The installation phase

Similar Questions

• 7520 new stuck in the installation phase. Print head move load ink cartridges

  I'm stuck in the new phase of printer configuration. After running through the commissioning of questions and I opened the cover to charge the ink cartridges and the print head did not move. I ran across several reset process... Unplug the printer. Wait 60 seconds and plug it in again. Browse the configuration... Unplug the printer... more.

  This printer does not seem to be any cartriages.

  Hey JohnTT,

  Sometimes, these printers come with packaging that holds the printhead completely to the right at the gas station.  This avoids damage to the product during shipping.  You see all plastic parts orange that it may contain in place or Blue Ribbon?

  So, have you tried the carriage to the right hand?  Can it be moved or is it blocked?

  If the printer still will not release the print carriage after the power cycles and move it by hand, then I suggest you return the product and return to the retailer of purchase or by calling the HP Technical Support to see about a replacement.  The phone number for the USA / Canada residents is 1-800-474-6836.  If you are not in this region, click here.

  I hope this helps.

• Replace a hard drive in dv6 but is not completed the installation phase

  I replaced my hard drive with a disks recommended by an expert from HP in this forum, and he seemed fine. After starting with my #1 recovery and loading of each disk when you are prompted, I got the final guest/message: "preparation of the recovery is complete. Remove the system recovery media. Once the computer is restarted, the installation of recovery process will begin... Support on continue restart the computer. "When I hit the"Continue"button, the screen went black as if it has been restarted. But instead, a black screen with the HP logo in the centre appeared, with the text: "Press ESC for Boot Menu" in white letters in the lower left corner. Waited about half an hour, and then you press the ESC key, but it changed nothing. Same screen HP. And that's all - nothing else has happened. I left it on all night, thinking perhaps that it takes time to get there, but in the morning, the same screen was there and my phone was hot as if in use. So I turned it off right there. What would not, and that I should try now?

  Turns out that I don't need to download the Microsoft Windows software and then struggle to find the right drivers, thank God. My recovery discs works perfectly after all.

  Having read tons and tons of forum posts about this problem, I finally found a solution that worked really - posted by another user, GoodTimes81 (thanks!). This solution is pasted below (with numbers and an additional note added by me):

  (1) put the recovery disk #1 in and

  (2) when the Recovery Manager screen loads, you will get a few options, but the one you want is the command prompt (which appears after you select "Run a computer check.")

  (3) in the command prompt, I typed bootrec.exe/fixmbr, you press on enter and waited it says the operation completed successfully.

  (4) I typed bootrec/fixboot and then you press on enter and again waited until he said the operation has completed successfully.

  (5) after having done that I left the command line, restarted my computer and waited until my recovery disk #1 loaded up again.

  (6) then, I chose the recovery system to the Recovery Manager screen and went through the process of insertion of disks 1 to 4.  When the 4th disc is complete, it says remove the recovery disc and press on continue, which I did, then it restarts, except that this time it restarted and actually started the installation and facilities it is supposed to do and has completed the recovery process.
  _________

  The other user said these steps solved the problem for her, and they could work for you. Finally, they worked for me, except after step 5, the recovery disk #1 would not load again. I received an error message (the black screen, white letters) mentioning a problem of location startup (sorry, that I did not write down exactly what he says). I pressed the button power to restart, but got the same error message.

  So I pressed the button to power again but this time, you press F11 repeatedly until I had a menu of options. The option to boot was F9, then I pressed F9 and selected "CD/DVD player" (which I had already done elsewhere earlier in the process, but maybe it had reset after entering the command request?) and then restarted again.

  This time, it worked, and I was back in step 6 above. Load the discs one at a time (note: I have 7 discs instead of the 4 mentioned by another user), and after that the disc was done and I got the prompt to "Press continued to restart", it restarted and he proceeded to load all the software, drivers, etc as it is supposed to. Yay!

• Install Windows 8 on external drive Thunderbolt - Windows could not prepare the computer to begin the next phase of installation

  Hi all

  I'm at my wit's end trying to install windows 8. Let me start at the beginning: I used to have windows running on my Mac Pro ssd internal 8.1, installed via bootcamp. It worked well for a while, and then refused to start, gives me a blue screen KERNEL_SECURITY_CHECK_FAILURE. Despite some advice from lonely T, I was unable to fix and ended up wiping the partition and relocation, again via bootcamp. Yet once again, it worked for a few months, then the same problem. I made this one last time, and it only lasted 2 days... So I gave bootcamp.

  I think that the hybrid MBR partition scheme that implements bootcamp is the culprit, but I don't really have evidence to substantiate this claim. In any case, I tried to install windows in EFI mode. (If I understand correctly, the hybrid MBR is set up to allow windows to install in legacy BIOS mode, but that windows 8 may now install efi, which supports my Mac Pro mode.) My Mac is the new Mac Pro (end of 2013, trash in shape), and I can say short UEFI 2.0 (I have the latest efi update from apple installed).

  The method I'm trying:

  1. create a new partition in HFS + on my external drive using disk utility. The drive has now it's efi partition and partition empty 750Go I want to install windows a 1.25 TB storage partition that I use with my mac. It has a GPT. I formatted HFS + and no FAT, because I think that disk utility creates the same hybrid-MBR as training camp every time a FAT partition is created.

  2. use gdisk to confirm that the disc does not have a hybrid-MBR. (sudo/dev/disk1 gdisk watch MBR: protection)

  3 restart my mac and hold the possibility to put in place to bring up the boot efi menu.

  4. Select the EFI_Boot DVD icon (that's the windows 8 install dvd that I have in my superdrive USB drive)

  5. go in the menus of the disk selection screen installation and delete the partition in HFS +, I created to install windows on (the format option is not available)

  6. now select "Unallocated space" on the good drive and click Next.

  The problem:

  Partitioning seems to go ok (there is no feedback on this basis, but it proceeds to the next screen, and all new partitions expected are there if I check diskutil list later). He said it is "copy of windows files", but then stops with the error "Windows has no prepare the computer to start the next phase of the installation." To install Windows, restart the installation. "If I restart, I can start the same process all over again and get the same result.

  The Question:

  How I get this error and get windows install?

  Extra pieces:

  • The first time it happened I assumed it was the new sip / thing "without roots" in El Capitan, causing problems, then I disabled, but I still get the same error.
  • After reviewing the diskutil list output after one of installs it without success, I found that a labeled EFI partition has been created after my storage partition (the original efi partition was still there in the upper part of the disc).
  • I have windows 8.1 installed now bootcamp on my internal ssd. It was planned to use it and winToUSB to put windows on my crush, but I found that it only works with usb2. I do not have installed could cause problems with the installation on another disk.
  • Before say you I can't run windows on an external, yes you can, and many people have. I read windows sees thunderbolt internal disks.
  • I read a few other posts on this and other sites on this problem, but could not find a pertitnant solution to my situation. I found one that suggested to remove the efi on my disk partition, but that seemed like a bad idea, so I didn't try.
  • I write this at 1 in the morning after a day spent in front of the computer trying to get this working, so please excuse typos typing or other. I am pleased to provide you with any pertinant information helping you will help me.
  • Thank you!

  The other thing I tried also almost succeeded:

  Although I prefer to get the method above works, because it seems the most promising, is something else, I've tried that I thought worth mentioning. If you offer advice pertaining to this method rather than the above, I would appreciate it if you could explicitly declare that at the top of your answer. Thank you.
  

  I tried to install windows on the physical disk using vmware and virtual box. The instrutctions I followed for this can be found here: http://www.andrewsavory.com/blog/2011/2156 (the only thing different, it's because it's on an external drive, I created the Fat 32 partition manually using disk utility). The first time (using vmware) installation seems to go off without a hitch, but I couldn't get my computer to see the windows partition as bootable with the boot efi menu hold-option regular refined or with system preferences-> startup disk. I think that I was using always inadvertently a hybrid-MBR at this stage. I tried to repeat this new beginning with the first two steps above to avoid the hybrid-MBR. But now when I try to create the virtual machine based on the gross vmdk, it starts to copy the files then says not sufficient permissions and fails. I don't know if it's a permission with the disk or the hard problem. I tried chmod 777 and chown $USER of the vmdk disk (/ dev/disk1s3) does not.

  Wow, that was a long post...

  1. when a second drive is detected by the Windows Setup program, he wants to create his own brand of EFI (104 MB) and not to mess with the Mac EFI (200 MB). You can force it to use the EFI to the Mac using Diskpart commands.

  2 instead of HFS/FAT32, create a piece of 750 GB free space and it should only get a new MSR/MSD, without the part of EFI.

  3. on your VM method, the link you have is quite old. You have a MP 2013, with references to the 2010 Mac alumni and is a bit too archaic to be useful. http://forums.macrumors.com/threads/install-a-Windows-7-partition-on-Mac-OSX-Wit hout-optical-car-or - usb.1836959 / #post... seems to work for many and can be useful for a test. It also uses Winclone.

  4. you can also try http://bleeptobleep.blogspot.com/2013/02/mac-install-windows-7-or-8-on-external. html .

• tried to install a new copy of Windows XP Home. Everything is OK until the final phase, when the "blue-screen" appeared during the installation of the drivers.

  Installation of xp and blue screen of death

  Hello

  I recently formatted the partition boot and recovery of a laptop Medion2230, then merged the two partitions in a single NTFS partition.  Don't ask why, it's a long story.

  Then, tried to install a new copy of Windows XP Home.  Everything is OK until the final phase, when the "Blue Screen of death" appeared during the installation of the drivers. Restarted and installing XP as normal to repeat the first onboard staged and went to the "blue screen" at the same point as before.

  Using some diagnostic software, I reformatted the drive again, loaded XP set up and I had the same problem.

  Someone knows what to do?

  Thank you allionii123

  Now solved and pc with Windows XP home.

  Discovered a trick online, who said that at the beginning of XP installation, press F5, and this leads to a screen option - select 'standard pc' and continue with the installation of XP.

  (Again), formatted hard drive ran XP installation and followed above point.

  Worked the first time.

  Thank you very much for your advice.

  I think you can pressing F5 or F7...

  How to impose a layer of HAL during an upgrade or an installation of Windows XP

  Impose a HAL

  To prevent Windows XP to automatically determine the system HAL during the upgrade or installation of Windows XP, you can manually force in a system HAL. To impose an Abstraction Layer HAL during a upgrade or installation of Windows XP, follow these steps:

  1. During the phase in text mode of Setup, when you receive the message at the bottom of the screen, press F5:
     Press F6 if you need to install a third-party RAID or SCSI driver.

     Note If you press F7, the Standard PC HAL loads and the ACPI enforcement is bypassed.

  I would not need this except in the systems of many older and low end... :-(  After all, in the same article, for Standard PC they say: "the CPU can be a 386, 486, Pentium, Pentium II, or Pentium III '...

  Thanks for letting us know what you were doing.  Do you have all the necessary drivers after loading Windows XP?  I would not recommend using the default drivers for any hardware - always see what the manufacturer offers on their web page for each component of your system - card motherboard chipset, audio, video, network devices, etc.

• Windows didn't prepare the computer to start the next phase of installation

  Hey I get the error "windows has no prepare the computer to start the next phase of installation" during the installation of vista and Windows 7, I use xp professional I would like to mention that a few days ago, I company vista works well, so I thought I should update to the win 7 but since that day I have my receive this error message and also I could not install vista  , the specifications of the system are: optima PC with motherboard 2.8 GHz intel and intel 865GLC inside the processor 2.8 GHz, 1 GB ram, 160 GB HDD
  PLEASE please help me I lost so much time, but all in vain :(: @.
  I also tried msconfig utility chkdsk, but she shows that its fine and also unplugged all other additional devices in the connection only the mouse and keybard but no American (e):
  PLEASE SOMEONE HELP ME

  Hello

  These are forums for vista for home pc users

  you use enterprise

  Try the vista it pro forums

  http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro/

• Cannot install Windows 7 "Windows didn't prepare the computer to start the next phase of the installation." to install Windows, restart the application.

  Original title: Installation of Windows 7.

  I tried to install Windows 7 (clean install from XP and reveived the following message is displayed:)

  Windows didn't prepare the computer to start the next phase of the installation.  to install Windows, restart the application.

  I restarted my PC, anti anti-virus disabled (as advised) and still get the error message.

  According to the Upgrade Advisor Windows 7 my PC is compatible.

  Any ideas?

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  Boot from the Windows 7 DVD
  Click Install now
  Accept the license agreement
  When the option is displayed to select a type of installation, click (Custom advanced)

  Select the disk partition where you want to install Windows 7 click Next.

  You will receive the following warning:

  The partition you have selected may contain files from a previous Installation of Windows. If so, these files and folders will be moved to a folder named Windows.old. You will be able to access the information in Windows.old, but you will be able to use your previous version of Windows.

  (At all costs, do NOT click on anything in Format, deletion or Partition name.) So even do a custom installation, your personal files are still kept. Click OK

  The installation program will now begin installation. During installation, your computer will be restarted several times.

  Once the installation is complete, you can complete the Out of Box experience as the choice of your laptop, create a username, password, your time zone. You can then proceed to download the latest updates for Windows and reinstall your applications and drivers.

  You can then retrieve your personal files from the Windows.old folder and reinstall all of your applications and drivers.

  http://notebooks.com/2010/11/09/how-to-recover-documents-music-and-email-after-upgrading-with-the-Windows-old-folder/

• Download "Windows didn't prepare the computer to start the next phase of the installation during installation of Windows7.

  When installing windows7 in the second phase, it gives error such as ' Windows has not to prepare the computer to start in the next phase of installation.to install Windows, restart the installation. " It comes at the end of 50% of the extraction of windows.

  How you attempt installation?

  You are upgrading from a previous version of Windows?

  Are there devices non-essential attached to the system as a external hard drive or USB key?

  If so, try to disconnect them, they might interfere with installation.

  Could you give your full system specs?

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  1 disable any security software before attempting to upgrade

  2. make sure that your computer is updated (devices and applications)

  3. disconnect all external devices before installing.

  4. check your hard disk for errors:

  Click Start

  Type: CMD, according to the results, right-click CMD

  Click on "Run as Administrator"

  At the command prompt, type: chkdsk /f /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  1. click on start, type msconfig in the search box and press ENTER.

  User account control permission

  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  2. in the general tab, click Selective startup.

  3. under Selective startup, clear the check box load startup items.

  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.

  5. click on OK.

  6. When you are prompted, click on restart.

  7. after the computer starts, check if the problem is resolved.

  Also run the Windows 7 Upgrade Advisor:

  http://www.Microsoft.com/Windows/Windows-7/Upgrade-Advisor.aspx

• No visible hard drive during the installation of Windows 8 during the transmission phase of gathering primary.

  Hello

  I recently bought an Alienware m18X R2, and I wanted to install windows 8 (new installation) on this subject. I go through the ordinary procedure and boot from disk or during the time to choose the main drive for the installation. None of the drives are visible (error. no driver drive drive-impossible to find discs), this is the same error that occurred when I resorted to a regular update. Kindly advice. I have 2 drive HARD 500 GB in RAID 0, and a 64 GB SSD to set caching.

  Rémy

  What you need is the driver of TSRI Intel (see below).

  downloadcenter.intel.com/Detail_Desc.aspx

• installation of the elements 10, suspended from the final phase of the instalation

  I try to install 10 items, I brought, after my laptop PC (vista), and he gets what appears to be the long way through the instalation process then crashes.  I had to uninstall it it twice and try again, but it hangs at the same point.  Someone at - it suggestions?

  HI Manish

  Thank you very much for your response to the fourth attempt to install finally worked.  He was suspended at the end of the installation when it says delete backup files.

  Thanks again

  Adam

• I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  I am trying to install windows xp from the disk, but it hangs during the installation process. no error code. It just hangs. What is the cause and what is the solution?

  Hello

  1. at what stage of the installation, the computer crashes?

  2. what operating system was installed on your computer prior to this?

  If you have the similar problem as mentioned in these links, you can follow these links and check if the problem persists:

  Windows XP Setup stops responding (hangs) during the "Preparing Installation" phase

  Windows XP does not meet the Message "Setup starts Windows XP"

  Hope the helps of information.

• migrate from Windows 10 failure error oxc ox400d 1900 failed in the second phase of startup with the error during operation of data on my windows desktop 7

  Windows 10 has failed 75% error oxc 1900-ox 400 d has failed in the second phase of startup with the error during the operation of the Migrate_data on my windows desktop 7 using media creation tool. Help please.

  Turn off the computer.

  Wait 10 minutes.

  Start the computer.

  The installation program automatically restores your previous version of Windows 10 or an earlier version of Windows.

  Launch the prompt with administrator privileges.

  Press the Windows key + X

  Click prompt (Admin)

  Type the following command:

  Rundll32.exe pnpclean.dll, RunDLL_PnpClean /DRIVERS /MAXCLEAN

  Press enter on your keyboard

  Exit command prompt

  Restart

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times and try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Do a clean boot, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both and try the installation again.
  • If you update via Windows Update, when download reaches 100%, disconnect the Internet LAN (Ethernet) or wireless, and proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• Visual Studio 2010 Tools for the Installation of Office Runtime failure

  Hello

  the installation fails with the error code 1601. I studied this code but received no responses that could solve my problem. complete logs are pasted below. any help it will be appreciated.

  The following properties have been defined:
  Property: [AdminUser] = true {boolean}
  Property: [InstallMode] = {string} SameSite
  Property: [NTProductType] = 1 {int}
  Property: [ProcessorArchitecture] = {string} AMD64
  Property: [VersionNT] = 6.1.1 {version}
  Controls running for package "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)", phase BuildList
  Reading 'Version' of the 'HKLM\SOFTWARE\Microsoft\VSTO Runtime Setup\v4' registry key value
  Read the string value "10.0.40820".
  "Definition of value ' 10.0.40820 {string}" property "VSTORuntimeVersionOfficeInstalled".
  Reading 'Version' of the 'HKLM\SOFTWARE\Microsoft\VSTO Runtime Setup\v4R' registry key value
  Failed to read the registry value
  Do not set value for the property "VSTORuntimeVersionInstalled".
  The following properties have been set for the package "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)":
  Property: [VSTORuntimeVersionOfficeInstalled] = 10.0.40820 {string}
  Execution of the command controls 'VSTOR401\vstor_redist.exe '.
  Jump ByPassIf because the 'VSTORuntimeVersionInstalled' property has not been set.
  Result of operation operator 'VersionGreaterThanOrEqualTo' property 'VSTORuntimeVersionOfficeInstalled' and the value ' 10.0.60724': false
  Result of operation operator "ValueEqualTo" property "AdminUser" and the "false" value: false
  Result of the 'VSTOR401\vstor_redist.exe' command controls is 'Install '.
  "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)" RunCheck result: installation required
  EULA for components "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)" has been accepted.
  Copying files to the temporary directory 'C:\Users\rchand02\AppData\Local\Temp\VSD6BD2.tmp\ '.
  Copy "C:\Users\rchand02\Downloads\UnifyOffice_x86\VSTOR401\vstor_redist.exe" to "C:\Users\rchand02\AppData\Local\Temp\VSD6BD2.tmp\VSTOR401\vstor_redist.exe".
  Check the integrity of files C:\Users\rchand02\AppData\Local\Temp\VSD6BD2.tmp\VSTOR401\vstor_redist.exe
  WinVerifyTrust returned 0
  Trust file
  Controls running for package "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)", phase BeforePackage
  Reading 'Version' of the 'HKLM\SOFTWARE\Microsoft\VSTO Runtime Setup\v4' registry key value
  Read the string value "10.0.40820".
  "Definition of value ' 10.0.40820 {string}" property "VSTORuntimeVersionOfficeInstalled".
  Reading 'Version' of the 'HKLM\SOFTWARE\Microsoft\VSTO Runtime Setup\v4R' registry key value
  Failed to read the registry value
  Do not set value for the property "VSTORuntimeVersionInstalled".
  The following properties have been set for the package "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)":
  Property: [VSTORuntimeVersionOfficeInstalled] = 10.0.40820 {string}
  Execution of the command controls 'VSTOR401\vstor_redist.exe '.
  Jump ByPassIf because the 'VSTORuntimeVersionInstalled' property has not been set.
  Result of operation operator 'VersionGreaterThanOrEqualTo' property 'VSTORuntimeVersionOfficeInstalled' and the value ' 10.0.60724': false
  Result of operation operator "ValueEqualTo" property "AdminUser" and the "false" value: false
  Result of the 'VSTOR401\vstor_redist.exe' command controls is 'Install '.
  "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)" RunCheck result: installation required
  Check the integrity of files C:\Users\rchand02\AppData\Local\Temp\VSD6BD2.tmp\VSTOR401\vstor_redist.exe
  WinVerifyTrust returned 0
  Trust file
  Installation using the command "C:\Users\rchand02\AppData\Local\Temp\VSD6BD2.tmp\VSTOR401\vstor_redist.exe" and «/q /norestart» parameters
  Process came out with code 1601
  Status of the package "Microsoft Visual Studio 2010 Tools for Office Runtime (x 86 and x 64)" after the installation is "InstallFailed".

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• Installation of the Runtime Java - always message that failure of the installation, the wizard was interrupted.

  Cannot download - low loading of the Runtime is interrupted in the final phase of the Java Runtime low load, always fails - several days - several times, even interrupted the installation message - no installation. I keep without running the application, wall of fire mode, but nothing doesn't work - why the final installation is interrupted all the time, the same message that failed every time, how can I solve this problem – any help

  Hi Arvind,

   
  1. don't you make changes to the computer before the show?
  2. the problem occurs during the installation of other programs and applications?
   
  I suggest for the link and follow the steps in the article:
  Error: The wizard was interrupted before Java (TM) 6 update could be completely installed.

  http://Java.com/en/download/help/wizard_interrupt.XML

   

  If the problem persists, please contact Java support for assistance:

  Reference:

  http://www.Java.com/en/download/support.jsp

   

  Thank you.

• The screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. What should do?

  I installed upgrading W7 W8. Already during the final phase of installation, the screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. I tried the settings of brightness through the hardware buttons and in energy savings, but it remained the same. What should do? Karl

  Looking for a display updated sony driver.   Its always a good idea to do so during the updating of the OSs.