. JzttvRmMbHsP encrypted

attributes global-tunnel-group DefaultRAGroup

address (inside) VPN_Pool pool

address pool VPN_Pool

authentication-server-group (inside) LOCAL

authentication-server-group (outside LOCAL)

LOCAL authority-server-group

authorization-server-group (inside) LOCAL

authorization-server-group (outside LOCAL)

Group Policy - by default-DefaultRAGroup

band-Kingdom

band-band

IPSec-attributes tunnel-group DefaultRAGroup

IKEv1 pre-shared-key *.

NOCHECK Peer-id-validate

tunnel-group DefaultRAGroup ppp-attributes

No chap authentication

no authentication ms-chap-v1

ms-chap-v2 authentication

tunnel-group DefaultWEBVPNGroup ppp-attributes

PAP Authentication

ms-chap-v2 authentication

tunnel-group 74.219.208.50 type ipsec-l2l

IPSec-attributes tunnel-group 74.219.208.50

IKEv1 pre-shared-key *.

type tunnel-group NCHCO remote access

attributes global-tunnel-group NCHCO

address pool VPN_Pool

Group Policy - by default-NCHCO

IPSec-attributes tunnel-group NCHCO

IKEv1 pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

call-home

Profile of CiscoTAC-1

no active account

http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

email address of destination [email protected] / * /

destination-mode http transport

Subscribe to alert-group diagnosis

Subscribe to alert-group environment

Subscribe to alert-group monthly periodic inventory

monthly periodicals to subscribe to alert-group configuration

daily periodic subscribe to alert-group telemetry

Cryptochecksum:a2110206e1af06974c858fb40c6de2fc

: end

ASDM image disk0: / asdm - 649.bin

ASDM VPN_Start 255.255.255.255 inside location

ASDM VPN_End 255.255.255.255 inside location

don't allow no asdm history

---------------------------------------------------------------------------------------------------------------

And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:

---------------------------------------------------------------------------------------------------------------

Cisco Systems VPN Client Version 5.0.07.0440

Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 6.1.7601 Service Pack 1

Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\

1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026

Try to find a certificate using hash Serial.

2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027

Found a certificate using hash Serial.

3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011

RELOADED successfully certificates in all certificate stores.

4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002

Start the login process

5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "*." **. ***. *** »

7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B

Try to establish a connection with *. **. ***. ***.

8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001

From IKE Phase 1 negotiation

9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***

10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001

Peer is a compatible peer Cisco-Unity

13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

Peer supports XAUTH

14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

Peer supports the DPD

15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

Peer supports NAT - T

16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

Peer supports fragmentation IKE payloads

17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001

IOS Vendor ID successful construction

18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***

19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083

IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4

20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072

Automatic NAT detection status:

Remote endpoint is NOT behind a NAT device

This effect is NOT behind a NAT device

21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015

Launch application xAuth

25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012

Attributes of the authentication request is 6: 00.

26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017

xAuth application returned

27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008

IPSec driver started successfully

29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E

Customer address a request from firewall to hub

35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70

39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0

40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1

41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8

42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001

43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001

44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F

SPLIT_NET #1

= 192.168.2.0 subnet

mask = 255.255.255.0

Protocol = 0

SRC port = 0

port dest = 0

45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local

46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710

47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11

49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019

Data in mode Config received

51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056

Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0

52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***

53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify has value of 86400 seconds

56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047

This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now

57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">

59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify is set to 28800 seconds

60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***

61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059

IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)

62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025

OUTGOING ESP SPI support: 0xAAAF4C1C

63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026

Charges INBOUND ESP SPI: 0x3EBEBFC5

64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

Destination mask subnet Gateway Interface metric

0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001

Launch VAInst64 for controlling IPSec virtual card

66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034

The virtual card has been activated:

IP=192.168.2.70/255.255.255.0

DNS = 192.168.2.1, 8.8.8.8

WINS = 0.0.0.0 0.0.0.0

Domain = NCHCO.local

Split = DNS names

67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

Destination mask subnet Gateway Interface metric

0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261

255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261

68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038

Were saved successfully road to file changes.

69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

Destination mask subnet Gateway Interface metric

0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100

96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261

192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100

192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261

192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261

224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261

255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261

70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036

The routing table has been updated for the virtual card

71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A

A secure connection established

72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

Look at address added to 96.11.251.149. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

Look at address added to 192.168.2.70. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001

Did not find the smart card to watch for removal

75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

Creates a new key structure

77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

Adding key with SPI = 0x1c4cafaa in the list of keys

78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

Creates a new key structure

79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

Adding key with SPI = 0xc5bfbe3e in the list of keys

80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F

Assigned WILL interface private addr 192.168.2.70

81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037

Configure the public interface: 96.11.251.149. SG: **.**.***.***

82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046

Define indicator tunnel set up in the registry to 1.

83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D

Upon request of the DPD to *. **. ***. , our seq # = 107205276

85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040

Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276

88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019

Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e

89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D

Upon request of the DPD to *. **. ***. , our seq # = 107205277

91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040

Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277

94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D

Upon request of the DPD to *. **. ***. , our seq # = 107205278

96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040

Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278

---------------------------------------------------------------------------------------------------------------

Any help would be appreciated, thanks!

try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.

Allow remote access to the VPN Cisco ASDM

Hello

I am trying to access asdm Setup for the user remote vpn. Our ASA running version 9.1 (1). ASDM is running version 7.1 (1) 52

I have apart from the interface within the interface enabled for vpn tunnel and I use 3rd interface (asdm_inf) dedicated to this purpose.

In the asdm, I enabled the management to asdm_inf interface. In the section ASDM, HTTPS, Telnet, SSH, I also add ASDM/HTTPS(port 444) for asdm_inf, ip_address 0.0.0.0 mask 0.0.0.0.

However, when I connect to the vpn client and try https://asdm_inf:444, the connection is broken with timeout.

Where could I go wrong? Any help would be appreciated.

Thank you

Hello

Well, split tunnel is incorrect, you are tunneling to 172.16.66.0/24, while your BFD which you want to manage the ASDM to is 192.168.244.0/24, so the ACL split tunnel should also 192.168.244.0/24 network.

ASA 5505 - remote access VPN to access various internal networks

Hi all

A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.

Here is the config:

:

ASA Version 8.2 (5)

!

ciscoasa hostname

enable encrypted password xxx

XXX encrypted passwd

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 200.190.1.15 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address 255.255.255.0 xxxxxxx

!

exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

passive FTP mode

access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any

outside_access_in list extended access permit icmp any external interface

access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0

Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0

MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool

IP verify reverse path to the outside interface

ICMP unreachable rate-limit 1 burst-size 1

ICMP allow any inside

ICMP allow all outside

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 200.190.1.0 255.255.255.0

inside_access_in access to the interface inside group

Access-group outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1

Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1

Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1

Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

http server enable 10443

http server idle-timeout 5

Server of http session-timeout 30

HTTP 200.190.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

Crypto ca certificate chain _SmartCallHome_ServerCA

certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

(omitted)

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Crypto isakmp nat-traversal 3600

Telnet timeout 5

SSH 200.190.1.0 255.255.255.0 inside

SSH timeout 5

SSH version 2

Console timeout 5

dhcpd outside auto_config

!

a basic threat threat detection

scanning-threat shun threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

allow outside

internal MD_SSL_Gp_Pol group strategy

attributes of Group Policy MD_SSL_Gp_Pol

VPN-tunnel-Protocol webvpn

WebVPN

list of URLS no

disable the port forward

hidden actions no

disable file entry

exploration of the disable files

disable the input URL

internal MD_IPSEC_Tun_Gp group strategy

attributes of Group Policy MD_IPSEC_Tun_Gp

value of banner welcome to remote VPN

VPN - connections 1

VPN-idle-timeout 5

Protocol-tunnel-VPN IPSec webvpn

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl

the address value Remote_IPSEC_VPN_Pool pools

WebVPN

value of the RDP URL-list

attributes of username (omitted)

VPN-group-policy MD_IPSEC_Tun_Gp

type of remote access service

type tunnel-group MD_SSL_Profile remote access

attributes global-tunnel-group MD_SSL_Profile

Group Policy - by default-MD_SSL_Gp_Pol

type tunnel-group MD_IPSEC_Tun_Gp remote access

attributes global-tunnel-group MD_IPSEC_Tun_Gp

address pool Remote_IPSEC_VPN_Pool

Group Policy - by default-MD_IPSEC_Tun_Gp

IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp

pre-shared key *.

!

!

context of prompt hostname

: end

The following ACL and NAT exemption ACL split tunnel is incorrect:

MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

It should have been:

Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0

access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

Then 'clear xlate' and reconnect with the VPN Client.

Hope that helps.

Problem with remote access VPN on ASA 5505

I currently have a problem of an ASA 5505 configuration to connect via VPN remote access by using the Cisco VPN Client 5.0.07.0440 under Windows 8 Pro x 64. The VPN client will prompt you for the user name and password during the connection process, but fails soon after.

The VPN client connects is as follows:

---------------------------------------------------------------------------------------------------------------------------------------

Cisco Systems VPN Client Version 5.0.07.0440

Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 6.2.9200

2 15:09:21.240 11/12/12 Sev = Info/4 CM / 0 x 63100002

Start the login process

3 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

4 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "*." **. ***. *** »

5 15:09:21.287 11/12/12 Sev = Info/6 IKE/0x6300003B

Try to establish a connection with *. **. ***. ***.

6 15:09:21.287 11/12/12 Sev = Info/4 IKE / 0 x 63000001

From IKE Phase 1 negotiation

7 15:09:21.303 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***

8 15:09:21.365 11/12/12 Sev = Info/6 GUI/0x63B00012

Attributes of the authentication request is 6: 00.

9 15:09:21.334 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

10 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

11 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer is a compatible peer Cisco-Unity

12 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports XAUTH

13 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports the DPD

14 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports NAT - T

15 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports fragmentation IKE payloads

16 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000001

IOS Vendor ID successful construction

17 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***

18 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000055

Sent a keepalive on the IPSec Security Association

19 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000083

IKE port in use - Local Port = 0xFBCE, Remote Port = 0 x 1194

20 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000072

Automatic NAT detection status:

Remote endpoint is NOT behind a NAT device

This effect is behind a NAT device

21 15:09:21.334 11/12/12 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

22 15:09:21.365 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

23 15:09:21.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

24 15:09:21.365 11/12/12 Sev = Info/4 CM / 0 x 63100015

Launch application xAuth

25 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700008

IPSec driver started successfully

26 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

27 15:09:27.319 11/12/12 Sev = Info/4 CM / 0 x 63100017

xAuth application returned

28 15:09:27.319 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

29 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

30 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

31 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

32 15:09:27.365 11/12/12 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

33 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300005E

Customer address a request from firewall to hub

34 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

35 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

36 15:09:27.397 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

37 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70

38 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0

39 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1

40 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8

41 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001

42 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO

43 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

44 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (5) built by manufacturers on Saturday, May 20, 11 16:00

45 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

46 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194

47 15:09:27.397 11/12/12 Sev = Info/4 CM / 0 x 63100019

Data in mode Config received

48 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000056

Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0

49 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***

50 15:09:27.444 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

51 15:09:27.444 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

52 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify has value of 86400 seconds

53 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000047

This SA was already alive for 6 seconds, setting expiration 86394 seconds now

54 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

55 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

56 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO *(HASH, DEL) to *. **. ***. ***

57 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000049

IPsec security association negotiation made scrapped, MsgID = CE99A8A8

58 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED

59 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

60 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000058

Received an ISAKMP for a SA message no assets, I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924

61 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">

62 15:09:27.490 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

63 15:09:30.475 11/12/12 Sev = Info/4 IKE/0x6300004B

IKE negotiation to throw HIS (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED

64 15:09:30.475 11/12/12 Sev = Info/4 CM / 0 x 63100012

ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system

65 15:09:30.475 11/12/12 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

66 15:09:30.475 11/12/12 Sev = Info/6 CM / 0 x 63100046

Set indicator established tunnel to register to 0.

67 15:09:30.475 11/12/12 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

68 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

69 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

70 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

71 15:09:30.475 11/12/12 Sev = Info/4 IPSEC/0x6370000A

IPSec driver successfully stopped

---------------------------------------------------------------------------------------------------------------------------------------

The running configuration is the following (there is a VPN site-to-site set up as well at an another ASA 5505, but that works perfectly):

: Saved

:

ASA Version 8.2 (5)

!

hostname NCHCO

Select hTjwXz/V8EuTw9p9 of encrypted password

hTjwXz/V8EuTw9p9 of encrypted passwd

names of

description of NCHCO name 192.168.2.0 City offices

name 192.168.2.80 VPN_End

name 192.168.2.70 VPN_Start

!

interface Ethernet0/0

switchport access vlan 2

Speed 100

full duplex

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.2.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address **. ***. 255.255.255.248

!

boot system Disk0: / asa825 - k8.bin

passive FTP mode

access extensive list ip NCHCO 255.255.255.0 outside_nat0_outbound allow 192.168.1.0 255.255.255.0

access extensive list ip NCHCO 255.255.255.0 inside_nat0_outbound allow 192.168.1.0 255.255.255.0

inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224

access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap allow 192.168.1.0 255.255.255.0

access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap_1 allow 192.168.1.0 255.255.255.0

Standard access list LAN_Access allow NCHCO 255.255.255.0

LAN_Access list standard access allowed 0.0.0.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 645.bin

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

NAT (outside) 0-list of access outside_nat0_outbound

Route outside 0.0.0.0 0.0.0.0 74.219.208.49 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

network-acl outside_nat0_outbound

WebVPN

SVC request to enable default svc

Enable http server

http 192.168.1.0 255.255.255.0 inside

http *. **. ***. 255.255.255.255 outside

http 74.218.158.238 255.255.255.255 outside

http NCHCO 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac l2tp-transform

Crypto ipsec transform-set l2tp-transformation mode transit

Crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

crypto dynamic-map dyn-map 10 set pfs Group1

crypto dynamic-map dyn-map transform 10-set, vpn l2tp-transformation-transformation

dynamic-map encryption dyn-map 10 value reverse-road

Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs Group1

peer set card crypto outside_map 1 74.219.208.50

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

inside crypto map inside_map interface

card crypto vpn-map 1 match address outside_1_cryptomap_1

card crypto vpn-card 1 set pfs Group1

set vpn-card crypto map peer 1 74.219.208.50

card crypto vpn-card 1 set of transformation-ESP-3DES-SHA

dynamic vpn-map 10 dyn-map ipsec isakmp crypto map

crypto isakmp identity address

crypto ISAKMP allow inside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 15

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

crypto ISAKMP policy 35

preshared authentication

3des encryption

sha hash

Group 2

life 86400

crypto ISAKMP ipsec-over-tcp port 10000

enable client-implementation to date

Telnet 192.168.1.0 255.255.255.0 inside

Telnet NCHCO 255.255.255.0 inside

Telnet timeout 5

SSH 192.168.1.0 255.255.255.0 inside

SSH NCHCO 255.255.255.0 inside

SSH timeout 5

Console timeout 0

dhcpd address 192.168.2.150 - 192.168.2.225 inside

dhcpd dns 216.68.4.10 216.68.5.10 interface inside

lease interface 64000 dhcpd inside

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

value of server DNS 192.168.2.1

Protocol-tunnel-VPN IPSec l2tp ipsec

nchco.local value by default-field

attributes of Group Policy DfltGrpPolicy

value of server DNS 192.168.2.1

Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

allow password-storage

enable IPSec-udp

enable dhcp Intercept 255.255.255.0

the address value VPN_Pool pools

internal NCHVPN group policy

NCHVPN group policy attributes

value of 192.168.2.1 DNS Server 8.8.8.8

Protocol-tunnel-VPN IPSec l2tp ipsec

value by default-field NCHCO

admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username

username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg

username, encrypted NCHvpn99 QhZZtJfwbnowceB7 password

attributes global-tunnel-group DefaultRAGroup

address (inside) VPN_Pool pool

address pool VPN_Pool

authentication-server-group (inside) LOCAL

authentication-server-group (outside LOCAL)

LOCAL authority-server-group

authorization-server-group (inside) LOCAL

authorization-server-group (outside LOCAL)

Group Policy - by default-DefaultRAGroup

band-Kingdom

band-band

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared key *.

NOCHECK Peer-id-validate

tunnel-group DefaultRAGroup ppp-attributes

No chap authentication

no authentication ms-chap-v1

ms-chap-v2 authentication

tunnel-group DefaultWEBVPNGroup ppp-attributes

PAP Authentication

ms-chap-v2 authentication

tunnel-group 74.219.208.50 type ipsec-l2l

IPSec-attributes tunnel-group 74.219.208.50

pre-shared key *.

type tunnel-group NCHVPN remote access

attributes global-tunnel-group NCHVPN

address pool VPN_Pool

Group Policy - by default-NCHVPN

IPSec-attributes tunnel-group NCHVPN

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

no remote anonymous reporting call

Cryptochecksum:15852745977ff159ba808c4a4feb61fa

: end

ASDM image disk0: / asdm - 645.bin

ASDM VPN_Start 255.255.255.255 inside location

ASDM VPN_End 255.255.255.255 inside location

don't allow no asdm history

Anyone have any idea why this is happening?

Thank you!

Add, crypto dynamic-map outside_dyn_map 20 value reverse-road.

With respect,

Safwan

VPN remote access - no network connectivity internal!

Hi Experts,

I understand that it is a very common problem when considering the implementations of IPSec VPN for remote access using Cisco VPN Client. But for the last six months, I have tried to configure remote VPN access to as many sites customer and gets stuck to the top with the same question!

-The remote VPN Client connects, authenticates successfully to the local user database (to make things easier, I used the local user authentication), the tunnel is set up (I could see the exit of the isakmp #show her as a AM_ACTIVE ). So I think that the parameters of encryption and authentication for Phase 1 /Phase 2 should work because the tunnel is having successfully established

-Now comes the question, no connectivity to the internal network. I tried all the possible solutions, that I could find online.

1. the most common problem is NAT - Traversal not active

-Compatible NAT - T with the time default keepalive of 20

2. None of the configurations NAT to exempt remote VPN traffic

-A ensured that Nat configurations not present in configuration and internal network 192.168.1.X VPN traffic networks VPN 192.168.5.X /192.168.10.X being exempted NAT

3-Split tunnel configurations

-Reconfigured Split tunnel access list configuration Standard access list expanded (although not required as a Standard access list is more than enouugh, if I'm not mistaken) to allow traffic selected from 192.168.1.X for 192.168.5.X/192.168.10.X that will create routes on Client that allows users to simultaneously access VPN resources and access Internet VPN client. The Tunnel from Split network group was added again to the group policy.

4 enabled Perfect Forward Secrecy (PFS) /Disabled

. It may be an extra charge, it has been disabled / enabled

5. the road opposite Injection

-Ensured that a temporary reverse route has been injected to the routing table by allowing the reverse Route Injection to insert automatically the temporary static routes to the remote tunnel using the command set reverse road networks

A few more interesting things were noted:

Encrypted and Bypassed packages found when a continuous ping started the ASA inside the interface.

No decryption happens of the VPN Client, which means that there is no answer back from the network traffic statistics.

Decryption and packages are found be increasing when I try to ping of the IP address to the customer (192.168.0.10) has published the SAA. But on the SAA, I'm not back any response and showing as? . So that would mean that there is communication of ASA to the customer via the VPN tunnel while no communication is happening from the internal network to the customer

The entire configuration is shown below

ASA Version 8.2 (1)
!
ciscoasa hostname
activate the encrypted password of AS3P3A8i0l6.JxwD
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address IP X.X.X.X 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
access-list extended SHEEP allowed ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
ST1 list extended access permitted ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
IP local pool testpool 192.168.0.10 - 192.168.0.15
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
Crypto-map dynamic dyn1 1jeu reverse-road
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap outside crypto map interface
crypto ca server
SMTP address [email protected] / * /
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.1.10 - 192.168.1.132 inside
dhcpd dns 8.8.8.8 4.4.4.4 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RAVPN group policy
RAVPN group policy attributes
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value ST1
the address value testpool pools
dk Z6zukyDvwVjP7o24 encrypted privilege 15 password username
sv i1gRUVsEALixX3ei encrypted password username
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
address testpool pool
Group Policy - by default-RAVPN
testgroup group tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:48f0863a70b8f382c7b71db0b88620fe
: end

----

Could you please help me identify where I'm going wrong. Its been a long time I have trying to figure out but nothing seems to work! ;-(

Help, please!

Thank you

ANUP

(1) pls replace the tunnel ACL ACL standard split as follows:

no extended ST1 192.168.1.0 ip access list allow 255.255.255.0 192.168.0.0 255.255.255.0

access-list allowed ST1 192.168.1.0 255.255.255.0

(2) add icmp inspection:

Policy-map global_policy

class inspection_default

inspect the icmp

(3) Finally, I add the following so that you can test the ASA inside the interface:

management-access inside

authentication of remote access, vpn and ldap

I have a test environment with 2 hours fireval 5505: the first firewall is remote access VPN server and the Interior of this firewall is a network of domain with a domain controller, DNS server and a workstation. DHCP is disabled and the PC have a static address.outside of the VPN server is attached outside the other ASA 5505 firewall. on the inside of the firewall, there is a workstation.the workstation would be to connect via vpn for remote access on the domain network. I have configured the VPN server for remote access through a wizard and his

configuration is the following

Result of the command: "show running-config"

: Saved

ASA Version 8.2(1)

hostname ciscoasa

domain-name dri.local

enable password 8Ry2YjIyt7RRXU24 encrypted

passwd 2KFQnbNIdI.2KYOU encrypted

names

interface Vlan1

nameif inside

security-level 100

ip address 10.13.74.5 255.255.255.0

interface Vlan2

nameif outside

security-level 0

ip address 192.168.30.1 255.255.255.0

interface Ethernet0/0

switchport access vlan 2

interface Ethernet0/1

interface Ethernet0/2

interface Ethernet0/3

interface Ethernet0/4

interface Ethernet0/5

interface Ethernet0/6

interface Ethernet0/7

ftp mode passive

dns server-group DefaultDNS

domain-name dri.local

access-list inside_nat0_outbound extended permit ip any 192.168.50.0 255.255.255.240

access-list outside_access_in extended permit tcp 192.168.50.0 255.255.255.240 10.13.74.0 255.255.255.0

pager lines 24

logging asdm informational

mtu inside 1500

mtu outside 1500

ip local pool vpnpool 192.168.50.1-192.168.50.10 mask 255.255.255.0

icmp unreachable rate-limit 1 burst-size 1

no asdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 0 access-list inside_nat0_outbound

nat (inside) 1 0.0.0.0 0.0.0.0

access-group outside_access_in in interface outside

route outside 0.0.0.0 0.0.0.0 192.168.30.2 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-record DfltAccessPolicy

action terminate

dynamic-access-policy-record vpnldap

network-acl inside_nat0_outbound

aaa-server vpn protocol ldap

aaa-server vpn (inside) host 10.13.74.20

ldap-base-dn DC=DRI,DC=LOCAL

ldap-group-base-dn cn=test,cn=users,dc=dri,dc=local

ldap-scope subtree

ldap-naming-attribute sAMAccountName

ldap-login-password *

ldap-login-dn cn=test,cn=users,dc=dri,dc=local

server-type microsoft

http server enable

http 10.13.74.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac

crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac

crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac

crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac

crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac

crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac

crypto ipsec security-association lifetime seconds 28800

crypto ipsec security-association lifetime kilobytes 4608000

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5

crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP

crypto map outside_map interface outside

crypto isakmp enable outside

crypto isakmp policy 10

authentication pre-share

encryption 3des

hash sha

group 2

lifetime 86400

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd auto_config outside

dhcpd address 10.13.74.9-10.13.74.40 inside

threat-detection basic-threat

threat-detection statistics access-list

no threat-detection statistics tcp-intercept

webvpn

group-policy drivpn internal

group-policy drivpn attributes

dns-server value 10.13.74.20 10.8.2.5

vpn-tunnel-protocol IPSec l2tp-ipsec

default-domain value dri.local

tunnel-group drivpn type remote-access

tunnel-group drivpn general-attributes

address-pool vpnpool

authentication-server-group vpn

default-group-policy drivpn

tunnel-group drivpn ipsec-attributes

pre-shared-key *

class-map inspection_default

match default-inspection-traffic

policy-map type inspect dns preset_dns_map

parameters

message-length maximum 512

policy-map global_policy

class inspection_default

inspect dns preset_dns_map

inspect ftp

inspect h323 h225

inspect h323 ras

inspect rsh

inspect rtsp

inspect esmtp

inspect sqlnet

inspect skinny

inspect sunrpc

inspect xdmcp

inspect sip

inspect netbios

inspect tftp

service-policy global_policy global

prompt hostname context

Cryptochecksum:1fc23fb20a74f208b3cde5711633ad3d

: end

When I tried to workstation on the internal part of the second firewall (no remote access vpn server) to connect to the vpn, everything is ok. I used the cisco vpn client, but I can't ping domain controller, workstation, I can't use the shared folder on them. Why?

Please help me

Thank you

Thanks for letting me know! Can you please give the station "answered"? Thank you!

Telnet/ssh/http remote access LWAP CLI

Similar Questions

Maybe you are looking for