Test of the RADIUS server options

Hello

Does anyone have experience in the radius server availability tests? I have what the switch is used to test the availability of the radius server and what measures he will take after the detection of server are dead? Setup is done with ISE 1.4.

Hello

Because how switch contact RADIUS and how to configure the switch for dead timers, I will redirect you on the Cisco documentation which is very simple and complete as well.

http://www.Cisco.com/c/en/us/products/collateral/iOS-NX-OS-software/iDEN...

All parameters to mark a server as dead and how long it will be considered as dead are tweak-able. Setting dynamically some servers as dead if no responses may result in better performance of RADIUS response.

Thank you

PS: Please don't forget to rate and score as correct answer if this answered your question.

Tags: Cisco Security

Similar Questions

Cisco Catalyst 2960-S switch configured for 802. 1 x sends a query to access the Radius Server Radius

Setup

Cisco Catalyst 2960-S running 15.0.2 - SE8

Under Centos freeRadius 6.4 RADIUS server

Client (supplicant) running Windows 7

When Windows client is connected to the port (port 12 in my setup) with authentication of 802. 1 x active switch, show of Wireshark that catalyst sends ask EAP and the client responds with EAP response. But it made not the request to the Radius server. The RADIUS test utility 'aaa RADIUS testuser password new-code test group' works.
Here is my config running. Any advice would be greatly appreciated.
#show running mySwitch-
mySwitch #show running-config
Building configuration...

Current configuration: 2094 bytes
!
version 12.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname myswitch
!
boot-start-marker
boot-end-marker
!
activate the password secret 5 $1$ Z1z6$ kqvVYRQdVRZ0h8aDTV5DR0 enable password!
!
!
AAA new-model
!
!
AAA dot1x group group radius aaa accounting dot1x default start-stop radius authentication group!
!
!
AAA - the id of the joint session
1 supply ws-c2960s-24ts-l switch
!
!
!
!
!
control-dot1x system-auth
pvst spanning-tree mode
spanning tree extend id-system
!
!
!
!
internal allocation policy of VLAN no ascendant interface FastEthernet0 no stop ip address!
GigabitEthernet1/0/1 interface
!
interface GigabitEthernet1/0/2
!
interface GigabitEthernet1/0/3
!
interface GigabitEthernet1/0/4
!
interface GigabitEthernet1/0/5
!
interface GigabitEthernet1/0/6
!
interface GigabitEthernet1/0/7
!
interface GigabitEthernet1/0/8
!
interface GigabitEthernet1/0/9
!
interface GigabitEthernet1/0/10
!
interface GigabitEthernet1/0/11
!
interface GigabitEthernet1/0/12
switchport mode access
Auto control of the port of authentication
dot1x EAP authenticator
!
interface GigabitEthernet1/0/13
!
interface GigabitEthernet1/0/14
!
interface GigabitEthernet1/0/15
!
interface GigabitEthernet1/0/16
!
interface GigabitEthernet1/0/17
!
interface GigabitEthernet1/0/18
!
interface GigabitEthernet1/0/19
!
interface GigabitEthernet1/0/20
!
interface GigabitEthernet1/0/21
!
interface GigabitEthernet1/0/22
!
interface GigabitEthernet1/0/23
!
interface GigabitEthernet1/0/24
!
interface GigabitEthernet1/0/25
!
interface GigabitEthernet1/0/26
!
interface GigabitEthernet1/0/27
!
interface GigabitEthernet1/0/28
!
interface Vlan1
IP 10.1.2.12 255.255.255.0
!
IP http server
IP http secure server
activate the IP sla response alerts
recording of debug trap
10.1.2.1 host connection tcp port 514 RADIUS-server host 10.1.2.1 transport auth-port 1812 acct-port 1646 timeout 3 retransmit testing123 key 3.
Line con 0
line vty 0 4
password password
line vty 5 15
password password
!
end

interface GigabitEthernet1/0/16
!
interface GigabitEthernet1/0/17
!
interface GigabitEthernet1/0/18
!
interface GigabitEthernet1/0/19
!
interface GigabitEthernet1/0/20

Have you run wireshark on the server because the request to switch? If so you make sure that there is a response from the server? For Windows network POLICY Server (I've never tried Centos), you must ensure that the request is related to a policy which then authenticates, or denies access. Usually, it is a matter of such attributes and the seller.

Regarding the configuration, it seems a bit out of the AAA. Try to remove the:

line "aaa dot1x group service radius authentication" and this by using instead:

"aaa dot1x default radius authentication group". After the dot1x word you are supposed to provide a list of the authentication or the default Word if you do not want to use a list.

Cisco 1812 no contact to the Radius Server

Hi guys,.

IM pretty new to cisco and plays with an 1812 products... I am trying set up an easy VPN server, with the support of ray and I can see that I did everything right, but there is a problem, because the router do not contact the RADIUS server and the RADIUS server has been tested ok.

Anyone who can see what I'm missing? Worked with this problem for 3 days now.

Here is my CONF.

Current configuration: 9170 bytes

!

! Last modification of the configuration to 13:44:49 UTC Tuesday, October 12, 2010

!

version 15.1

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

router host name

!

boot-start-marker

boot-end-marker

!

!

no set record in buffered memory

!

AAA new-model

!

!

AAA server radius sdm-vpn-server-group 1 group

auth-port 1645 90.0.0.245 Server acct-port 1646

!

AAA authentication login default local

AAA authentication login sdm_vpn_xauth_ml_1-passwd-expiry group sdm-vpn-server-group 1

AAA authorization exec default local

AAA authorization sdm_vpn_group_ml_1 LAN

!

!

!

!

!

AAA - the id of the joint session

!

Crypto pki token removal timeout default 0

!

Crypto pki trustpoint TP-self-signed-250973313

enrollment selfsigned

name of the object cn = IOS - Self - signed - certificate - 250973313

revocation checking no

!

!

TP-self-signed-250973313 crypto pki certificate chain

certificate self-signed 01

308201A 5 A0030201 02020101 3082023C 300 D 0609 2A 864886 F70D0101 04050030

2 040355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30

69666963 32353039 37333331 33301E17 313031 30313230 39343333 0D 6174652D

395A170D 2E302C06 1325494F 03540403 32303031 30313030 30303030 5A 303031

532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3235 30393733 642D

06092A 86 4886F70D 01010105 33313330 819F300D 00308189 02818100 0003818D

BCF94FB0 77240E92 B703CE70 556D5D22 A57823E5 DD4CD4C4 12D639DE 5E97DB2D

81FBB304 9FA677A6 CAD84F96 9734081B F8F8FAAE 000B02FB AEF7C7B1 73AFA44B

7D27E112 8991F03B 3D4FD484 34E2EA9F BD426F73 48778F2A AD35AAD6 EC00805D

249B 8702 D545AEEA 40670DFD 3E6BEC29 EE48A0C6 CB7694FD 722D1A62 3A499CC5

02030100 01A 36630 03551 D 13 64300F06 0101FF04 05300301 01FF3011 0603551D

11040A 30 08820652 6F757465 72301F06 23 04183016 801462CB F6BD12F6 03551D

080C8A89 F9FBBDCE 9751528A FFFD301D 0603551D 0E041604 1462CBF6 BD12F608

0C8A89F9 FBBDCE97 51528AFF FD300D06 092 HAS 8648 01040500 03818100 86F70D01

ACA87977 CF 55225 6 9147E57E 8B5A8CA8 46348CAF 801D11C6 9DA57C69 14FA5076

6844F0CC 4CBEB541 136A483A 69F7B7F0 E44474E8 14DC2E80 CC04F840 B 3531, 884

F08A492D 8C3902C0 725EE93D AC83A29F 799AAE0F 5795484B B3D02F84 911DB135

5 189766 C30DA111 6B9B4E46 E999DA5B 202 21B0B9D4 HAS 6900 07A93D8D 41C7FD21

quit smoking

dot11 syslog

IP source-route

!

!

!

!

!

IP cef

No ipv6 cef

!

Authenticated MultiLink bundle-name Panel

!

!

!

license udi pid CISCO1812/K9 sn FCZ10232108

username admin privilege 15 secret 5 P677 $1$ $ Rggfdgt8MeD8letZDL08d.

!

!

!

type of class-card inspect correspondence sdm-nat-smtp-1

game group-access 101

smtp Protocol game

type of class-card inspect entire game SDM_AH

match the name of group-access SDM_AH

type of class-card inspect all sdm-cls-insp-traffic game

match Protocol cuseeme

dns protocol game

ftp protocol game

h323 Protocol game

https protocol game

match icmp Protocol

match the imap Protocol

pop3 Protocol game

netshow Protocol game

Protocol shell game

match Protocol realmedia

match rtsp Protocol

smtp Protocol game

sql-net Protocol game

streamworks Protocol game

tftp Protocol game

vdolive Protocol game

tcp protocol match

udp Protocol game

inspect the class-map match sdm-insp-traffic type

corresponds to the class-map sdm-cls-insp-traffic

type of class-card inspect all SDM-voice-enabled game

h323 Protocol game

Skinny Protocol game

sip protocol game

type of class-card inspect entire game SDM_IP

match the name of group-access SDM_IP

type of class-card inspect entire game SDM_ESP

match the name of group-access SDM_ESP

type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC

match Protocol isakmp

match Protocol ipsec-msft

corresponds to the SDM_AH class-map

corresponds to the SDM_ESP class-map

type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT

corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map

type of class-card inspect all match sdm-cls-icmp-access

match icmp Protocol

tcp protocol match

udp Protocol game

type of class-card inspect correspondence sdm-invalid-src

game group-access 100

type of class-card inspect correspondence sdm-icmp-access

corresponds to the class-map sdm-cls-icmp-access

type of class-card inspect correspondence sdm-Protocol-http

http protocol game

!

!

type of policy-card inspect sdm-permits-icmpreply

class type inspect sdm-icmp-access

inspect

class class by default

Pass

type of policy-card inspect sdm-pol-NATOutsideToInside-1

class type inspect sdm-nat-smtp-1

inspect

class class by default

drop

type of policy-map inspect sdm - inspect

class type inspect sdm-invalid-src

Drop newspaper

class type inspect sdm-insp-traffic

inspect

class type inspect sdm-Protocol-http

inspect

class type inspect SDM-voice-enabled

inspect

class class by default

Pass

type of policy-card inspect sdm-enabled

class type inspect SDM_EASY_VPN_SERVER_PT

Pass

class class by default

drop

type of policy-card inspect sdm-license-ip

class type inspect SDM_IP

Pass

class class by default

Drop newspaper

!

security of the area outside the area

safety zone-to-zone

ezvpn-safe area of zone

safety zone-pair sdm-zp-self-out source destination outside zone auto

type of service-strategy inspect sdm-permits-icmpreply

source of sdm-zp-out-auto security area outside zone destination auto pair

type of service-strategy inspect sdm-enabled

safety zone-pair sdm-zp-in-out source in the area of destination outside the area

type of service-strategy inspect sdm - inspect

sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area

type of service-strategy inspect sdm-pol-NATOutsideToInside-1

in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security

type of service-strategy inspect sdm-license-ip

source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination

type of service-strategy inspect sdm-license-ip

safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area

type of service-strategy inspect sdm-license-ip

safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area

type of service-strategy inspect sdm-license-ip

!

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

!

Configuration group Sindby crypto isakmp client

key TheSommerOf03

90.0.0.240 DNS 8.8.8.8

win 90.0.0.240

SBYNET field

pool SDM_POOL_2

Max-users 15

netmask 255.255.255.0

ISAKMP crypto sdm-ike-profile-1 profile

identity Sindby group match

client authentication list sdm_vpn_xauth_ml_1

ISAKMP authorization list sdm_vpn_group_ml_1

client configuration address respond

virtual-model 1

!

!

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac

Crypto ipsec transform-set esp-SHA2-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA3-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA4-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA5-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA6-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA7-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA8-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA9-ESP-3DES esp-sha-hmac

Crypto ipsec transform-set esp-3des SHA10-ESP-3DES esp-sha-hmac

!

Profile of crypto ipsec SDM_Profile1

game of transformation-ESP-3DES-SHA10

isakmp-profile sdm-ike-profile-1 game

!

!

!

!

!

!

interface BRI0

no ip address

encapsulation hdlc

Shutdown

!

interface FastEthernet0

Description $FW_OUTSIDE$

IP address 93.166.xxx.xxx 255.255.255.248

NAT outside IP

IP virtual-reassembly in

outside the area of security of Member's area

automatic duplex

automatic speed

!

interface FastEthernet1

no ip address

Shutdown

automatic duplex

automatic speed

!

interface FastEthernet2

!

interface FastEthernet3

!

interface FastEthernet4

!

interface FastEthernet5

!

FastEthernet6 interface

!

interface FastEthernet7

!

interface FastEthernet8

!

interface FastEthernet9

!

type of interface virtual-Template1 tunnel

IP unnumbered FastEthernet0

ezvpn-safe area of Member's area

ipv4 ipsec tunnel mode

Tunnel SDM_Profile1 ipsec protection profile

!

interface Vlan1

Description $FW_INSIDE$

IP 90.0.0.190 255.255.255.0

IP nat inside

IP virtual-reassembly in

Security members in the box area

!

local IP SDM_POOL_1 90.0.0.25 pool 90.0.0.29

local IP SDM_POOL_2 90.0.0.75 pool 90.0.0.90

IP forward-Protocol ND

IP http server

local IP http authentication

IP http secure server

IP http timeout policy inactive 600 life 86400 request 10000

!

!

IP nat inside source static tcp 192.168.1.200 25 interface FastEthernet0 25

the IP nat inside source 1 interface FastEthernet0 overload list

IP route 0.0.0.0 0.0.0.0 93.166.xxx.xxx

!

SDM_AH extended IP access list

Remark SDM_ACL = 1 category

allow a whole ahp

SDM_ESP extended IP access list

Remark SDM_ACL = 1 category

allow an esp

SDM_IP extended IP access list

Remark SDM_ACL = 1 category

allow an ip

!

exploitation forest esm config

access-list 1 permit 90.0.0.0 0.0.0.255

Access-list 100 = 128 SDM_ACL category note

access-list 100 permit ip 255.255.255.255 host everything

access-list 100 permit ip 127.0.0.0 0.255.255.255 everything

access-list 100 permit ip 93.166.xxx.xxx 0.0.0.7 everything

Remark SDM_ACL category of access list 101 = 0

IP access-list 101 permit any host 192.168.1.200

!

!

!

!

!

!

RADIUS-server host 90.0.0.245 auth-port 1645 acct-port 1646

!

control plan

!

!

Line con 0

line to 0

line vty 0 4

transport input telnet ssh

!

end

Hello

Looks like you're missing the key from the radius server configuration "RADIUS-server host 90.0.0.245 auth-port 1645 1646 key your_keyacct-port»

Thank you

Wen

How to restrict Internet access by using the RADIUS server via switch Catalyst 3560

Dear all,

I need a configuration using any. I have a small network of 15 users a 3560, which is in turn connected to a router ISR 2811. Interface fastethernet 0/24 switch 3560 I intend to connect to a unix based server RADIUS. ISP is connected on the opposite side of the 2811 to the fa0/0 interface.

I want to make is that if someone among the 15 users tries to access the internet, they must be validated in the RADIUS server by their pre-configured user credentials. (I'm going to store 15 user credentials here). If someone else tries to connect (except those 15) he or she should be denied internet access.

The RADIUS server will be having a login page to type the name of user and password.

Please guide based on what commands I should inject into the 3560 or what specifically, I need to have to run this task.

Thanks in advance!

Samrat.

I only did this in a very long time, but you probably want to do is activate the web authentication.

http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst3560/software/release/12-2_52_se/configuration/guide/3560scg/swwebauth.html

Unable to connect to the radius server

Hello

I do configuration of the radius server on win Server 2008r2 wireless IEEE 802. 1 x.

and I do the configuration on the access point to the RADIUS

in win7 machine when I tried to connect to the server and enter the username and password that I created in AD, but win7 still asked me to username and password and it doesn't show me any error

Please help me

Thank you.

Hello

I suggest you to ask your question at the following link.

http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/

I hope this helps.

Test against the remote server

Y at - it no way to automate or simplify the advancement of confirming a file is good on the testing server to upload to the remote server (production)? AFAICT, it seems that I have to manually upload the files to the production server if I have a defined test server. (I use a dynamic content; I know about the .tmp files, but see more to why this isn't what I want). From what I see, the better I can do is the server of your choice via the drop-down site button and use the synchronization feature.
Maybe the distance/test config is not what I should do, but what for me has been not only have a place to try things, but also use the test server as a production server temporary on these occasions that the production server must be taken offline. (If I have the right SVN, this isn't a viable option either, besides, I have the server backed up using 3 different applications). So, I want my test server files to be a copy of my remote server, including the latest files.
Suggestions?

The test server is usually just to test and you should never really put a test server to a live server. DW can manage several remote servers, but as far as I know, even with CS5.5, you can upload to a remote server at a time. As the servers that you are talking about are in the same data center, it should be possible to configure a second server for redundancy so that if one blocks the other picks up the load. However, I would say that this is not the appropriate forum to get help on configuring redundancy in a datacenter. If your two servers are in 2 data centers different it's a whole other discussion. I would like, there was more that I knew about the subject, but I'm really not familiar with the installation of the network of websites of the scale.

Newbie question on access to the RADIUS server

I've worked before on RADIUS servers running on Windows but not on Unix. I'm new to an environment without any documentation and I make sure I have access to the GANYMEDE/ACS config.

I go to my config switch and I see that ' 10.0.0.1 radius-server.

Then I ssh into ' 10.0.0.1' and I see the below after "method.

From the bottom, you have an idea on how to access the configuration of the ACS in case I need to change any setting it? I tried http://10.0.0.1 but it does not work.

-bash-3, $00 ls
bin features core net sbin TT_DB
Start the etc. opt system usr lib
export of CDROM lost + found tftpboot var platform
dev House Dem proc tmp flight-bash-3. $00 ls
bin features core net sbin TT_DB
Start the etc. opt system usr lib
export of CDROM lost + found tftpboot var platform
dev House Dem proc tmp flight

Try http://10.0.0.1:2002 for ACS listening on port default 2002.

Pete

change the IP address of the RADIUS server

Hi all

I'm looking to reloacte a Ganymede server + inside the demilitarized zone and, consequently, the server will be on a new IP range.

I will seek the role these command using chat tools that I have a large number of switches

the configuration of switches is less than

existing Ganymede:

host key 10.11.11.40 radius-server 9090897979800090908

Now I move the server to a new IP 10.99.1.40

If I put the command

host key 10.99.1.40 radius-server 9090897979800090908

the configuration looks like this:

host key 10.11.11.40 radius-server 9090897979800090908

host key 10.99.1.40 radius-server 9090897979800090908

I need to confirm that when I switch the server again this IP switches will turn to the new ip address of 10.99.1.40 and I do after all, that is, remove the old line: no host key 10.11.11.40 radius-server 9090897979800090908

Or it will work now and I have to set up a group that is located at the bottom of the page from the link below

http://www.Cisco.com/c/en/us/TD/docs/iOS/12_2/security/configuration/guide/fsecur_c/scftplus.html

Thank you very much

The method explained in the linked document is the most recent. On IOS 15.x the previous method (which still works) generates a message in the cli parser that it was withdrawn and Cisco recommends to the new method.

That said, each method should work. The new method should be good all switches or routers with IOS 12.0 +.

When there are two servers configured, IOS them will try in order and, if a response is not received in three trials (each in the case of multiple servers), it may fall to another configured method aaa (or fails aaa if no second method has been defined)

Assign the radius server to specific groups of VPN 3000

Last week, I assigned a test Cisco ACS server to be used for authentication and device of accounting for a specific group on a Cisco VPN concentrator 3060. When I looked at ACS, it appears that not only the Group was to go there but others through this way and using the default values on the Cisco Secure ACS. Is it possible that I can make sure only the traffic assigned to this specific group of VPN using the ACS server defined?

Thank you

Hello

Not sure about your implementation. But you must configure the group for this specific ad group map can only authentication.

In the external group map db, map

Group ACS VPN---> with<---- ad="" vpn="">

Any other combination should point to any access group.

Kind regards

~ JG

Note the useful messages

How 2 Configure ACS 4.2 to delegate authentication to the radius server

Hello

We need run the following scenario:

Cisco VPN client (or any connect, Cisco SSL VPN client)---> Cisco ASA 5520---> Cisco ACS 4.2---> CAT Authentication Server

The CAT authentication server is a Radius server. It can receive Radius authentication requests and respond. It is used for strong authentication TFA WBS similar to RSA OTP tokens.

The question is: how we set up the 4.2 ACS to delegate authentication request to another Radius server.

Thnx

Add the RSA server as an external database, configure the drop user profile or a group to authenticate on the new external database rather than ACS DB Local (or Windows DB).

Easy as pie!

Please rate if this is useful.

How to account for the Radius Server cisco vpn client

Hello

I would like to realize vpn cisco customers

My config is:

AAA authentication login default local radius group
RADIUS AAA authentication login aaa_radius local group
RADIUS group AAA authorization exec default authenticated if
AAA authorization vpn LAN
failure to exec AAA accounting
action-type market / stop
RADIUS group
!
AAA accounting network aaa_radius
action-type market / stop
RADIUS group

RADIUS-server host x.x.x.x auth-port 1812 acct-port 1813 key xxxxx

No package of accounitng is sent to the server radius, only the packages autthetication

RADIUS server is freeradius

Thank you

Pet

Hello!

The sequence of commands you add to your configuration:

1. in the case of former card crypto

crypto-NAME of the customer accounting card card list aaa_radius

2. in the case of isakmp profiles

Profile of crypto isakmp PROFILE NAME

accounting aaa_radius

When the NAME of the map and the PROFILE NAME real names for you profile crypto map or isakmp respectively.

I hope this helps.

Best regards.

How can I add changes to the site after the publication, in passing does not by the cat of the company. (I used the FTP server option section directly)

How can I add changes in a file of Muse after I already pushed to my domain I bought through GoDaddy using the FTP server directly. I'm not BusinessCatalyst and I don't want to. How can I make changes directly from Muse and then direct update to the site? If this isn't an option, how I add administrators browser edition. I have in the browser active editing on the site, but which is insofar as it allows me to get. He actually let me add someone to do or give me a way.

You can change/update the site directly from Muse through the option publish to publish the Business Catalyst select drop-down list and choose the url for the site.

https://helpx.Adobe.com/Muse/using/publishing-websites.html#id_83339

https://helpx.Adobe.com/Muse/how-to/muse-publish-site-business-catalyst.html

About IBE, you can connect to your site and add site admin users.

Go to Site Settings > users Admin > invite.

Thank you

Sanjit

CFFORM - form validation does not AT ALL during the test on the production server

So I did all my tests on my local test of Coldfusion server. All form input boxes are validated correctly, with a dialog box popping up when it has not been completed
When I upload it on the production server, also running ColdFusion 8, it not there no event at all - no dialog boxes, cfform validation etc...
I use the same client computer to test locally as I test it on the web, and yet I get two different results! Any ideas?

THE FIRST THING to check in this case, it is that you can connect properly to the/cfide/scripts/folder via the web site on the production server. This scripts folder is where ColdFusion retains all its javascript, CSS and other client files used in computing, the and other client UI features. If your browser cannot access these files, these features will not work.

Rapid tests is just to put the /cfide/scripts/wddx.js in your browser on the production server and see if you get the right javascript file. If this isn't the case, you must make sure that there is a CFIDE virtual directory configured in your web site and that this directory is readable by users.

Migrating from Test to the new server - OBIEE
Hello

I was "assessment" OBIEE perfect on a test server small for awhile where I did considerable work on the two reports of the writing. development of dashboards, user security configuration and architecture of data needed in the physical layers / business model and presentations in administration of BI.

My question is, what is the best way to transfer the solution in its current form to another server, without having to make extensive rework?

Thanks for any advice,

Robert.
Lowest level: copy of the catalogue of the RPD and web on the other server, set the NQSConfig.ini and instanceconfig.xml and off you go.

That's assuming you don't have change web messages, add custom images or files, change the styles or skins, you're still pointing to the same data sources etc. etc.

You should take a look at one of the brands of earlier descriptions: http://www.rittmanmead.com/2008/04/28/migration-obiee-projects-between-dev-and-prod-environments/

See you soon,.
C.

Sent to the RADIUS server IP address

Install a GANYMEDE server on network to control console and telnet access to routers and switches. Most of our remote routers have multiple paths wan to RADIUS servers and may present a different IP address depending on what path is available or less busy. This causes an authentication failure that denies access to the equipment. Is it possible to configure the router to always send a specific address or a loopback or internal LAN IP address?

You can also go through the link below

http://my.safaribooksonline.com/book/networking/Cisco-IOS/0596527225/tacacsplus/i85779__heada__4_7

~ BR
Jatin kone

* Does the rate of useful messages *.

Test of the RADIUS server options

Similar Questions

Maybe you are looking for