That's why my video after having made pale?

Similar Questions

• No video after having replaced the graphics card and power supply

  I have a desktop HP Pavilion m9515y PC. The graphics card that came with it (NVidia GeForce 9600 GS, 768 MB) did not suit the minimum specification required by a game that I played. Things in the game has been very slow - I could see a delay of s ~0.5 to move my mouse on the splash screen for the game.

  Today, I bought a new graphics (NVidia Geforce GTX 550Ti, 1 GB) card and a Corsair 700W PSU to replace the 350W one that came with the system.

  From the outset that I messed up something. It's been a while since I opened the box and I thought wrongly that the top panel (with the rubber surface) to come off before the side panel could be deleted. I removed the two screws now the top panel in place and slipped it in the process it disconnect and two thin black wires which I do not know the function. It was attached near the power button and one was attached to the rear of the Panel. The sons have stripped the ends rather than a connector of some sort and I don't know how they connect back or if they are the cause of the problem that I see now.

  In any case, I advanced and removed the old PSU and video card and replace them with the new. Two of them are significantly larger than the components, they replaced, but they managed to adapt with some maneuvers. All cards are well-placed in the PCI slots.

  The power is connected hard disk, DVD drive, the motherboard and the new video card. I'm not aware of any other connections that need to be made to food. There was not much clearance between the power supply and the back of the DVD player, but I was able to get the data and clinging to the DVD of power cables.

  After having done all that, I hooked my monitor DVI cable, plugged in the power cable and turned on the power. When I plug it in, the power button on the top of the tower is illuminated and the power seems to work. However, my monitor indicates that there is no video signal. I tried to put the old return video card, but I don't always have a video signal. Because I can't get a video signal, I can't tell if the PC is start or not.

  Does anyone know the purpose of the wires that were connected to the top of the Tower?

  They would cause they cause this problem if they are not correctly connected?
  Any suggestions for the possible causes of the absence of a signal from a video card?

  I just took the PC to a repair shop and it turns out that the problem was quite simple: I don't have the PCU power cable 4 pins hanging. Everything seems to start fine when we hung out at the shop. Fortunately, the place that I took did not even charge me what as they don't charge co-pays and since it is such a simple fix.

  Now I feel kind of stupid, but I know better next time...

• Different look of two of the same videos after having copied them.

  Hi community support.

  I copied a video (screen 1) a difference in sequence so that I can change it without losing the original that I created.  On the video copy I made my changes, and when I visited the new sequence of the video I noticed the video had black areas at the top and bottom (Screen Shot 2).  Why is this happen and how can I solve this problem.  I also noticed that the GSM logos have been distorted, I don't know how fix the logos, but also curious why it happened also.  Thank you for your time and help in answering this question.

  Randall

  

  There is a difference between the sequence the sequence #1 and #2 parameters.

  Access your source sequence, where you have copied the clip. Click anywhere in the timeline panel. Type the command + 0 {zero} to display the sequence settings.

  Check the dimensions of your pixels and the framework.

  Now pass your new sequence, where you have pasted clips and do the same for the new sequence. Compare the results.

  The screenshot you posted, it seems that your original sequence could have an incorrect Pixel Aspect Ratio.

  Unless you have specific reason besides, video HD should always have a Square Pixel Aspect Ratio:

  

  MtD

• The green bar on the half of the video after having been published in movie maker

  When I use windows movie maker to edit my videos everything seems good and when I save the bottom half of the video is transformed into a green bar. Why? What can I do to fix this? I use vista.

  When I use windows movie maker to edit my videos everything seems good and when I save the bottom half of the video is transformed into a green bar. Why? What can I do to fix this? I use vista.

  =========================================
  The info... copied on the net... may be useful:

  =====

  The Green problem bar setting in Windows Movie Maker
  http://www.bernzilla.com/item.php?id=884

  When I tried to follow the directions, I was unable to find XVid on my
  computer.  So I googled XVid and then (I think) the 2nd entrance to
  Download XVid.  After I downloaded it, I could follow the directions
  bernzilla and when I published a video - Voila! no green bar!

  After thick film Green line is published
  http://www.windowsmoviemakers.NET/forums/ShowPost.aspx?PostID=105025

  =====

  Good luck... John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Firefox unresponsive after restarting my computer after having made changes in the settings of the history and cookies

  I have some changes to cookies and erased my story for today... and then restarted my computer... now that firefox does not open... will not respond... should I uninstall firefox and then reinstall?

  If I uninstall firefox will be reversed the changes I made with cookies and my story?

  If I was to uninstall and reinstall firefox will lose my bookmarks if I do this? or firefox remembers them... so when I reinstall the previous bookmark is too reinstalled?

  Is - this Firefox starts when you open first after the computer restarts, but crashes the next time that you try to start? If Yes, then there is a bug in Firefox 29 where Firefox crashes out when the parameter ' delete history closing Firefox "is selected, so that you get an error" running but not responding do not "next time you ttry to launch. In this case, end the firefox.exe process in Windows Task Manager (or restart the computer) and then reset your Firefox Privacy options and UNCHECK the option «Clear history of Firefox closing» See this article for more details:
  Privacy, historical settings of navigation and-no-track

  If this isn't the problem and Firefox still open even after restarting the computer, then try to boot mode safe of Firefox by holding down the SHIFT key when you start Firefox. If Firefox starts then read Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to narrow down the cause.

• I have Windows XP Home Edition & tries to use Windows Movie Maker 2, after having made the film, he won't let m not record my movie?

  He's saying that he cannot save the movie to the specified location. Ensure that the use of original source of your movie files are always available (which they are!) that the backup location is always available - what it means?

  Pls help

  Thank you inadvance

  The most common reason, you see this is because Movie Maker is unable to manage one of your source files.  Movie Maker prefers to video .wmv and .wma for audio, so if you use other types of files in WMM 2.1, you should try to convert them to these types of files first.  Freemake has a couple of converters (Freemake Video Converter and Audio Converter from Freemake) that can do this quite easily.  Or you can look around.

  Another reason, you could see it is if your project has a lot of pictures.  The version of XP Movie Maker (WMM 2.1) was not too well manage memory and could not refuse to save your movie once it takes about 100 photos.  If this is the case, try to divide your project into two (or more) separate projects and recording each part as a separate sequence.  If it works, at the end you can put them back together by creating a final project and adding partial movies created previously.

• BlackBerry Smartphones Blackberry slow, 9900 after having made a transfer of 9300

  Hi I hope someone can help me with this.

  I have a BB 9300 curve, where I had a lot of problems with the phone is slow. When I sailed on the search option, he showed it - "yucvbm$ device research 'Laval'.

  When I got my bb 9900 I made the transfer using the desktop software and it seems to have yielded to the problems of my curve 9300 on my bold 9900. This problem is slowing down my phone in a big way and I was hoping that there is a fix for it? If this isn't the case, I'll have to re - install the phones software a format essentially?

  For any help or suggestion would be greatly appreciated.

  Thank you

  Ross

  Take a look at my post about restoring from an older model... leave the settings.

  (Sorry should have said - the title of the topic is - "requested facility not subscribed")-make sure that you have backed up your important documents, and then proceed to leave options - security - ticks and then type in blackberry in the box... expect that it restarts then use selective restore to only bring back your data leaving the settings stuff out.

• That is why my video blurry export?

  Hello

  Me a little here, a bastard. My short 33 second partial sequence of the timeline work playing great. That's when I export the problem occurs. I checked just as much as a human being, it takes, but no matter what I do, export comes out fuzzy. I've included a demo if anyone can help.

  The settings I know are:

  Premiere Pro CC2015

  Windows 8

  1280 x 720

  29.97 en

  Export:

  MPEG4

  Scale to fit (and fill up, as well)

  NTSC

  Level 3

  Go to verified maximum depth

  Maximum use invalidate verified quality

  Thank you very much

  Robert

  Hello

  Two questions. One, you have put your video export at a MUCH lower resolution (342 x 194) as your source (1280 x 720). In addition, MPEG 4 probably isn't the best format to choose in 2016. It gets a little confusing if you don't know much about codecs, but try by selecting the H.264 Format drop down. It gives you a video file that uses the H.264 codec super common inside of a MP4 container. It is one of the most common distribution methods on the Internet today. In most cases, you can leave the preset to "Match Source broadband." Hope that helps!

• safe to remove the recovery partition after having made discs?

  As the title suggests, made the recovery discs and want to use the hard disk space that is absorbed by the recovery partition.  Is it safe to delete them or will the lack of it on the hard drive cause problems with the recovery discs if ever needed?

  (G5135uk desktop HP just lowered from 7 to XP PC)

  In your case of removal of Windows 7 as the operating system and using Windows XP, I would say it is safe.  If Windows 7 was used, I would recommend to keep in tact.  If the recovery disks are used, it must put the computer back to factory new, even with the Parition of recovery went.

• How not to fix no sound after having made an optional update for conexant high definition smartaudio HD2, make it sound if go looking for manager__and device for hardware changes loose its restart the computer every time

  No sound after doing the update from microsoft for speakers

  Roll back the driver.
  In the future, do NOT use MSUpdate for pilots, drivers are taken, only if necessary, the manufacturer of PC or the manufacturer if a generic PC

• How to restore old favorites after having made a Firefox update?

  I did a Refresh Firefox to get rid of Bing (it worked). The Mozilla site said she would keep important things, but all bookmarks are gone.

  Sorry to hear about this. Here are two things to try:

  (1) to restore a backup of the bookmark. The following article has steps to call the restore function. If the backup is not available in your current Firefox profile (settings) file, they should be listed by date:

  Restore backup bookmarks or move them to another computer

  (2) restoring a backup file bookmark old data of Firefox on your desktop. Refresh moves your previous settings to a folder of old data of Firefox on your desktop.

  Do you see this folder? If so, please check inside a folder named semi-randomly and check the inside of a folder named bookmarkbackups. If you have, please use the article #1 above, but "Select a file" option to restore one of the backups in the folder on your desktop.

  A little luck?

• Why my computer is running so slowly after updates made this week

  * O.t. - recent updates

  Why my computer is running so slowly after updates made this week?

  Brenda

  The Windows Update process seems to require more patience than usual this month.

  Please provide more information for your issue to be diagnosed.

  Restart your computer and wait 20 minutes for the system to operate before you download information. When the review much, not Event Viewer log files all problems show in the period immediately after the computer has booted.

  Please provide a copy of your system information file. Type the system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. Not to place the cursor in the body of the report before exporting the file. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download the file to your OneDrive, to share with everyone and post a link here. Normal mode preferred report. Please say if the report was obtained in safe mode. If the report is in one language other than English, please indicate the language.

  Please download and share with everyone a new copy of your log System of your event viewer on your disc one and post a link here. It allows to avoid confusion if you delete all previous copies of the log files of your OneDrive.

  To access the system, log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window, expand Windows logs and select System. Place the cursor on the system, select the Action in the Menu and record all events like (the evtx default file type) and give a name to the file. Do not offer not filtered files. Do not place the cursor in the list of reports before selecting the Action from the menu. Do not clear the logs so that you have a persistent problem.

  For assistance OneDrive see paragraph 9.3:

  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm

• Since I loaded items 14 in my computer, the program stops working after having worked on the images and I try to save the processed images. This happens over and over again and I am very angry that this continues to happen. After working on an image

  Since I loaded items 14 in my computer, the program stops working after having worked on the images and I try to save the processed images. This happens over and over again and I am very angry that this continues to happen. After working on an image for 15-30 minutes I lose everything I did when the program stops working... This is extremely frustrating, as I can't use the program

  Hello... Adobe, you have a phone number I can call to talk about this?

  Why don't answer you my survey?

• How can you cancel the download of an update that was started by after having pressed the button "Check for Updates" in the window "On Firefox", please?

  How can you cancel the download of an update that was started by after having pressed the button "Check for Updates" in the window "On Firefox", please? If possible, please cover all platforms, Mac, Windows, Linux, although the first mentioned is what currently applies to my situation.

  Thank you.

  Such a download is usually recorded in a updates or updates folder in the program folder or the Firefox application.
  You can delete this folder to cancel the download.

  If the files have already been downloaded, then delete the files in the folder updates\0 and updates.

  • http://KB.mozillazine.org/Updates_reported_when_running_newest_version
  • http://KB.mozillazine.org/Software_Update

  Mac: /Applications/Firefox.app/updates "/path_to/Firefox.app/Updated.app"
  Linux: "/path_to/firefox/updated"
  Windows: C:\Users\<user>\AppData\Local\Mozilla\Firefox\Mozilla Firefox\updates
  

• Why did after downloading Windows security updates that Windows Firewall starts immediately after opening?

  Why did after downloading Windows security updates that Windows Firewall starts immediately after the connection?   This is happening with my PC and netbook, I almost hesitate to download the safety of dates in the future

  Hello

  1. What is the security update article?
  2. are there any other security software installed on your computer?

  If you have any third-party security software installed on your computer, I suggest you to disable the security software and then check if it helps.

  Note : If you need to temporarily disable the security software, you should reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks

  See also:

  The firewall service Windows in Windows XP Service Pack 2, in the edition of Windows XP Professional x 64, Windows Server 2003 SP1 and x 64 of Windows Server 2003 versions may not start if the DCOM Process Launcher Service is disabled: http://support.microsoft.com/kb/892504

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users: http://support.microsoft.com/kb/875357