Failed redundancy, RAID 1 drive missing

Similar Questions

• RAID controller driver missing

  Hi, I got an error message that wanted me a pilot RAID, but when I tried to install it says that I did not meet the minimum requirements? But it does not list memory etc, how do I do lol?

  Any help would be greatly appreciated. Thank you

  Hello

  I suggest you do of course drivers have been downloaded and installed correctly.

  Go to the Intel website, select the good motherboard, select windows vista and drivers, then raid. Copy to usb and follow the directions on the page.

  Hope this information is useful.

• Satellite A30 - ACPI driver missing

  Hello
  I have an old A30 that I just installed Win7 on. Everything is fine apart from a missing driver - unknown device ACPI

  In Device manager the hardware ID is ACPI\CMP0101

  Now this laptop fan lights not bad and she has a random problem to close without reason. I checked the fans and they are clear. In my view, that stops can be connected to this driver missing because it can control the temp/fans that stop it overheating, and then I could be wrong...

  I would appreciate any help and advice

  Thanks in advance

  mcdodd

  Hello

  Are you sure that you want to use Windows 7 on this computer laptop oldie? In my opinion, you should be happy with a preinstalled OS to Toshiba. There are all the drivers and tools pre-installed and you don t have the stress with the driver installation. You can have fun with your laptop :)

  As you can see in another thread, you must reinstall Windows to solve this problem:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=126340

• Pavilion 15-n201sk: driver missing

  computer hp laptop pavilion 15-n201sk windows 7 64-bit

  driver missing for:

  1 - Ethernet controller

  2 - Bluetooth controller

  3 Intel (r) 8 series xHCI HC - 9 c 31

  4. PCI device

  5 - video controller

  6 - unknown device

  Hello:

  You should be able to use the W7 x 64 drivers and the software of this model to yours except the BIOS and firmware files.

  http://support.HP.com/us-en/product/HP-Pavilion-15-N100-notebook-PC-series/5436989/model/6422011/drivers

• ProBook 6550 b: driver missing Base system device

  After you have reinstalled Windows 10 on a Probook 6550 b I can't find the correct driver for both devices.

  -Driver missing Base System Device 1:
  Device PCI VEN_1180 & DEV_E852 & SUBSYS_146D103C & REV_01\4 & 1089976f & 0 & 02E2 requires installation.

  -Lack of pilot system of Base 2 device:
  Device PCI VEN_1180 & DEV_E230 & SUBSYS_146D103C & REV_01\4 & 1089976f & 0 & 01E2 requires installation.

  Is it possible to put me in the right direction?
  
  Thank you very much.

  Lennard

  Hello

  Try to install the Windows 7 version of the Ricoh Media Card Reader Driver.

  Kind regards

  DP - K

• I have a 2560p which shows driver missing for 'Base system device '.

  I have a 2560p which shows driver missing for 'Base system device '. Shows the location

  PCI Slot 2 (bus PCI 35, device 0, function 0).

  What is the device and where can I find the driver? Thank you

  Excellent thanks a lot!

• ProBook 6640b: driver missing for 'Base system device' XP Pro on a Probook 6640 b

  Greetings-

  I get two error messages that read "Base system device" driver missing.  The hardware for the first is ID:

  PCI VEN_1180 & DEV_E230 & SUBSYS_1726103C & REV_01

  PCI VEN_1180 & DEV_E230 & SUBSYS_1726103C

  PCI VEN_1180 & DEV_E230 & CC_088000

  PCI VEN_1180 & DEV_E230 & CC_0880

  And the other is:

  PCI VEN_1180 & DEV_E852 & SUBSYS_1726103C & REV_01

  PCI VEN_1180 & DEV_E852 & SUBSYS_1726103C
  PCI VEN_1180 & DEV_E852 & CC_088000
  PCI VEN_1180 & DEV_E852 & CC_0880

  Any guidance would be appreciated!

  Thank you.

  Hello:

  You need this driver that will install two devices...

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4149986&swItemId=ob_79991_1&swEnvOid=1093

• Compaq presario v 3780TU: Base System Device Driver missing

  product compaq presario v 3780TU

  problem - the two driver missing basic systems, audio device does not not only integrated speakers work not, works of headphones

  problem when I upgraded to the Windows OS 10

  first base h/w device id is

  PCI VEN_1180 & DEV_0843 & SUBSYS_30CD103C & REV_12
  PCI VEN_1180 & DEV_0843 & SUBSYS_30CD103C
  PCI VEN_1180 & DEV_0843 & CC_088000
  PCI VEN_1180 & DEV_0843 & CC_0880

  ID of second base system device h/w

  PCI VEN_1180 & DEV_0592 & SUBSYS_30CD103C & REV_12
  PCI VEN_1180 & DEV_0592 & SUBSYS_30CD103C
  PCI VEN_1180 & DEV_0592 & CC_088000
  PCI VEN_1180 & DEV_0592 & CC_0880

  driver audio h/w id is

  HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5051 & SUBSYS_103C30CD & REV_1000
  HDAUDIO\FUNC_01 & VEN_14F1 & DEV_5051 & SUBSYS_103C30CD

  Please help solve

  Hello:

  For basic system devices, you need this driver...

  This package contains the driver and the host controller Ricoh 5-in-1 card reader for laptops models and operating systems.

  File name: sp37614.exe

  For the other device you need this driver...

  This package contains the driver for the Conexant HDAUDIO Soft Data Fax Modem with SmartCP (CX20548) in the notebook models and operating systems. This driver enables the remote access feature and provides a UI for formodem.

  File name: sp37817.exe

• The update to version 2 of Vitsa fail. Formatted hard drive to purchase the version. need to find the final vista product key

  The update to version 2 of Vitsa fail. Formatted hard drive to purchase the version. need to find the final vista product key

  It should be on a sticker on the box, or on the packaging.

  The product key consisted of 25 digits, divided into 5 groups of 5 digits.

  See you soon...

  Mick Murphy - Microsoft partner

• Cannot install windows 7-error: dvd/cd driver missing

  Try to install Windows 7 on a different SSD, but get an error indicating that the missing required cd/dvd driver.  How Windows load into memory from a cd/dvd that windows 7 says there is no driver missing?  This is the same installation disc that I used on a previous SSD without problem.  I have 2 other unused installation floppies, and each returns the error message.  This problem arose when an attempt to use System Restore Image I had done just on an external SSD and a drive hard usb.  The error I had to try to use one of them was that the Image was made in EFI and the computer seeks to restore in BIOS. It's the same machine.  Yes, disk management displays the UEFI 100 MB system partition.  The motherboard is an Asus F2A85 - V Pro.  List Disk running installation diisk sees only the cd/dvd and the drive hard usb but not the SATA drives.  When you normally use that List Disk sees everything.  The UEFI bios sees all readers, when you use the system installation disk.  I used a system repair disc made from the same computer at the same time as the picture of the system and used to start and got a system repair options is not compatible with this version of windows.  The windows version is 6.1.7601 sp 1 build 7601.  Any ideas?

  Hello

  Thank you for your response.

  There are two modes of starting particularly machine-> BIOS & EFI. BIOS is the general start mechanism found in most machines. Some of the machines also support EFI boot mechanism with BIOS

  Either the BIOS or EFI is set as the default in your machine - Please check start the installation system which

  one is active by default.

  If the EFI operating system is installed, it will create an EFI system partition in your machine. Installation of BIOS has no EFI partition.

  Warning in the BIOS: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful. Please feel free to post in the case where you are facing other problems with Windows, we will be happy to help you.

• mass driver missing

  My computer crashed again seagate HDD not new install and I'd get missing error mass driver. No presentation of drivers and nothing else in the USB ports. I formatted via the services window because it wouldn't show. Now it shows in Solution Explorer, but not formatting through properties or install a copy of fresh win7 drive, just to get HDD mass driver missing?

  Hello

  1. the CD worked fine earlier?

  2. have you checked the CD on other computers?

  If it doesn't there has no drivers on the CD, then you may need to contact the manufacturer and install the latest version of the drivers.

  http://www.Seagate.com/support/downloads/

  Let us know the results. We will be happy to help you.

• C309a printer driver fails to install, the drive M: on Windows XP

  C309a printer driver tries to install my drive M: on Windows XP.  Automatic installation of HP fails because the M: drive is not valid.  What should I do?

  Hello ChappyD

  If the problem is not with the printer but the computer that you got with the Agency. It seems that he may have had only a M:\ drive on the computer before and default installation of this drive that is obviously not valid, windows tries more based on the list of drives you provided previously.

  At this point, the best solution would be to re - install Windows on the computer.

  However, before you reinstall Windows try the following:

  1. Open the command prompt
  2. type: 'subst M: C:\. "without the quotes and press to enter.
  3. Restart and try to reinstall again.

  SOURCE: Officejet Pro 8500 wireless Error Message Invalid drive F: /

• Haw to download and install a driver missing for my memory card reader?

  Haw to download and install a driver missing for my memory card reader?

  Hello

  I'd be happy to help you. What brand laptop do you have? Is what model? And you know the brand of card reader? I need this information to find the right driver for you.

  Kind regards

  BearPup

• my printer is not recognized by my computer it says driver missing, I reinstalled it several times still does not

  my printer is not recognized by my computer it says driver missing, I reinstalled it several times still does not

  original title: printer driver

  my printer is not recognized by my computer it says driver missing, I reinstalled it several times still does not

  Is what printer? Where did you get the driver?

  That you download and install the * good * driver for him? It must be for Windows 7 and Windows 7 32-bit or 64-bit Windows 7, depending on what you are running.

• Adobe Application Manager corrupt - are trying to install the new copy will fail because the AAM is missing according to dump record installation - how to fix this chicken in the egg problem?

  Adobe Application Manager is corrupt and allows a reinstallation try Fail Adobe Acrobat Pro XI - try to install the new copy of the AAM fails because the AAM is missing according to dump record installation - how to fix this chicken in the egg problem?

  06/04/16 16:23:29:507. [INFO] |  | USS | PIM | PIM |  |  | 6256 | Build Version - 9.0.0.244

  06/04/16 16:23:29:507. [INFO] |  | USS | PIM | PIM |  |  | 6256 | Exploitation forest verbosity level set to 4

  06/04/16 16:23:29:507. [INFO] |  | USS | PIM | PIM |  |  | 6256 | CREATING Instance PIM...

  06/04/16 16:23:29:507. [FATAL] |  | USS | PIM | PIM |  |  | 6256 | Detected db journal file, Adobe Application Manager is in a State damaged to C:\Program Files (x 86) \Common Files\Adobe\OOBE\PDApp

  06/04/16 16:23:29:507. [FATAL] |  | USS | PIM | PIM |  |  | 6256 | Adobe Application Manager is needed to solve this problem. However, it is missing or damaged.

  Download a new copy of Adobe Application Manager of http://www.Adobe.com ,

  or re install this product.

  06/04/16 16:23:29:507. [FATAL] |  | USS | The installation program. The installation program.  |  | 6256 | Cannot create the PIM item

  06/04/16 16:23:29:507. [INFO] |  | USS | The installation program.  |  |  | 6256 | Event generated Guid is: "986b04a2-3099-49fd-9067-df69c36ff2b2."

  06/04/16 16:23:29:507. [INFO] |  | USS | The installation program.  |  |  | 6256 | Event generated Guid is: "e5f02581-649c-49ec-a265-800eeb5ad426."

  Does anyone have an idea what to do? I use Windows 7 as operating system

  Hi Ruedigerd91465945,

  Well try download and install Adobe Application manager from here: Adobe - Adobe Application Manager: For Windows: Adobe Application Manager: thank you

  Before installing kindly, restart the machine and then rename the folder in C:\Program Files (x 86) OOBE \Common Files\Adobe\OOBE\PDApp as OOBE_OLD

  Let us know if that helps.