Test symbol every time

Similar Questions

• PSC 1350 all prints a test page every time when turned on

  After changing the cartridge, we printed test page.

  Now, whenever we turn on the printer it prints test page automatically.

  How to disable this option?

  Thank you

  Hello vancat,

  If your problem is that your PSC 1350 prints a test page when it is turned on or after every printjob, it is very likely because the cartridge alignment process is not finished. After you have installed a new cartridge in the printer, it will print an alignment page. You must take this page and place it on the scanner glass (make sure that the top of the page is in a good way), then you press the "Scan" button on the printer itself. It will scan the page (that is, read the page) and full alignment process (so it is not scanning in the sense that it sends an image to the computer).

  I hope that clarifies the process of alignment slightly.

• How can I get my printer to stop printing a test page every time I turn it on?

  everytime I turn on my printer a page is printed. I would like to stop this.

  Hi TerriValenzuela,

  ·         What is the brand and model of the printer?

  ·         Did you the latest changes on the computer?

  I suggest you try the steps mentioned below and check if it helps.

  1. click on start, devices and printers.

  2. right click on your printer, select properties and all of the tabs look for a radio button titled "test page printed on startup."

  3. uncheck this option.

• short Smart self-test in tools hardware every time diagonestic is down and display alert (s5398d)

  show and short smart as self-test in tools hardware diagonestic every time is not the attention that my pc is model pavilion s5398d

  Looks like you have a bad hard drive. You will need to have the hard drive replaced and reload the operating system using HP recovery support.

• HP Deskjet 2132: Deskjet 2132 guard print page to test every time I want to print

  I just got this printer

  Whenever I go to print something on my printer, its tour and I don't know why, so when I have activate it and go to print an article, it shall decide on its own to print a Test Page first, all under its weight is to lose paper, it says its by aligning the heads, it should not have to align heads whenever I want to use

  How he stop doing that every time? , its boring and I cannot find any way to stop it in the settings menu

  Any help would be appreciated... Thank you... Jim

  Hi @JimDirt,

  Welcome to the Forums of HP Support!

  I see that your new printer HP DeskJet 2130 guard print a "test page" each time you print.  I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand how frustrating, it would be for you. It seems that alignment has not completed when you installed the printer at the start. The alignment sheet must be scanned or the process repeats. This is normal and it will continue to realign itself ended successfully.

  This guide illustrates the alignment process:

  • HP DeskJet printers 2130 - setting up printers
  Load paper into the paper feeder (make sure that you load into the fresh, unused paper tray).

  Load plain, US letter or A4 paper in tray after installing ink cartridges.

• How can I remove "the folder/Users/user/to/mygame doesn't exist." Terminal. Rises every time I launch Terminal.

  How can I remove "the folder/Users/user/to/mygame doesn't exist." Terminal. Rises every time I launch Terminal. I am a novice. Thank you very much.

  1. Please select from the menu bar Terminal

  ▹ terminal preferences... ▹ Profiles ▹ Shell

  If the run command box is checked, uncheck it or enter the command to run automatically (if any), each opening of a Terminal window. Note: this is not how you define a default shell.

  2. If step 1 does not resolve the problem, see below.

  Back up all data.

  Select

  New Shell command ▹

  in the Terminal menu bar. Uncheck the box marked

  Run the command inside a shell

  If it is enabled.

  Copy and paste the following line into the text box that appears, and then press return:

  /bin/mkdir disabled_shell_files

  Close the Terminal window that opens. Repeat with this line:

  /bin/mv .profile .bash_history .bash_profile .bashrc .inputrc disabled_shell_files

  History Shell and former initialization files will be saved in a directory named "disabled_shell_files" at the top level of your home directory. It is normal that some of these files do not exist, and therefore, you will get error "no file".

  Close the window and open a new test.

  You may already know that files with name starting in '. ' are not visible in the Finder by default. So, if you open the folder that you created in the Finder, it will appear as empty, even if it is not. If you need to recover a portion of the data in the files of the shell, use a shell such as nano-based text editor (1). Make sure that you're not recreating the problem. Otherwise, you can delete the folder.

• Firefox hangs at startup every time after the update. Windows 7.

  Crash ID: 95b523ae-2f5d-4766-8317-9b5092140723

  I've just updated firefox and now it crashes every time I try to open it. Even in safe mode.

  This looks like a problem with the garbage collection (GC).

  • Report of 31.0 Firefox Crash [@ JS::Handle < JSObject * >: operator JSObject * const & ()]

  These questions are usually not easy to diagnose.

  Start the computer in Mode safe mode with network support Windows (on the startup screen, press F8) as a test.

  • http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/

  Make a check of malware with several malware scanning of programs on the Windows computer.
  Please scan with all programs, because each program detects a different malicious program.
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender:
    http://Windows.Microsoft.com/en-us/Windows/using-Defender
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

• Satellite L20 260 won't boot to the top, every time it freezes with no reason

  Hi all

  I have a problem with my satellite of sad, after 3-4 days I installed a new operating system (tried with XP SP2 and Kubuntu) system does not boot to the top, every time it freezes with no reason, the only way is to perferom a new installation of the OS. What is a hardware problem, perhaps related to the RAM or HARD drive?
  x 10, Daniele.

  Hello

  It's not easy to tell if the problem is software or hardware related.
  You must install the OS from the Toshiba Recovery CD and again test the functionality

  If the laptop won't boot again freezes immediately after that installation of recovery CD, and then it could be a hardware problem.
  You can try using MemTest 3.5 tool.
  It checks the memory of a malfunction.

• Double layer burning fails every time - Tecra A9

  Hi all.

  My Tecra A9 is equipped with Teac DVW28ECT (Rev7.5A) I have no problem burning on a DVD single layer... but EVERY time I try to burn to a double layer process stops about 25% in the burning process.

  I can't find more recent updates of the driver/firmware for the dvd drive. I tried all brands of disk...

  Burning programs I use are up-to-date and are great for double layer / DVD9 disc production.

  Any advice of members who can help would be EXTREMELY appreciated!

  Hello

  I checked the manual and there is info that the laptop support DVD + R DL and DVD-R DL (format 1)

  But certain types and formats DVD-R DL and DVD + R DL disc may be unreadable.
  Also the DVD-R DL can be burned using the 2 x speed and the speed of 2.4 x DVD + R DL.

  Please see also the 90 user manual page.
  You will find information on tested DVD DL disc that are compatible with this laptop.

  Notes; the companies mentioned in the user manual are disc manufacturers one no suppliers!

• Why force eject hard drive every time?

  I have a MacBook Pro laptop.  When it is on my desk, I have a lot of things, including a backup disk, plugged.

  When I want to take my phone away from my office, I have to disconnect these things.  But, before I unplug the FireWire cable to the backup drive, I always first to eject the disc.  Sometimes I have to wait for Time Machine to slow down, then comes the ejection.  It is the way it works for years.

  Then last November, I upgraded from 10.6.8 in 10.11.2.  Now, every time - EVERY TIME - I press the little icon in a Finder window to eject the backup disc, up displays an alert:

  

  "Force eject" still works and is now part of my routine.  But it doesn't seem fair.  What is causing this extra step?

  Only time Machine should use this disk.  With the Finder, I see nothing that does not part of complex database of time Machine.

  I have not received all the Time Machine messages; a cursory inspection of the backup seems good.

  I tried typing lsof in the Terminal and haven't seen any strange open files. :

  lsof $ | grep Volumes

  Gil FolderAct 289 5r DIR 1,2 13353610 170 /Volumes

  I even opened a file on my disk backup, just to test that my order of lsof works:

  lsof $ | grep Volumes

  Finder 269 gil 24r REG 1.8 149158 692699/Volumes/Orange of the MBProHD/Backups.backupdb/MBPro/2016-01-08-090714/MBProHD/Install log backup

  Gil FolderAct 289 5r DIR 1,2 13353610 170 /Volumes

  I have an easy solution, but always this anomaly mind.

  Any suggestions?

  -Gil

  Try disabling Time Machine. Then, restart your computer. Then see if you can try to eject the disc as usual. If you can, turn on Time Machine. Try to eject the disc again. This may solve your problem.

  I hope this helps!

  Best regards

  Austin

• HP omni 200-5310 falls just crashes every time

  I have a desktop hp omni 200-5310 in allin one.

  It crashes every time when I play games on the internet or fifa12 and so on.

  When I tried to fix it I came up with a new question what is activex errors. I do not understand why it crashes every time.

  whenever I swith on my computer, then it blocks less than 45 min.

  How can I fix the accidents.

  When I asked assistance from hp to see my cmputer they just neglected. I also asked for a computer engineer. I've been waiting for 4 days but no response.

  one question what is activex errors

  Hello tantiya,.

  Thanks for the quick response!

  From the information that you have provided, I would as a result of this document on improving system performance without adding memory (Windows 7). This should help to improve the speed and effectiveness of your computer without adding memory (or RAM).

  If the problem persists, please follow this document on How to create a new account user in Windows Vista and 7. Once this new profile is created, please install your games to test and see if the computer will still crash. If it fell, I recommend creating a backup and restore of your computer. This can be done by following this resource on the backup of files (Windows 7), as well as this document theperformance of a system (Windows 7) HP recovery. This should help to restore your computer to factory settings.

  If the problem persists, please call our technical support at the 1-800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  I hope this helps!

  Best regards

• Read a data point every time via the sound card

  Hello!

  I'm reading the output of an amplifier to lock that cannot be connected to my PC. So I decided to read througn my mic.

  To do this, I connect channel 1 or 2 for my microphone.

  However whenever I do a reading I can not simply take a while but only several points at once.

  10 is the minimum number of points I can get when I put the sampling of 100 and length frequency 0.1 in the VI of its acquisition.

  Any combination that translates into less than 10 points gives me an error (for example 100 sampling rate and duration 0.01).

  I thought that by indexing dynamic data to acquire its VI would solve the problem, but playback is differnet from that I get when reading lock-in amplifier

  through GPIB.

  (I'm testing with a locking amplifier which I can via GPIB interface.  So at the same time, I read with my sound card and the GPIB and compare graphs)

  Any way to read a point every time?  Or I'm getting something other wrong here?

  Thanks for your time!

  Looks like the CDA min frequency response of 10 Hz, pg 69 card technical:

  http://www.hardwaresecrets.com/datasheets/ALC888_1-0.PDF

  However, you can apply a known value of low voltage DC at the entrance to see if it reads properly micro. Note that microphones out low level signals, looks like the ADC full scale entry is ~1-1.5V so make sure that your entry does not exceed. You can use dividers of resistive voltage if necessary to reduce the input voltage.

  -AK2DM

• Windows XP Pro SP3, OEM in Dell D600 "not responding" on every article, every time, all the windows

  My DELL D600 has OEM Windows XP Pro SP3, and netframeworks all or almost suddenly started not ANSWER DO NOT each time. I don't know what went wrong, it's driving me crazy. I can't afford to upgrade.

  I tried the fixit from Microsoft online, no luck.

  I uninstalled a few programs, perhaps thinking it's too full. Still no luck.

  Whenever I use any folder window, or any element of the queue at all, the same thing happens, every time. "Not responding" delays on the window or the desktop contains the item. Must hit Ctl + Alt + Delete at least twice, if not 3 - 4 times.  Each 'entry' lasts for a number of at least 26 and often much longer.  Basically, Windows is not very functional.

  I have two OEM for Dell, not sure that I put here (I was wondering if I should repair-installation Windows), but worried to destroy my Office Server installations that have 3 WordPress developments.  I can't afford to destroy the.

  Any ideas to FIX this would be greatly appreciated.

  Thank you.

  Good, minor success.

  The returned quickly file number, but a re - check with Roguefix showed, it was not clear, no change in System.

  I therefore decided to start uninstalling things, hoping to uninstall accidentally the culprit.

  First I stripped all the netframeworks and the SPs.  Has failed, file number remained.

  I then started to uninstall programs. After uninstalling programs a half-dozen, suddenly THE FILES ARE WORKING AGAIN!  Don't ask me why.

  Then, I rebuilt my netframeworks and SPs.

  Then, I clicked to access Microsoft Updater to get up to speed.

  IT WILL NOT BE UPDATED.  Failed! is what I get.  It says the software needed TO be updated is not in my HD and offer a download. When I try to download and install failed!  It will be not even installed that.

  This goes back to the same "cause" - for reasons unknown the last 4-6 weeks, installing any updates in my DELL D600 Windows XP Pro OEM.  Initially, they install.  Then begins the phase were some updates installed, others down without reason.

  Then, no updates would be installed.  That was BEFORE I plucked executives trying to solve the issue of records.

  It is not even asking me to install the real test happened before, I think that.  I think it was in August 2013 or almost.

  I'm desperate to get the updates, if you have an idea on how to help me.

  Thank you.

• Almost every time that I do a right-click to display a menu to do something such as delete or copy, the following error message appears: program internal error:.\Src\IntegrationToolsHolder.cpp,21

  Original title: internal program Errror

  I use XP Professional 32-bit.

  Almost every time that I do a right-click to display a menu of something for example delete or copy, you receive the following error message.

  Program internal error:.\Src\IntegrationToolsHolder.cpp,21

  If I click OK on the error message, it goes & I can then right click New & the appropriate menu appears and works correctly.

  Any ideas, please, as to what is the cause?

  Kind regards

  I told you I want to talk to you soon as you try these things.

  How to boot in Safe Mode and Clean worked for you?  Not at all useful?

  You said about this 2 weeks ago?

  Yet once, I fell in this place and the time and effort wasted because MS Answers forums invite to no system information when a new question is asked - but I digress.

  Update of security 908513 is included in Service Pack 3 update.

  Since forums MS Answers asks you any information from system when a new question is asked, we don't even know what Service Pack you have.  If you have SP3, you already have the update.  Two weeks and we don't know what is your Service Pack, what is your antivirus/antimalware environment...  We know that you have XP Pro 32-bit however.

  What you're likely to have is an extension of the Explorer Shell with a malfunction, and you can usually understand as follows:

  When the Windows Explorer (not Internet Explorer) is wrong (especially when right click), begin to suspect third-party add-ons explore extension.

  Those who would be the Explorer extensions that do not belong to Microsoft.  This means that extensions that you have added.  Solution Explorer extensions are generally well and installation of certain applications will install extensions from Explorer solutions for you, give you a choice and sometimes they can be added without your knowledge when you install the new software.

  Solution Explorer extensions are sometimes added as a new right-click option, you see on folders and files (like the scan of this file, open that file, play this song).

  If there is something in particular that you do during exploration that you know will be the cause of the problem, which will help focus on the problem and the help that you suddenly know, when you have found and corrected.  If you can get there when you want it, make an adjustment and then there is no message the next time you don't do anything, you do, you have found and corrected.

  If you can really achieve almost everytime you do a right-click and choose something like delete or copy, you're well on your way to understand.

  First of all you need a way to see what modules explore you have installed now and a way to turn them off (not uninstall them) so you can understand that we are at the origin of the problem.  You can have a lot of extensions not installed Microsoft don't even know you about.

  Download ShellExView here to see what Explorer extensions you have loaded:

  http://www.NirSoft.NET/utils/shexview.html

  ShellExView does not install anything on your computer, simply of runs and displays.

  After launching ShellExView, under Options, choose "Mark non-Microsoft Extensions" and extensions not Microsoft will be pink, clear, but on some systems which is a difficult color to see, so click on display, choose the columns and move the column Microsoft closer to the top, so you can see on your screen without having to scroll left and right.

  Click on the column header for Microsoft sort display (by clicking on the column of Microsoft) then all the non Microsoft extensions are on top and easy to see.

  Non-Microsoft extensions would be things you have added (non-Microsoft) and are what you should be suspect.

  You can also Google the name of a suspect add-on and see if there is any success about the errors with the extension and to what other people have done on it... Maybe just to get an update of the program that adds the suspicious extension.

  You can Google something like:

  Explorer XP crashing

  (you must complete your suspect on behalf of add on)

  See what kind of search results hits you get and are looking for solutions or situations that sound like yours.

  I'm not a defender of trial and error, but I can't think of another way to do...

  Right click and disable the extensions one at a time non-Microsoft keep a list so you can enable them again later if you wish. The result of the change is immediate and no reboot is necessary.  Test your failure condition.

  If you recognize all the extensions that have been added or recently downloaded, start with these first.

  Disabling the extension does not uninstall the extension - it is just disabled.

  Disable them one at a time until your right click on do not generate an error, then restart and test again.  You have disabled the last extension would be suspicious.

  You can also just disable all non-Microsoft extensions, restart and allow them one at a time until you find the one that generates the condition.

  The hope is that you will find an extension that caused the error, and then you can figure out what on this subject - either uninstall it or see if you can get an update of the author of the extension of their web page.

  I have not your problem, but I can when you toggle extensions, the extension is immediately turned off, to disable an extension does not require a restart, but if you find the problem, I reboot and retest in all cases to be sure that the problem has disappeared.

  If you post your non-Microsoft extensions list, maybe someone will recognize it as a potential problem.

  If you find the offending extension that's the problem, please let us know what it is that I can add to my list.

• Windows System 32 does not locate khatra.exe is move every time when I start my laptop that I have to remove khatra.exe from my laptop

  Windows System 32 does not locate khatra.exe is move every time when I start my laptop that I have to remove khatra.exe from my laptop

  Hello

  Information KHATRA.exe
  http://www.bleepingcomputer.com/startups/not_used-24897.html
  It can be made repeatedly in Mode safe - F8 tap that you start, however you must also run them
  the Windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone. (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also do to the General corruption of cleaning and repair/replace damaged/missing system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.