The file or directory is corrupted or unreadable

Similar Questions

• received error 0 x 80070570 (the file or directory is corrupted and unreadable). __

  I tried to copy a file on my HARD drive on my HCSD card and received the error message 0 x 80070570 (the file or directory is corrupted and unreadable).
  HCSD card was used on an audio recorder, but I can play the majority of the file on the recorder itself. It's just that Win7 will not let me copy this file. Help, please. Thank you.

  0 X 80070570 - ERROR_FILE_CORRUPT

  If it relates to the wu or mu page, recommend to re - install activeX controls

  If it relates to the fix - then re - download the patch manually

• Error "Unable to create cache. The file or directory is corrupted or unreadable. »

  Original title: cannot create the ReadyBoost Cache

  Win7-64 bit-8gbRam use Flash drive for ReadyBoost cache HP16gb now receive the message: "unable to create the cache. The file or directory is corrupted or unreadable. "Should I delete the old cache file and try again, or is there another solution? Thanks for any comments.

  Well Ok,

  Run a check disk on the USB and see if it detects any errors.

  Refer to the article below for assistance.

  Check your hard drive for errors
  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7, Sysprep after getting an error "the file or directory is corrupted and unreadable."

  When I run Sysprep on this Dell Latitude E6520 with Windows 7 (x 64) professional, then boot into Windows PE to create a picture, he said "the file or directory is corrupted and unreadable."

  I made sure to restart 3 times before I ran sysprep this time because this is the 2nd time I got the error above.  Every time it reboots normally and the question obviously didn't happen until I ran sysprep.
  The last time I had to delete the partition and re - format and start over. Fortunately I took a picture of this time right front of sysprep.
  I even tried the Windows 7 installation disc to repair the MBR and the boot record, but he said he couldn't fix it, and he can't read this partition at all.
  I thought also it could be a bad drive on this computer brand new, but I ran the diagnostics on the hard drive and there are no errors.

  Because of the scope of your question, which is a professional information technology associate, its best that you publish in TechNet IT Pro forums to receive the best support for your question:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro/

• Receive the error "E: is not accessible. The file or directory is corrupted or unreadable.

  Original title: USBnot work

  Today, I inserted a USB key works perfectly in my laptop computer and got this message:

  "E: is not accessible. () The file or directory is corrupted or unreadable.

  Ideas of how this could be everything and no matter what suggestions how to fix it?

  I use an Acer laptop E1-522 (a new one that just came back from the manufacturer after warranty repairs and also had a technician called and insert a new hard drive because of problems with product key).

  I use Windows 8.1 and have used Internet explore and currently using Firefox as my browser (same questions with both browsers).

  Thanks in advance.

  Sorry, I don't remember the sequence that I used, but messages asked me to change the drive letter of the drive that I was using, so I changed it from E to F. He has not made a difference, because I always get a message "the disk is damaged or unreadable. Finally, I formatted, so I guess it should be the end of the story. I got lucky that didn't not lose all the useful data.

  Thanks for your help. I very much appreciate the way in which people help "technologically challenged" people like me.

• Reception: Z:\Preboot\utils\spi\spilib.pyc could not be copied; Error 1392 = the file or directory is corrupted or unreadable.

  Using Win XP Pro. While trying to make a backup on external USB disk, using rescue & recovery I get the message above. I've recently upgraded to rescue & recovery to the current version 4.21; The USB driver has been installed using the original version 1.00.00 RnR; Then this cause above corrupt or unreadable file or directory?

  Please, I beg you! can someone can help me with this? I would be grateful, thanks; HDS

  HeinrichDS

  Rescue and Recovery is, in my view, a Lenovo/IBM utility. Contact their tech support for help with their program; It is not part of Windows. MS - MVP - Elephant Boy computers - don't panic!

• Remove a computer record of the said cant "the file or directory is corrupted and unreadable."

  I get error 0 x 80070091 "the directory is not empty.

  Try to use Unlocker to: http://www.softpedia.com/get/System/System-Miscellaneous/Unlocker.shtml.  This program works often when normal functions remove Vista not work properly

  If this does not work, what is the exact path of the folder and the foldername (C:\Users\\Documents\Bad folder or something else)?  You can open this folder or it gives you a different error message (If Yes, what does EXACTLY)?

  Try bootingg in safe mode (repeatedly press F8 during the boot process until the menu appears) and then switch to this folder and tries to remove it from here normally, and then again using Unlocker.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• File or directory is corrupted and unreadable.

  In Windows XP Home Edition, I have a folder that I can't remove. This is the message I get: C:\Program\Norton 360 is not accessible. The file or directory is corrupted and unreadable. I tried to delete it using safe, run chkdsk f... How do I get rid of it so I can install Norton360?

  At first uninstall you it? Try the norton removal tool. I wouldn't install again. Its not terrible

• I get error: "the file or the C:\$Secure directory is corrupted and unreadable" after running chkdsk.

  I ran chkdsk utility and he stopped to say that I had a hard drive error or something like that. so I cancelled it. now I get all these things popping up that says ' the file or the C:\$Secure directory is corrupted and unreadable please run the chkdsk utility.» My question is if I run it again and it stops I have to do? I also need to know why I get the installer of windows popping up for office 2003, when I already have? I tried to reinstall with a drive, but my computer won't let me?

  original title: chkdsk utility
  original title: I ran chkdsk utility and he stopped to say that I had a hard drive error.

  I ran chkdsk utility and he stopped to say that I had a hard drive error or something like that. so I cancelled it. now I get all these things popping up that says ' the file or the C:\$Secure directory is corrupted and unreadable please run the chkdsk utility.» My question is if I run it again and it stops I have to do? I also need to know why I get the installer of windows popping up for office 2003, when I already have? I tried to reinstall with a drive, but my computer won't let me?

  What you need to do before anything else, it's everything and nothing important to you and to the stability of the machine (your ability to rebuild from scratch) backup because chances are - you will be rebuilding this computer from scratch and everything on this hard drive will be erased.

• All Applications have 0xc0000006 error, I can't update or run anything else and the system restore is unable to work because of error 0 x 80070570 (file or directory is corrupted and unreadable).

  I have a very new computer with Windows 7 Professional, and two weeks ago, he had a critical update.  Since then, McAfee has had problems.  I corrected McAfee, but yesterday, when I turned on the computer, I received a message that my windows is not genuine.  I accidentally clicked Ignore (or activate later) button instead of the activation button.  Now none of the software or applications to work and I can't get the computer to any previous dates because of the message: file or directory is corrupted and unreadable 0 x 80070570.

  I checked today and my Windows 7 is genuine.

  Many updates Microsoft Office cannot run also, since that time.

  How I fixed the 0 x error 80070570 and requests 0xc0000006 error?

  How I fixed the 0 x error 80070570 and requests 0xc0000006 error?

  Buy a new HARD drive . Your HARD drive is dying:

  //
  MessageId: STATUS_IN_PAGE_ERROR
  //
  MessageText:
  //
  The instruction at 0 x %p memory referenced to 0 x % the required data has not been placed in memory due to a State of error / 0 x %x.
  //
  #define STATUS_IN_PAGE_ERROR ((NTSTATUS)0xC0000006 L)

  Windows cannot read data from the HARD drive, that's why you got the errors.

  André

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Windows - message of corrupted file the file or directory c:\System Volume Information\_restore{106cf321-99A3-4E3A-9103-1BD02760-6A99}\rp687 is damaged and unreadable.

  the Information\_restore{106cf321-99A3-4E3A-9103-1BD02760-6A99}\rp687 Volume of c:\System file or directory is corrupted and unreadable. Run the chkdsk utility. I tried to run chkdsk but it does not work. I can't start the defragmentation either. I tried to run chkdsk on a restart and it does not start in safe mode it is running in read-only and shows errors but does not fix the

  You must run chkdsk with the "/ r", and/or switches 'f' for the errors to fix.

• This is the message I get: "the file or directory C:\Documents and Settings\ALLUSE~1\APPLIC~1\Norton\{0C55C~1\NIS_17~1.127\IRON is damaged and unreadable. Please run the chkdsk utility. »

  Original title: this is the message I get:

  "The file or directory C:\Documents and Settings\ALLUSE~1\APPLIC~1\Norton\{0C55C~1\NIS_17~1.127\IRON is damaged and unreadable.  Please run the chkdsk utility. "When I type chkdsk/f to the command prompt it tells me that it cannot run while windows is open and asks if I want it to work when I reboot.  I say Yes and restart and nothing happens.  What I am doing wrong?

  Hello

  1. when exactly you get this error message?
  2. don't you make changes on the computer before this problem?

  Check if the problem persists in the clean boot state.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

• Windows XP Setup error: the file ohci134.sys is corrupted?

  I was on my computer when my power cut off, and now it used to boot past the Windows XP loading screen, so I inserted the windows disk to run a chkdsk command or a repair, but I get the error: the file ohci134.sys is corrupted. Press a key to reboot the computer. »
  It won't let me access to the CD-ROM to install windows because of this error, and I can not boot past the windows loading screen! He's going to enter the safe mode options but whatever one I choose, it flashes a quick blue screen which says UNMOUNTABLE BOOT VOLUME. How can I fix?

  This is a nice article if it starts your desire to install the as option to start Recovery Console, your system and that you have a genuine XP installation CD bootable that corresponds to your installation.

  Here, the system does not start, there is no installation of the Console recovery and most people either have no real XP bootable installation CD or if they don't have one, it's older than their Service Pack installed.

  Unfortunately, we don't know anything about this system which is afflicted, except that it's a computer that no longer starts.  A little more detail would help, but that's the way things happen here in MS Answers forums.

  I just make a bootable CD of XP (no XP media required) Recovery Console and use it.

  Here's how:

  So, let's start with this:

  The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).

  These can cause corruption in the file system that must be fixed before you do anything else.

  If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).

  There is zero logic to begin to try to begin to try to modify or copy files to a hard drive that has a corrupted file system, so this must first be fixed using the XP chkdsk program and run chkdsk on your hard drives may solve your problem completely.

  Use the XP Recovery Console to check the file system on your HARD drive and fix the problems and then try to start your system - this may be all you need to do.  Or, you are welcome to just start trying things that might work.

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Error - Installer: wrapper. creatFile failed with error 123: the file name, directory name or volume label syntax is incorrect when installing any program.

  Original title: there is an error then that inistalling some programs such as, java, internet download manager and...

  There is an error then that inistalling some programs such as, java, internet download manager and...

  for example, I want inistall an application or a program like Java, but when I start to inistall, it works like adminstere then said: (Installer: wrapper. creatFile failed with error 123: the file name, directory name or volume label syntax is incorrect.)

  It even I mean to inistall Internet download manager and VLC...

  my pc is automatically updated and when updates are available whenever I download inistall,.

  Please help me, I love my windows Vista, tnx

  Hello Aliahriman,

  Please look at the post below and see if it will solve your "creatFile failed with error 123: the file name, directory name or volume label syntax is incorrect" question.
  He has helped others with a similar issue.
  http://social.answers.Microsoft.com/forums/en-us/VistaInstall/thread/3b180316-95c2-4613-8c38-8515481db22c

  If please reply back and let us know if this helps solve your problem.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• When I try to run system repair ffrom originally Vista 32 bit dvd, I get the error "the file i2omp.sys is corrupt"

  Original title: when I try to run the system repair ffrom the original Vista 32 bit dvd, I get the error "the file i2omp.sys is corrupt" is anyone know the solution for this problem? Thank you, Kelsey.

  The message arrives as soon as I select "repair system" can not find the file on the Windows Dvd.

  Hello

  1. why you try to run the system on your computer repair?

  2. when exactly you receive this error message?

  If you receive the error message while booting from the Windows Vista DVD it means that the file i2omp.sys is corrupted.

  You may need to make arrangements for a Windows Vista disk that corresponds to the same edition, as it is installed on your computer. Later, try to repair the system on your computer.

  How to replace Microsoft software or hardware, order service packs and replace textbooks?

   
  Reference: What are the system recovery options in Windows Vista?

  Hope the helps of information.