The RPC server is unavalible

Similar Questions

• NLB - the RPC server is not available on the specified computer. To connect to the < Server >

  Have a Windows 2008 R2 SP1 NLB service two nodes on VMWare. Bothe nodes have two network cards. Internal one dedicated to NETWORK load balancing and the other for the network.

  Management console of NLB on a single poster NLB node is in good health. The two nodes are visible and OK.

  Management of NLB on the other node shows only its own node - while the other node is missing. An error when updating...
  "The RPC server is not available on the specified computer. "otherNode.com" connection error"

  I disabled the back loop check - it makes no difference.

  Any help please?

  I think I solved the problem...

  As I wrote previously, I disabled the back loop check in the registry on both nodes, create a new DWORD (32 bit) key...
  HKLM\SYSTEM\CurrentControlSet\Control\Lsa\DisableLoopbackCheck - with a value of 1

  Then, I made sure that the link speed & Duplex on all network interfaces are set to a specific value (no Autonegotiation), for example. 1000 Mbps Full Duplex (in my case).
  Ideally only the NIC - on each node - connected to the NETWORK load balancing must be configured with hard values.

  This solved the RPC error in my environment of NLB.

  Hope this helps those who have the same symptoms.

  Samuel.

• error code 1722: the RPC server is unavailable. (I can't print documents)

  Hello

  I can't print my documents, I have message from UN code error 1722 the RPC server is unavailable
  I started solving the problems on my printer, Windows did not find problem.
  I bought a software to repair Windows (Regenie), I was able to print during the morning, and the afternoon impossible.
  I restarted the Regenie software, I restarted my PC, and always impossible to print documents, with the same error error code 1722 the RPC server is unavailable
  I don't know what to do, thanks for your help
  Thanks for your replies
  Good to you

  Hello

  See this page to select your language:

  http://support.Microsoft.com/common/international.aspx

  ====================================

  Or sorry that it is area English.

  Left click at the bottom of the Microsoft Community page

  English and set your language.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I get an error message that says that the RPC server is unavailable when itry and open something

  I can't open my computer, Control Panel, my documents and devices everythings drivers comes with the rpc server is unavailalbe

  Hello

  1. have you made changes on the computer before this problem?

  2. what operating system is installed on the computer?

  The RPC server or remote procedure call is a service on your computer that allows other computers to access remotely.

  Method 1: You can check the event viewer for detailed information on the problem. Consult the following links.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Method 2: The Remote Procedure Call (RPC) Services service must be started and startup type must be set to automatic.

  (a) click Start, type services in the start search box and press enter.

  (b) in the Services window, find a remote procedure call and do a right click on it to select Properties.

  (c) under the general tab, make sure the Startup type is Automatic and the Service status indicates Started.

  Method 3: If the methods above help not, perform a restore of the system in safe mode.  You can restore the computer to a date when the computer was working properly.

  a. click Start, type System Restore in the search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  b. in the System Restore dialog box, click choose a different restore pointand then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  Reference: System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  See also: http://support.microsoft.com/kb/555839
  This article does not apply to Windows 7, however, you can see the steps.

  Let us know if it helps!

• Content file download failed. Reason: The RPC server is unavailable.

  Hello

  Please help, I have the following error with my WSUS. The clocks are so successful.

  According to the survey, it is said "updated the files needed: 2589 ' 'downloaded 0.0 MB of 30 years, MB 196,09.

  MT event logs show ID 364

  Content file download failed. Reason: The RPC server is unavailable. (Exception from HRESULT: 0x800706BA) Source file: /msdownload/update/v3-19990518/cabpool/windowsdesktopsearch-kb926356-v2-x86-nld_72b01991a8ebadf72d2512e19234943920ee4104.exe Destination file: c:\WSUS\WsusContent\04\72B01991A8EBADF72D2512E19234943920EE4104.exe

  I opened the firewall to allow full access to the net to the WSUS server, so it does not use a proxy.

  Please for any assistance you can offer.

  Did you run the Bits? Rob - bicycle - Mark Twain said it is good.

• Error "the RPC server is unavailable."

  I have a Windows XP Home SP3 PC who, since yesterday has been report error "the RPC server is unavailable" in attempting to perform specific tasks such as remove programs via the control panel and of the files of backup using Acronis 10. 'Paste' files which have been 'copying' ed by right click of the mouse or drag-and - drop, and finally, Internet Explorer 8 does not load authorize also Windows Explorer is no longer. I suspect that all these problems, which began at the same time, are connected!

  I did a virus check full system using AVG 8.5 and booted in safe mode "...". from last known working configuration"but nothing works.

  Any thoughts?

  I'll make sure that your Remote Procedure Call (RPC) server is running.  Right-click on my computer-> Manage and go to the services section.  You start and stop the services from here.  You can also right-click and select Properties... and see the service dependencies.

• When I try to renew my IP address I get the error: the rpc server is unavailable.

  I'm not getting Ip Add. in my laptop. When I try to renew the ip with IPCONFIG/renew it gives error the rpc server is unavailable. If I try to start this service in services.msc, that she does not get any changes.

  Thank you & best regards

  Aniket

  I would like to check the status of the Services.

  Click on the Start button and select Control Panel, administrative tools, Services. Locate the RPC end point Mapper in the list and make sure that the startup type is automatic. If it is not set to automatic, right-click and select Properties, general tab. There is a box after the startup type. The options are available in a menu drop-down by clicking on the down arrow to the right of the box. Make the change and click apply and then click OK. Restart the computer and verify if it has started.

  Hope this helps, Gerry Cornell

• After the removal of a virus, I can't connect to the internet, is looking for an IP address, and the RPC server is unavailable, said

  My netbook has a virus so I did a scan and remove infected files and a program which the virus attached itself to.  Now, I can not connect to the internet.  He is looking for an IP address, and he also says that the RPC server is unavailable.  Any ideas?  Help

  Hello

  Step 1: Start your computer in safe mode, and then try to start the Remote Procedure Call (RPC) services and start the computer in a clean boot
  a. Click Start, type services.msc and press to enter.
  b. in the list of services, double-click Remote Procedure Call services.
  c. change the startup type to automatic, and then click Start.
  d. click ok to apply the changes.

  Reference: http://windows.microsoft.com/en-US/windows7/what-is-safe-mode

• Error message: "unable to connect to the RPC Server" and no internet connection.

  Original title: recently installed a program of pc cleaner. Seemed to really speed up my laptop that is running Windows XP.

  After two days I try to connect to the internet and no connection lie. Uninstalled the pc cleaner without problem but the problem continues to exist. All tests, etc., result in "unable to connect to the RPC server. Slide short drive and reinstall XP, are there any other things to try?

  Hi Wantamustang,

  You can try the following steps and check.

  You can set the remote procedure (RPC) call Service to start automatically:

  a. clickStart, point to settings, clickControl Paneland then double-clickServices.

  b. in theservices list, click the remote procedure (RPC) call Serviceand then clickStartup.

  c. underStartup Type, click Automaticand then click OK.

  d. restart your computer.

  You can also consult the following article:

  Windows wireless and wired network connection problems

• My XP PC clock does not have to be updated; error report is: "the RPC server is unavailable."

  Hi there u clvr g33ks. Wu can help me slve ths prblm? My XP PC clock does not have to be updated; error report is: "the RPC server is unavailable"? I have tried pretty much everything hv what is allocated to me.

  Hello

  You can view these steps

  a. Click Start, type CMD. EXE and press ENTER.
  b. run the following commands one by one. (Press ENTER after typing each command.)

  NET STOP W32TIME

  W32tm /Register

  NET START W32TIME

• I got a message saying that the RPC server not available. I can't print or download the software for my printer.

  I got a message saying that the RPC server is unavailable.  My print spooler seems OK and my Dependencies tab it shows not itdepends on CPP, but I can't use my printer and I can't download the software because the driver is missing.  I can't download the driver for some reason any.  My printer is a lexmark X 1190.

  Hi donnasmum,

  1. When you receive the error message?

  2. did you of recent changes on the computer?

  3 when was the last time it was working fine?

  4. do you have security software installed on the computer?

  Method 1

  According to the Lexmark solution, you will need to restart the service on the computer print spooler.

  Error: "the RPC server is unavailable."

  Method 2

  If fails it to step above then check out the link below and run the fixit tool available.

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/en-us

• My computer has been recognizing not my two printers. He says that the printer spooler was not working. So I uninstalled my printer and when I tried to reinstall I received a message that the RPC server is unavailable.

  My computer has been recognizing not my two printers (which I have had for years).  The message says that the "spools of printer was not working" when I tried to print.  So I uninstalled my two printers and tried to re - install.
  Then I get a message that the "the RPC server is unavailable".

  Hello Sue Strong,.

  Thank you for your message.  Let's try the following:
  Click 'Start' > right click on 'My computer' > select 'manage '.

  Click the (+) sign next to "Services and Applications" > select 'Services '.

  On the right, find and right-click "RPC Remote Procedure Call ()" > select "Properties".

  Select the "Recovery" tab, then successively in first failure, second failure, etc. "restart the Service"

  Validate the change OK
  Stay in the services menu.
  On the right, find and click on "Print Spooler" > select "Properties".
  Click on the 'Start' button and check the "Startup type" is set to "Automatic" and click OK.
  If these steps resolve the problem, click HERE for more information and troubleshooting techniques.
  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to print error message...... "The RPC server is unavailable."

  Unable to print error message...... "The RPC server is unavailable."

  Run the HP Print & Scan Doctor program. (link)

• Application of automatic certificate for local system failed (0x800706ba) the RPC server is unavailable.

  I get these errors on some Windows 7 machine "registration of automatic certificate for local system failed (0x800706ba) the RPC server is unavailable" ID of the 6 event and event ID 13

  "Registration certificate for Local system failed to enroll for a certificate of computer with application ID N/A dc.contoso.com\contoso-DC-CA (the RPC server is unavailable." 0X800706BA (WIN32: 1722)). »

  other windows XP, Windows 8 and windows machine 7 receive the certificate through auto-enrollment.

  Hi Sam,

  Thanks for posting your query in the Microsoft Community Forums.

  Because the issue is limited to with RPC server, it is better suited for the IT Pro TechNet public. Please ask your question in the Forum on TechNet Support. You can follow the link to your question:
  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro/
  I hope it helps. If you have problems in the future, please let us know. We will be happy to help you.

• XNET - activation of the RPC Server - error

  Hello

  I am trying to load XNet database on my RT goal and now I get the error using the Xnet API. Running multiple remote database manager XNet vi doesn't help not either as it is still stuck with the error and no waiting period.

  I can connect to my goal of RT so this isn't a firewall problem and I can even speak using the NI-Xnet database default value, it's just that when I try to load my database on the remote control it gives me these errors

  I tried to go to MAX > tools > NI CAN > RT Configuration and I got this error as shown in Capture.PNG.

  I use cRIO 9067 and Xnet, I use NI9860 on my 8th slot.

  Has anyone encountered this problem, enable RPC server, how can I do? and is it possible to directly pass the file of database on the target of RT.

  Thank you

  Well, I have done what I wanted, except for the problem to be solved "RPC error not found" issue.

  I don't know, but in my case database deployment worked when I changed the password authentication, initially I had a configuration password for my RT goal, but when I removed the password empty, all the screws, Manager NI-XNET database example started working.

  I know, there was a suggestion in some links to enter ' [usernameassword]@IP address] "but it did not work for me, even in the database manager Xnet is mentioned anywhere that the IP address must be entered in this format, what they ask is the IP address in my case it did not work with IP address.

  In addition, one thing to note here is that, by default when you receive product OR there is no password protection, usually the password is empty, then most of the user would have never encountered this problem.

  So I would say the resolution as "Remove password of target RT.

  Thank you

  Lakhvir