The keyboard does not work after installing Language Pack.

Similar Questions

• Equium M50-235: the keyboard does not work after upgrde memory

  I just did an upgrade memory on my laptop using the second slot located under the keyboard.
  However, as I was putting the keyboard at the rear, the ribbon cable has pulled away from the motherboard and even if I pushed
  Reconnect and fixed with the clip, the keyboard no longer works.

  Is there a service manual I can get hold of someone know what could be the cause of the problem?

  Thank you!

  Hello

  First of all, once you unscrew the keyboard, open the clip that secures it in place and reinstall the keyboard by ensuring that it is completely down. After that, now the flat cable in place, close the clip. Then, make sure that it is not lost and that it is seated correctly. Then turn on the laptop and see if it works. If this is not the case, try an external keyboard. If an external keyboard does not work, the keyboard on your MB controller is dead and you need a new MB. If an external keyboard works then your keyboard is dead, or the connector on the MB is dead. Best way to test is to try the first solution. If it doesn't work, take it to an ASP so they can try another keyboard for your laptop. Good luck.

• Keyboard does not work after installing Vista

  I loaded window vista and since my keyboard does not work, tried unistalling with no luck. who can help?

  Hi funminey,

  Please see the following article some troubleshooting on your question:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• His Dell Inspiron 1420, microphone and camera integrated into the laptop does not work after installing Windows 7 Professional

  No sound from my Dell Inspiron 1420 and the microphone and built-in laptop camera do not work after installing Windows 7 Professional 64-bit. My laptop has Windows 7 Vista 32 - bit family premium. My laptop is 64-bit capable and after going through the Upgrade Advisor, I installed Windows 7 64-bit. I can hear sounds when I use a headset plugged into the line-in Jack, but not through the speakers built into the laptop. I already tried new drivers from the Dell website, but I could not find.

  Any help will be much appreciated. Thank you.

  As it is has no drivers 64 bit Windows 7 on Dell Web site, your best chance is to install the 64-bit versions of Vista (if they exist) in compatibility mode, viz:

  Right click on the Vista driver, then select Properties > Compatibility tab. Now choose to run the program in Vista compatibility mode and then apply > OK. Right click on the file and select run as administrator to install it.

• Satellite A300D-126 the keyboard does not work

  I reinstalled the driver but it still does not. What could be the problem? Help please. Thank you

  Hello

  What s wrong exactly?
  You have reinstalled the drivers?
  What drivers do you mean?

  The keyboard driver is part of the Windows operating system and it cannot be reinstalled separately.

  If your keyboard doesn't work properly then either the software doesn't run as it should, or the material (keyboard) is defective.

  You could try reinstalling the operating system using the Toshiba HDD recovery to check whether the problem is related to the software.
  If the keyboard does not work after this procedure, then a hardware problem might be possible.

• Keyboard does not work after authentication on the RDS Session host

  When you connect to the RDS through the access portal or app keyboard does not work after authentication on the RDS session host. Offline authentication works very well, past will guide you to the RDS host, then when you try to reset your password, the keyboard does not work.

  Has anyone else had that... ?

  Options (some better than others!) are:

  1. move all MS applications seamless

  2. have an application named "Reset your password" (or similar) which uses MS Seamless.then you can leave other applications, as they are

  3 disable authentication carried forward and implemented our service reset password instead so people reset their password before can connect you.

  4. use the full desktop instead of transparent

• Safari does not work after installing macOS Sierra

  Safari and apple store does not work after installing macOS Sierra

  Alas, my crystal ball is in the shop for cleaning, so you will need to provide more details on what "doesn't work" and above all error messages. First of all, let's start the App Store. Provide as much information as possible for those of us who do not sit on your shoulder.

• Bitmoji keyboard does not work after last update iOS 10

  My Bitmoji keyboard does not work after that I updated to iOS 10 update. I have no idea why, my friends Bitmoji keyboard works fine after that she has updated her phone and mine does not work so I was wondering why. It worked perfectly fine before I upgraded my phone. I was wondering what to do.

  the same problem. He repeats to me go to keyboard settings and make sure that it says allows full access to Bitmoji and it does. Should not have upgraded to iOS.

• using firefox 24, yahoo toolbar disappears and the keyboard does not work on some websites

  We have installed firefox 24, yahoo toolbar sometimes disappears. On some web site when trying to enter a password, the keyboard does not work until you double click of the mouse on the registration form. This on two different systems of windows 7. Each thin seemed to work fine before the update prior to the installation of 24.

  Hello

  Try Firefox Safe mode to see if the problem goes away. Safe mode is a troubleshooting mode, which disables most of the modules.

  (If you use it, switch to the default theme).

  • Under Windows, you can open Firefox 4.0 + in Safe Mode holding the key SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac, you can open Firefox 4.0 + in Safe Mode holding the key option key when starting Firefox.
  • Under Linux, you can open Firefox 4.0 + with leaving Firefox then go to your Terminal and running Safe Mode: firefox-safe-mode (you may need to specify the installation path of Firefox for example/usr/lib/firefox)
  • Or open the Help menu and click on the restart with the disabled... modules menu item while Firefox is running.

  

  Once you get the pop-up, simply select "" boot mode safe. "

  

  If the issue is not present in Firefox Safe Mode, your problem is probably caused by an extension, and you need to understand that one. To do this, please follow article Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems .

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. It might help others who have the same problem.

  I hope this helps!

  Curtis

• My safari does not work after installing iOS 9.3

  My safari does not work after installing iOS 9.3

  This is a known issues with 9.3 and Safari (with the mail application and other applications)

  Some have reported success goes in the settings, safari, advanced and Disabling Javascript. Others said that Opera browser works, so you can use it as a workaround until a patch is issued. There is no indication how long can take this difficulty. Maybe in a few hours, could be days.

  or you just have to wait it out.

• Key on the keyboard does not work in firefox box when you type in the web site, but it works everywhere else?

  Key on the keyboard does not work in firefox box when you type in the web site, but it works everywhere else?

  Try Firefox SafeMode to see how it works there.
  
  A way of solving problems, which disables most of the modules.
  
  (If you use it, switch to the default theme).

  • You can open the mode without failure of Firefox 4.0 + by pressing the SHIFT key when you use the desktop Firefox or shortcut in the start menu.
  • Or use the Help menu option, click restart with the disabled... modules while Firefox is running.

  Do not choose anything at the moment, just use 'continue in safe mode.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before using the shortcut of Firefox (without the Shift key) to open it again.

  If it's good in Firefox Safe mode, your problem is probably caused by an extension, and you need to understand that one.
  
  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+themes

  Can be caused by an add-on to the AVG.

  When find you what is causing that, please let us know. It might help others who have this problem.

• Satellite W30T-A378 from - touch pad and the keyboard does not work

  I have a problem with my laptop, the touch pad and the keyboard does not work.
  Can someone help me what is the possible cause?

  Thanks in advance.

  Hello

  I guess you checked if the Tablet has been properly connected to the docking keyboard.

  Have you tried to unplug and plug the docking again?
  Note: there is a latch on the left you have to move and in order to remove the tablet.

  Perhaps there is a connection problem.

• keyboard does not work after sleep

  I have a light keyboard Logitech model Y-UY95. When the awakening of the mode standby the keyboard does not work.  Anything can be typed. I have to restart Windows 8 and then it works again.

  Had a similar problem on a HP Elitepad 900 go to sleep and not waking up... update the firmware/bios fixed it.  This known problem when I called HP, was not documented any wher however

• Keyboard backlit Y500 does not work after installing Windows 7

  Got a y500, love, installed Windows 7 (experience challenging, but glad I did now that it's done). Everything works like a charm, EXCEPT the backlight on the keyboard. By pressing FN + space does nothing. The keyboard does not blink when starting upwards, either.

  After repeated calls to the line of Lenovo, the responses I get are simply: we don't know why the keyboard backlight lights with Windows 7 installed.

  I don't want to go through the hassle to put Windows 8 on just for the backlight.

  There must be a way to activate the backlight of the keyboard while running windows 7. Lenovo, can you please go to the top of the chain of command to those who are working on updates of pilot and see if there is a way to make it work? Or tell me if I do something wrong?

  TL; Dr: keyboard backlight worked while Win 8 has been installed, put win 7 on, is no longer works.

  I would check the cable connections, the most likely problem.

  You can get a new keyboard on ebay for ~ $40... I'd rather spend than that being without my cell phone.

  http://www.eBay.com/ITM/400543129741?ssPageName=STRK:MEWAX:it & _trksid = p3984.m1423.l2649

  If the link does not work, you can search and Y500 keyboard, but others do not look right.

• Keyboard does not. Able to use for the connection does not work after that.

  The keyboard works to connect. But does not work after that.

  Hello Sml15,

  The embedded screen keyboard should still work even if the physical keyboard isn't.

  Try this first...

  Press and hold the Windows key and the space bar.

  If no joy, go to the search bar and with the built-in keyboard, type the filter keys and choose key filter on or off.

  In the window of the ease of access to the keyboard, disable FilterKeys.

  If all goes well, which will fix the problem.

  Let me know how it turns out.