Time loop writing file of Rio - please help

Hello world

I'm writing the data collected on the 32 channels of a module 9205 to memory on board a Rio-9074.  This isn't the final requirement of the application, but this is the first simple step.  Both the FPGA Vi and Vi of the host are attached to this post.

Writing to the file produced inside the while loop, so that the outside while segments of loop files from time to time (this segmentation is a requirement of our application).  I have attached a sample file of release in this post as well (the output file opens in wordpad).

In the output file, the second and the third column is a timestamp with fractional seconds.  The lead time is 5 Hz, but if you see the first lines in the output file, you will notice that it sometimes jumps an iteration of the loop - the timestamp, from 0.6 s to 1 s instead of s 0.6 to 0.8 s.  This occurs regularly throughout the file.  No idea if this due to a physical limitation of the hardware, or the clock, or if it's because of something in my program?  If you could please take a look at my program and help me optimize my screws or give me suggestions on why this delay occurs, I would really appreciate it.  Please let me know if you have other questions too, and I will answer them immediately.  Thank you!

P.S - Writing on an SD card on a 9802 using these programs also causes the same problem.

Good afternoon Derrick.

The following link describes the RT FIFO that I mentioned in my previous post.  It is the method you want to follow to get the data from your host RT to your PC so that you can save data to the PC.  It is a method of choice (when it is an option) because of the increased storage capacity of a PC (in general) and the requirement of transformation to write in the file on the host of the RT.

FIFO in real-time for deterministic data transfer screws

http://zone.NI.com/DevZone/CDA/tut/p/ID/3934

Alternatively, you can use something more similar to the example of "RT FIFO Communication.lvproj", found by searching FIFO in the Finder for example of NOR, to log on to the host of the RT.  Remember that you want to change this example; you don't want to write to the file in a timed loop because your hard drive / memory flash access is not deterministic.

Tags: NI Software

Similar Questions

  • write 1 d digital table in a binary file and start a new line or insert a separator for each loop writing file

    Hello:

    I'm fighting with digital table of 1 d writeing in a binary file and start a new line or insert a separator for each loop writing file. So for each loop, it runs, LABVIEW code will collect a table 1 d with 253 pieces of a spectrometer. When I write these tables in the binay file and the following stack just after the previous table (I used MATLAB read binary file). However whenever if there is missing data point, the entire table is shifted. So I would save that table 1-d to N - D array and N is how many times the loop executes.

    I'm not very familiar with how write binary IO files works? Can anyone help figure this? I tried to use the file position, but this feature is only for writing string to Bodet. But I really want to write 1 d digital table in N - D array. How can I do that.

    Thanks in advance

    lawsberry_pi wrote:

    So, how can I not do the addition of a length at the beginning of each entry? Is it possible to do?

    On top of the binary file write is a Boolean entry called ' Prepend/chain on size table (T) '.  It is default to TRUE.  Set it to false.

    Also, be aware that Matlab like Little Endian in LabVIEW by default Big Endian.  If you probably set your "endianness" on writing binary file as well.

  • When I download java comes up with error 25099 decompression of files has failed Please help

    WHEN I DOWNLOAD JAVA ERROR HAPPENS 25099 FILE DECOMPRESSION FAILED PLEASE HELP

    Hello

    You get this error message when you download java or installing it?

    Read the following article that may help you.
    Error: 25099 during Java installation
    http://www.Java.com/en/download/help/error_25099.XML

  • Java download the file is damaged, please help

    When I try to install the latest version of java, I get the message "Download file C:/Users/Derek/AppData/Locallow/Sun/Java/jre1.6.0_21/jre1.6.0_21-c-l.msi is corrupt" I tried redownloading the file again and I still get the same message, I'm out of ideas, please help.

    Thanks for your help, I tried your solution and unfortunately it did not work.  I went on the website and it wasn't much of a help either.  However, I found the solution to my problem!  I don't know if this would be the same for everyone, but when I went to download the latest version of Java once more on the site, I clicked "RUN" instead of "SAVE", after it's over, I installed the download and it was not the mistake bad guy who kept occurring. : D

  • Y580 NEW plant all the time? Can't do anything PLEASE HELP...

    I recently bought a Y580 for almost $1000 (something like 2 or 3 weeks). First of all, it worked perfectly, but yesterday I had to reboot using the button, because it crashed. Now, whenever I start it, either I get a black screen or it freezes when I open something like firefox, explore or just a folder. AND the worst thing is that Ctrl + Alt + Delete does not work so I can't open the Task Manager.

    I don't know if this can help, but once when I reboot the computer, I noticed a message saying something about Verifyhost.exe. And I don't know if it's a coincidence, but "Lenovo TouchZone" reappeared with these questions (I had deleted when I got my computer).

    I'm begging you help me please I am a student and I bought this computer because I needed a good for the College. first of all, I was happy about it but now I'm really angry and I don't know what to do. I can't contact the support cause I don't have a phone that's why I am posting this here. Please help me.

    Thank you

    I did a system restore and now everything works. Hope this helps those who have the same problem. I hope that this will never happen again - very bad experience.

  • Windows 7 DMP files included BSOD Please Help!

    For last 1-2 weeks have BSOD on my pc. I reinstalled Windows 7 Home Premium several times. A few days after each re - install Win 7 I start receving BSOD. I formatted my disk, partitions, etc. I just need to solve these BSOD. I've included below DMP and Dump WhoCrashed logs files. In these papers he suggests that my drivers could be the cause of crashes of theses. Let me know what is wrong in the comments below.

    Thank you

    Mike Read

    DMP files:
    https://onedrive.live.com/redir?RESID=40F0655702713F9A%21176

    Data sheet:
    Motherboard:
    -All Series, ASUS, ASUSTeK COMPUTER Inc., Z87.-k.
    CPU:
    -GenuineIntel Intel (r) Core i5 - 4670 K CPU @ 3.40 GHz Intel586
    Graphics card:
    -GeForce GTX 660 ti
    RAM:
    -8 GB company unknown.<-------Ran memtest="" 86="" on="" this="" ram,="" no="">
    Hardrives:
    -C = disk 128 GB SanDisk SSD drive
    -Drive(Gaming/storage) E = TOSHIBA 2 to 7200 RPM 64 MB cache

    WhoCrashed reports:

    Saturday, may 10, 2014 3:55:02 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-5023-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0xA (0xFFFFF6FCC8078408, 0xFFFFF80002CE089A, 0x2, 0x0)
    Error: IRQL_NOT_LESS_OR_EQUAL
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that Microsoft Windows or a driver in mode accessed kernel memory paged at DISPATCH_LEVEL level or above.
    This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 3:36:38 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-10405-01.dmp
    This was probably caused by the following module: ntfs.sys (Ntfs + 0 x 4211)
    Verification of error code: 0 x 24 (0xFFFFF8800B088068, 0xFFFFF8800B0878C0, 0x1904FB, 0xFFFFF80002DBEB05)
    Error: NTFS_FILE_SYSTEM
    file path: C:\Windows\system32\drivers\ntfs.sys
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT file system driver
    Bug control description: This indicates there is a problem in the NTFS file system.
    The accident took place in a standard Microsoft module. Your system configuration is perhaps incorrect. Maybe this problem is caused by another driver on your system which cannot be identified at this time.

    Saturday, may 10, 2014 3:33:49 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-28782-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Verification of error code: 0 x 34 (0x55F, 0xFFFFFFFFC0000420, 0 x 0 0 x 0)
    Error: CACHE_MANAGER
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that a problem has occurred in the file system cache manager.
    This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 3:29:40 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-5912-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0x1A (0xFFFFFA800339B0A0, 41790, 0 x 0 x 0, 0xFFFF)
    Error: MEMORY_MANAGEMENT
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that an error occurred serious memory management.
    This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 2:49:28 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-54974-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0x1A (0xFFFFFA80033A5C30, 41790, 0 x 0 x 0, 0xFFFF)
    Error: MEMORY_MANAGEMENT
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that an error occurred serious memory management.
    This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 2:40:44 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-8829-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0x1A (0xFFFFFA8003335C10, 41790, 0 x 0 x 0, 0xFFFF)
    Error: MEMORY_MANAGEMENT
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that an error occurred serious memory management.
    This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 2:37:22 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-5506-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0x3B (0xC0000005, 0xFFFFF80002ABDAC5, 0xFFFFF88009801810, 0x0)
    Error: SYSTEM_SERVICE_EXCEPTION
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.
    This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Saturday, may 10, 2014 2:32:51 AM GMT crashed your computer
    crash dump file: C:\Windows\Minidump\050914-7753-01.dmp
    This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
    Bugcheck code: 0x1A (0xFFFFFA8003389BE0, 41790, 0 x 0 x 0, 0xFFFF)
    Error: MEMORY_MANAGEMENT
    file path: C:\Windows\system32\ntoskrnl.exe
    product: Microsoft® Windows® Operating System
    company: Microsoft Corporation
    Description: NT Kernel System &
    Bug control description: This indicates that an error occurred serious memory management.
    This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
    The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

    Hello

    We have three controls compatible bug:

    MEMORY_MANAGEMENT (1A)

    This indicates that an error occurred serious memory management.

    Error checking 1A, {41790, fffffa800339b0a0, ffff, 0}

    - Parameter 1 of the bug check is 41790 indicating a page table was corrupted.

    3: kd > dt nt! _MMPFN fffffa800339b0a0
    + 0 x 000 u1:
    + 0 x 008-u2:
    + 0 x 010 PteAddress: 0xfffff6fb'40000050 _MMPTE
    + 0 x 010 VolatilePteAddress: 0xfffff6fb'40000050 empty
    + lock 0 x 010: 0n1073741904
    + 0 x 010 PteLong: 0xfffff6fb'40000050
    + 0 x 018 u3:
       + 0x01c UsedPageTableEntries: 0xffff
    + 0x01e VaType: 0 ''
    + 0x01f ViewCount: 0 "
    + 0 x 020 OriginalPte: _MMPTE
    + 0 x 020 AweReferenceCount: 0n128
    + 0 x 028 u4:

    UPTE has fallen below zero, which implies usually a driver caused the corruption (or faulty RAM memory).

    System_service_exception (3B)

    This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.

    This error has been linked to the excessive use of expanded memory and resulting from user mode graphics drivers enjambment and passing data incorrect of the kernel code.

    Bugcheck 3B, {c0000005, fffff80002abdac5, fffff88009801810, 0}

    3: kd > fffff80002abdac5 ln
    (fffff800'02abdac5)   nt! ExpInterlockedPopEntrySListFault16 |  (fffff800'02abdad0) nt! ExpInterlockedPopEntrySListEnd16

    The exception is produced in nt! ExpInterlockedPopEntrySListFault16.

    PAGE_FAULT_IN_NONPAGED_AREA (50)

    This indicates that invalid system memory was referenced.

    Bug control 0 x 50 usually occurs after the installation of a faulty hardware or installation failure of material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).

    Another common cause is a defective system service installation.

    Antivirus software can also trigger this error, as can a corrupted NTFS volume.

    ---------------------

    Run Memtest for NO LESS than ~ 8 going on (several hours):

    Memtest86 +:

    Download Memtest86 + here:

    http://www.memtest.org/

    Which should I download?

    You can either download the ISO pre-built you want to burn to a CD and then boot from the CD, or you can download the automatic installer of the USB. What this will do is format your USB drive, make a boot device and then install the necessary files. Both do the same job, it's just you that you choose, or you have available (be it CD or USB).

    Note that some older generation motherboards do not support USB boot, your only option is CD (or floppy if you really wanted to).

    How Memtest works:

    Memtest86 writes a series of test patterns for most of the addresses of memory, reads the written data and compares it to find errors.

    The default pass is 9 different tests, varying in the modes of access and test data. A tenth test, bland, is selectable in the menu. He wrote all the memory with zeros, then sleeps 90 minutes before checking to see if the bits have changed (perhaps because of refresh problems). This is repeated with all those for a total time of 3 hours by pass.

    Many chipsets can report RAM speed and timings by SPD (Serial Presence Detect) or EPP (Enhanced Performance Profiles), and some even support changing the expected memory speed. If the expected memory speed is overclockee, Memtest86 can test that memory is free of error with these faster settings.

    Some hardware is able to report the status of the "PAT" (PAT: active or PAT: disabled). This is a reference to the Intel performance acceleration technology; There may be the BIOS settings that affect this aspect of memory synchronization.

    This information, if it is available for the program, can be displayed via a menu option.

    Other questions, they can most likely be answered by reading this excellent guide here:

    http://Forum.canardpc.com/threads/28864-FAQ-please-read-before-posting

    Kind regards

    Patrick

  • BlackBerry Smartphones Blackberry 9800 - file access slow - Please HELP

    Hi all

    I'm new to the Forum of blackberry, but have used a bberry for years... I bought the new blackberry 9800 and love. But lately I had problems when access to the records of the unit, it's the situation.

    1. click on the Applications folder-> perfect 2-3 seconds to open-> go back

    2. click on the Applications folder-> open-> go back 2-3 seconds (repeat 3 - 4 times)

    3. click on the Applications folder-> 10-15 seconds to open - > back out (lock device or wait a minute or two)

    4. click on the Applications folder-> perfect 2-3 seconds to open the folder

    As you can see, you access the slowest records, he gets this is not limited to a few files but it also seems to slow down the entire system, I removed almost all of my applications on the phone always have this problem. I have a lot of free memory. So far, I have tried

    1 wipe device reinstall everything (problem returns after a day or two)

    (2 wipe device reload OS, reinstall any problem comes back after a day or two)

    3 will try tonight to reset the device, reinstall the OS, remove information from the user to the BES snack Server some strange permissions are pushed back, or a corruption of the database, reinstall only a small subset of applications that worked well on the blackberry 9700

    The only thing I can say is this started happening in installed an app from app world called "Server Monitor" I don't know if that's the problem...

    If anyone has any ideas please, I'll Sling that thing off the wall if it continues to be

    OS version 6.0 Bundle 695 (v6.0.0.246, platform 6.4.0.105)

    A battery Pull does not solve the problem...

    Thanks in advance

    Al.

    updated my blackberry to the latest version of the operating system and works perfectly now

  • Put error files, see photo, * please help *.

    Help, please

    When I try to put files on the server, it's fine the normal cycle, but as you can see on the image below in trasferd bysides the iteam top of the page.

    I don't not a FTP test and that said it connected, which has barely begun is there something that I'm going bad, or in the framework?

    Putfilesnottransferd.jpg

    Help, please

    Thank you very much

    123321Jack

    This shouldn't be happerning.

    Deleted is deleted.  The only reasons that you'd still see the pages when you navigate to a deleted file are.

    1. the server is cached pages - ask your host to see if this is true.

    2. your local browser is caching the pages - clear your local cache.  How to do it depends on your browser.

    If you have eliminated these two alternatives, then the pages are still there and my previous alternatives apply.

    Try this - create a new test page with unique content.  Save it and upload it to the same location from which you delete the files.  If he don't have a download?  You can now navigate to this page?

  • I had a DHL virus in my e-mail and now all my files are hidden, please help me

    can some help me to open them?

    Hello

    read the information at the bottom of the below link to the subject of some malware that hide your data files and the cure for it regarding

    Read article 17

    http://www.bleepingcomputer.com/virus-removal/remove-Windows-Recovery

    also follow the steps to remove given this malware

  • Function 'Internet time' will automatically refresh after reboot - please help

    I can't get the "Internet time" auto time update function system after restarting the computer in windows 7.  He should tell me when the next synchronization will happpen, but this isn't unless I do it manually by clicking on the button update.  Then he went after the reboot.

    Example: If I click on the clock at the bottom right of the screen and then select "Change date and time settings" and then click on the tab "Internet time" he says: "this computer is configured to synchronize automatically with"time.nist.gov.  Then on the next line, he says: "this computer is configured to synchronize automatically on a regular basis.   However, I checked that he never does that.  Or he tells me when he is going to do.

    To temporarily solve the problem, I click on the "Edit settings" button and then click on 'Update Now' and he said, "the clock has been properly synchronized with time.nist.gov on 15/03/2010 at 22:25" for example. I press OK.  So far so good.  Now the tab "Internet time" has a line that reads, "next synchronization 16/03/2010 at 02:25.  Which is 4 hours later, because the specialpollvalue registry variable is set for 4 hours.

    THIS IS WHAT I WANTED!  But the next time I restart the computer and check under the tab "Internet time", it comes back again tell me what is the next synchronization.  And the problem comes back to where it will not refresh automatically.   So reboot he kills.  All this works fine on another computer with XP.  But on a new, clean installation of windows 7 that is not.  Am I missing something?  Is there a setting I need to adjust so that it can stay active after restarting?

    Time Service Tools Windows and settings
    http://TechNet.Microsoft.com/en-us/library/cc773263 (WS.10) .aspx

    At the end of this document are details on recording the time of Service.

    Regarding-

    "SpecialPollInterval".
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient

    Version
    Windows XP, Windows Vista, Windows Server 2003 and Windows Server 2008

    This entry specifies the special poll interval in seconds for the manual counterparts. When the indicator SpecialInterval 0x1 is enabled, W32Time uses this interval instead of a poll interval determine the operating system. The default value on the domain members is 3 600. The default value on stand-alone clients and servers is 604 800. »

    Maybe you will get better results if you set the default value for domain members (3600), rather that I assume you have set for the 2400?  He may not know your adjustment because he runs into some unknown to me, another setting?  I guess you did not literally any value to read "4 hours" instead of 2400 decimals or whatever is the equivalent of Hex, did you leave in any commas in the value?  Sorry for asking that, please don't be offended by the question, but more strange things occur.

  • Please help with instalation cz Design Premium CS5 files

    I need a link to download the Czech of Adobe Design Premium CS5 version. I have the original software, keys, and the new book, but I do not have the instalation files there. Please help me.

    Available downloadable Setup files:

    • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
    • Acrobat: DC, XI, X | 9,8 | 9 standard | 8 standard
    • Captivate: 9 | 8 | 7 | 6 | 5.5, 5 | 1
    • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
    • Contribute: CS5 | CS4, CS3 | 3,2
    • FrameMaker: 12, 11, 10, 9, 8, 7.2
    • Lightroom: 6.1.1 . 6| 5.7.1| 5 | 4 | 3
    • Photoshop Elements: 14 | 13 | 12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
    • Premiere Elements: 14 | 13 | 12 | 11, 10 |8 mac | 7 mac

      Download and installation help links Adobe

      Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

    • Photoshop cs3 will open jeg, but files not raw for k3 pentax cameras.  Can you please help.

      Photoshop cs3 does not open raw (PEF) for cameras pentax k3 files, can you please help?

      Hi Davet,

      In order to open Pentax K-3 RAW files in Photoshop, you must at least Camera Raw 8.3 and above.

      However Photoshop CS3 will be unable to update until that Camera Raw 8.3

      Then I suggest you download DNG Converter, convert the PEF files to the DNG file format, and then use in Photoshop.

      Kind regards

      Tanuj

    • I have an error, missing wxmsw262u.dll and I don't know how to fix this error, please help.

      Try to find a solution to this problem and do not receive the case? I have read that I need to get the file off her recycle bin but that is empty. My PC Tools has been clean the tray for me is not that nice. I tried a recovery tool, but the file has disappeared for a long time to recover. I have the game Unreal Tournament 3 abd she needed a server crash bu patch that he would charge not because of the missing dll file. I can't play my game and I'm going to cry, I.; m 57 years and don't have a lot of time left in the world so please help me soon.

      Hello

      There is a long list of things to try to solve this problem

      you have to work your way through them

      http://pcsupport.about.com/od/findbyerrormessage/a/wxmsw262u-DLL-not-found-missing-error.htm

    • Problem with my VM and I can not run, Please HELP

      Hi all

      It's URGENT because I have problems with my virtual maching and I can't start it and all my work is out there and I don't have any other copy.

      the problem appears as follows:

      The machine virtual version 6.0.0 is installed on my laptop on drive e. I used for a long time and space on drive E is low. I wanted to copy visual studio 2010 from my laptop to the virtual machine when I got an error which has restarted the VM, but it didn't restart and always give me this error "could not open virtual machine: Machine WS2003\Windows Server 2003 Standard Edition.vmx E:\Virtual.» ' is not a configuration file valid virtual machine. I continued to try to find a solution. «I found the empty vmx file, so I tried to solve the problem of vmx but still I don't get this error»

      File not found: Windows Server 2003 Standard Edition - 000002.vmdk
      This file is required to power on this virtual machine.  If this file has been moved, please provide its new location. «or that the error "could not open the file" E:\Virtual WS2003\Windows Server 2003 Standard Edition.vmdk Machine": one of the disks in this virtual machine is already in use by a virtual machine or a snapshot." when I continue to pass the file vmdk.» Please help me, I need the data on the virtual computer.
      Please find the last vmwarelog (vmware.log) and the newspaper 3 days ago, when he was working fine (vmware - 2.log) and the vmx and vmdk file.
      Thanks in advance

      It seems that the file descriptor for the second snapshot vmdk was destroyed (0 bytes). Please find the file recreated in the attachment. I also corrected the .vmx file to point to the 000002.vmdk descriptor. To replace the files, make sure that VMware Workstation is closed or at least tab of the virtual machine is closed.

      Since there were errors in the vmware.log, this cannot solve all problems, but it must produce at least one new vmware.log which can then be used to troubleshoot further.

      André

    • Hi there I need help with my laptop my code is 55385917 please help

      • Hi there, I need help wit my computer hp pavilion laptop it starts just to show enter them administration or turn on password after 3 times the disable password are 55385917 Please HELP ME because THAT ALL MY WORK IS IT ON please

      Groove

      Try: 40083339

      Concerning

      Visruth

Maybe you are looking for