Total number of concurrent VPN connections.

Hey guys,.

Is it possible to display or not even connect to the total number of simultaneous in one month vpn connection?

THX

On the SAA, you can enter the command "Show vpn-sessiondb", it shows the info.

Demo - asa vpn-sessiondb # HS

Summary of the current Session

Sessions:

Active principles: Cumulative: simultaneous peak: inactive

SSL VPN : 0 : 145 : 7

Clientless only: 0: 30: 2

Client: 0: 0: 3: 115

E-mail Proxy: 0: 0: 0

IPsec LAN-to-LAN: 0: 0: 0

IPsec remote access: 0: 0: 0

VPN load balancing: 0: 0: 0

Totals: 0: 145

Information about the license:

IPsec: 750 configured: 750 Active: 0 load: 0%

SSL VPN: 50 configured: 50 Active: 0 load: 0%

Active principles: Cumulative: simultaneous peak

IPsec : 0 : 0 : 0

SSL VPN : 0 : 145 : 7

AnyConnect Mobile: 61: 61: 61

Linksys Phone: 0: 0: 0

Totals: 0: 145

I'm sure that there are much better alternatives such as Cisco ACS including the quality of the production.

But I have recently installed Microsoft IAS on my Windows 2003 server and then configured accounting for my VPN group policy. I then used a free 'IAS log viewer"software which is able to provide the use of my VPN.

See the article below for configuring Microsoft IAS on Win2k3:

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a0080094700.shtml

The whole process took me less than an hour. Nice report generated by the IAS log viewer.

Thank you

Kiran

Tags: Cisco Security

Similar Questions

Where you control the number of concurrent ftp connections in Dw cc v 13?

My server keeps me blocking because dw made too many connections then I can not any work done and I have to go to bother my hosting company.

If you are using Windows, you can try dreamweaver CS6 FTP problems

Number of tunnel VPN LRT224

Hello!

I trying to get the LRT224 and need to understand something before you buy it:

Manual user said it supports 50 VPN tunnels, but in the demo of the user Web interface, I can see PPTP 45 + 5 + 5 OpenVPN EasyLink - how these add up?

In addition, these numbers limit the simultaneous number of tunnels or VPN accounts? For example can I have 10 accounts Easy Link (Open VPN) created and use only 3 of them at the same time, for example?

Thank you very much!

Hello, Amalakhov! These are the VPN router features:

-50 via IPsec Site to Site tunnels
-5 (compatible with OpenVPN) SSL tunnels
-5 PPTP tunnels
-IPsec 110 Mbps throughput
-12 Mbps SSL throughput

The maximum number of concurrent VPN connections through the router depends on the flow of IPSec. Your connection will be sacrificed if you would connect more than 5 tunnels at the same time.

Number of concurrent connections to remote desktop on Windows Server 2008 and 2012

Dear,

Can someone help me with what is the maximum number of concurrent connections on Windows Server 2008 (Standard & Enterprise) and Windows Server 2012 as well.

Kind regards

Hello

Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

See you soon.

Know the total number of connection created in AM Pool?
Hi all
I use 11.1.2.0.0(11gR2) Jdeveloper.

We use 3 Modules of Application within our application.
How to find the total number of connections created in the pool of the AOS?
Any option in weblogic for this or by programatically means how?.

Thank you
Vass Lee
Try this
http://spotlearning.WordPress.com/2011/07/10/get-application-module-pool-statistics/

VPN connection question

In my workplace, there are two networks is the local LAN that connect other computers to the internet and the wireless network which my computer connect to and is directly to the internet, my question is that is it possible to connect to the LAN over the internet using the connection V P N if yes how? Please help me because whenever I want to read my emails, I have to put the UTP cable which will be sometimes annoying.
Please indicate all the measures that are needed to establish the VPN connection.

Ask it professionals about your place of work. They know what is possible and what is not.

Where I work, there is an available VPN that allows connections to the LAN from outside work. If I use a laptop computer provided by the company, access the LAN just as if I'm at work. If I use my PC, I get a link that allows me to access a limited number of resources, such as the email of the company. I can, however, DRC to my desktop at work PC and can get access to the local network.

Total number of pages printed on printer e-all-in-one-hp officejet 6700 premium do not match

Printer model: hp officejet 6700 premium e-all-in-one

OS: windows xp, service pack 3

Method of connection: network

Description of the problem: number of page do not match

If I double click on the "hp officejet 6700" icon on my desktop.

Then click on "view the ink level.

Then click on the reports of the device"" tab.

Then click on "check printing.

The report provides: Total number of printed Pages 8159

If I double click on the "hp officejet 6700" icon on my desktop.

Then click on "view the ink level.

Then click on the "devices" tab

Then click on "printer ews home page."

Then click on the 'Tools' tab, I see:

Total number of pages

6725

Difference = 8159-6725 = 1434

Can someone tell me why these numbers are different? They represent different totals?

MelanieHello and welcome to the Forums of HP, I hope you enjoy your experience!

I see that you have questions about your number of pages. I would like to help.

The built-in web server does not account for pages printed not across the network. The number of printer pages all the elements. 1434 pages were not printed through the network, therefore, not counted in the SAP.

Please let me know if you have any questions. Thanks for posting on the HP Forums!

The VPN client VPN connection behind other PIX PIX

I have the following problem:

I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

194.x.x.x is our customer s address IP PIX

I understand that somewhere access list is missing, but I can not understand.

Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

Can you please help me?

Thank you in advan

The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

I've cut and pasted here for you to read, I think that the problem mentioned below:

Question:

Hi Glenn,.

Following is possible?

I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

Thank you very much for any help provided in advance.

Response from Glenn:

First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

fixup protocol esp-ike

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

ISAKMP nat-traversal

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

Hope that helps.

RV180 VPN connects and allows you to browse the files, but falls when opening a file.

Last week, we received our 300Mbps fiber connection. We bought the RV180 due to its high performance, and he manages the speed perfectly.

However, when you set up VPN, I encountered a strange problem.

Establishing a QuickVpn or PPTP is simple and connection is no problem. But I'll be fine. I can communicate with QuickVpn or PPTP and find a NAS or PC directory structure, but when I try to open a file the VPC connection drops.

I activate the remote management.
I can ping google.com f-l 1472 without fragmentation, so a WAN MTU of 1500 should be ok.
I have tried disabling attack prevention firewall.

I have install the following experience: the firmware update (1.0.2.6), restore the default settings.

Set up the RV180 as follows:

IPv4 WAN (Internet)

------------------------------------------------------------------

Internet connection type: Automatic Configuration - DHCP

DNS Server Source: Get dynamically for ISP

MAC address of the router: use the default address

IPv4 LAN (local area network)

------------------------------------------------------------------

Host name: RV180

IP address: 192.168.75.1

Subnet mask: 255.255.255.0

Mode DHCP: DHCP Server

Domain name: LCDVT

From the IP address: 192.168.75.100

End IP address: 192.168.75.254

Rental time: 24

DNS Proxy: enable

Preventing attacks

------------------------------------------------------------------

WAN (Internet) security controls

Meet Ping on WAN (Internet): disabled

Stealth mode: disabled

Floods: disabled

LAN (local area network) security controls

Block UDP Flood: disabled

Parameters of the ICSA

Block the anonymous ICMP Messages: disabled

Block fragmented packets: disabled

Block multicast packets: disabled

VPN users

------------------------------------------------------------------

PPTP server: enabled

From the IP address: 192.168.75.50

End IP address: 192.168.75.99

Table setting VPN Client:

---------------------------

No: 1

Enabled: enabled

Username: lcdvt

Password: *.

Allow the user to change the password: NA

Protocol: PPTP

Web access

------------------------------------------------------------------

Access on the LAN of HTTPS Web Interface: enabled

Remote management: enabled

Type of access: IP range

Start of range: 192.168.75.1

End of series: 192.168.75.254

Port number: 443

Remote SNMP: disabled

The rest of the menu options are, except for logging policies where I have everything turned on by default.

In this experiment, I connect from a remote location, start navigating among directories of the drive without any problems and then open a file, after which the VPN connection falls (or some process breaks down). After the transfer of a few 100 KB blocks the VPN connection.

Error logs

------------------------------------------------------------------

Thu Mar 20 00:39:18 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

Thu Mar 20 00:39:25 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

Thu Mar 20 00:39:32 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:40:58 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

Thu Mar 20 00:41:10 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

Thu Mar 20 00:41:19 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Warning logs

------------------------------------------------------------------

Thu Mar 20 00:39:13 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

Thu Mar 20 00:40:54 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

Sat 1 Jan 01:02:43 2011 (GMT + 0100) [rv180] [Kernel] [KERNEL] [23.090000] /home/aruns/rv180w/updated_dec19_final/beta-v1/rv180w-common/comps/gpl/ipset/src/ipset/kernel/ip_set.c: ip_set_create: no type set 'nethash', 'setPublicNet' has not created value

What I am doing wrong? Or the device?

I am interested in what the solution to these problems. Research on get a rv180...

First car of Huntsville and bike e-magazine: www.huntsvillecarscene.com

ASA5505 - remove VPN connections

Hey all, have a simple question.

the following page indicates it can handle up to 10 connections vpn with a basic license. This means that we can configure only 10 credentials of the vpn user/pass? or, we can create, for example 50 accounts user/pass, but only 10 can remote in at the same time.

http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

Thanks for the help.

-robert

Robert,

That's right... 10 ways to connections VPN is a vpn connections simultaneous maximum with base... license you can create as many users in the local database asa but only 10 RA VPN client sessions can be established, however, that this column includes also the VPN L2L, say if you have 1 site-to-site vpn and 9 RA vpn which has a total of 10 sessions VPN.

Concerning

Error of customer Cisco VPN connection ASA 5505

I am unable to connect to the vpn I created on my ASA 5505 using the Cisco VPN Client on a Windows machine. The log of the vpn client and the config of the ASA 5505 is lower. Any help to solve this is appreciated.

CISCO VPN CLIENT LOG

Cisco Systems VPN Client Version 5.0.06.0160

Copyright (C) 1998-2009 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 6.1.7600

Config files directory: C:\Program Cisco Systems Client\

1 09:34:23.030 13/04/11 Sev = Info/4 CM / 0 x 63100002

Start the login process

2 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

3 09:34:23.061 13/04/11 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "71.xx.xx.253".

4 09:34:23.061 13/04/11 Sev = Info/6 IKE/0x6300003B

Attempts to establish a connection with 71.xx.xx.253.

5 09:34:23.061 13/04/11 Sev = Info/4 IKE / 0 x 63000001

From IKE Phase 1 negotiation

6 09:34:23.077 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 71.xx.xx.253

7 09:34:23.170 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

8 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

9 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer is a compatible peer Cisco-Unity

10 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports XAUTH

11 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports the DPD

12 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports NAT - T

13 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000001

Peer supports fragmentation IKE payloads

14 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000001

IOS Vendor ID successful construction

15 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) at 71.xx.xx.253

16 09:34:23.170 13/04/11 Sev = Info/6 IKE / 0 x 63000055

Sent a keepalive on the IPSec Security Association

17 09:34:23.170 13/04/11 Sev = Info/4 IKE / 0 x 63000083

IKE port in use - Local Port = 0xEB07, Remote Port = 0 x 1194

18 09:34:23.170 13/04/11 Sev = Info/5 IKE / 0 x 63000072

Automatic NAT detection status:

Remote endpoint is NOT behind a NAT device

This effect is behind a NAT device

19 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

20 09:34:23.170 13/04/11 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

21 09:34:23.186 13/04/11 Sev = Info/5 IKE/0x6300005E

Customer address a request from firewall to hub

22 09:34:23.186 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to 71.xx.xx.253

23 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

24 09:34:23.248 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

25 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 172.26.6.1

26 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.0.0

27 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 172.26.0.250

28 09:34:23.248 13/04/11 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 172.26.0.251

29 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000000

30 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = TLCUSA

31 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

32 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (1) built by manufacturers on Wednesday 5 May 09 22:45

33 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

34 09:34:23.248 13/04/11 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194

35 09:34:23.248 13/04/11 Sev = Info/4 CM / 0 x 63100019

Data in mode Config received

36 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000056

Received a request from key driver: local IP = 172.26.6.1, GW IP = 71.xx.xx.253, Remote IP = 0.0.0.0

37 09:34:23.264 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > QM ISAKMP OAK * (HASH, SA, NO, ID, ID) to 71.xx.xx.253

38 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

39 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

40 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify has value of 86400 seconds

41 09:34:23.326 13/04/11 Sev = Info/5 IKE / 0 x 63000047

This AA is already living from 0 seconds, setting the expiration to 86400 seconds right now

42 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

43 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

44 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO *(HASH, DEL) to 71.xx.xx.253

45 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000049

IPsec security association negotiation made scrapped, MsgID = 89EE7032

46 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

47 09:34:23.326 13/04/11 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = 71.xx.xx.253

48 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000058

Received an ISAKMP for a SA message no assets, I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8

49 09:34:23.326 13/04/11 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">

50 09:34:26.696 13/04/11 Sev = Info/4 IKE/0x6300004B

IKE negotiation to throw HIS (I_Cookie = 2617522400DC1763 R_Cookie = 029325381036CCD8) reason = DEL_REASON_IKE_NEG_FAILED

51 09:34:26.696 13/04/11 Sev = Info/4 CM / 0 x 63100012

ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system

52 09:34:26.696 13/04/11 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

53 09:34:26.696 13/04/11 Sev = Info/6 CM / 0 x 63100046

Set indicator established tunnel to register to 0.

54 09:34:26.696 13/04/11 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

----------------------------------------------------------------------------------------

ASA 5505 CONFIG

: Saved

:

ASA Version 8.2 (1)

!

ciscoasa hostname

domain masociete.com

activate tdkuTUSh53d2MT6B encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

!

interface Vlan1

nameif inside

security-level 100

IP 172.26.0.252 255.255.0.0

!

interface Vlan2

nameif outside

security-level 0

IP address 71.xx.xx.253 255.255.255.240

!

interface Ethernet0/0

switchport access vlan 2

Speed 100

full duplex

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passive FTP mode

clock timezone IS - 5

clock to summer time EDT recurring

DNS server-group DefaultDNS

domain masociete.com

access-list LIMU_Split_Tunnel_List note the network of the company behind the ASA

Standard access list LIMU_Split_Tunnel_List allow 172.26.0.0 255.255.0.0

outside_access_in list extended access permit icmp any one

outside_access_in list extended access udp allowed any any eq 4500

outside_access_in list extended access udp allowed any any eq isakmp

outside_access_in list extended access permit tcp any host 71.xx.xxx.251 eq ftp

outside_access_in list extended access permit tcp any host 71.xx.xxx.244 eq 3389

inside_outbound_nat0_acl list of allowed ip extended access all 172.26.5.192 255.255.255.240

inside_outbound_nat0_acl list of allowed ip extended access all 172.26.6.0 255.255.255.128

pager lines 24

Enable logging

asdm of logging of information

Outside 1500 MTU

Within 1500 MTU

local pool VPN_POOL 172.26.6.1 - 172.26.6.100 255.255.0.0 IP mask

ICMP unreachable rate-limit 1 burst-size 1

enable ASDM history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_outbound_nat0_acl

NAT (inside) 1 0.0.0.0 0.0.0.0

static (inside, outside) 71.xx.xxx.251 172.26.5.9 netmask 255.255.255.255

static (inside, outside) 71.xx.xxx.244 172.26.0.136 netmask 255.255.255.255

Access-group outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 71.xx.xxx.241 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

Enable http server

http 172.26.0.0 255.255.0.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5

Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 30

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

dhcpd outside auto_config

!

no basic threat threat detection

no statistical access list - a threat detection

no statistical threat detection tcp-interception

WebVPN

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

value of server WINS 172.26.0.250 172.26.0.251

value of 172.26.0.250 DNS server 172.26.0.251

Protocol-tunnel-VPN IPSec l2tp ipsec svc

value by default-field TLCUSA

internal LIMUVPNPOL1 group policy

LIMUVPNPOL1 group policy attributes

value of 172.26.0.250 DNS server 172.26.0.251

VPN-idle-timeout 30

Protocol-tunnel-VPN IPSec l2tp ipsec

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list LIMU_Split_Tunnel_List

the address value VPN_POOL pools

internal TLCVPNGROUP group policy

TLCVPNGROUP group policy attributes

value of 172.26.0.250 DNS server 172.26.0.251

Protocol-tunnel-VPN IPSec l2tp ipsec svc

Re-xauth disable

enable IPSec-udp

value by default-field TLCUSA

barry.julien YCkQv7rLwCSNRqra06 + QXg password user name is nt encrypted privilege 0

username barry.julien attributes

VPN-group-policy TLCVPNGROUP

Protocol-tunnel-VPN IPSec l2tp ipsec

bjulien bhKBinDUWhYqGbP4 encrypted password username

username bjulien attributes

VPN-group-policy TLCVPNGROUP

attributes global-tunnel-group DefaultRAGroup

address VPN_POOL pool

Group Policy - by default-DefaultRAGroup

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared-key *.

tunnel-group DefaultRAGroup ppp-attributes

no authentication ms-chap-v1

ms-chap-v2 authentication

type tunnel-group TLCVPNGROUP remote access

attributes global-tunnel-group TLCVPNGROUP

address VPN_POOL pool

Group Policy - by default-TLCVPNGROUP

IPSec-attributes tunnel-group TLCVPNGROUP

pre-shared-key *.

ISAKMP ikev1-user authentication no

tunnel-group TLCVPNGROUP ppp-attributes

PAP Authentication

ms-chap-v2 authentication

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:b94898c163c59cee6c143943ba87e8a4

: end

enable ASDM history

can you try to change the transformation of dynamic value ESP-3DES-SHA map.

for example

remove the encryption scheme dynamic-map outside_dyn_map 20 transform-set TRANS_ESP_3DES_MD5

and replace with

Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

Can I get the total number of records that meet the conditions of a query using the Table API?

Hello
A < row > TableIterator is returned when I ask operations using the index of tables. If I want to get the total number of records, I count one by one using the returned TableIterator < row >.

Can I get the total number of records directly meets the conditions of the query?
I can get the total number of records directly the request of the meeting of the conditions of CLI using the command Global table - name tableName - count - index index-name-field fieldName - start startValue-end endValue.
Can I get the same results using the Table API?
I used MongoDB and NoSQL Oracle for about a year. According to the experience of the use of these dbs, I think mongoDB querying interface is powerful. In the contras, the query interface is relatively simple, which results is a lot of work that is usually a long time in the client side.

Hello

Counting records in a database is a tricky thing. Any system that gives you an accurate count of the records will have a hotspot of concurrency on updates, namely the place where the counting is maintained. Such a count is a problem of performance in addition to competitive access problem. The problem is even more difficult in a system widely distributed such a NoSQL database.

The CLI has overall command that counts, but does so by brutal force - iterate keys that correspond to the parameters of the operation. This is how you must do this within the API. There is not a lot of code, but you have to write. You certainly want to use TableIterator TableAPI.tableKeysIterator (), because a key iteration is significantly faster than the iteration of lines. Just one iteration and count.

If you use TableAPI.multiGet () and a key with a touch of brightness full then, in fact, count the results as they are returned in a single piece (a list).

Kind regards

George

How to get the total number of occurrences based on the value of a column.

Hi all

It is the first time I'll ask the question here on your forum, but since then followed several threads. I guess it's now my turn to ask a question. Anyway here's the thing, I have a query that should return to count the number of rows based on the value of HOUSING. Something like this:

-----

WIPDATAVALUE          SLOT             N            M
1-2                   TRALTEST43S1     1            3
1-2                   TRALTEST43S1     2            3
3                     TRALTEST43S1     3            3
4-6                   TRALTEST43S2     1            4
4-6                   TRALTEST43S2     2            4
4-6                   TRALTEST43S2     3            4
7                     TRALTEST43S2     4            4

-----

As you can see above, on the TRALTEST43S1 of the SLOT, there are three occurrences, so M (Total number of occurrences) must be three and this column N he's counting. It is the same with the TRALTEST43S2 of the SLOT. It's the query I have so far:

SELECT DISTINCT
WIPDATAVALUE, SLOT
, LEVEL AS n
, m 
FROM
(
  SELECT
    WIPDATAVALUE
    , SLOT
    , (dulo - una) + 1 AS m 
  FROM
  (
    SELECT 
      WIPDATAVALUE
      , SLOT
      , CASE WHEN INSTR(wipdatavalue, '-') = 0 THEN wipdatavalue ELSE SUBSTR(wipdatavalue, 1, INSTR(wipdatavalue, '-')-1) END AS una
      , CASE WHEN INSTR(wipdatavalue, '-') = 0 THEN wipdatavalue ELSE SUBSTR(wipdatavalue, INSTR(wipdatavalue, '-') + 1) END AS dulo
    FROM trprinting
    WHERE (containername = :lotID OR SLOT= :lotID) AND WIPDATAVALUE LIKE :wip
  )
) CONNECT BY LEVEL <= m
ORDER BY wipdatavalue;

And it leads to something like this:
-----

WIPDATAVALUE          SLOT             N            M
1-2                   TRALTEST43S1     1            2
1-2                   TRALTEST43S1     2            2
3                     TRALTEST43S1     1            1
4-6                   TRALTEST43S2     1            3
4-6                   TRALTEST43S2     2            3
4-6                   TRALTEST43S2     3            3
7                     TRALTEST43S2     1            1

-----

I think that my current query based results M and N on WIPDATAVALUE and not HOUSING that's why I get the wrong result. I also tried to use WITH instruction and it works well, but unfortunately, our system cannot accept the subquery factoring.

I know that you guys will be of help because you are all awesome. Thank you all

Published by: 1001275 on April 19, 2013 20:07

Published by: 1001275 on April 19, 2013 20:18

Hello

1001275 wrote:
Hi sb92075,

You are right that it is available with this version. But our system doesn't put queries that use subquery factoring.

What system are you talking about? If you really have something that prevents you from using all the features of Oacle, you should seriously think about fixing it.

Any other ideas on how we can do this without help WITH clause?

Yes; If a WITH clause is referenced that once, it can be re-written as a point of view online:

SELECT       wipdatavalue
,       slot
,       ROW_NUMBER () OVER ( PARTITION BY  slot
                             ORDER BY          low_number
                    )                    AS m
,       COUNT (*)     OVER ( PARTITION BY  slot )     AS n
FROM       (     -- Begin in-line view (got_numbers)
            SELECT     wipdatavalue
          ,     slot
          ,     TO_NUMBER ( SUBSTR ( wipdatavalue
                                    , 1
                               , INSTR ( wipdatavalue || '-'
                                           , '-'
                                    ) - 1
                               )
                        )          AS low_number
          ,     TO_NUMBER ( SUBSTR ( wipdatavalue
                                    , 1 + INSTR ( wipdatavalue
                                                   , '-'
                                            )
                               )
                        )          AS high_number
          FROM     trprinting
       )     -- End  in-line view got_numbers
CONNECT BY     LEVEL               <= high_number + 1 - low_number
     AND     low_number          = PRIOR low_number
     AND     PRIOR SYS_GUID ()      IS NOT NULL
ORDER BY  low_number
,            m
;

Total number of active, last login, inactive etc.

Hello
Need to know some way or script which will display the number of connection of users, inactive, the total number of users and their details on Oracle 10 g.
Thanks in advance.

Richa,

Check this box if this works for you

  col sql_text for a80
set pages 200
set line 900
col PROGRAM for a20
col MACHINE for a20
alter session set nls_date_format='dd-mon-yyyy hh24:mi:ss';
col event for a40
select *
  from (select /*+ RULE  */sa.sql_id, s.sid "SID", s.serial# "SERIAL",
         s.program "PROGRAM",
         s.machine "MACHINE",
         sa.SQL_TEXT "SQL_TEXT",
         s.logon_time,
         round(s.last_call_et / 60,0) "Inact_Min",
         s.username,
         s.osuser,
         s.status
          from v$sqlarea sa, v$session s, v$process vp
         where sa.address = s.sql_address
                      and s.paddr = vp.addr
         order by CPU_TIME desc);

Thank you
Ajay more
http://www.moreajays.com

total number of vCPU for your pCPU

Hi people,
We have a battery of ESX servers with 3 guests with 2 dual-core processors on each host. If this makes total of 12 sesc.
I wonder how many total number of vCPUs I hire? Is there a connection? I know that 1 to 1 is not normal since we have already 18 subscribed vCPUs.
Any help will be greatly appreciated.
Thank you!
KeV

The maximum rate of CPU for 4.1 are a bit extreme...

Logical CPU for each host: 128

Virtual host CPU: 512

Virtual CPU by heart: 25

Given that the OP has only of the proc dual core and only two connectors hosts, I didn't see much interest in this info before posting... Since the chances of the hosts maximum handling is essentially zero...

As requested to the OP, there is no set ratio for how vCPU, you will be able to get on your pCPU (other than the maximum value of 25: 1)... Unless you are VM do almost anything (except running an operating system), you will get there with your current hosts... Even in this case, it would be a stretch.

VMware VCP4

Review the allocation of points for "useful" or "right" answers.

Total number of concurrent VPN connections.

Similar Questions

Maybe you are looking for