The host agent GBA support
What version of ACS that supported for the host agent (for example IP phone, printer, etc.)?
I have GBA v3.1, it is supported?
Is there a solution to authenticate devices by MAC address?
Thank you
AW
Configuring the host agent is supported in 4.2 and ACS version 4.0,4.1. Many guests who authenticates the ACS are running the agent software that requests access to network resources and receives approval from the ACS. However, some hosts are not the agent software running. ACS solves this problem by using the MAC address of the host device to identify and authenticate the host. This technique is called the authentication MAC (MAB) workaround.
Tags: Cisco Security
Similar Questions
-
Hello
I tried to get VMWare Server 2 to settle, (Windows Vista Business, SP1, Internet Information Services running, SQL Server 2005, 2008...
and everything I try, I get error 25011. Cannot configure the host Agent Service.
(The old Console server ran very well, only a few months ago, I can not connect with it to remote machines)
Any suggestions would be welcome!
Thank you
Janos
Hello
Try:
1 uninstall WMServer (you can clean the reg file)
2. stop the IIS services
3. install VMServer
4. start IIS if you need it.
J.
---
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
-
Regarding the hosts took max supported on Vcenter Virtual Appliance 5.0
http://www.VMware.com/PDF/vsphere5/R50/vSphere-50-configuration-maximums.PDF
Maximum config guide indicates that vsphere 5.0 supports the hosts of 1000 per VC. The same applies to the virtual appliance thus (on an external Oracle DB... not the one internal)
Concerning
Girish
The same should apply to the device when you use an external database. But with several guests it would be wise to take the same settings with the Windows version of vCenter, which means increase the memory of tomcat and adding vCPUs additional and resources of the virtual machine RAM.
-
ESXi4.1 - the host is not supported VT - i7 720Q
Hello and thank you for taking the time to read my question.
This is a test environment, proof of concept, etc. We have an i7 720Q which is a hyperthreading processor. ESXi is installed in VMWare Workstation. ESXi processor is defined on Intel VT - x. I can't create 64-bit with vsphere hosts. I get the message "this virtual machine is configured for 64-bit operating systems. However, the 64-bit mode is not possible. This host does not VT support"I can run the 64-bit very well within VMWare Workstation operating system, just not in ESXi in workstation.
Ideas?
Thank you
Chase
VT is a hardware device that is not passed through a virtual machine. Therefore, it is not possible to run the OS 64 - bit guest nested within your VM ESXi.
André
-
How to find OEM agent House?
I need to install the agent in OEM grid again on the DB server and register again in OEM. Can anyone tell please the steps to do it?Assuming that he is an agent of 12 c pre EM on a non-Windows platform, you can find an entry for the House of the agent in/etc/oratab or/var/opt/oracle/oratab depending on the operating system platform.
The following entry of oratab sample showing the Oracle home for the agent's / u01/oracle/agent11g:
*: / u01/oracle / agent11g:NTo uninstall an agent, see:
http://docs.Oracle.com/CD/E11857_01/install.111/e16847/part_deinstall_slnt.htm#sthref435To install an agent, see:
http://docs.Oracle.com/CD/E11857_01/install.111/e15838/install_agent_usng_console.htm#CACJEFJINote: If the agent and its targets monitored are still in the repository (for example, the console still shows them), you can remove them before reinstalling the agent to avoid having download due to duplicate targets problems later.
Kind regards
-Loc -
Cannot start the VMWare host agent service
I worked on this issue for awhile with no resolution. Initially, I had a problem running VMWare Server Home Page so I installed the VMWare Server Console and the error when trying to launch the Console VMWare Server on the same server VMWare Server is installed and connect locally:
501 command overall GLOBAL Server-vmdb targets no host agent not supported.
Came to the conclusiong that it was the result of the function of Agent Host VMware is not able to start.
Environment:
IBM BladeCenter HT chassis
IBM eServer HS21 - 8853AC1
NetXtreme Broadcom5704S
2 x Quad Core Intel Xeon E5440 2.83 GHz
Initially, I installed VMWare Server 2.0 and then upgraded to 2.0.1 to see if that would solve the issue but always without success.
Event Viewer message:
Host VMware Agent service terminated with service specific error 4294967295 (0XFFFFFFFF)
Not tried so far:
I tried uninstalling and reinstalling several times without success
Tried to manually start the VMWare host Agent
Tried the upgrade to VMWARE 2.0 VMWARE 2.0.1
Tried to uninstall and reinstall
Tried to launch the service as ADMINISTRATOR
It is the only VMWare Server service that does not start... I Googled, and I can't find a resolution to this problem.
Post edited by: RDPetruska
Emoticon removed from the subject line.
Check this solution or search the Internet: "panic error: not well formed (invalid token)" (sorry, I don't have the time to search for you now).
BTW. If IIS is installed and running, try to stop and start the vmware agent
J.
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
Post edited by: janlib
-
Host Agent VMWare fails to start - how to start?
How can I start this if she fails to start automatically? I just upgraded VMware 1.01 to 2.0 and will have a little trouble with my system error newspaper have reported this fault, which I believe, other threads may be the cause of my browser does not connect to the remote server. Also, I installed VMWare Server2.0 but did not receive a prompt at any time for my License key, this will happen after I get the host agent VMWare started?
Try to create a new empty virtual machine and turn it - if you can do that, then you have a valid license.
You can see which license you have entered by clicking on the 'Application' menu, then "enter serial number" when the host is selected according to the directives of the attached screenshot.
---
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
-
Dear team,
I am facing a problem when setting up the AP on a single server. Scenario is the following:-
Six months back I install the VMWare solution for our Organization. ESXi 4.1 is. At this time there were two servers in the cluster, and both have been configured with HA successfully.Now, I have a server added more in the Cluster, but when I'm trying to configure the AP on the same system, it gives the error "cannot complete the configuration for HA agent on the host computer.". Another HA configuration error. "(Screenshot attached) so many times I click with the right button on the server and select reconfigure VMware HA but failed.
Could someone help me please. It is a live system and the knot very critical. If need help on an urgent basis.
But in addition, we also bought a 1 year (TS) technical support for our prodcut. Could someone please guide me how can I get a ticket for it.Thank you and best regards,
Gaurav Asthana
Hi all
Thank you for your kind support. My problem is solved and it is very simple. By turn off and turn on again the HA on the Cluster setting, the problem is solved. All servers are now configured HA.
Thank you again...
Gerard
-
I use Foglight 5.6.5 and I was wondring where, in the dashboard - we can see the foglight agents associated ip addresses. There are many times we need the ip address of a host, I want to add a custom dashboard if necessary to include this
George, was the question that you asked:
"How can I find the IP addresses of remote hosts being monitored?
or
"How can I find the IP address of the FGLAM server that is monitoring?
-
"No 3d support is available from the host"
Program: Job 12
Operationg System: windows 7 Professional K service pack1
Graphics card: GeForce 9600 M GS
I saw the message 'no 3d support is available from the host'I don't know this solution.
I need your help.
How can I solve this problem?
You can specify... is your operating system Windows 7, or you are running WIndows 7 in a VM on something else?
Make sure you have the latest video drivers.
If you use windows, make sure that hardware acceleration is turned on.
If you see no problem and everything works, then ignore it.
-
We receive an error message that I am trying to make sense. I understand very well the notion of compatibility, CPU, CPUID, masking and so on, after working on a competitor hypervisor. However, this error seems wrong (or needs better wording) based on my understanding:
Here is the message:
----
A general error occurred: the version of the product to the destination host does not support one or several features of the CPU currently use by the virtual machine.
Characteristics of CPUID level 0 x 1 'ecx' register are indicated with a '1' bit: x00x:xxx0:xx0x:x 000: x 0 11xx:00: 00xx:11xx
----
This happened during the migration between two hosts ESXi with the same physical processors - in this case, a Westmere X 5650.
The source host is on ESXi build 2068190 (5.5). The destination host is on ESXi build 1474528.
The bits it seems to complain are:
DTES64
Monitor/MWait
Cx16
PDCM
The punch line seems to be: "the product version of the destination host. However, I have trouble believing that support for these features have been added to ESXi between the two versions. If it were, VMware has been certainly silent about.
For what it's worth, explicitly set us the CPUID masks in our virtual machines (no, CVS is not an option for us at this time.) This is the mask:
CPUID.1.EAX = "00000000000000100000011001010001".
CPUID.1.ECX = "00000010100110001110001000111111".
CPUID.1.EDX = "10001111111010111111101111111111".
CPUID.80000001.ECX = "00000000000000000000000000000001.
CPUID.80000001.EDX = "00101000000100000000100000000000".
cpuid.d.EAX = "00000000000000000000000000000000".
cpuid.d.ECX = "00000000000000000000000000000000".
cpuid.d.EDX = "00000000000000000000000000000000".
Note that the bits of the message complains (2, 3, 14, 15) * are * in fact forced to '1' in our mask of cpuid.1.ecx. That means (if I understand correctly), ESXi does not have the virtual machine unless the host processor supports the feature. And in our case, the virtual machine will start with happiness on nodes, with both versions. It will be not simply migrate between them.
So, long story short, is this a bug of ESXi? The error message is misleading? I understand something?
Thank you
MattTo use the masks feature VM in this way, you must replace all the 1 to your masks with-'s:
CPUID.1.EAX = "00000000000000-000000 - 00-0 - 000-
CPUID.1.ECX = "000000-0-00--000---000-000---".
CPUID.1.EDX = '-000 - 0-0 - 0-
CPUID.80000001.ECX = "0000000000000000000000000000000 -"
CPUID.80000001.EDX = "00-0-000000-00000000-00000000000.
cpuid.d.EAX = "00000000000000000000000000000000".
cpuid.d.ECX = "00000000000000000000000000000000".
cpuid.d.EDX = "00000000000000000000000000000000".
Zeros erases the features that are not available on your hosts Westmere, and dashes will leave the other one features. The problem with those masks was forced to you certain features on who would have normally been off.
-
Virtual machine has 12 virtual processors, but the host only supports 8?
Hi all I am using ESX 5.1 and have a machine Windows 2012 R2 Standard of virtual (vmx-09) comments that I'm moving to 8 processors to 12 processors. But when I turn on the virtual machine after changing the UC 12 I get the error message
"Virtual Machine has 12 virtual processors, but the host only supports 8. The number of virtual processors can be limited by the selected guest OS for the virtual machine or the granting of licenses for the host".
Now, I know that 2012 R2 Standard Windows can handle 12 processors and I thought that ESX 5.1 could also, but I'm wrong? This is the Standard of vSphere license 5. Thank you!
Hello
vSphere 5.1 Standard license has a 8 vCPU per VM limit.
Company = 32 vCPU
Business + 64 vCPU
You must upgrade to vSphere 5.5. This can be done with your vSphere license 5, as it is for all versions 5.X of vSphere and vCPU limit has been deleted in 5.5.
So you can have as many vCPU per VM that your host has logical cores.
Tim
-
Dear team,
I want to devote 8 vcpu to one of the virtual machine, but it gives following error
"Virtual Machine has 8 virtual processors, but the host supports only 4. The number of virtual processors can be limited by the selected guest OS for the virtual machine or the granting of licenses for the host".
want to know the weather, that it depends on the os under license or guest vm
Hello
It is the restriction of license. 4-way vSMP is the right thing, you stressed in your screenshot.
If you upgrade your server and license to vSphere 5, you can allocate 8 vCPU with Standard license and 32 vCPU with your license of the company!
Concerning
-
Hola y buenos dias, he puesto 2 hots directly in una DMZ y al activar el error HA da este:
"Unable to complete the configuration of the ha agent on the host computer.". misconfiguration of the installation of the host network.
ESTOS son gemelos servidores y poner esta durante 2 Años last config antes han estado dentro infraestructuras en a cluster con otros 4 running perfectly. Ante nueva situation that met responsible security perimeter solo our esta posibilidad por lo as procedimos dio el a preparar los hots ante the nueva config enchufamos estos y an el swhitch of the demilitarized zone.
Según me ha EDI el responsible of security perimeter, todo el trafico desde estos 2 hots hasta el esta allowed vCenter y asi mismo el cortafuegos responde al trafico ICMP a estos hots (este tema that he read in various Québec sites are important para el HA).
Version of hots los Esxi 4.1.0 721871
Me falta algo o tengo algo configurado evil?
Important Algo a revisar?
A greeting is gracias por adelantado
Buenas
Me designed that tendras 2 con 2 direcciones distintas vmkernel (lo del tema Las vlan y las tarjetas're menos ahora lo)
Prueba has see the resolución desde el propio ESXi, prueba el uno a otro por both vmkernel ping, etc...
A malas, saca ambos nodos del cluster y vuelve a unirlos con desactivado, cuando tengas los 2 HA, activa HA of nuevo y con eso you can smear of dudas so por el tema del VC University y UN vicio en BBDD.
If todo esto falla, have as plantearte touch en el aam, are fairly complejo y peligroso if no to sabe hacer correctamente.
-
Hola y buenos dias
me esta dando este error cuando a UN con cluster 2 hots the digo el HA assets. There buscado por internet y the mayoria of las hacen referencia a lo mismo responses:
The config of VMware high availability (HA) falla con el error: unable to complete the configuration of the HA agent on the host
- Select turn on VMware HA, luego elija VMware HA desde el cuadro of the izquierda.
- Select Advanced options.
- Adicione opcion das.bypassNetCompatCheck con el valor 'true '.
- Haga click OK in the options advanced, luego haga click en OK again pantalla para aceptar los cambios in el cluster config.
- Hope a todos los servidores ESX in el reconfiguren HA cluster.
El tema are that he made lo go y sigo don't con el mismo error y no lo tengo claro what me escapa.
OS explico mi arquitectura
Cluster development: 2 hots ESXi HA con 4.1U1 en mi red (the same as el vCenter)
Maybe you are looking for
-
Can I save or export passwords saved with Firefox in order to get back them in a new computer?
I will soon get a new computer. Having a large number of websites and passwords saved in Firefox Mozilla respective access, it would be very convenient to be able to export this information to the new machine after installing Firefox, as you can do w
-
I just ran the Windows 7 Upgrade advisor, and he said I should remove the ATI catalyst install manager and the control centre and reinstall them after installing windows 7. How would I do that? All the tips are greatly appreciated.
-
HP probook 6570B: e-mail software
Hi I just got an email and want to know if it is authentic or spam question is what I download it? http://h20566.www2.HP.com/hpsc/doc/public/display?docid=c04680732
-
How we change admin.on a used computer that I bought at a yard sale?
I bought an IBM computer at a yard sale and a former administrator there. How can I change the administrators in order to change the settings and do other things that only an administrator can do. Accounts new passwords, etc... Help, please. It stuck
-
HP Pavilion p2: System Restore
Good afternoon My name is Alan Garza and I'm trying to restore it to its factory of my computer settings. It's a Hp Pavilion p2. I don't want something to be saved or to be as it is now, I want it to be as if I just pulled it from the box. How can I