To connect to a host to EQL groups in separate without

Similar Questions

• Error code: 800ccc0e and the message "Unable to connect to the host server", when you set up Windows Mail to receive discussion group messages.

  I recently signed up for Windows Mail, Windows Vista Help. I have configured my Gmail OK account, but when I click TOOLS then Newsgroups I get the following error: unable to connect to the host server. When I click on show details, he said: Microsoft Community Server: msnews.microsoft.com Protocol: NNTP Port: 119 secure (SSL): 0 Code: 800ccc0e

  msnews. Microsoft.com has not existed for about three years now. MS close their news servers. You can still access newsgroups, but you will have to do with one another as eternal September or AIOE news server.
   
   

• EqualLogic used space after that rethinning differs in OS EQL group view

  Hello

  I have a PS4100 storage backend which serves a volume thin 1 TB LUN to a Windows 2008R2 server. The volume is formatted with NTFS 64 k block

  In windows, the Host Integration Toolkit is installed and if the option rethinning is provided regularly.

  Always after rethinning, the operating system displays 260 GB of free space on the volume, but the EQL Group Manager displays only 90 GB of free space.

  There is a difference of 170 GB between the two. Where's all overhead costs? 64 KB block size could generate some much overhead in the backend? and how could produce statistics or calculate overhead? The number of files on the volume is 5548. So normal usage for this volume are large files. (average 137 Mb/file)

  Can someone explain a little more later in this?

  Hello

  It will never (or very rarely) exactly match.   Partly because of the page size of 15 MB, that I mentioned earlier.  A single entry will keep a fully allocated page.  So until an entire page is released, it cannot be returned to space.

  Kind regards

  Don

• ' Could not connect: unable to connect to the host localhost: connection refused "on variuos orders

  On ESX 4.0.0 Update 1.

  When I run a command like "vim-cmd/hostsvc/hostsummary | "grep inMaintenanceMode" or vimsh - n - e/hostsvc/maintenance_mode_enter ' / 'vimsh - n - e
  "/ hostsvc/maintenance_mode_exit" all returned the same error message ' could not connect: unable to connect to the host localhost: connection refused.

  I checked the checked the file /etc/resolv.conf Bed & Breakfast.

  I am able to ssh on the server as well as the use of WinSCP without any problem.

  I can connect with the VI Client also without problem.

  Any ideas?

  The problem has been resolved.

  The fix:

  =====

  # vimsh-e - n/hostsvc/hostsummary | grep inMaintenanceMode

  Using the libcrypto, version 90809F

  inMaintenanceMode = false,

  # vim-cmd/hostsvc/hostsummary | grep inMaintenanceMode

  inMaintenanceMode = false,

  Rationality for the problem is these commands (vim - FCM or vimsh) were unable to communicate due to lack of xinetd process.

  # ps - ef | grep-i xinet

  root 11527 25978 0 04:30 pts/0 00:00:00 grep-i xinet

  # service xinetd restart

  #

  # Service xinetd status

  #

  # service xinetd start

  # Service xinetd status

  # /etc/init.d/xinetd ls

  /etc/init.d/xinetd

  / * But NETWORK seems to be normal on the server * /.

  # cat /etc/resolv.conf

  nameserver 172.26.6.21

  nameserver 172.25.6.51

  # ifconfig

  Lo encap:Local Loopback link

  INET addr:127.0.0.1 mask: 255.0.0.0

  RACE of LOOPING 16436 Metric: 1

  Dropped packets: 6053620 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 6053620 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:0

  RX bytes: 2021352939 (1.8 GiB) TX bytes: 2021352939 (1.8 GiB)

  ppp0 link encap:Point - to-Point Protocol

  INET-addr:164.152.87.72 P - t - P:164.152.87.64 mask: 255.255.255.255

  Up POINTOPOINT RUNNING NOARP MULTICAST metric MTU:1500: 1

  Fall of RX packets: 208 errors: 2:0 overruns: 0 frame: 0

  Dropped packets TX: 205 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:3

  RX bytes: 18165 (17.7 KiB) TX bytes: 22314 (21.7 KiB)

  vmnic100200 Link encap HWaddr 00: 1B: 21:6 A: C9:C4

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 1383869 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 1382815 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 90351869 (86.1 MiB) TX bytes: 92106912 (87.8 MiB)

  Interruption: 97

  vmnic100201 Link encap HWaddr 00: 1B: 21:6 A: C9:C5

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 24239456 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 23905751 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 2078777971 (1.9 GiB) TX bytes: 2226266024 (2.0 GiB)

  Interruption: 113

  vmnic100600 Link encap HWaddr 00:25:5 C: 2: 75:30

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 13076343 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 5226061 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 1292112365 (1.2 GiB) TX bytes: 1224021381 (1.1 GiB)

  Interruption: 129

  vmnic100601 Link encap HWaddr 00:25:5 C: 2: 75:31

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 819469 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 770101 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 56287946 (53.6 MiB) TX bytes: 52499576 (50.0 MiB)

  Interruption: 137

  vmnic110200 Link encap HWaddr 00: 1B: 21:6 A: CA:44

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 1774795 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 1681079 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 142435399 (135.8 MiB) TX bytes: 135079293 (128.8 MiB)

  Interruption: 145

  vmnic110201 Link encap HWaddr 00: 1B: 21:6 A: CA:45

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 21079616 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 20688606 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 1859632344 (1.7 GiB) TX bytes: 1852761835 (1.7 GiB)

  Interruption: 161

  vmnic110600 Link encap HWaddr 00:25:5 C: 2: 75:32

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 39205375 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 21339531 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 32420064542 (30.1 GiB) TX bytes: 3709579479 (3.4 GiB)

  Interruption: 177

  vmnic110601 Link encap HWaddr 00:25:5 C: 2: 75:33

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 2922150 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 2110634 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 398811808 (380.3 MiB) TX bytes: 245899848 (234.5 MiB)

  Interruption: 185

  vswif0 Link encap HWaddr 00:50:56:41:76:EB

  INET addr:172.26.6.13 Bcast:172.26.6.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 109779 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 23715 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 10137604 (9,6 MiB) TX bytes: 21716347 (20.7 MiB)

  vswif1 Link encap HWaddr 00:50:56:40:30:F7

  INET addr:172.26.7.11 Bcast:172.26.7.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 36515 errors: 0:0 overruns: 0 frame: 0

  Dropped TX packets: 4 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 3702390 (3,5 Mio) TX bytes: 168 (168,0 b)

  vswif2 Link encap HWaddr 00:50:56:4 A: DF:1 B

  INET addr:172.26.8.11 Bcast:172.26.8.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 20525 errors: 0:0 overruns: 0 frame: 0

  Dropped packets TX: 6 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 2742990 (2.6 MiB) TX bytes: 252 (252.0 b)

  vswif3 Link encap HWaddr 00:50:56:4E:1E:24

  INET addr:172.26.9.12 Bcast:172.26.9.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 26408 errors: 0:0 overruns: 0 frame: 0

  Dropped TX packets: 4 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 3095970 (2.9 MiB) TX bytes: 168 (168,0 b)

  # / opt/ft/bin/ftsmaint lsVnd

  Virtual network device (VND) groups

  ===================================

  Status of group name

  --------------------------

  vSwitch0 ONLINE

  vSwitch1 ONLINE

  vSwitch2 ONLINE

  vSwitch3 ONLINE

  Members of the Group of VND

  =================

  Link Group Name status Interface link state speed

  --------------------------------------------------------------------------

  vmnic100200 vSwitch2 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100201 vSwitch3 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100600 vSwitch0 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic100601 vSwitch1 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110200 vSwitch2 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110201 vSwitch3 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110600 vSwitch0 DUPLEX UP LINK 1000 Mb/s-FD

  vmnic110601 vSwitch1 DUPLEX UP LINK

  1000 mb/s-FD

  / * Further consideration on the problem of starting XINETD * /.

  Further examination shows that the xinetd is unable to start because he believed NETWORK unavailable.

  Starting xinetd uses the contents of the sysconfig file where there was an entry incorrect "NETWORKINcesv = yes". We have corrected this entry and restarted xinetd process.

  After this correction, xinetd is restarted, the system seems to be normal.

  # cat sysconfig

  NETWORKINcesv = yes

  HOSTNAME = Server.test .net

  GATEWAY = 172.26.6.1

  IPV6_AUTOCONF = no

  NETWORKING_IPV6 = no

  #

  # cat sysconfig

  Networking = yes

  HOSTNAME = Server.test .net

  GATEWAY = 172.26.6.1

  IPV6_AUTOCONF = no

  NETWORKING_IPV6 = no

  # ps - ef | grep-i xinet

  root 27977 25978 0 04:41 pts/0 00:00:00 grep-i xinet

  # service xinetd start

  [From xinetd: OK]

  # ps - ef | grep-i xinet

  root 28119 1 0 04:41?        00:00:00 xinetd - stayalive - pidfile /var/run/xinetd.pid

  root 28239 25978 0 04:42 pts/0 00:00:00 grep-i xinet

  #

  # service xinetd restart

  [Judgment of xinetd: OK]

  [From xinetd: OK]

  # vim-cmd/hostsvc/hostsummary | grep inMaintenanceMode

  inMaintenanceMode = false,

  # vimsh-e - n/hostsvc/hostsummary | grep inMaintenanceMode

  Using the libcrypto, version 90809F

  inMaintenanceMode = false,

  #

• New VM vCenter and need to connect to a host ESX1 4.1.

  Hi all

  I'm in a difficult situation not in my enterprize environment, but someho I am very confused after a few hours by train.

  Currently I have an ESXi host 4.1 with some virtual machines on it. One of these virtual machines is the vCenter server that had been upgraded to version 5.1 a few months ago. The vCenter Server runs on a virtual Windows Server 2003 64-bit machine.

  Two days ago, I decided to upgrade the vCenter 5.1 to 5.5, but unfortunately the version 5.5 does not work on a Win 2003 server. So I installed a new virtual machine with Windows server 2008 R2 and the plan is either to migrate the new everything from the former vCenter, or simply connect to the new server vCenter with the host (I have not run any complicated environment, I have only 5-6 virtual machines and the only thing that I would need the former vcenter is a few shots but I don't like if I don't get them).

  First, I installed the new vCenter (5.5) and I connected to the host. I logged in as [email protected] , and I could see the server vCenter there. I've added my account domain in the Administrators group and the VCOAdministrators group, but when I connect with my domain account that I do not see any server of vCeter it.

  Now, what I want to ask you is: you have read above I want to do. What would you do if you were me?

  Thank you for all your answers.

  Sign in using the account [email protected] and check the permissions on the server vCenter Server object in the inventory. Make sure that the required domain user (or better yet a domain group) has the appropriate permissions to the object and the objects below it.

  Adding an account to the Administrators group internal grant permissions required to manage the server vCenter Server itself, but does not apply to the inventory.

  André

• On sending a message, the server sent a wrong message: #4.4.5. too many connections to the host

  On sending a message, an error has occurred "the mail server has sent a wrong message: #4.4.5 too many connections to this host..."
  The mail is displayed as sent in envoys, but is not received by the recipient. On sending several messages to test myself this fault seems to be intermittent.

  Hmm did you get mail outbound scanning performed by an anti virus program? Turn the power off.

  Have the e-mail account on your phone? try turning off your phone.

  Is the IMAP or POP account?

• When I try to connect directly in multiplayer FSX without gamespy, every time I get an error message saying: unable to create the connection to the host.

  When I try to connect directly in multiplayer FSX without gamespy, every time I get an error message saying: unable to create the connection to the host.

  I need help
  Kind regards

  Thank you very much!

  To host successfully a FSX session what follows is the key enabling

  my client (s) to join my host FSX session!

  "Players Maximum (for a shared together plane 2) leave the locations reserved for friends to 0 set."

  6122 6112 UDP port translation FSX multiplayer traffic of my remote 2 wire gateway to my router Linksys Wireless N DMZ to access game FSX host...

  Only a single router in my configuration of the DMZ, the external network to the router,

  in this case, the 2 wires, had defined port forwarding.

  Am now enjoying Gamespy (R.I.P.) FSX free hosting for my MP FSX sessions via direct connection.

  5 high to the author!

• The same day as my expired Norton my internet connection icon says... unknown internet connection. The dependency service or group was able to start.

  the dependency of the orgroup faaied to start service unknown Internet connection.

  The same day as my expired Norton my internet connection icon says... unknown internet connection. The dependency service or group was able to start. I tried all the suggestions on this page. Can't even find the virus that the internet not connected. My livebox is grateful for the laptop please help

  Hello

  ·         You will remember to do recent changes on the computer before this problem?

  ·         Is the question only for the icon network did you try to open a Web page and check?

  ·         What suggestions do you have tried?

  ·         What is the exact error message?

  ·         Have you tried all the steps from the link?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/connection-status-unknown-the-dependency-service/92203623-b6d5-4301-8c79-00210abbcdd4

  I suggest you follow the steps mentioned below:

  Method 1:

  Follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/943996

  Registry warning:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2:

  If the previous step fails, follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/936211

  Method 3:

  If the previous step fails, reset WinSock and check if the problem persists:

  http://support.Microsoft.com/kb/811259

  Registry warning:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 4:

  Temporarily disable the norton software (and any other security software) and the firewall on the computer as a test and check if this solves the problem follow the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program.

  Note: make sure that you enable the antivirus software, other security and firewall programs.

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• Error 1068: Unknown connection status: the service dependency or groups could start

  Hi all

  I ave a problem with Vista service pack 2 running on Sony viao with the network. I have access to the internet, but my connection icon has a red X on it with the message "unknown connection status: the dependency service or group could not start". I did my homework to browse all the threads and have performed all of THE following conditions, but the problem persists.

  1. in the course of execution sys check through sfc/scannow

  2. reset TCP/IP through 1. netsh winsock reset 2. netsh int ip reset

  3. verification of all services such as the services in the list of networks and knowledge of network locations.

  However the problem persists. I cannot forget to mention that the list of Network Services and network location awareness not start I get the same error when I try to start them. I checked all the services above is dependent on and they are started and set to automatic.

  Is there anything else I can do to solve this problem other than the system of recovery or reinstallation? I have some stuff on my laptop that even if I save them I have given will be lost. for example the accounting software with its data, software for which I don't have the disk to re - install and the data in them cannot be saved on a server running. To make the story short, I really want to avoid recovery on the option of resettlement

  As I said, I have access to the internet, but the mere fact that this problem is there, its that bothers me and I don't want to run bigger problems later

  Any help would be greatly appreciated

  Thanks in advance

  Hi IMOMDS,

  1. don't you make changes before the show?
  2. have you checked if the network connections and support TCP/IP NetBIOS services are started?

  Try these steps and check the result.
  Step 1: Virus scanner online
  a. visit http://onecare.live.com/site/en-us/center/whatsnew.htm
  b. click Full Service scan and complete the scan.
  c. check the difference.

  Note: Use your favorite security software to search for viruses or malware on the computer and remove it.

  Step 2: If the problem persists, restore the computer to an earlier time when it was working fine
  a. see what is system restore?
  b. Once you have restored the computer, check if the problem persists.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• vCenter Server displays the error message: unable to connect to the host

  vCenter Server displays the error message: unable to connect to the host

  Symptoms

  • vCenter Server cannot connect to a host when you perform operations such as:

  •

  o Storage vMotion

  o cold migration

  o cloning a virtual machine

  o the model deployment

  • Newspapers vpxd that contains an entry similar to:

  [2009-06-04 19:27:16.326 error "App" 4444] [VpxdInvtHost] IP address change for 10.223.122.143 to 10.223.127.197 unhandled, verification of the SSL certificate is not enabled.

  • You see errors similar to:

  Unable to connect to the host o

  o [2009-06-04 19:27:09.952 'Libs' 3902384 WARNING] [NFC ERROR] NfcNewAuthdConnectionEx: unable to connect to peer (numRetries = 2). Error: Unable to connect to the host 10.223.122.143: connection timed out

  • vCenter Server shows the VMS as being disconnected then connected.

  Hello

  Resolution

  Cause

  This problem can occur if an ESX host's IP address is changed while being managed by vCenter Server.

  Check the cause

  To check the cause of the problem:

  1. Log in as root to the ESX host using a SSH client.
  1. In the file etc/opt/vmware/vpxa/vpxa.cfg, find the IP address of the host. The entry looks like:

     
     10.21.48.121
     

     Note: for more information about editing the files, see installation in VMware ESX configuration files (1017022).

  Troubleshooting

  If the IP address is incorrect, perform the following steps in order. If the operation does not resolve the problem, continue to the next step. Don't skip a step.

  1. Disconnect and then reconnect the host:
  1. Right click on the ESX host in vCenter Server and click Disconnect.
  1. Reconnect the ESX host in vCenter Server.
  1. Restart the VirtualCenter agent on the ESX host:
  1. Stop the service of vpxa with the command:

     # service vmware-vpxa stop

  1. Open the /etc/opt/vmware/vpxa/vpxa.cfg file in a text editor and correct the IP address of the ESX host.
  1. Start the service of vpxa with the command:

     # service vmware-vpxa start

     Note: for VMware ESXi, you may have to restart all the management agents. For more information, see restart the agents on an ESX or ESXi Server (1003490) management .

  1. Rebuild the VirtualCenter agent on the ESX host configuration file:

     Attention: this step removes all the Statistics counters historical host and the virtual machine. If VMware ESX host is running in virtual machines that starts in a permitted CVS environment, you maybe won't be able to add the host without stopping the virtual machines first.

  1. Right click on the ESX host in vCenter Server and click Disconnect.
  1. Remove the ESX host disconnected from vCenter Server.
  1. Backup the file vpxa.cfg with the command:

     # mv /etc/opt/vmware/vpxa/vpxa.cfg /etc/opt/vmware/vpxa/vpxa.oldcfg

  1. Add the ESX host disconnected to the server vCenter inventory.
  1. Run the following command to view the contents of /etc/opt/vmware/vpxa/vpxa.cfg and confirm that the host IP address is correct:

     # cat /etc/opt/vmware/vpxa/vpxa.cfg

• When I try to connect to my remote server the message "an ftp error occurred - cannot establish a connection to the host." How can I get the server to which to connect with dreamweaver?

  When I try to connect to my remote server the message "an ftp error occurred - cannot establish a connection to the host." How can I get the server to which to connect with dreamweaver?

  After spending most of the day on this I found that my password required to upgrade... so two of my sites are now meet Dreamweaver. And the other will be taken care by the owner of the Web site. Thank you, Nancy!

  gay

• Failed to connect to client host vsphere and Vcenter also esxi.

  Hi all

  I am trying to connect to the ESXi 5 of vsphere client host. I get the error message:

  vSphere client cannot connect to < ip > an unknown connection error has occurred. (The request has failed because the remote server has taken too long to respond. (L'opération a expirer)).

  and of VCENTR I am trying to add this host. I get the error. Of"request timed out".

  I can connect to the shell of ESXi and restart the vpxa services and spend. I can ping to esi IP host. but just cannot connect to it.

  earlier, he the host showed as disconnected in Vcenter. I tried to plug it failed. so I took it off I think can re add back. It did not work.

  I can just connect to client as esx host.

  kindly advice.

  Thank you

  Hello

  I am able to connect now.

  I noticed as I said previously, unable to connect to the localhost error when running esxcli. Unable to connect using the vsphere client. Unable to connect using VCenter.

  So I started to dig that's wrong with the OS esxi. and began running a few commands information esxcfg etc file system use of space, inode inconsistency, a few other commands such vdh, df to check the file system.  . and but has not changed anything. network configuration is correct.

  in these I run services.sh reboot, restart vpxa, pass reboot, restart host, check the logs, vmkernel, vpxa newspapers spend., check the date and time of the host.  I couldnot Firewall check since esxcli did not work. I haven't checked listed above step on the SSO.

  If you type esx and double tab, you will see many orders. I started testing on these orders.  so esxcli was a single command I tried later. It worked all of a sudden.

  Once esxcli has started working, I checked vsphere client to connect to esx host that it worked. then I was able to connect in Vcenter also.

  Thank you for your support

  -Caroline

  UNITED ARAB EMIRATES

• Unable to connect to guest host AD

  I have a Windows 2008 R2 server that is running VMWare Workstation 11. One of the virtual machines is a Windows 2012 R2 domain controller. I can connect to other virtual machines to the domain without any problem. However, I am unable to connect to the host to the domain.

  When I try to connect, I get the following error.

  A domain controller Active Directory (AD DC) for the domain 'corp.mydomain.com' could not be contacted. Ensure that the domain name is typed correctly.

  I enclose the error details. For some reason I couldn't copy and paste in this editor.

  You need to host somehow aware of the "corp.mydomain.com" field in order to be able to join the domain. What can work is to add the IP address of the domain controller (assuming that the DC acts as a DNS server) as an extra entry to the list of DNS servers from the host (such as the first condition in the list).

  How you have configured other systems that joined you to the domain?

  André

• Is there a way to get the list of hosts and its groups of belonging to the vCenter folder level in 5.5 web vsphere client plugin development?

  Hello

  I need to get the list of all hosts and its groups of belonging to the vcenter folder level.

  1. I created a view giving the extension point: vsphere.core.folder.monitorViews.

  2. After this step, I wrote the constraint as in my class of mediator,

  var ListConstraint:Constraint =

  QuerySpecUtil.createConstraintForRelationship ( _contextObject, 'childEntity');

  I was expecting a list of all child entities such as hosts, dc, cluster... But I have only the immediate child object which is only the Datacenter as my result.

  Is it possible to get all hosts and vCenter folder level Clusters because I need the entire list to vCenter (highest level).

  Other info:
  

  Object file has only two properties:

  1 childEntity - list of entities

  2 childType in-kind folder ('Virtual Machine', 'Data center'...)

  Is it possible to write a constraint specifying which list of childEntities I need using childType in.

  Example: Make Me childEntities that has a 'Host' and 'Cluster' childType but childType in doesn't have these two types.

  In addition, at this level, I could see the 'Associated objects' tab which has all the information I need, such as Clusters and Cluster tab hosts and host tab respectively.

  So, I think its possible to get this list to vCenter folder level.

  I have attached a screenshot representing the need. Kindly ignore the Conventions of naming in there since I edited the example comes with the sdk program.

  
  

  Query:

  1. How can I get the host and Cluster (table of relationship) list to vCenter folder level or even at the level of the vise.global.view?

  2. once I get this list, is it possible for me to manipulate that list and send the new list to IU?

  3. is there another way to do the same thing without the help of model classes and mediator?
  

  
  

  Pointers to this will be very useful.
  

  It is not possible to obtain all hosts a folder specific vCenter from a single query Data Manager.  You need to get the list of centers of data first and then get a list of data center hosts.

  It is best to make these repeated requests to the java level and return only the list that you want to the user interface.

  You can get all the objects in the host of the system with a simple query using a constraint with targetType = 'HostSystem', but you will need to eliminate those from other vCenter servers.  See how this chassis example queries all hosts the Java later in the getHosts() method: samples/chassis-app/chassisRackVSphere-service/src/main/java/com/vmware/samples/chassisRackVSphere/ChassisRackVSphereDataAdapter.java

  Another option is to use the vSphere Web Services SDK to browse vCenter. See the vSphere management forum for help on these APIs.  See this plugin of the sample using this SDK

  samples/vsphereviews/vsphere-wssdk-provider/src/main/java/com/vmware/samples/wssdkprovider/VmDataProviderImpl.java

• Interruption of the connection to the host ESXi 5.1

  I did some tests on one of our hosts in preparation for the essential moving to Essentials more when I noticed that most of the vmnic reported only 100 MB Full Duplex connection speeds.  We have a Dell R515 with 2 cards Broadcom NetXtreme II BCM 5709, all set to auto negotiate, so I thought I'd try and force one vmnic to communicate to 1000Mb Full Duplex.  This had quite disastrous consequences resulting in a lack of connectivity to the host.  VCentre host is reported as Disconncted and if I try to connect directly to the host I get a type error "unable to connect".

  Fortunately the virtual machine is still ongoing so I just need to get that host online.  SSH is turned off so I can't chew on the host, if I don't have physical access to it if necessary.

  The management network is running on vmnic8, which is embedded Broadcom BCM5716, while I just changed vmnic6 on one of the Broadcom BCM5709 map, then why I lose o management network connection, I'm a little confused, any help appreciated.

  See you soon

  Dean

  Just follow the steps described in the section "setting the speed and duplex of the NIC in ESX/ESXi host at the service console. In step 1, you will find links to find out how to enable Shell access. Basically you log in to the DCUI to allow Shell access in the "Troubleshooting Options" menu and press ALT - F1 to switch to the console. After the connection, use esxcli nic network list for an overview of installed vmnic network nic esxcli get vmnic8-n to display the settings vmnic8 and esxcli network nic address-n vmnic8-a to set the speed and duplex automatic. For more information about the command, see http://pubs.vmware.com/vsphere-50/index.jsp#com.vmware.vcli.ref.doc_50/esxcli_network.html

  André