change the IP address of the RADIUS server

Similar Questions

• Cisco Catalyst 2960-S switch configured for 802. 1 x sends a query to access the Radius Server Radius

  Setup

  Cisco Catalyst 2960-S running 15.0.2 - SE8

  Under Centos freeRadius 6.4 RADIUS server

  Client (supplicant) running Windows 7

  When Windows client is connected to the port (port 12 in my setup) with authentication of 802. 1 x active switch, show of Wireshark that catalyst sends ask EAP and the client responds with EAP response. But it made not the request to the Radius server. The RADIUS test utility 'aaa RADIUS testuser password new-code test group' works.
  Here is my config running. Any advice would be greatly appreciated.
  #show running mySwitch-
  mySwitch #show running-config
  Building configuration...

  Current configuration: 2094 bytes
  !
  version 12.2
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname myswitch
  !
  boot-start-marker
  boot-end-marker
  !
  activate the password secret 5 $1$ Z1z6$ kqvVYRQdVRZ0h8aDTV5DR0 enable password!
  !
  !
  AAA new-model
  !
  !
  AAA dot1x group group radius aaa accounting dot1x default start-stop radius authentication group!
  !
  !
  AAA - the id of the joint session
  1 supply ws-c2960s-24ts-l switch
  !
  !
  !
  !
  !
  control-dot1x system-auth
  pvst spanning-tree mode
  spanning tree extend id-system
  !
  !
  !
  !
  internal allocation policy of VLAN no ascendant interface FastEthernet0 no stop ip address!
  GigabitEthernet1/0/1 interface
  !
  interface GigabitEthernet1/0/2
  !
  interface GigabitEthernet1/0/3
  !
  interface GigabitEthernet1/0/4
  !
  interface GigabitEthernet1/0/5
  !
  interface GigabitEthernet1/0/6
  !
  interface GigabitEthernet1/0/7
  !
  interface GigabitEthernet1/0/8
  !
  interface GigabitEthernet1/0/9
  !
  interface GigabitEthernet1/0/10
  !
  interface GigabitEthernet1/0/11
  !
  interface GigabitEthernet1/0/12
  switchport mode access
  Auto control of the port of authentication
  dot1x EAP authenticator
  !
  interface GigabitEthernet1/0/13
  !
  interface GigabitEthernet1/0/14
  !
  interface GigabitEthernet1/0/15
  !
  interface GigabitEthernet1/0/16
  !
  interface GigabitEthernet1/0/17
  !
  interface GigabitEthernet1/0/18
  !
  interface GigabitEthernet1/0/19
  !
  interface GigabitEthernet1/0/20
  !
  interface GigabitEthernet1/0/21
  !
  interface GigabitEthernet1/0/22
  !
  interface GigabitEthernet1/0/23
  !
  interface GigabitEthernet1/0/24
  !
  interface GigabitEthernet1/0/25
  !
  interface GigabitEthernet1/0/26
  !
  interface GigabitEthernet1/0/27
  !
  interface GigabitEthernet1/0/28
  !
  interface Vlan1
  IP 10.1.2.12 255.255.255.0
  !
  IP http server
  IP http secure server
  activate the IP sla response alerts
  recording of debug trap
  10.1.2.1 host connection tcp port 514 RADIUS-server host 10.1.2.1 transport auth-port 1812 acct-port 1646 timeout 3 retransmit testing123 key 3.
  Line con 0
  line vty 0 4
  password password
  line vty 5 15
  password password
  !
  end

  interface GigabitEthernet1/0/16
  !
  interface GigabitEthernet1/0/17
  !
  interface GigabitEthernet1/0/18
  !
  interface GigabitEthernet1/0/19
  !
  interface GigabitEthernet1/0/20

  Have you run wireshark on the server because the request to switch? If so you make sure that there is a response from the server? For Windows network POLICY Server (I've never tried Centos), you must ensure that the request is related to a policy which then authenticates, or denies access. Usually, it is a matter of such attributes and the seller.

  Regarding the configuration, it seems a bit out of the AAA. Try to remove the:

  line "aaa dot1x group service radius authentication" and this by using instead:

  "aaa dot1x default radius authentication group". After the dot1x word you are supposed to provide a list of the authentication or the default Word if you do not want to use a list.

• Cisco 1812 no contact to the Radius Server

  Hi guys,.

  IM pretty new to cisco and plays with an 1812 products... I am trying set up an easy VPN server, with the support of ray and I can see that I did everything right, but there is a problem, because the router do not contact the RADIUS server and the RADIUS server has been tested ok.

  Anyone who can see what I'm missing? Worked with this problem for 3 days now.

  Here is my CONF.

  Current configuration: 9170 bytes

  !

  ! Last modification of the configuration to 13:44:49 UTC Tuesday, October 12, 2010

  !

  version 15.1

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  router host name

  !

  boot-start-marker

  boot-end-marker

  !

  !

  no set record in buffered memory

  !

  AAA new-model

  !

  !

  AAA server radius sdm-vpn-server-group 1 group

  auth-port 1645 90.0.0.245 Server acct-port 1646

  !

  AAA authentication login default local

  AAA authentication login sdm_vpn_xauth_ml_1-passwd-expiry group sdm-vpn-server-group 1

  AAA authorization exec default local

  AAA authorization sdm_vpn_group_ml_1 LAN

  !

  !

  !

  !

  !

  AAA - the id of the joint session

  !

  Crypto pki token removal timeout default 0

  !

  Crypto pki trustpoint TP-self-signed-250973313

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 250973313

  revocation checking no

  !

  !

  TP-self-signed-250973313 crypto pki certificate chain

  certificate self-signed 01

  308201A 5 A0030201 02020101 3082023C 300 D 0609 2A 864886 F70D0101 04050030

  2 040355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30

  69666963 32353039 37333331 33301E17 313031 30313230 39343333 0D 6174652D

  395A170D 2E302C06 1325494F 03540403 32303031 30313030 30303030 5A 303031

  532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3235 30393733 642D

  06092A 86 4886F70D 01010105 33313330 819F300D 00308189 02818100 0003818D

  BCF94FB0 77240E92 B703CE70 556D5D22 A57823E5 DD4CD4C4 12D639DE 5E97DB2D

  81FBB304 9FA677A6 CAD84F96 9734081B F8F8FAAE 000B02FB AEF7C7B1 73AFA44B

  7D27E112 8991F03B 3D4FD484 34E2EA9F BD426F73 48778F2A AD35AAD6 EC00805D

  249B 8702 D545AEEA 40670DFD 3E6BEC29 EE48A0C6 CB7694FD 722D1A62 3A499CC5

  02030100 01A 36630 03551 D 13 64300F06 0101FF04 05300301 01FF3011 0603551D

  11040A 30 08820652 6F757465 72301F06 23 04183016 801462CB F6BD12F6 03551D

  080C8A89 F9FBBDCE 9751528A FFFD301D 0603551D 0E041604 1462CBF6 BD12F608

  0C8A89F9 FBBDCE97 51528AFF FD300D06 092 HAS 8648 01040500 03818100 86F70D01

  ACA87977 CF 55225 6 9147E57E 8B5A8CA8 46348CAF 801D11C6 9DA57C69 14FA5076

  6844F0CC 4CBEB541 136A483A 69F7B7F0 E44474E8 14DC2E80 CC04F840 B 3531, 884

  F08A492D 8C3902C0 725EE93D AC83A29F 799AAE0F 5795484B B3D02F84 911DB135

  5 189766 C30DA111 6B9B4E46 E999DA5B 202 21B0B9D4 HAS 6900 07A93D8D 41C7FD21

  quit smoking

  dot11 syslog

  IP source-route

  !

  !

  !

  !

  !

  IP cef

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  !

  license udi pid CISCO1812/K9 sn FCZ10232108

  username admin privilege 15 secret 5 P677 $1$ $ Rggfdgt8MeD8letZDL08d.

  !

  !

  !

  type of class-card inspect correspondence sdm-nat-smtp-1

  game group-access 101

  smtp Protocol game

  type of class-card inspect entire game SDM_AH

  match the name of group-access SDM_AH

  type of class-card inspect all sdm-cls-insp-traffic game

  match Protocol cuseeme

  dns protocol game

  ftp protocol game

  h323 Protocol game

  https protocol game

  match icmp Protocol

  match the imap Protocol

  pop3 Protocol game

  netshow Protocol game

  Protocol shell game

  match Protocol realmedia

  match rtsp Protocol

  smtp Protocol game

  sql-net Protocol game

  streamworks Protocol game

  tftp Protocol game

  vdolive Protocol game

  tcp protocol match

  udp Protocol game

  inspect the class-map match sdm-insp-traffic type

  corresponds to the class-map sdm-cls-insp-traffic

  type of class-card inspect all SDM-voice-enabled game

  h323 Protocol game

  Skinny Protocol game

  sip protocol game

  type of class-card inspect entire game SDM_IP

  match the name of group-access SDM_IP

  type of class-card inspect entire game SDM_ESP

  match the name of group-access SDM_ESP

  type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC

  match Protocol isakmp

  match Protocol ipsec-msft

  corresponds to the SDM_AH class-map

  corresponds to the SDM_ESP class-map

  type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT

  corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map

  type of class-card inspect all match sdm-cls-icmp-access

  match icmp Protocol

  tcp protocol match

  udp Protocol game

  type of class-card inspect correspondence sdm-invalid-src

  game group-access 100

  type of class-card inspect correspondence sdm-icmp-access

  corresponds to the class-map sdm-cls-icmp-access

  type of class-card inspect correspondence sdm-Protocol-http

  http protocol game

  !

  !

  type of policy-card inspect sdm-permits-icmpreply

  class type inspect sdm-icmp-access

  inspect

  class class by default

  Pass

  type of policy-card inspect sdm-pol-NATOutsideToInside-1

  class type inspect sdm-nat-smtp-1

  inspect

  class class by default

  drop

  type of policy-map inspect sdm - inspect

  class type inspect sdm-invalid-src

  Drop newspaper

  class type inspect sdm-insp-traffic

  inspect

  class type inspect sdm-Protocol-http

  inspect

  class type inspect SDM-voice-enabled

  inspect

  class class by default

  Pass

  type of policy-card inspect sdm-enabled

  class type inspect SDM_EASY_VPN_SERVER_PT

  Pass

  class class by default

  drop

  type of policy-card inspect sdm-license-ip

  class type inspect SDM_IP

  Pass

  class class by default

  Drop newspaper

  !

  security of the area outside the area

  safety zone-to-zone

  ezvpn-safe area of zone

  safety zone-pair sdm-zp-self-out source destination outside zone auto

  type of service-strategy inspect sdm-permits-icmpreply

  source of sdm-zp-out-auto security area outside zone destination auto pair

  type of service-strategy inspect sdm-enabled

  safety zone-pair sdm-zp-in-out source in the area of destination outside the area

  type of service-strategy inspect sdm - inspect

  sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area

  type of service-strategy inspect sdm-pol-NATOutsideToInside-1

  in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security

  type of service-strategy inspect sdm-license-ip

  source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination

  type of service-strategy inspect sdm-license-ip

  safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area

  type of service-strategy inspect sdm-license-ip

  safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area

  type of service-strategy inspect sdm-license-ip

  !

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group Sindby crypto isakmp client

  key TheSommerOf03

  90.0.0.240 DNS 8.8.8.8

  win 90.0.0.240

  SBYNET field

  pool SDM_POOL_2

  Max-users 15

  netmask 255.255.255.0

  ISAKMP crypto sdm-ike-profile-1 profile

  identity Sindby group match

  client authentication list sdm_vpn_xauth_ml_1

  ISAKMP authorization list sdm_vpn_group_ml_1

  client configuration address respond

  virtual-model 1

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac

  Crypto ipsec transform-set esp-SHA2-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA3-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA4-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA5-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA6-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA7-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA8-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA9-ESP-3DES esp-sha-hmac

  Crypto ipsec transform-set esp-3des SHA10-ESP-3DES esp-sha-hmac

  !

  Profile of crypto ipsec SDM_Profile1

  game of transformation-ESP-3DES-SHA10

  isakmp-profile sdm-ike-profile-1 game

  !

  !

  !

  !

  !

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet0

  Description $FW_OUTSIDE$

  IP address 93.166.xxx.xxx 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  outside the area of security of Member's area

  automatic duplex

  automatic speed

  !

  interface FastEthernet1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  interface FastEthernet2

  !

  interface FastEthernet3

  !

  interface FastEthernet4

  !

  interface FastEthernet5

  !

  FastEthernet6 interface

  !

  interface FastEthernet7

  !

  interface FastEthernet8

  !

  interface FastEthernet9

  !

  type of interface virtual-Template1 tunnel

  IP unnumbered FastEthernet0

  ezvpn-safe area of Member's area

  ipv4 ipsec tunnel mode

  Tunnel SDM_Profile1 ipsec protection profile

  !

  interface Vlan1

  Description $FW_INSIDE$

  IP 90.0.0.190 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  Security members in the box area

  !

  local IP SDM_POOL_1 90.0.0.25 pool 90.0.0.29

  local IP SDM_POOL_2 90.0.0.75 pool 90.0.0.90

  IP forward-Protocol ND

  IP http server

  local IP http authentication

  IP http secure server

  IP http timeout policy inactive 600 life 86400 request 10000

  !

  !

  IP nat inside source static tcp 192.168.1.200 25 interface FastEthernet0 25

  the IP nat inside source 1 interface FastEthernet0 overload list

  IP route 0.0.0.0 0.0.0.0 93.166.xxx.xxx

  !

  SDM_AH extended IP access list

  Remark SDM_ACL = 1 category

  allow a whole ahp

  SDM_ESP extended IP access list

  Remark SDM_ACL = 1 category

  allow an esp

  SDM_IP extended IP access list

  Remark SDM_ACL = 1 category

  allow an ip

  !

  exploitation forest esm config

  access-list 1 permit 90.0.0.0 0.0.0.255

  Access-list 100 = 128 SDM_ACL category note

  access-list 100 permit ip 255.255.255.255 host everything

  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything

  access-list 100 permit ip 93.166.xxx.xxx 0.0.0.7 everything

  Remark SDM_ACL category of access list 101 = 0

  IP access-list 101 permit any host 192.168.1.200

  !

  !

  !

  !

  !

  !

  RADIUS-server host 90.0.0.245 auth-port 1645 acct-port 1646

  !

  control plan

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  transport input telnet ssh

  !

  end

  Hello

  Looks like you're missing the key from the radius server configuration "RADIUS-server host 90.0.0.245 auth-port 1645 1646 key your_keyacct-port»

  Thank you

  Wen

• Changing the DNS server for ESX hosts?

  Our network administrator will change the IP address of the DNS server.  In this way, we will change those corresponding to ESX hosts.

  We would like to know

  (1) can we change the DNS server on execution of the ESX hosts without going into maintenance mode?

  (2) under what circumstances the ESX host will do use DNS servers?

  (3) memory, we should add all the IP addresses of ESX host in the hosts file in the Service Console, where is this hosts file located at?

  Thank you

  Tony,

  Use "service network restart" command to restart the network service

  Do not forget also that...

  Very dependent on DNS HA, HA will not work without the correct DNS configuration. The servers ESX and vCenter server must be able to resolve the name (FQDN full) / IPs in both feel to get a working HA.

• How to restrict Internet access by using the RADIUS server via switch Catalyst 3560

  Dear all,

  I need a configuration using any. I have a small network of 15 users a 3560, which is in turn connected to a router ISR 2811. Interface fastethernet 0/24 switch 3560 I intend to connect to a unix based server RADIUS. ISP is connected on the opposite side of the 2811 to the fa0/0 interface.

  I want to make is that if someone among the 15 users tries to access the internet, they must be validated in the RADIUS server by their pre-configured user credentials. (I'm going to store 15 user credentials here). If someone else tries to connect (except those 15) he or she should be denied internet access.

  The RADIUS server will be having a login page to type the name of user and password.

  Please guide based on what commands I should inject into the 3560 or what specifically, I need to have to run this task.

  Thanks in advance!

  Samrat.

  I only did this in a very long time, but you probably want to do is activate the web authentication.

  http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst3560/software/release/12-2_52_se/configuration/guide/3560scg/swwebauth.html

• Unable to connect to the radius server

  Hello

  I do configuration of the radius server on win Server 2008r2 wireless IEEE 802. 1 x.
  and I do the configuration on the access point to the RADIUS
  in win7 machine when I tried to connect to the server and enter the username and password that I created in AD, but win7 still asked me to username and password and it doesn't show me any error
  Please help me
  Thank you.

  Hello

  I suggest you to ask your question at the following link.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/

  I hope this helps.

• Test of the RADIUS server options

  Hello

  Does anyone have experience in the radius server availability tests? I have what the switch is used to test the availability of the radius server and what measures he will take after the detection of server are dead? Setup is done with ISE 1.4.

  Hello

  Because how switch contact RADIUS and how to configure the switch for dead timers, I will redirect you on the Cisco documentation which is very simple and complete as well.

  http://www.Cisco.com/c/en/us/products/collateral/iOS-NX-OS-software/iDEN...

  All parameters to mark a server as dead and how long it will be considered as dead are tweak-able. Setting dynamically some servers as dead if no responses may result in better performance of RADIUS response.

  Thank you

  PS: Please don't forget to rate and score as correct answer if this answered your question.

• Changing the vCenter Server IP address

  I am trying to build a new vCenter environment, we are currently waiting on IP ports and patch our networks team but I would "If I can" start building the server vCenter for this environment, there will be a virtual server.

  We have a test environment in place for the moment that we have a shared iscsi data store that once the environment has been built, we can remove from the inventory and add to the new environment once completed.

  Can we see problems with IP addressing if I build the server with a temp IP then import into my new environment and then change the IP address?

  Yes,

  As you say you have a DB server as physics that won't change, even if you go for the production.

  So, all that you requested

  (1) SSO - for SSO db if you use existing DB for this tha'ts then fine, but if you plan to have additional server to DB, you will find difficulty

  (2) SQL server for VC - as you said that you use existing DB... It is very good

  (3) installing vcenter server and inventory... require you to have details of the SSO server. If you use the IP agreement for the installation of VC, there is difficulty, where you must uninstall VC and inventory services.

  Kind regards

  Sachin Bhardwaj

• Newbie question on access to the RADIUS server

  I've worked before on RADIUS servers running on Windows but not on Unix. I'm new to an environment without any documentation and I make sure I have access to the GANYMEDE/ACS config.

  I go to my config switch and I see that ' 10.0.0.1 radius-server.

  Then I ssh into ' 10.0.0.1' and I see the below after "method.

  From the bottom, you have an idea on how to access the configuration of the ACS in case I need to change any setting it? I tried http://10.0.0.1 but it does not work.

  -bash-3, $00 ls
  bin features core net sbin TT_DB
  Start the etc. opt system usr lib
  export of CDROM lost + found tftpboot var platform
  dev House Dem proc tmp flight-bash-3. $00 ls
  bin features core net sbin TT_DB
  Start the etc. opt system usr lib
  export of CDROM lost + found tftpboot var platform
  dev House Dem proc tmp flight

  Try http://10.0.0.1:2002 for ACS listening on port default 2002.

  Pete

• After changing the IP Server Web host, the datacontrol to AMX page needs to be recreated?

  Hello

  I had deployed a Web service to a Server Web standlonee in my laptop, when I have at home or in the office, wlan ip address will change, so my app of the adf cannot get response of webservice except to build datacontrol based on Web server again, how I change the IP Address of the Web server host in the mobile application and do not need to create the new datacontrol again?

  Please help me! Thank you very much!

  You can change the IP address in the connections.xml file.

  More about this in the video here https://blogs.oracle.com/shay/entry/updating_adf_web_service_data

  about 05:20 in the video

• Considerations when changing the vCenter Server Unique ID?

  We have a minor problem with MAC address collisions, and to fix it, I want to change the ID of vCenter Server Unique from our "view" vCenter Server.

  (see KB1024025)

  However, I fear that there may be some side effects, of which I am unaware, and decided this time I would like to better ask before doing something stupid.

  Is it safe to change the Unique ID of a vCenter Server used by VMware View?

  Do I have to wait for any other effect that newly generated in another range MAC addresses?

  I have crossed a reinstall of my machine to vCenter using my existing db, but do not go back and change the ID Unique in what it was previously, and it caused no ill effects.  Having said that, for consistency, I made them the same thing.  I know that the ID to be used only for MAC and UUID, so there should be no problem.

  -KjB

• where to change the outgoing server

  Just put a ssl on my outgoing server and need to update the settings for the outgoing server. It seems that this function within thunderbird is incomplete. After some googling I was able to get to a place where I could drop to the bottom of all the servers, I entered, but the option to modify one of the existing servers wasn't in the drop down menu.

  Account of the actions dropdown also lacks an option to edit an existing account.

  If I click on manage identities I can find my user and click on 'Edit', however it brings me to the same choice window drop-down menu for which account I want to choose. It's funny because I pressed a button to change the settings of the account but never I was given a chance to change anything.

  So where should we do to change the outbound servers thunderbid?

  Open the account settings.
  Outgoing/SMTP Server is at the bottom of the left pane where all accounts are included. There is a button to edit an existing SMTP server.
  It is hard to Miss once you have the account of the Actions of the menu drop down.
  There is no option in the Actions drop account to edit an existing account. You can make changes directly in the window account settings for any server incoming which are listed there.

• How can I change the SMTP server to any server I want to?

  This is a common situation, and I have seen many others ask a similar question. It is a simple question, but Thunderbird does not seem to allow it. In my case, I have a choice of two mail server outgoing. I can use my hosting company Godaddy or my Internet provider, the local cable operator Charter Web. By default, Tbird uses the same mailserver incoming and outgoing, if possible, so my e-mail account has been configured to use the outgoing Godaddy server.

  I would prefer, however, to use the local server SMTP of Charter. But I can't find any way to change to that of Tbird. I could do it in Outlook Express, because both servers are listed for each e-mail account and can be changed.

  In Tbird, there is a drop down menu to choose an outgoing server, with no way to simply type in a new server. Or am I missing something? I think not, because others report the same problem. I have vague memories that awhile back, Tbird would you allow to specify all server to an e-mail account settings and then test their validity before finishing - a manual of against an automated way to set up an account.

  The main thing is I want to review the outgoing server of what I want, but it doesn't seem to be a way to do it.

  When your problem has been fixed can you mark the thread as "solved" Please?
  Thank you.

• Continues to change the proxy server setting in Windows 7

  I am running Windows 7 on a HP laptop and have a problem with the proxy server setting.  Internet usage has slowed because it tries to use a proxy server and I do not have.  I can access the settings and uncheck the "use a proxy server" box, but it becomes checked again in a few minutes.  How can I get there the way I put it.  I remember to hit the "OK" button when I do change.

  Hey Ed_B,

  I'm sorry that these documents did not help.

  Here is a document for the setting Internet Options Proxy Server will not stay off the coast, the following steps should resolve this problem.

  Good luck and have a great day!

• Change the DNS server automatically when switching to WiFi network?

  I am usually connected to one of the two wifi networks, one I have control on and I'm not. When I am connected to that I have no control over, I usually spend my DNS settings of the network server (which often breaks down) to a third party one, but I end up having to do this every time. Is there a way so that it would automatically change my DNS server whenever I connect to this network? I am running Windows Developer Preview

  Hello

  ·         What operating system do you use?

  ·         Your computer is on a domain network?

  Try these steps and see if it helps.

  Step 1: Run the network troubleshooter utility.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

   

   

  Step 2: Try to reset TCP/IP and check.

  http://Windows.Microsoft.com/en-us/Windows7/change-TCP-IP-settings

   

   

  Step 3: Uninstall and reinstall network/modem driver from Device Manager.

  (a) click Start, type Manager of devices in the search box and press ENTER.

  (b) Device Manager window opens, expand the network card.

  (c) right click and uninstall, reboot the system.

   

   

  Step 4:

  Follow the steps in troubleshooting from the link and check if that helps.

   

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

   

   

  Step 5:

  Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Reference: http://windows.microsoft.com/en-US/windows7/DNS-Domain-Name-System-frequently-asked-questions