AP failed to connect with the WLC.
We have 5 sets of 1700 APs works on the mode of the controller and cisco WLC 2500.
I configured the controller as I always used to do, but this time the access points have been unable to reach the controller.
That's what I did:
controller IP address:192.168.1.250/24
GW:192.168.1.1
Primary DHCP: 192.168.1.250
I have connected the port1 controller with ethernet cable from the switch and the same switch I connected the AP.
We used the adapter instead of the POE switch.
I even tried assigning address to AP directly through the console as:
CAPWAP ap controller ip address and so on. This did not help either.
There was this message in the AP "% CAPWAP-5-DHCP_RENEW: could not find WLC by using DHCP IP." DHCP IP renewal. "
Moreover, the POE ports in the controller, they provide enough energy for the PA to operate?
Help, please.
I have attached the PuTTY log as well.
Hello
WLC connection has successfully been created. Then he for some reason any. I don't know if this helps, but try to connect the ethernet cable directly to the AP instead of port POE port to THE.
You can use port POE on AP even if you don t use the POE switch.
And regarding the port POE on WLC. Cisco doesn´t recommend that you directly connect AP to WLC, but it is possible.
Also I Don t see that the IP address is assigned by DHCP.
Try also to use the commands:
CAPWAP ap ip address...
CAPWAP ap ip default-gateway...
I guess the WLC and switch are configured correctly.
EDIT:
I had similar problem today.
Just connect the cable from the console to AP, go to mode and type the commands:
Claire capwap private-config
Claire lwap private-config
then reload AP with command "reload".
After these commands AP joined succesfully WLC
Tags: Cisco Wireless
Similar Questions
-
Failed to connect with the user name "Administrator".
Hello
I want to configure vCD in VCO, but I am faced with error. I'm by train through the configuration of the vCO.
I get the error message https://10.99.133.212:443 , Failed to connect with the user name "Administrator". And the description of the error is: "the API version information could not be obtained for the host https://10.99.133.212:443 () (administrator@System)!'."
Here are the entries I provide:
Host: 10.99.133.212
Organization: System
Authentication: basic
Session: shared
and name of user and password.
What could be the error here? My vCO has IP 10.99.129.33. And I imported the vCD also SSL certificate.
Kind regards
Bethy
You must first remove the new plug-in...
VMware KB: Uninstall a plug-in for VMware vCenter Orchestrator
Remember that you use step 6.3 in this article to delete the contents of the package as well. To verify that the workflow and actions have been removed, check that the following workflow category (and all children of it) no longer exist:
/ Library/vCloud Director
And all related Action modules should have disappeared as well:
com.vmware.library.vCloud. *.
Once you have completed all steps of the KB, install version 5.1 of the plugin, configure and restart the vCenter Orchestrator Server service, once again to complete the installation.
-
Hello to you all,.
I have a great fun for you guys. If you're curious, it's here...
I just bougt garage a portege Toshiba Portege Z30t-A-126 PT24CE-01400HFR
Nice machine but SSD is too small, so I changed the original SSD 256 to a 512.Reinstalled Win7 completely without any pb.
Just a pb in fact: the footprint software does not work.
When I hliant, it fails and says "unable to connect with the sensor.In french "fingerprint recognition."
Unable connect the sensor.But when I check the Device Manager computor it says that everything is in place and ongoing execution, validity (WBF) (PID = 0010) sensors works very well and the latest version of the driver is installed.
(I downloaded the form driver toshiba Web site.) The name of the driver is fp - sw - 20140115084521.zip)Then? What's not?
I spent hours searching the web and tried everything I could. Reinstalled a thousand times the drivers, software, tried other drivers... But there is no way that I can fix it.
It's really annoying...Can someone help me please? Have you an idea? I'm stuck...
Thanks in advance. :-)
Hello
This issue of the fingerprint has been described in another thread.
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=81261You should be able to solve the problem installing the chipset driver.
Another user said, an installation of Proset Ethernet drivers/software was necessary to get the problem resolved. But to be honest that I put t think that missing Proset utility would cause the questionHowever, check it out.
Your comments would be appreciated
-
Original title: cannot backup Windows 7 system.
When I try to back up the system or create the image of the system I get the following message, the error was detected in the Volumn Service VSS (Shadow Copy) the problem occurred while trying to connect with the VSS writers. Verify that the event system Service and the VSS service are running and look for errors related to event logs. (0 x 80042318).
Hi bernardolahoustino,
Please keep us informed. Please let us know the State of the question, so that we can help you further.
-
Error when you try to import
WARNING: Unable to update the preferences of the user
Cannot establish a connection with the server of history. Service could be down. Please try again later.
Can you please try again? Please let us know if you still experience this issue.
-
Utility of fingerprinting Toshiba - "Failed to connect to the sensor.
Having a problem with the Toshiba fingerprint utility. The program works fine until I try to use any sort of firewall/antivirus program, even the built-in Windows Firewall: S the scanner still works fine for the boot time scanning, as well as for windows logonm but as soon as any kind of firewall/antivurus software loads up, it fails to connect on the sensor. I added the program to the lists allow but still nothing... So far I tried with AVG Internet Security, Outpost Security Suite and by default, the Windows Firewall. Windows Firewall turned on for awhile, I got when I bought the laptop and there was no problem.
It's a Qosmio X 500 - 00 X, it uses the same installation of windows when I bought...
See you soon!
Hello
Please update the software of fingerprint. You can find it here:
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download driversAlso try a different firewall and AntiVirus. I have good experiences with AntiVir and Kaspersky Security Suite.
-
Drive not work in IE and saying failed to connect with fingerprint sensor
Hi all
I purchased a Qosmio x 500 10 t a couple of months back. For the first two weeks, I had no probs using the fingerprint reader to log on windows and connect to Web sites in Internet exploer.
All of a sudden it would not work on any website that is stored. The Green banner was shown in the upper part of the site and asked finger drag, but nothing happened when I slipped. I rebooted and it worked again but not for long before failing. This time a restart didn't work so I deleted my fingerprints and Web sites and started from scratch. It worked for a few attempts before probs started. And to try to enter the utility of fingerprint it says the connection of sensor failure. So, I did a system restore. He worked for some time yet and then same probs. So I found the update utility software, uninstalled the old and put on the new. Even once worked for a couple of times then failed.
I couldn't find anything about it is stuck in the registry but to be on the safe side I did a full system own return to the original using disks of backup configuration. Hey presto, I thought that he had worked. Everything goes ok for the first 24 hours and then same problems start to occur. Only this time it's also prompting me to register fingerprints even if I already have. And when I try to enter the utilioty it says cannot read the sensor again.
The fingerprints for windows log still works as long as I do not close the utility of fingerprinting before stopping. If I quit the utility I can't reopen it as it says failed to connect to the sensor only. And then I have to uninstall and reinstall the utility software. Aty at the time where he occasionally works on sites stored Web, but most of the time it does nothing.
Help, please. I have to return Toshiba laptop?
Have you seen this FAQ?
+ Log on to websites with Authentec Fingerprint Software (TrueSuite) and Internet Explorer 8 +.
http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=62I recommend looking in the forum and read the HowTo and FAQ section in this forum
Could still be interesting -
Fails to connect to the Proxy Server
My internet works but are used. He says he "fails to connect to the Proxy Server" is due to firewall settings? and how to change them.
Your message is in the forum for people needing help with the anti-malware program from Microsoft Security Essentials (MSE).
Suggest you contact support OBJECTIVE to: http://help.aol.com/help/product/aim/
-
I have reported this problem on my PC at home that connects to the internet. My laptop runs Vista Home Premium and I can't connect to the internet. I took my laptop on a trip, tried to connect to the wireless network that was free to the place we are. Could not connect, and after this initial test, the following is displayed after the start of "failed to connect to the Windows Service, Windows cannot connect to the system event notification service. This problem prevents limited users to logon to the system. As administratvie user, you can view the system event log to see why the service did not respond. "(have no idea how or what it means) when I go to the task bar you want to connect to a network, it is said:" the dependency service or group could not start"and if I go ahead and press"connect to a network"it says it can't find. I search for computers on the network (who I'm sitting next to) and then try to diagnose the problem and it cannot. I have limited knowledge of this type of problem. Anyone have this problem and how to fix it?
Hi ptkein,
Thanks for posting your question on the Forums of Windows Vista.
Option 1: You can download and install the latest network card drivers and see if that can solve the problem.
Option 2: Follow the link below to fix network connection problems
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
Option 3: Follow the link below to solve Internet connection problems
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems
Option 4: To verify if a third party application is a cause, follow this link (http://windows.microsoft.com/en-us/windows-vista/Advanced-startup-options-including-safe-mode) for this boot to the desktop using the safe mode with networking option and try to install the network. If the problem is resolved, you will need to perform a clean boot by following the steps in the following article to refine the exact source and isolate it: http://support.microsoft.com/kb/929135
Let me know if it worked.
Hope it will be useful.
Thank you and best regards,
Kadoch - Microsoft Support
Visit our Microsoft answers feedback Forum and let us know what you think.
-
It's VERY odd and very annoying!
I set up my laptop next to my Xbox 360 with an Ethernet cable directly connecting the laptop to the XBOX, and the laptop is on our wireless network. The XBOX has access to the internet (shared through the laptop), and when I test the PC connection and the connection XBOX Live sound fine to all.
So I'll try to set up Windows Media Center, it works great! I "Add Extender", put the code to 8 digits. It passes through the installation, all works, no problems and WMC opens on the XBOX, I can go into my library, watch movies etc... works great!
However! As soon as I turn my XBOX off and back on, it will fail to connect to the WMC.
He says his 'find Windows Media Center PC' which seems to work fine, it goes to the ' Windows Media Center loading screen "contact...". ", and after about 10 seconds, I get an error"failed to connect the Xbox 360 could not connect to windows Media Center PC. Make sure that the PC is turned on and connected to the network.
I tried to configure the Extender repeatedly, whenever it works fine until I restart the XBOX... :/ - and its strange cause I still the internet connection (shared through the laptop) after turning on the XBOX, its really JUST Media Center which is screwing around.
She continues to keep trying to connect then repeatedly fails.
If I wanted to, I could re-configuration the WMC Extender EVERY TIME turn off the Xbox, which works the first time without fault, but that's all just stupid.
I can't really understand what is happening here... any help would be appreciated.
Hello
Refer the article that could help you solve this problem.
http://support.Microsoft.com/kb/932163 -
I am trying to use the new functionality of Log Viewer PeopleTools 8.55.
It is a great improvement that allows developers/testers/support team members to display the application server logs, process scheduler logs and newspapers PIA; with a regular account of the PeopleSoft Application.
You have no need to create a system account on the server (Linux or Windows) for users to view the logs.
I managed to configure the Web server log viewer, but when I try to Application I can see message failed to connect to the JMX service (209,1046).
When I configure the JMX for APPDOM user, I tried PTADMIN with no success.
Could someone describe the process to change the JMX user for Tuxedo domain?
Thank you
Stéphane.
the default installation of DPK password is password.
Kind regards
/ Stéphane.
-
Unable to connect with the DNS server
Recently, I went away for the weekend and came back to find that I had no internet, on all devices... So I don't know exactly how long he was out. I'm a computer and a network engineering student and I've tried everything I can think of to make it work again. Here's what I did:
First off troubleshooting generates an error message: "failed to connect to the DNS server.
Of course, I did reboot of the habit of my router and my devices.
I can't connect to WiFi or direct connection via Ethernet. I tried flushing DNS via the command-line ("ipconfig/flushdns") as well as the command "netsh int ip reset", "ipconfig/release" and "ipconfig / renew." I tried to go into the settings of the network adapter and the two affecting the IPv4 and IPv6 DNS google DNS settings. I even traded my router for a new with my ISP (of Roger (Canada)). I have connected to my router through my web browser and tried to change some of the DNS settings there (everything went well). Nothing worked so I have everything set to default. I tried ping around my own network, I ping my own card NETWORK, but also the entry door, so I know that's not my PC, I have also excluded because all my devices do not work. I spoke with Rogers (my ISP) twice now and they were no help at all, they were more concerned by the flashing lights on the router as the real problem. I'll have a technician to the course to watch tomorrow, but I doubt they'll be any help at all. I wouldn't say I'm a computer genius, but I have a pretty good understanding of how things work and I can not understand what the problem is here, I can have forgotten something or forgot to mention something I tried. But if anyone has any ideas, or similar cases they decided that I would be VERY grateful for the help.
Hello
Thanks for posting the query on the Microsoft Community Forums. You have reached the right place. Let us work together to find the cause of this problem and try to solve.
There could be various reasons for which you will not be able to connect to the Internet. And I'm glad to know you have try more troubleshooting steps to solve problems.
1. which antivirus program is installed on your computer?
2. don't you make changes to the computer before the show?I suggest you try the steps from the following link and see if that helps.
Why can't I connect to the Internet?
http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-8Wireless and wired network problems
http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1Let us know the update after trying the steps above.
-
Unable to connect with the Mac computer?
Unable to connect with the Mac computer?
Please read https://forums.adobe.com/thread/1499014
-try some steps such as changing browsers and disable your firewall
-also clear the cache of your browser if you start with a fresh browser
-Run "Difficulty Host File" option https://helpx.adobe.com/creative-cloud/kb/cc-cleaner-tool-installation-problems.html
http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip.
https://helpx.Adobe.com/creative-cloud/KB/creative-cloud-desktop-application-failed.html
http://helpx.Adobe.com/creative-cloud/KB/failed-install-creative-cloud-desktop.html
-
Failed to connect to the user when it connects to SQL Server 2008 R2 gateway
Hi - This is my first post!
I have problems to connect to a SQL Server 2008 R2 to Oracle database 11 g R2 database, use the product of the gateway.
Previously, he has worked, but we moved the database SQL 2005 to 2008 (R2).
We receive this error while trying to query through the link (Select * FROM DUAL@ADSRD)
ORA-01017: name of user and password invalid. connection refused
[Oracle] [ODBC SQL Server driver] [SQL Server] Failed to connect to the user 'SQLUSER '. {NativeErr 28000, = 18456} [Oracle] [ODBC SQL Server driver] Invalid connection string attribute {01 S 00}
ORA-02063: preceding 2 lines of ADSRD
01017 00000 - "invalid username/password; connection refused '.
* Cause:
* Action:
Error on line: 1 column: 35
The DG4MSQL configuration is here:
HS_FDS_CONNECT_INFO = //SSU_PRD_APP/IntegrationStagingDb [BSYS-sql2]
HS_FDS_TRACE_LEVEL = OFF
HD_TRANSACTION_MODEL = READ_ONLY
#HS_FDS_DELAYED_OPEN = FALSE
HS_FDS_FETCH_ROWS = 100
HS_OPEN_CURSORS = 50
The database is hosted in its own instance on the sql2-BSYS Server
Then... on the SQL Server event logs returns this:
Failed to connect to the user 'SQLUSER '. Reason: Failed to try to connect using SQL authentication. Server is configured for Windows authentication only. [CLIENT: 192.168.10.179]
However, the SQL Instance IS configured to enable mixed mode authentication.
I can't work on what I missed, and I can confirm if I'm actually to a compatibility issue between the gateway and the version of SQL server, that we are now trying to connect.
Help please!
Is the user name in your SQL Server database in the capital, mixed mode letters or small letters?
Currently, you have created a database link that tries to authenticate on the server SQL using SQLUSER in capital letters. If you use mixed or small letters, so be sure to write the user name (and password) as it is in the create database link statement and surround it with double quotes.
If you have created the link of database correctly, try an ODBC connection for example from your client and add the user name and password. Does it work?
-Klaus
-
Unable to connect with the listening port of the client
[oracle@rac31 ~] $ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on March 21, 2014 03:33:30
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC) (KEY = LISTENER)))
STATUS of the LISTENER
------------------------
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start date March 20, 2014 13:33:30
Uptime 0 days 13 hours 59 minutes 59 seconds
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file
The listener log file /U01/app/Oracle/diag/tnslsnr/rac31/listener/alert/log.XML
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = LISTENER)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.101) (PORT = 1521)))
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=192.168.1.111) (PORT = 1521)))
Summary of services...
Service '+ ASM' a 1 instance (s).
Instance '+ ASM1' READY State, has 1 operation for this service...
'Cars' service has 1 instance (s).
Instance "rac1" READY State, has 1 operation for this service...
Service 'racXDB' has 1 instance (s).
Instance "rac1" READY State, has 1 operation for this service...
The command completed successfully
In my server in the Oracle_HOME/network/admin
This is my entry in tnsnames.ora
RAC =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP) (HOST = rac-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = rac)
)
)
I am able to connect with the command
sqlplus system/password@rac
However, when I give the same input on the client computer
It does not work
I am able to ping the host rac-scan successfully
C:\Users\rgehi > ping rac-scan
Ping rac - scan.oracle.com [192.168.1.113] with 32 bytes of data:
Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64
Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64
Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64
Response from 192.168.1.113: bytes = 32 time < 1 ms TTL = 64
Ping statistics for 192.168.1.113:
Packets: Sent = 4, received = 4, lost = 0 (0% loss),
Time approximate round trip in milli-seconds:
Minimum = 0ms, Maximum = 0ms, average = 0ms
C:\Users\rgehi > sqlplus system/password@rac
SQL * more: Production of the version 12.1.0.1.0 Fri Mar 21 03:40:53 2014
Copyright (c) 1982, 2013, Oracle. All rights reserved.
ERROR:
ORA-12545: Connect failed because target host or object does not exist
I installed oracle client on my desktop
and I made entries in the tnsnames file
However when I connect to the database to rac with scan it works sometimes...
not always...
so I'm in search mode and finally, after many moons a lot and light years away, I found the following
Here's what I did
# - scan192.168.0.127 rac31 - scan.oracle.com rac31-scan
192.168.0.128 rac31 - scan.oracle.com rac31-scan
192.168.0.129 rac31 - scan.oracle.com rac31-scan
I put three ip addresses in the host with the same name rac31-scan file
then I put the same ip addresses in my windows hosts file
Here are the entries
192.168.0.127 rac31 - scan.oracle.comrac31-scan192.168.0.128 rac31 - scan.oracle.com rac31-scan
192.168.0.129 rac31 - scan.oracle.com rac31-scan
but in the (windows 7 pc) client tnsnames file has just one entry
It's here
RAC1 =(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP) (HOST = rac31-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = RAC)
)
)
and now when I connect from the client... it connects without any problems.
I have tried more than 10 attempts without problem
BINGO!
Maybe you are looking for
-
Satellite P30-133: where can I find the drivers?
HelloI lost my recovery discs, so I installed windows, is one know where I can find all the drivers to download? I find all the other models but not mine? also, anyone know how much it costs to buy the new recovery disc? Thank you
-
Satellite M65-S809: change in CPU Question
I have toshiba satellite M65-S809 CPU pentium M740. I would like to change processor pentium M770. Can I do this? What is the highest quality of CUT, I can go to?
-
How to recover photos from an iPhoto rebuild that occurred and delete all my photos?
I have a Macbook Air running OS X Yosemite 10.10.1 and has been using iPhoto, when he told me to make a reconstruction of my iPhoto application to continue to use it. My only option was to move forward, but when I did, the app rebooted and deleted a
-
I installed all the drivers, but only one left in the list. This is the "USB controller driver. I've also attached a screenshot of the Device Manager screen. Please any body help me find this driver to make me finally get rid of all the "unknown devi
-
Can I replace a hard drive of PC HP Pavilion ze2068EA to an another HP Pavilion Ze2348ea laptop? Best regards Khalid Please send your reply to this mail RMT. [email protected]