The WLC and LDAP integration

Similar Questions

• unloading of feature to make dhcp off the WLC and put it on Active Directory.

  I need to use the feature of unloading to dhcp off the WLC and put it on Active Directory.  Someone at - it a walkthrough or a page for this?  I know it's just a checkbox and a redirect to the new dhcp server, but where the hell is the configuration on the WLC?

  Thank you!

  -anne

  You can go there.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01001001.html

  Point to your existing ad integrated DHCP server.

• improve the WCS and WCC integration / sync activity

  Hi all

  We have WCS integrated with WCC as backend storage of content. We use the STANDARD connector for integration between these 2 products suites. On check in content to the WCC, she undergoes life-cycle activities normal document and then contentid is placed in the queue of the integration table. Queue information will be collected and WCS will be synchronized with the information in document OWCC.

  This whole process takes longer (approximately more than 1 min) and users are not able to find the documents that they created immediately.

  Let know what steps can help solve or improve this performance. We did the analysis and concluded that unless the State of the document is PUBLISHED in the OWCC, information will not be placed in the queue table and synchronization of content is getting delayed.

  Indications will be very useful.

  The OOTB 'connection' is a polling station synchronization process (heart draws OWCC). It is not realistic to expect, it is a process in real time.   It can be as fast as the slowest part of the process - if you want Sites to poll more frequently change the "timing" in the system events. The desire to increase the frequency of audit of heart - but this will solve is not the question of the time it takes to the WCC from "creation of loan".

  If you want it to be more 'real-time', you need to create your own 'connection '.

  The folks over at Function1 and BezzoTech (https://www.youtube.com/watch?v=qVTS--OS78o) has created an interesting link where 'Document' is actually created in the OWCS UI and then automatically pushed in WCC and Sites 'at the same time;

• define the users for the studio and server Integrator

  Can you get it someone please let me know how to set the users for the studio and Integrator server so that the user can be used to display the page in the user interface but not change. I want to set the studio user that will access the Page but not modify it. And the user at the server of the Integrator must be able to view scheduled tasks.
  
  Thank you very much.
  
  Kind regards
  Amrit

  Amrit,

  Points are awarded automatically when you mark an answer (5 pts) useful or correct (10 pts).

  Is there a help icon in the label of the legend for the different rankings. The answer to your question is on this page.

  RLJII

• There's this red box around the URL and images integrated into Facebook... so I can't read it. I'm really untech saavy so please forgive me.

  I can somehow gives you a screen shot to show you the detail? How do give you it?

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  Note: This will make you lose all the Extensions, open Web sites and preferences.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

• The Lab Manager Ldap integration

  I, ve configured a vSphere/ESX environment of OTA in a subnet of 172.10.1.0/24.

  Open ports on our firewall to manage OTA from our direct environment. Online subnet: 10.128.0.0/16

  Installed Labmanager 4.0 and add it to the field in the environment of the OTA.

  Everything works fine. After you open the port 389, I want to synchronize LDAP.

  When I do "Test LDAP settings" I get the following error:

  

  I read that it is not best practice to place a LM server in a domain.

  http://blog.aarondelp.com/2010/03/VMware-Lab-Manager-install-notes-and.html

  I tried the Ldap synchronization with the server of LM in a working group, but also, it does not work.

  Tried with the domain admin user, manually add the ldap port, it was left empty, different DN, nothing worked.

  Read also in the article is not to name the server labmanager LM, and that's exactly what I did...

  Also the lab Manager folder described in the article was not created in vCenter.

  I think uninstall LM, rename the virtual computer and reinstall LM. I don't know if it will solve this problem.

  I hope someone has a solution...

  Thank you...

  the 'test' LDAP settings actually trying to find the account provided credentials.  It's like a back loop... I should be able to find me before as I find other people.

  If the test account is not in the basic DN path of research, but can locate other accounts then it should.

  Best regards

  Jon Hemming

• Customization of the user and Desktop Integration to connect security non - ADF

  Hi all
  Our application has its own connection authorization. I have some doubts about the MDS (personalization of the user between sessions) and integration of ADF Office for an application that doesn't use the ADF security.
  
  (1) is ADF Desktop integration taken in charge for the connection of non - ADF security. If so, is there a working example or how to establish a session to the user of the excel workbook with the username of connection of our application.
  
  (2) of this thread ( customization through the MDS user Sessions ), I understand that, if we write our own customization class, persistence of the MDS in the sessions should not be a problem. However, how we store this persistence to a database. Any example pointers / functional would be really useful.
  
  
  Thank you
  Bala

  Hi Balasumbramanian,

  I just write a 3 part series on SDM that should help you with the second http://www.oracle.com/technology/pub/articles/adf-development-essentials/index.html question. See, in particular, the third article ("part 10")

  John

• On the QML and C++ integration (getting "undefined")

  This subject has been discussed often and I went through a lot of discussions, but I have not found a solution for my problem so far.

  What I want to do in my application:

  I have a container that displays an html page. No, I want a part of the html page dynamically filled a C++ function. Here is my Code:

  // HTMLCreator.hpp
  
  #ifndef HTMLCREATOR_HPP_
  #define HTMLCREATOR_HPP_
  
  #include 
  
  class HtmlCreator : public QObject{
  Q_OBJECT
  Q_PROPERTY(QString html READ html WRITE setHtml NOTIFY htmlChanged)
  public:
      HtmlCreator(QObject *parent = 0);
      ~HtmlCreator();
  
      Q_INVOKABLE QString html();
  
      Q_INVOKABLE void setHtml(QString html);
  
  signals:
      void htmlChanged(QString);
  
  private:
      QString m_html;
  };
  
  #endif /* HTMLCREATOR_HPP_ */
  

  // HtmlCreator.cpp#include "HtmlCreator.hpp"
  #include 
  
  QString HtmlCreator::html(){
      return m_html;
  }
  
  void HtmlCreator::setHtml(QString html){
      if(html != m_html) {
          m_html = html;
          emit htmlChanged(m_html);
      }
  }
  

  // applicationui.cppPage* ApplicationUI::doLoadPageDetails(){
  
      qmlRegisterType("myHtmlCreator", 1, 0, "HtmlCreator");
  
      QmlDocument *qml = QmlDocument::create("asset:///PageDetails/PageDetails.qml").parent(this);
      qml->setContextProperty("app", this);
  
      HtmlCreator *HtmlCreator = new HtmlCreator();
      qml->setContextProperty("HtmlCreator", HtmlCreator);
  
      Q_INVOKABLE QString HTMLString = "";
  
      HTMLString.append("
   
  A
   a 
  ");
      HTMLString.append("
   
  B
   b 
  ");
  
      MinutesData->setHtml(HTMLString);
  
      Page* newPage = qml->createRootObject();
  
      AbstractPane *root = qml->createRootObject();
  
      return newPage;
  }
  

  // PageDetails.qml
  
  import myHtmlCreator 1.0
  
  Page{[...]Container {
          layout: DockLayout {
          }
          horizontalAlignment: HorizontalAlignment.Center
          verticalAlignment: VerticalAlignment.Top
  
          ScrollView {
              id: scrollView1
              scrollViewProperties {
                  scrollMode: ScrollMode.Vertical
              }
              layoutProperties: StackLayoutProperties {
                  spaceQuota: 1.0
              }
  
              scrollViewProperties.pinchToZoomEnabled: false
              scrollViewProperties.overScrollEffectMode: OverScrollEffectMode.None
  
              visible: true
              WebView {
                  id: webViewScrollable1
  //                url: "local:///assets/examples/test4.html"
  
                  settings.viewport: {
                      "initial-scale": 1.0
                  }
                  settings.zoomToFitEnabled: false
                  settings.textAutosizingEnabled: false
                  settings.defaultFontSizeFollowsSystemFontSize: true
                  settings.imageDownloadingEnabled: false
                  settings.binaryFontDownloadingEnabled: false
                  settings.cookiesEnabled: false
                  settings.javaScriptEnabled: false
                  settings.activeTextEnabled: false
  
                  html: " ...  lots of html code displayed correctly" +
                  HtmlCreator.html +
                  "" +
                  ""
              }
          }
  

  Now to the point where with HtmlCreator.html do I put her thong in the app I see "undefined" text

  What I'm doing wrong here?

  I found the solution!

  I missed to add my class as an attached object. So the container, the label or in my case WebView where I want to use the Q_Properties defined in my class, I have to add:

  attachedObjects: [
    HtmlCreator {
      id: htmlCreator
    }
  ]
  

  and then I can get the property

  htmlCreator.html
  

  But unfortunately
  the string I get is empty, so I'm still something missing here.

• Encrypted L3 Communications between the TOWER and WLC?

  Hi all

  I work with a client who wants to put the towers away to their WLC (a 4402). The problem is that communications between the TOWER and WLC must be secured, even through their private Wan! I have a few questions that result, if someone is able to help you;

  1. I can't know if and what method of encryption is (is it AES etc.?) used on connections between towers and the WLC and what are the steps?
     1. The terminology can be a problem here, it's not a wireless mesh, just classic LAP for WLC
  2. EXTENSIVE customer network is already encrypted (IPSec VPN via VPLS) in parts - what is the consequence of execution of AP<-->WLC with end to end (if possible) on a network encryption EXTENDED with IPSec, i.e. double encryption?

  Strange but true - pointers will be greatly appreciated... Phil.C

  With a controller of the 4400 series, the control traffic between the AP and the regulator is already encrypted AES.  The user traffic is not encrypted.  If you use a 5508 controller all traffic between the AP and the controller is encrypted AES.

  For what is running the traffic through a VPN, it should work.  The issue I see with this is with the MTU in general.  The controller will drop all packets with a payload of less than 32bytes data.  According to the MTU over the VPN I've seen packets getting fragmented and it is a question.  If you use one of the versions CAPWAP (5.2 or newer) discovery dynamic MTU is part of the Protocol and this MTU problem does not really exist.

• 1.3 of the ISE and NAC

  I have a client that 5508 WLCs runs through the area, and I'm catching IEEE802.1x authentication for the enterprise WLAN and WebAuth for WLAN of comments... they PSK now :(

  They have ad and ISE and NAC great interest, so my immediate thoughts are to integrate ISE AD and use ISE as RADIUS server for .1x on the WLC. Then use the WLC and ISE do WebAuth for comments... It's all of the standard stuff, but it gives the background.

  Now, we come to the interesting bit... they want to run BYOD. They are involved in the financial markets, so the BYOD must be tightly controlled. They ask on ISE coupled with the NAC, but I am not convinced that I need the NAC since the arrival of the ISE1.3. Of course, I will examine three (min) SSID, corporate knowledge, comments and BYOD, just logically distinct. I have nothing that ISE 1.2 cannot press the company and comments but BYOD must full profiling and reclamation prohibition or device before access to the net.

  Someone at - he comments or suggestions? Is ISE 1.3 enough NAC-like that I don't need more, or if this is not the case, what additional benefits does that ISE can support

  Thanks for your advice/comments/experiences

  Jim

  Hi Jim -.

  Version 1.3 offers an integrated PKI and a significantly improved services reviews experience. The internal PKI is nice if the customer does not have a PKI solution in place. Don't forget however that the PKI ISE internal can only issue certificates to BYOD devices which have boarded through the ISE BYOD "flow", you cannot use the ISE PKI to issue certificates to computers in the domain.

  With regard to the NAC: you need to specify exactly what is needed here. If you were to make "posture assessment" then ISE can do for machines based on Windows and OSX. You can check for things like: A / V, a/s, status of the firewall, Windows hotfixes. If you want to make the posture on mobile devices, so you will need to integrate ISE with MDM (mobile device management) solution such as: Airwatch, Mobile, Extend360 iron, etc. ISE may question the MDM for things like: the device is protected with a PIN, is the rooted device, is the encrypted device, etc.

  I hope this helps!

  Thank you for evaluating useful messages!

• How to record the numbers and words in the same file

  Hello:

  I did a vi where I record the spectrum and its integration in different positions of a two-dimensional net. I save the information in two spreadsheet with the comand "write to file measure."

  Now, I am recording the parameters initial positions, end X X and space between measurement points. I want a file with two columns that looks like:

  Initial position X 1000

  final position X 2000

  space 100

  But idon't know how to save the words and numbers in the same file.

  As I have to perform several steps I want to automatically choose the name of the file (something like parameters_1, parameters_2...)

  Thank you for your attention

  Hi bitxor.

  You can use all the functions of the WriteTotext file to write strings to a file.

  Then you could set up WriteToMeasurementFile' to add new data to existing files (instead of overwrite or renaming)...

  BTW. It is not a good idea to mix lvm files containing arbitrary spreadsheet data!

• AP failed to connect with the WLC.

  We have 5 sets of 1700 APs works on the mode of the controller and cisco WLC 2500.
  I configured the controller as I always used to do, but this time the access points have been unable to reach the controller.
  That's what I did:
  controller IP address:192.168.1.250/24
  GW:192.168.1.1
  Primary DHCP: 192.168.1.250
  I have connected the port1 controller with ethernet cable from the switch and the same switch I connected the AP.
  We used the adapter instead of the POE switch.
  I even tried assigning address to AP directly through the console as:
  CAPWAP ap controller ip address and so on. This did not help either.

  There was this message in the AP "% CAPWAP-5-DHCP_RENEW: could not find WLC by using DHCP IP." DHCP IP renewal. "
  Moreover, the POE ports in the controller, they provide enough energy for the PA to operate?
  Help, please.
  I have attached the PuTTY log as well.

  Hello
  WLC connection has successfully been created. Then he for some reason any. I don't know if this helps, but try to connect the ethernet cable directly to the AP instead of port POE port to THE.
  You can use port POE on AP even if you don t use the POE switch.

  And regarding the port POE on WLC. Cisco doesn´t recommend that you directly connect AP to WLC, but it is possible.

  Also I Don t see that the IP address is assigned by DHCP.
  Try also to use the commands:
  CAPWAP ap ip address...
  CAPWAP ap ip default-gateway...

  I guess the WLC and switch are configured correctly.

  EDIT:

  I had similar problem today.
  Just connect the cable from the console to AP, go to mode and type the commands:
  Claire capwap private-config
  Claire lwap private-config

  then reload AP with command "reload".

  After these commands AP joined succesfully WLC

• WLC4402 - Questions to upgrade the AP and controller

  Hello

  I just upgraded an AIR-WLC4402-12-K9 to version 7.0.98.0 of the software, and I have a few questions-

  1. I have no APs to connect yet but when I do I'll have to check what software they run and perhaps demote the controller to get access up to v7 points?  To join the WLC v7 since v3.2 I had to make a few intermediate upgrades and I wonder if I have been a little premature and should have done updates after the APs have been associated, has new software pushed from the controller and then performed the steps in upgrade of WLC so the WLC and APs were synchronized in terms of software.

  2 - the memory usage is sitting at 60% with no associated APs.  I have just connected 4402-12 running 5.1.151.0 and he's sitting at 33% use of memory with associated access 11 points.  Have I spent in a too recent version for this controller?  What is a figure of the memory use of a 4402?

  Thanks in advance,

  Jason.

  Jason,

  A question.  You should be fine.  When the AP detects the WLC, it will do a code audit.  If this isn't the right code, it can extract the correct image of the WLC.  As long as the AP you are supported in 7.0, the recovery on the access point image won't matter.

  For question 2.  sounds of 60% of normal for 7.0, depending on the amount of memory is on the device itself.  I woulnd't ' t be too concerned about the memory usage until you points upward in the high 80 years.

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Why did did you spent much time for the integration of the Pocket and not in the resolution of the 'impasse' - vulberability?

  The deadlock problem solved no?
  I think it is more impotant than the Pocket-integration.

  You can also switch the prefs involved to false on the topic: config page.

  • Security.SSL3.dhe_rsa_aes_128_sha
  • Security.SSL3.dhe_rsa_aes_256_sha

  You can open the topic: config page via the address bar.
  You can accept the warning and click on "I'll be careful" to continue.

  • http://KB.mozillazine.org/about:config

• Replacing the fan for w/15.4 "screen and GPU integrated T60

  Greetings,

  The combo fan/heater several months ago, I bought for my T60 was apparently the 41W6409 for a T60 with discreet gpu and cpu, but mine is an integrated model that uses the 41W6408.

  As I can't return it, I was just thinking to replace the old fan with that on the new heatsink. But I'm not sure that it will fit, being the only FRU I could find for the Fan/Heatsink combo.

  So, I was wondering if someone here who happened to know if these fans are the same.

  Thank you very much in advance.

  Steve

  Skater wrote:

  Greetings,

  The combo fan/heater several months ago, I bought for my T60 was apparently the 41W6409 for a T60 with discreet gpu and cpu, but mine is an integrated model that uses the 41W6408.

  As I can't return it, I was just thinking to replace the old fan with that on the new heatsink. But I'm not sure that it will fit, being the only FRU I could find for the Fan/Heatsink combo.

  So, I was wondering if someone here who happened to know if these fans are the same.

  Thank you very much in advance.

  Steve

  Steve, you can use the unobtrusive radiator on your integrated motherboard. In fact, the best option in my opinion is to go with a T61 heatsink that is designed to cool the much more powerful X 3100 graphics and uses the thermal paste rather than pads type blade of silicone used to cool graphic systems T60. Alternatively, you can replace these pads with thermal paste on the heatsink T60 but unity T61 is better in my opinion. I can't tell you if the fans are interchangeable, because there was more than one fan used on the T60 models intel, some were, and some were not. There was also a discreet couple different sinks of heat, but will be more than enough for the cooling of your integrated graphics. Platform which cools the discrete gpu will not be used so it isn't a problem and cooling chipset platform will suffice for the cooling of your integrated graphics.