This PSU and GPU will work with my dell inspiron 660?

Similar Questions

• An XFX Radeon 7850 will work on my Dell Inspiron 660?

  It is not the slim version. "The size of the graphics card are 7.8"x 4.4"x 1.5"
  I noticed that the hard drive uses space and limit to how long something in the PCI slot can be, but I did some steps and 7.8 length must adapt. However memory modules are worrying me. will they get in the way of the graphics card as they are really close to the end of the PCI-E slot? I already know to pass the power supply, so I have a Corsair CX 750. In addition, the graphics card will work on the PCI-E to inspire x 16 slot if the interface of gpu said PCI-E 3.0 x 16?

  Here is a picture of the chassis

  http://media.community.Dell.com/en/CommunityServer.components.imagefileviewer/CommunityServer/discussions/components/files/3515/6116.Inpiron%20660b.jpg-550x0.jpg?m=635018077965100496

  and here's the gpu that I plan on getting

  http://www.newegg.com/Product/Product.aspx?Item=14-150-617&SortField=0&SummaryType=0&Pagesize=10&PurchaseMark=true&SelectedRating=-1&VideoOnlyMark=False&VendorMark=&IsFeedbackTab=true&chkPurchaseMark=on&Keywords=%28keywords%29&Page=1#scrollFullInfo

  Hi crayolaboy18,

  Thanks for the photos and links. They were very helpful.

  Modules of memory will not impede the map, so you can go ahead and get the upgrade. Its good that you upgrade the PSU too. Here take a look at the photo below, the graphic card XFX begins to protrude out of the base, which means that the body of the bulges of the slot card Express for PCI card locations. Thus, he will not come in the way of the memory modules.

  

  

  The red highlighted area above is taken by the card. And the answer to your PCI express 3.0 application is in the image below:

  

  I hope this helps.

• What graphics card will work with my Dell U2711 to 2560 x 1440?

  I just bought a Dell U2711 monitor I want to use with Photoshop at its native resolution of 2560 x 1440. I also have a Dell E2311H to use dual monitor with it in a configuration.

  The monitors are connected to a card mother with an integrated video chipset ATi Radeon 4200 with DVI - D and regular 15-pin output video under AMD Gigabyte MA785GM.

  However, the 4200 chipset does not seem to support the resolution 2560 x 1440 Dell as all I get are blurry tinted color characters. The ClearType text gives me just blurry garbage.

  I use the Dual-link cable that comes with the Dell U2711.

  What cheap graphics cards will work for me with this arrangement of material?

  Refresh rate is not important. I'm not a gamer.

  This video card has two DVI and DP and 2560 x 1440 60 Hz will do.

• This "Recovery disc" option will work with my PC?

  I have a client who is an emergency wants to start to use their computers again (a HP Pavilion p6347c windows 7 Home premium 64-bit, product #: ay614aa #aba), so I have to stop chasing dead ends and ask them to buy a new PC - if it's what ultimately will happen anyway.

  The SATA hard drive is dead. I installed a new, but we need the recovery disks to reinstall the OS Win7. I was all prepared to order on Friday evening on the HP site recovery disc, I was on the screen to enter a credit card number and I stopped to confirm the purchase by the customer, and when I got home, the hp recovery disk order online site had declined, until ' Sunday 26 9:00 AM CST. But this time has passed and the site is still not up. I have a bad feeling.

  My work depends on not wasting any more time. I need to know the following:

  (1) the Web site will go online at any time in the next 24 hours? (was supposed to be lifted this morning)

  (2) my "build NUMBER" is "a1nav6pra2". The link
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063 & LC = on & CC = US & DLC = in & sw_lang = & Product = 4120...
  I intend to use to order my recovery discs says:
  "windows 7 64B a1nav6pra1 + supp 7 recovery kit.
  That is to say. "a1nav6pra1" instead of "a1nav6pra2". The gap of a figure is a problem?

  (3) HP recovery discs check the hardware to ensure that the material matches. I replaced death hard drive HITACHI (HITACHI 640 GB 7200 RPM SATA-II 16 MB of buffer "HDT721064SLA360") with a new SATA hard drive (SEAGATE st3500641as-rk, 500 MB, 16 MB cache, 7200 RPM).
  Is there a reason the recovery disks will not be installed on this drive?

  Thanks for any help!

  You can also call HP to the 800-474-6836 and ask to order a set of disks. The disks should work even with the gap of a figure. Sometimes, the recovery discs are reluctant to a hard drive that is smaller than the original disc to factory.

  You can also order the recovery of ComputerSurgeons.com disks

• (Redirected) GPU that will work with my dell optiplex 780

  Hello. I recently bought a dell optiplex 780 desktop computer (DT). I want to increase the power of the GPU, but I don't know what are the options I have or what I can get. I mainly play minecraft and MMORPG games. Does anyone have suggestions for me to be able to get without breaking the Bank or buy a new power supply? If you could help, I would really appreciate it. Thanks again.

  Data sheet:

  CPU: Intel Core2Duo E7600 (3.06 Ghz)

  RAM: 4 GB (I don't know if its DDR2 or DDR3)

  GPU: Integrated (it seems an Intel GMA 4500)

  OS: windows 7 (64-bit)

  link to the PDF of the dell optiplex 780 (the one I have is the desktop Dell Optiplex 780 (DT)

  www.Dell.com/.../optiplex_780_tech_guidebook_en.pdf

  Hi R3DSTON3R,

  Please repost this in the forum Office help.

  http://en.community.Dell.com/support-forums/desktop/

• What graphics card will work with the Dell Dimension E520

  Hello

  The graphs that accompany my Dell Dimension E520 isn't good enoght. If I am considering upgrading the graphics card, but I don't know what kind of my Dell Dimension E520 graphics card will support.

  Thank you

  
  

• If I purchased this computer about 4 months ago I can support windows 7 free? and the 64-bit system will work with windows 7

  If I purchased this computer about 4 months ago I can support windows 7 free? and the 64-bit system will work with windows 7

  This is the Forum for Windows Update.

  How does the Windows 7 upgrade Option?

  The Windows 7 upgrade Option is available through participating PC manufacturers on some PC and Microsoft on any purchase of packaged product Windows Vista. The Windows 7 upgrade Option applies to Windows Vista Home Premium, Business and Ultimate editions. Your upgrade to Windows 7 will be the comparable version: so you will get either Windows 7 Home Premium, Windows 7 Professional (upgrade to Windows Vista Business) or Windows 7 Ultimate, respectively. The Windows 7 upgrade Option program works on June 26, 2009 through January 31, 2010.

  http://www.Microsoft.com/Windows/buy/offers/upgrade-option.aspx

  Above Microsoft link has info for the Options to upgrade Windows 7 from participating computer manufacturers.

  Read the info here to see if you qualify.

  http://www.Microsoft.com/Windows/buy/offers/upgrade-FAQ-option.aspx

  FAQ about the upgrade is at the link above.

  http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

  Windows 7 Upgrade Advisor.

  http://TechNet.Microsoft.com/en-us/library/dd772579 (WS.10) .aspx

  Railways upgrade to Windows 7 at the link above.

  For any other question of Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 forum for questions on windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Pavilion HPE h8-1214: GPU EVGA GTX 750TI will work with my HPE h8-1214

  Hello. I plan to update my graphics card soon. Accoring to this, I have a card Mother Angelica. I read another post here of a user having a h8-1230 with a card Mother Angelica Revision2 , who said the EVGA GTX 750TI was inconsistent with this Council, and that he should look for a version of the 750TI MSI instead.

  I was wondering if the same applies to my PC because my model is older that the other user has been. I prefer to use the EVGA GPU version, as it is cheaper than the MSI one, but I need to know if it will work with my computer. If not, will the labour card ASUS model, or should it be MSI? The map I intend to buy is present (EVGA) or this (ASUS).

  In addition to this, does anyone know if the stock fans and 300W power supply provided with this computer would be appropriate for the new card, or not? I'm looking forward already pass the power supply, but I don't know for the fans. If I were to upgrade the PSU, 430W would be enough, or should I go with 500W? Thank you.

  If anyone in the future who might wonder, I had this GPU works on my computer, but I had to buy a specific version of the map and the way I got it to work was pretty weird.

  You need to buy this version MSI of the card, because the card itself has a switch on to change the UEFI to Jack supported BIOS Legacy. As far as I know, other versions of this card are UEFI only, and this computer does not support UEFI, so he needs a card that can run in the traditional way. It may look like a fit snug in the case, but it does not seem to cause problems and it cools very well with fans.

  I also changed to a block of power SUPPLY Corsair 430W, which seems more than enough for the system, even with the card to load max. You could go to a higher power, if you consider the upgrade of several pieces, or reuse the power supply in a more powerful system later. I have not upgraded fans in the computer and do not seem to have cooling problems.

  Now to make it work...

  I had some questions:

  When I first turned on the computer, it froze on the screen of the POST (the first screen with the HP logo). It would allow me to get into the BIOS, and it would beep 4 times (with long breaks between the two), before finally to a black screen with a cursor blinking and just stay there.

  What finally got it to work:

  I disconnected all the instructors of the map (cables VGA, DVI or HDMI), and then I turned on the computer. Without any monitor plugged, the computer should beep 6 times (the power button LED flashing with it), then the power led turns off. The LED went off as soon as I plugged my monitor into the computer (in my case, I used a VGA cord).

  For the first few seconds, the screen remained blank and does not save a connection. The computer is beeping intermittently for a while, then after about a minute my detected monitor suddenly a signal, and the screen displays the Windows splash screen. I was able to boot into Windows, all right, even if the resolution of the screen will be a little goofy, until you install the drivers.

  I jumped in the driver installation CD, and once it finished installing, I restarted the computer. Now, when it restarted, I had to do the same procedure I mentioned above so that he could start again. Now that the drivers are installed, I don't know if I'll have to do this procedure everytime I restart the computer (don't have not shut down since then), but since I rarely shut down my computer, it's worth it to me.

  Hope this helps someone else, because I know that I spent 10 hours searching for ideas before discovering this solution myself.

  Now that it is running, I have problems and I have run several graphics intensive games on it without any problem with cooling or power draw. It is very quiet, too. Even with a game running on high quality graphics, I can barely hear the fans when there is no other sound in the room.

• This power supply will work with my PC?

  This power supply will work with my PC?  I have a Compaq Presario SR5816F

  http://www.Newegg.com/product/product.aspx?item=9SIA4CP1GF8726&cm_re=power_supplies_500w-_-9SIA4CP1G...

  http://www.Amazon.com/solid-gear-series-ATX12V-SDGR-500BX/DP/B00FF7VEJE

  JCGood1984, welcome to the forum.

  The computer should take a standard ATX power supply unit (PSU).  I suggest to measure the existing PSU and compare measures in the links.  If the measurements are the same, it should fit.  I don't know anything about the brand, however.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• is it possible that a single screen will work with the slider and second focus mode

  Hello

  can you please tell me is it possible that a single screen will work with cursor mode and second focus mode.

  Thank you

  Hello

  I don't think that it is possible to change the mode of the development of your application outside of in the config.xml file.

  A custom extension may be able to do this, but I have not seen anyone this yet.

• Upgrading the video card and power supply, these will work with my system?

  Hello, I am wanting to update my graphics card as my current one is finally fall behind on current games, BF3 beta is a restless nighmare and BC2 must be smooth running low (ick). I was satisfied with the weaker graphics for now, but its time for an upgrade. In any case, I think I have my selected updates and I just want to confirm that they will work with my computer until I pull the trigger. My current equipment:

  HP p6180t

  http://h10025.www1.HP.com/ewfrf/wc/product?product=4010451&LC=en&cc=us&DLC=en&lang=en&tmp_track_link...

  Intel Core2 Quad 2.83 GHZ

  8.00 GB RAM DDR3

  Vista 64-bit

  Creative Sound Blaster X - Fi Audio Xrteme

  1.5 GB NVIDEA GeForce GT230 [DVI, HDMI, VGA]

  I plan on upgrading the graphics card on an Asus NVIDEA GeForce GTX 560 (Fermi)

  http://www.Newegg.com/product/product.aspx?item=N82E16814121446

  And the power of a passionate Corsair 850W 80 + CERT (I know this is perhaps an exaggeration, but I can update to motherboards in the future to run two SLI cards and do not want to upgrade again)

  http://www.Newegg.com/product/product.aspx?item=17-139-009&SortField=0&SummaryType=0&PageSize=10&PUR...

  I removed the side panel to check the dimensions of the new card and it looks like it fits. The only thing that could be a problem of release the cables SATA for the hard drive and hard drive because they are both plugged into the two slots, I don't think that the two superiors would be no problem at all. Depending on the thickness of the new card is also, it may be very close to the sound card that is spaced only a slit above the graphics card. I have another location available PCIe x 1 go back one level more that I should be able to plug the sound card in if there is no problem.

  My question is that these two will be compatible with my system? (physical limitations side)

  Also, can I change which SATA plug the hard drive and disc plug in, without having to reformat? Is it just unplug and plug in the new housing? (setting power off + unplugged of course) Basically passing SATA0 and SATA1, SATA2, and SATA3. Or do need to be filled in order? (0 then 1 then 2, etc...)

  Finally, If I can't move the sound of a standard card, do I need to do anything other than the physically move when the computer is turned off and unplugged?

  Any help is appreciated, thanks!

  John

  jkalbin,

  You have thought through all scenerios. Move the sound card does not any problems. The hard drive should stay in header SATA 0.

• PhotoShop CS6 will work with screen tactile Dell and Windows 10?

  I'm looking to replace my Dell laptop with a 15.6 laptop "series of Inspiron 5000, which has 16 GB RAM 1 TB HD, Intel i7 processor and an AMD Radeon R5 M335 4 GB DDR3 video card.  It is a touch screen with Windows 10.  In talking with Dell technical support, I was told that PhotoShop CS6 FONCTIONNERA NOT with Windows 10 not with the touchscreen even though technology Adobe said it will work with Windows 10 on its "required page.  Dell said that it works with WIndows 7.  I'm confused.  The Adobe forums seem to suggest that Photoshop CS6 will work, so with touch screen and WIndows 10, is there something in the specifications of laptop above Dell that suggests that I'm having a problem?  Will it be buggy?  PhotoShop CS6 will work only with a mouse and not the touch screen?  Is this a problem with the video card? I can't find enough information to feel confident about ordering this Dell laptop forums.  I can go to the 7000 series with a 4 GB NVIDIA® GeForce® GTX 960 M graphics, but I'm not a gamer.

  CS6 works fime on my Dell workstation.

  

• This external modem will work with Satellite L500-1XL, running Windows 7

  Hello

  When in Spain, I need to use the dialing up to the internet through Telefónica.
  I guess that the L500-1XL is not an internal modem?

  This external modem will work with the L500-1XL running Windows 7?

  Thank you very much in advance for your help.

  A

  Hello

  You re right Satellite L500 doesn t have an internal modem, so you need an external.

  I think you can buy every modem that is compatible with Vista. Alternative ask your favorite computer dealer or authorized service provider

  A friend got good experience with USRobotics 56K modem like this:
  [USRobotics 56K USB Faxmodem USR5637 | http://www.amazon.co.uk/USRobotics-56K-USB-Faxmodem-USR5637/dp/B0019LZCEI/ref=sr_1_1?ie=UTF8&s=electronics&qid=1269253039&sr = 8-1]

• I need to know how to remove the most recent version of Firefox. I JUST downloaded tonight and my computer does not have this edit bar little to work with, so I can download the reader good Adobe and my internet was screwed up ever since I downlo

  I need to know how to remove the most recent version of Firefox. I JUST downloaded tonight and my computer does not have this edit bar little to work with, so I can download the reader good Adobe and my internet was screwed up, since I downloaded the new version of Firefox. I want just the old version of this back because I can't download the Adobe stuff which is necessary to protect my computer against hackers apparently not. It would have been nice to know he had a problem with the new update of Firefox BEFORE I downloaded it. I have Vista, which is usually a problem with Adobe and Firefox. I don't seem to be able to run a lot of Adobe at all on my computer because of the Vista.

  This has happened

  Each time Firefox opened

  http://support.Mozilla.com/en-us/KB/installing+a+previous+version+of+Firefox

• All-in-one HP Officejet 7300/7400 series, it will work with Windows 7 and how to get the OCR software work?

  I have a HP Officejet 7300/7400 series all-in-one, it will work with Windows 7 and how to get the OCR software work?

  By installing complete software functionality of the HP cd or online installation and connection of the printer only when the installation says too much

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4062&LC=en&cc=UK&DLC=en&sw_lang=&product=391182#n193