ESXi4.1 - the host is not supported VT - i7 720Q

Similar Questions

• Cannot migrate VM between 5.5 ESXi versions: the version of the product to the destination host does not support one or several CPU features

  We receive an error message that I am trying to make sense. I understand very well the notion of compatibility, CPU, CPUID, masking and so on, after working on a competitor hypervisor. However, this error seems wrong (or needs better wording) based on my understanding:

  Here is the message:

  ----

  A general error occurred: the version of the product to the destination host does not support one or several features of the CPU currently use by the virtual machine.

  Characteristics of CPUID level 0 x 1 'ecx' register are indicated with a '1' bit: x00x:xxx0:xx0x:x 000: x 0 11xx:00: 00xx:11xx

  ----

  
  

  This happened during the migration between two hosts ESXi with the same physical processors - in this case, a Westmere X 5650.

  
  

  The source host is on ESXi build 2068190 (5.5). The destination host is on ESXi build 1474528.

  
  

  The bits it seems to complain are:

  
  

  DTES64

  Monitor/MWait

  Cx16

  PDCM

  The punch line seems to be: "the product version of the destination host. However, I have trouble believing that support for these features have been added to ESXi between the two versions. If it were, VMware has been certainly silent about.

  For what it's worth, explicitly set us the CPUID masks in our virtual machines (no, CVS is not an option for us at this time.) This is the mask:

  CPUID.1.EAX = "00000000000000100000011001010001".

  CPUID.1.ECX = "00000010100110001110001000111111".

  CPUID.1.EDX = "10001111111010111111101111111111".

  CPUID.80000001.ECX = "00000000000000000000000000000001.

  CPUID.80000001.EDX = "00101000000100000000100000000000".

  cpuid.d.EAX = "00000000000000000000000000000000".

  cpuid.d.ECX = "00000000000000000000000000000000".

  cpuid.d.EDX = "00000000000000000000000000000000".

  Note that the bits of the message complains (2, 3, 14, 15) * are * in fact forced to '1' in our mask of cpuid.1.ecx. That means (if I understand correctly), ESXi does not have the virtual machine unless the host processor supports the feature. And in our case, the virtual machine will start with happiness on nodes, with both versions. It will be not simply migrate between them.

  So, long story short, is this a bug of ESXi? The error message is misleading? I understand something?

  Thank you

  
  Matt

  To use the masks feature VM in this way, you must replace all the 1 to your masks with-'s:

  CPUID.1.EAX = "00000000000000-000000 - 00-0 - 000-

  CPUID.1.ECX = "000000-0-00--000---000-000---".

  CPUID.1.EDX = '-000 - 0-0 - 0-

  CPUID.80000001.ECX = "0000000000000000000000000000000 -"

  CPUID.80000001.EDX = "00-0-000000-00000000-00000000000.

  cpuid.d.EAX = "00000000000000000000000000000000".

  cpuid.d.ECX = "00000000000000000000000000000000".

  cpuid.d.EDX = "00000000000000000000000000000000".

  Zeros erases the features that are not available on your hosts Westmere, and dashes will leave the other one features.  The problem with those masks was forced to you certain features on who would have normally been off.

• "Your host does not support the current settings for comments.

  My requirement of virtualization are demanding very high resolution on a Win2000, ESXi host guest.  I upgraded, using the stand-alone version of converts, but I can no longer switch to full-screen (the scale).  I get the following message:

  -

  ---

  Error

  -

  ---

  Connection error: your host does not support the current settings of comments in mode full-screen.  Try to reduce the color depth or resolution of your guest and try again.

  Impossible to enter full screen mode.

  Do you want to retry?

  -

  ---

  Yes No

  -

  ---

  Does perform a work around?

  Thank you

  Alan

  The vSphere client is a terrible Viewer. Very slow. W2K is also a limitation. Take a look at the other viewers if RDP is not suitable. Radmin is one I've used several years ago.

• Windows ip configuration is an internal error: the request is not supported

  I cleaned up a few viruses out of a Windows XP Professional computer to a customer, and now he can't go on the internet.  When I check ipconfig, I get the following error.

  Windows IP configuration
  An internal error has occurred: the request is not supported.
  Contact Microsoft technical support for more help.
  additional information: host name of request impossible.
  So I googled some results. Have replaced the TCPIP.sys file with one from another computer, I still get the same message.  I don't have a windows XP original disk to put it into recovery mode.
  I also ran the command "netsh int ip resetlog.txt" but which did not help either.  I saw on another blog.
  The NIC is to see that there is a power cable plugged into it as well.  Help, please!
  Thank you
  Trever

  Hello Trever,

  Follow the methods and check:

  Method 1: You can refer the following Microsoft Knowledge Base article and check.

  "Error 1068" error message when you try to enable Internet connection sharing

  http://support.Microsoft.com/kb/827328

  Method 2: Try the SFC (System File Checker) scan on the computer.

  To run the System File Checker tool, follow these steps:

  a. click Start and click run, then type cmd in the box start the search.

  b. right click on cmd in the list programs, and then click run as administrator.

  c. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  d. at the command prompt, the following line and press ENTER:

  sfc/scannow

  For more information, see the article:

   

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  http://support.Microsoft.com/kb/310747

   

  File system (CFS) Checker

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/system_file_checker.mspx?mfr=true

  Let us know if that helps.

• Linked clone failed: the operation is not supported on the object

  Hi all - I would appreciate help on a related clone operation that is a failure.

  I use Quest vWorkspace to create linked clone VM in my environment.  It integrates with virtual Center and creates from a VM snapshot parent according to normal related clones.  It has just stopped working and I am trying to track down the cause.  The task fails with the error message in the console of VMware vCenter: the operation is not supported on the object.

  The vCentre is 5.5 and esxi.  vWorkspace is v8.0 MR1.  The parent VM is located on an iSCSI datastore.  I tried to put the clones of destination on premises and warehouses of NFS data with the same result.  Unfortunately I can't (don't want really to) move the VM parent from the data store that I have of many VM related to this virtual machine.

  The failure message is a bit generic, so I looked on through the vmkernel.log and vpxa.log and it is an excerpt from the vpxa.log whereby it shows failed task 153.  Can someone please indicate something in the newspaper that had to be examined or another newspaper to look at?

  vWorkspace attached error and below:

  Linked clone has not CreateLinkedClone_Task of CloneVmLinked failed! Task of VMware CreateLinkedClone_Task status error - the operation is not supported on the object. -Call stacks-VmLinkedClone.VmLinkedCloneService.CloneVmLinked String vmInvPath, String strSnapshotMor, String strNewVmName, String strSysprep, ManagedObjectReference morFolder, ManagedObjectReference morResPool, ManagedObjectReference morHost, String strDatastoreName, Boolean bQuickPrep, String domainNameIP, String

  See attachments

  Thank you very much
  Wikus

  Additional accessories:

  • 
    Untitled picture.png

  Hello guys,.

  For those of you already on 5.5, I did a few tests these days. I did find a magic bullet yet as a single parameter that is sure to break but I came up with a workaround.

  I found that if my ESXi server was still on the 5.1, vWorkspace could deploy clones linked via vCenter 5.5 - it's only when the ESXi is also on 5.5 that you have a problem.

  If any of you have ESXi hosts still on 5.1, you can deploy there for now.

  In ESXi 5.x, it is easy to have an ESXi virtual machine. You might want to consider creating some virtual boxes ESXi to deploy on while the vworkspace dev team look at why it does not work.

  I know that this is not the best solution in the world, but it's better than no work around

  Thank you, Andrew.

• The host agent GBA support

  What version of ACS that supported for the host agent (for example IP phone, printer, etc.)?

  I have GBA v3.1, it is supported?

  Is there a solution to authenticate devices by MAC address?

  Thank you

  AW

  Configuring the host agent is supported in 4.2 and ACS version 4.0,4.1. Many guests who authenticates the ACS are running the agent software that requests access to network resources and receives approval from the ACS. However, some hosts are not the agent software running. ACS solves this problem by using the MAC address of the host device to identify and authenticate the host. This technique is called the authentication MAC (MAB) workaround.

• Reviews operations - the operation is not supported

  Hello

  I use vmware.vim api in a c# project. When I try to get the GuestAuthentication with AcquireCredentialIsGuest object, I get the following error:

  "A NotSupported server of type error with the message"the operation is not supported on the object."occurred during the requested operation operation."

  Orders are not disabled, virtualmachine, or on the host. I'm running out of ideas what could be wrong. Can someone help me?

  Code:

  GuestOperationsManager t (GuestOperationsManager) = customer. GetView (customer. ServiceContent.GuestOperationsManager, null);

  GuestAuthManager c = customer (GuestAuthManager). GetView (t.AuthManager, null);

  NamePasswordAuthentication userCred = new NamePasswordAuthentication();

  userCred.Username = "xxxx";
  userCred.Password = "xxxx";
  userCred.InteractiveSession = false;

  GuestAuthentication a = c.AcquireCredentialsInGuest (vm. MoRef, userCred, null);

  Thank you!

  Hi Méteron,

  If I understand correctly it train physicians AuthManager.AcquireCredentialsInGuest we are not allowed to use NamePasswordAuthentication with this method. Instead try to pass an instance of NamePasswordAuthentication directly to the method that requires authentication and do not GuestAuthManager at all.

  Hope this helps :-)

• The host has not enough space on the boot partition to store the image upgrade. It takes a minimum of size_in_MB. After the release of space or perform an installation from the CD-ROM.

  Hi everyone, the difficulties in trying to update the Update Manager. ESX4.1 to ESXi5.0

  Error I get is below to correct the scan before update:

  The host has not enough space on the boot partition to store the image upgrade. A minimum of 299MB is necessary. After the release of space or perform an installation from the CD-ROM.

  There is enough space in the local disk

  Size of filesystem used Avail use % mounted on
  / dev/sdd5 4.9 G 1.6 G 3.0 G 35%.
  / dev/sdd2 2.0 G 107 M 1.8 G 6% / var/log
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / Boot
  / dev/CCISS/c0d0p2 4.9 G 1.6 G 3.1 G 34% / esx3-installation
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / esx3-installation/boot
  / dev/CCISS/c0d0p7 2.0 G 101 M 1.8 G 6% / esx3-installation/var/log

  Cannot continue installation due to the lack of space and don't have the option upgrade CD directly (of complicated issues)

  Do you have any suggestions?

  Thank you

  It sounds like this host has already been improved 3.x! In this case you will not be able to upgrade to 5.x using the Manager to update because of the small partition/boot (99 MB).

  to remedy the hosts against a basic upgrade

  ... You cannot use Update Manager to upgrade to 5.0 ESXi host, if the host has upgraded ESX 3.x to ESX 4.x. These hosts have not enough free space in the partition/Boot to support the process of update Update Manager. Use either interactive or scripted upgrade.

  André

• Host does not support configuring passthrough (DirectPath i/o)

  Hello

  I just installed ESXi 5.0 on a Fujitsu CELSIUS W350. http://support.TS.Fujitsu.com/UKFAQ/ProfessionalPC/Celsius/W3xx/W350.htm

  CPU: Intel Core 2 E6300 http://ark.intel.com/products/27248/Intel-Core2-Duo-Processor-E6300-(2M-Cache-1_86-GHz-1066-MHz-FSB)

  The CPU must be compatible with Intel Virtualization Technology (VT - x)

  As far as I can see that the "Intel Virtualization Technology" is also enabled in the BIOS, but I still just get the message "Host does not support configuring passthrough" under "Configuration-> advanced settings.

  I would like to have access to certain PCI cards in guest. Any ideas how to make this work? USB transfer works very well...

  Thank you!

  Welcome to the community,

  What to look for support DirectPath is ' Intel® Virtualization Technology for Directed i/o (VT-d).

  André

• ESXi 4.1 - Dell Poweredge 2850 - tape backup - host does not support configuring passthrough

  I'm trying to get a tape backup to work on my ESXi host, so I can save my win2003 VM.  I get this error under VMDirectPath, 'host does not support configuring passthrough ".  Under Configuration > storage adapters > I don't see my tape drive listed.  Also, I noticed that my SCSI controller card is NOT on the HCL (Adaptec 39160).  See.  This is probably why passthrough doesn't work.

  So, I was thinking of buying this one (Adaptec 39320) because he seems to be on the list.  This will solve my problem or is this server too old for passthrough to work?

  To use VMDirectpath on an Intel Server chipset used must support Intel VT - d (Directed i/o).   I don't think that's the case with the models of 2850, but if it was you would see an option in the BIOS to enable this.  It is a separate option of VT - x, which allows the host run the 64-bit clients.

• This host does not support VT *.

  I get the message: "this virtual computer is configured for.

  64-bit operating systems. However, 64-bit operation is not

  possible.  This host does not support VT continue with 64-bit support"?

  If I don't answer him then continues to try to start the virtual machine but cancel then with "the task was canceled by a user" even if I don't cancel anything. If Yes, well, after validation, and attempt to start the ISO XP it says "this processor is not compatible with x 64 mode. Please install a X 86 32-bit operating system. »

  That's what I get every time I turn on a virtual machine where I'm trying to start a 64-bit XP ISO file so that I can install XP 64 bit on it.

  I am running 4.1 on a 64-bit VM ESX (Redhat Linux 5 64-bit) of VMWare Workstation v7.  I tried Windows XP 64-bit and other flavors of

  Linux 64-bit but same problem with all of them.

  My physical pc consists of: CPU Q6600 (which supports VT).  The mobo is P5E - VM HDMI and VanderPool (VT) with XD bit set is enabled in the BIOS.  It is running

  to 3.60 GHz.

  So I can't install any 64 bit OS because it tells me that my pc ESX 4.1 VM does not support VT... I started in its virtual bios but there is no parameter VT it.  Yet, when I boot ESX with the preferred Mode of CPU Intel VT-x/EPT or AMD-V/IVR value I get a message bit on the right down saying: "this host does not support the EFA. For material aid to virtualization with MMU software. "So I don't know that he sees VT during startup of ESX, only virtual computers created in ESX do not seem to see it.

  I have already added the following in my vm ESX 4.1 .vmx file:

  guestOS = "vmkernel".

  monitor_control.vt32 = 'true '.

  monitor_control.restrict_backdoor = 'true '.

  I tried also to add the above in vmx file XP 64 bit VM as well.  Any ideas on how I can install a 64 bit OS in a virtualized 4.1 ESX? Or it is not possible?

  yorkman.

  you run nested ESX. In ESX ESX. You can install 32-bit operating systems in this type of environment. VMware has no VT support for nested VMS

• The destination does not support 64-bit clients

  My VMware server contains two Quad Core 64-bit processors.  I'm migrating a physical machine running Windows 2 k 3 64-bit to a virtual machine, but the migration/converter of VMware software responds with, ' < span class = "objects" > the destination does not support 64-bit clients.» Why doesn't it let me convert the machine?  Thanks for any help.

  You must enable VT in the advanced options of the BIOS of the HOST servers.  Once this is done, you must turn off the physical machine and power then turn it back on.

• iPhone 6 showing the accessory is not supported

  I have an iPhone 6 when I try to load it says that the accessory is not supported and I use the original cable Apple. I can not load unless I turn the iPhone to let in charge. I need someone help me to solve this

  Hello ibrahimfromregina,

  Thank you for using communities of Apple Support.

  I see that you get an error that the accessory is not supported load when you try to load your iPhone.  To help get this problem solved, I suggest that you run through the troubleshooting steps below.

  If an alert says that your accessory is not taken care of or certified

  These alerts can appear for several reasons: your iOS device could have a port of loading dirty or damaged, your loading accessory is defective, damaged or not certified by Apple or your USB charger is not designed to load devices.

  Follow these steps:

  1. Remove all debris from the charge on the bottom of your appliance socket.
  2. Restart your iOS device.
  3. Try another USB cable or charger.
  4. Make sure you have the latest version of iOS.
  5. Contact Apple to set up the servicesupport.

  Recharge your iPhone, iPad and iPod touch

  See you soon.

• ProBook 6440 b: cannot upgrade to Windows 10 - "The CPU is not supported" error message

  Hello everyone

  I have a HP ProBook 6440 b. CPU is intel core i7 M640. It is currently running Windows 7 64-bit edition. I'm trying to update to 10 Windows using Windows 10 Upgrade Wizard and it gives me error. It says "Windows 10 does not work on this PC. The CPU is not supported (NX). »

  Any help will be appreciated. Thanks in advance.

  Hello:

  I suggest that install you the upgrade from the DVD (authoring tool of your own from the link below - media Make).

  https://www.Microsoft.com/en-us/software-download/Windows10

  The DVD will bypass the hardware checks.

  Also, when you install W10 from the disk, skip verification of updates when you are prompted.

• 5132: "the format of the string is not supported.

  Hello

  I'm listening channels of my new USB-5132 on the disk at the same time, using the c# example "scope: live stream To Disk.  I entered "0:1" (without the quotes) in the channel name box.  The result is the error "the format of the string is not supported.  Is there another syntax or example that will allow me to broadcast two channels of 5132 on disk?

  Thank you

  Penny

  Hi Penny,

  Channel string syntax

  If you try an empty string or a string separated by commas (as in "0.1") do you still see this error?

  What version of NOR-SCOPE do you use?  You can find it in Measure & Automation Explorer under software.

  Also, I would be interested to know if you have other devices (besides the 5132) which show the same behavior.

  -Andrew