Number of tunnel VPN LRT224

Hello!

I trying to get the LRT224 and need to understand something before you buy it:

Manual user said it supports 50 VPN tunnels, but in the demo of the user Web interface, I can see PPTP 45 + 5 + 5 OpenVPN EasyLink - how these add up?

In addition, these numbers limit the simultaneous number of tunnels or VPN accounts? For example can I have 10 accounts Easy Link (Open VPN) created and use only 3 of them at the same time, for example?

Thank you very much!

Hello, Amalakhov! These are the VPN router features:

-50 via IPsec Site to Site tunnels
-5 (compatible with OpenVPN) SSL tunnels
-5 PPTP tunnels
-IPsec 110 Mbps throughput
-12 Mbps SSL throughput

The maximum number of concurrent VPN connections through the router depends on the flow of IPSec. Your connection will be sacrificed if you would connect more than 5 tunnels at the same time.

Tags: Linksys Products

Similar Questions

Tunnel VPN from Site to Site dynamic

I spent the last 2 days, try to set up a dynamic tunnel VPN site to site of a Cisco 5510 to a Cisco SA540. The 540 is a dynamic supplier that can not be changed. There a dyndns account.

I was lucky that the other 10 sites are all static and the ADSM Assistant creates these tunnels without problems.

What I try to do is:

Is it possible to do it VIA ADSM?

If this isn't the case, someone please in detail can help with orders.

Kind regards

PP

Hello Paul,

This is possible thanks to the ASDM, but you do have to use some advanced settings:

Configuration > VPN Site to Site > advanced > Tunnel groups

It change the group called "DefaultL2LGroup" and add the brightness button before the SA540 (Note: all of your sites with dynamic IP addresses will have the same key communicated in advance, if you have IPSec VPN clients, it will be a good idea to use a different key).

Click ok and then apply.

Then go to Configuration > VPN Site to Site > advanced > Crypto Maps and add a new entry dynamic

Make sure that you match the phase 2 are on your SA540 (pictured ESP-AES-128-SHA), select a dynamic strategy and make the last sequence number (65535) then ok, apply.

Then go to Configuration > VPN Site to Site > advanced > IKE policies and make sure you have corresponding policies of the phase 1.

If no corresponding policy is found, add them.

Through CLI:

IKEv1 crypto policy 1

preshared authentication

aes encryption

sha hash

Group 2

Crypto-map dynamic outside_dyn_map 65535 set transform-set ESP-AES-128-SHA ikev1

CARD crypto ipsec-isakmp 65535 dynamic outside_dyn_map

IPSec-attributes tunnel-group DefaultL2LGroup

IKEv1 pre-shared-key *.

I hope this helps.

Confusion over the number of tunnels

Hi all

I'm very confused about the number of tunnels formed in my ASA 5520. By CLI, I see two IPSec tunnels, but through ASDM, I get the data you see in the attached picture. Someone knows about it. Thank you

VPN-ASA5520-BLUR # sh vpn-sessiondb summary

Summary of the current Session

Sessions:
Active principles: Cumulative: simultaneous peak: inactive
SSL VPN               :       0 :         20 :               3
Clientless only: 0: 3: 1
Client: 0: 17: 2: 0
IPsec remote access: 2:10:2
Totals: 02:30

Information about the license:
IPsec: 750 configured: 750 Active: 2 load: 0%
SSL VPN: 25 configured: assets 25: 0 load: 0%
Active principles: Cumulative: simultaneous peak
IPsec               :          2 :         10 :               2
SSL VPN             :          0 :         20 :               3
Totals              :          2 :         30

NAC Active Sessions:
No NAC session to display

Mapping sessions VLANS active:
No session mapping VLAN to display
VPN-ASA5520-BLUR # sh clock
07:58:34.698 METS Tuesday, June 12, 2012
VPN-ASA5520-BLUR.

The output of the ASDM is likely to match the output of 'see the vpn-sessiondb' without the key word "Summary", which also include VPN IPSec LAN - to - LAN both tunnels.

Tunnel VPN and NAT

Hello. I'm creating a tunnel VPN IPSec LAN - to - LAN of my ASA5510 to another network but met an obstacle bit. My counterpart on the other side has informed me that he already has a VPN tunnel to another company that has the same IP range as my network(10.100.16.0 /24) and can not create the tunnel.

I was wondering is it possible to use NAT on the VPN tunnel so that traffic that goes from my network over the VPN tunnel gets translated and my counterpart on the other side sees this reflects the range of IP addresses?

Thanks in advance for any help.

Hello

Yes, you can use the same address you already use for internet access.

Just update your list of access crypto to reflect the new address and to ensure that the third party did the same.

Jon

Tunnel VPN site to Site with 2 routers Cisco 1921

Hi all

So OK, I'm stumped. I create much s2s vpn tunnels before, but this one I just can't go there. It's just a tunnel VPN Site to Site simple using pre-shared keys. I would appreciate it if someone could take a look at our configs for both routers running and provide a comment. This is the configuration for both routers running. Thank you!

Router 1

=======

Current configuration: 4009 bytes

!

! Last configuration change at 19:01:31 UTC Wednesday, February 22, 2012 by asiuser

!

version 15.0

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

SJWHS-RTRSJ host name

!

boot-start-marker

boot-end-marker

!

!

No aaa new-model

!

!

!

!

No ipv6 cef

IP source-route

IP cef

!

!

DHCP excluded-address 192.168.200.1 IP 192.168.200.110

DHCP excluded-address IP 192.168.200.200 192.168.200.255

!

IP dhcp POOL SJWHS pool

network 192.168.200.0 255.255.255.0

default router 192.168.200.1

10.10.2.1 DNS server 10.10.2.2

!

!

no ip domain search

IP-name 10.10.2.1 Server

IP-name 10.10.2.2 Server

!

Authenticated MultiLink bundle-name Panel

!

!

Crypto pki trustpoint TP-self-signed-236038042

enrollment selfsigned

name of the object cn = IOS - Self - signed - certificate - 236038042

revocation checking no

rsakeypair TP-self-signed-236038042

!

!

TP-self-signed-236038042 crypto pki certificate chain

certificate self-signed 01

30820241 308201AA A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030

8B1E638A EC

quit smoking

license udi pid xxxxxxxxxx sn CISCO1921/K9

!

!

!

redundancy

!

!

!

!

crypto ISAKMP policy 10

md5 hash

preshared authentication

ISAKMP crypto key presharedkey address 112.221.44.18

!

!

Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1

!

map CryptoMap1 10 ipsec-isakmp crypto

defined by peer 112.221.44.18

game of transformation-IPSecTransformSet1

match address 100

!

!

!

!

!

interface GigabitEthernet0/0

192.168.200.1 IP address 255.255.255.0

automatic duplex

automatic speed

!

!

interface GigabitEthernet0/1

Description wireless bridge

IP 172.17.1.2 255.255.255.0

automatic duplex

automatic speed

!

!

interface FastEthernet0/0/0

Verizon DSL description for failover of VPN

IP 171.108.63.159 255.255.255.0

automatic duplex

automatic speed

card crypto CryptoMap1

!

!

!

Router eigrp 88

network 172.17.1.0 0.0.0.255

network 192.168.200.0

redistribute static

passive-interface GigabitEthernet0/0

passive-interface FastEthernet0/0/0

!

IP forward-Protocol ND

!

no ip address of the http server

local IP http authentication

IP http secure server

!

IP route 0.0.0.0 0.0.0.0 172.17.1.1

IP route 112.221.44.18 255.255.255.255 171.108.63.1

!

access-list 100 permit ip 192.168.200.0 0.0.0.255 10.10.0.0 0.0.255.255

!

!

!

!

!

!

control plan

!

!

!

Line con 0

Synchronous recording

local connection

line to 0

line vty 0 4

exec-timeout 30 0

Synchronous recording

local connection

transport input telnet ssh

!

Scheduler allocate 20000 1000

end

=======

Router 2

=======

Current configuration: 3719 bytes

!

! Last configuration change at 18:52:54 UTC Wednesday, February 22, 2012 by asiuser

!

version 15.0

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

SJWHS-RTRHQ host name

!

boot-start-marker

boot-end-marker

!

logging buffered 1000000

!

No aaa new-model

!

!

!

!

No ipv6 cef

IP source-route

IP cef

!

!

!

!

no ip domain search

!

Authenticated MultiLink bundle-name Panel

!

!

Crypto pki trustpoint TP-self-signed-3490164941

enrollment selfsigned

name of the object cn = IOS - Self - signed - certificate - 3490164941

revocation checking no

rsakeypair TP-self-signed-3490164941

!

!

TP-self-signed-3490164941 crypto pki certificate chain

certificate self-signed 01

30820243 308201AC A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030

2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

EA1455E2 F061AA

quit smoking

license udi pid xxxxxxxxxx sn CISCO1921/K9

!

!

!

redundancy

!

!

!

!

crypto ISAKMP policy 10

md5 hash

preshared authentication

ISAKMP crypto key presharedkey address 171.108.63.159

!

86400 seconds, duration of life crypto ipsec security association

!

Crypto ipsec transform-set esp-3des esp-md5-hmac IPSecTransformSet1

!

map CryptoMap1 10 ipsec-isakmp crypto

defined by peer 171.108.63.159

game of transformation-IPSecTransformSet1

match address 100

!

!

!

!

!

interface GigabitEthernet0/0

no ip address

automatic duplex

automatic speed

!

!

interface GigabitEthernet0/0.1

encapsulation dot1Q 1 native

IP 10.10.1.6 255.255.0.0

!

interface GigabitEthernet0/1

IP 172.17.1.1 255.255.255.0

automatic duplex

automatic speed

!

!

interface FastEthernet0/0/0

IP 112.221.44.18 255.255.255.248

automatic duplex

automatic speed

card crypto CryptoMap1

!

!

!

Router eigrp 88

Network 10.10.0.0 0.0.255.255

network 172.17.1.0 0.0.0.255

redistribute static

passive-interface GigabitEthernet0/0

passive-interface GigabitEthernet0/0.1

!

IP forward-Protocol ND

!

no ip address of the http server

local IP http authentication

IP http secure server

!

IP route 0.0.0.0 0.0.0.0 112.221.44.17

!

access-list 100 permit ip 10.10.0.0 0.0.255.255 192.168.200.0 0.0.0.255

!

!

!

!

!

!

control plan

!

!

!

Line con 0

Synchronous recording

local connection

line to 0

line vty 0 4

exec-timeout 30 0

Synchronous recording

local connection

transport input telnet ssh

!

Scheduler allocate 20000 1000

end

When the GRE tunnel carries your traffic to private ip range, your ACL must contain address of the host of point to point the IPSec tunnel.

Since then, both routers are running EIGRP in the corporate network, let the EIGRP Exchange routes via GRE tunnel, which is a good practice, rather than push the ip ranges private individual through the IPSec tunnel.

Let me know, if that's what you want.

Thank you

Tunnel VPN RV-042 for Dual WAN Failover backup function

We have customers with dual WAN failover scenarios with site-to-site VPN tunnels.

In the past, the VPN tunnel backup feature has been available in the RV-082.

One of the new RV-042 firmware versions have the function of backup Tunnel VPN available?

The feature is supported on the RV042 V3 hardware.

Bring up the tunnel vpn crypto without interesting traffic map

Is it possible on ASA to bring up the tunnel vpn site to site static crypto map without generating interesting traffic? I want to reverse route injection generate road dynamic until traffic begins to flow.

Roman,

Unless something chnaged recently RRI inserts routes without present SAs, meaning that they are static (in contrast to current default behavior on IOS 12.4 (9) T-I_think leave).

But to answer the question, in more recent versions, you can bring up the tunnel using packet - trace CLI.

M.

Edit: request for improvement that will present the same features of IPP on ASA as on IOS:

http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCsx67450

Tunnel VPN site to Site - aggressive Mode

I searched the community for answers to this and that you have not found quite what I was looking for (or what seems logical). I have an ASA 5510 to A site with one website VPN tunnel to a SonicWall to site B. Which works very well. I need to create a tunnel for site C to site a using a tunnel of aggressive mode. I'm not quite sure how to do this. Any suggestion would be great!

NOTE: I have included the parts of the running configuration that seem relevant to me. If I missed something please let me know.

ASA Version 8.2 (1)

interface Ethernet0/0

nameif outside

security-level 0

IP 1.2.3.4 255.255.255.248

!

10.5.2.0 IP Access-list extended site_B 255.255.255.0 allow 10.205.2.0 255.255.255.128

access extensive list ip 10.5.2.0 site_C allow 255.255.255.0 10.205.2.128 255.255.255.128

dynamic-access-policy-registration DfltAccessPolicy

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac 3des-sha1

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto VPN 30 card matches the address site_B

card crypto VPN 30 peer set 4.3.2.1

crypto VPN 30 the transform-set 3des-sha1 value card

card crypto VPN 40 corresponds to the address site_C

card crypto VPN. 40 set peer 8.7.6.5

crypto VPN. 40 the transform-set 3des-sha1 value card

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Crypto isakmp nat-traversal 30

crypto ISAKMP ipsec-over-tcp port 10000

attributes of Group Policy DfltGrpPolicy

Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

tunnel-group 4.3.2.1 type ipsec-l2l

4.3.2.1 tunnel-group ipsec-attributes

pre-shared-key *.

tunnel-group 8.7.6.5 type ipsec-l2l

IPSec-attributes tunnel-group 8.7.6.5

pre-shared-key *.

David,

Please try this:

clear crypto ipsec its peer site_c_IP

clear configure VPN 40 crypto card

card crypto VPN 10 corresponds to the address site_C

card crypto VPN 10 set peer 8.7.6.5

crypto VPN 10 the transform-set 3des-sha1 value card

debug logging in buffered memory

capture drop all circular asp type

capture capin interface inside the match ip 10.5.2.0 255.255.255.0 10.205.2.128 255.255.255.128

After generating the traffic and INTERNAL of the machine behind the ASA:

view Journal | 10.205.2 Inc.

See the fall of cap. 10.205.2 Inc.

view Cape capin

In case it does not work:

(a) show the crypto classic table ASP.

(b) details of vpn-framework for table ASP.

(c) show cry its site_c peer ipsec

(d) entry packet - trace within the icmp 10.5.2.15 8 0 10.205.2.130 detail

(e) see the crypto ipsec his

At the same time, please.

Let me know how it goes.

Thank you

Portu.

Please note all useful posts

Impossible to access them Internert through the split tunneling VPN client.

I divided tunnel configured on a PIX 515. The remote VPN client connects to the PIX very well and can ping hosts on the internal network, but cannot access the Internet. Am I missing something? My config as shown below.

In addition, I don't see the routes on the VPN client via statistics (screenshot below)

All opinions are appreciated.

Rob

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------

8.0 (3) version PIX

!

hostname PIX-to-250

enable the encrypted password xxxxx

names of

!

interface Ethernet0

nameif outside

security-level 0

IP address x.x.x.250 255.255.255.240

!

interface Ethernet1

nameif inside

security-level 100

IP 192.168.9.1 255.255.255.0

!

XXXXX encrypted passwd

passive FTP mode

DNS domain-lookup outside

DNS server-group Ext_DNS

Server name 194.72.6.57

Server name 194.73.82.242

the LOCAL_LAN object-group network

object-network 192.168.9.0 255.255.255.0

object-network 192.168.88.0 255.255.255.0

Internet_Services tcp service object-group

port-object eq www

area of port-object eq

EQ object of the https port

port-object eq ftp

EQ object of port 8080

port-object eq telnet

the WAN_Network object-group network

object-network 192.168.200.0 255.255.255.0

ACLOUT list extended access allowed object-group LOCAL_LAN udp any eq log field

ACLOUT list extended access allow icmp object-group LOCAL_LAN no matter what paper

ACLOUT list extended access permitted tcp object-group LOCAL_LAN connect to any object-group Internet_Services

access-list extended ACLIN all permit icmp any what newspaper echo-reply

access-list extended ACLIN all permit icmp any how inaccessible journal

access-list extended ACLIN allowed icmp no matter what newspaper has exceeded the time

Comment by split_tunnel_list-LAN Local access list

split_tunnel_list list standard access allowed 192.168.9.0 255.255.255.0

access-list extended SHEEP allowed object-group ip LOCAL_LAN 192.168.100.0 255.255.255.0

pager lines 24

Enable logging

Outside 1500 MTU

Within 1500 MTU

IP local pool testvpn 192.168.100.1 - 192.168.100.99

no failover

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0 access-list SHEEP

NAT (inside) 1 0.0.0.0 0.0.0.0

Access-group ACLIN in interface outside

ACLOUT access to the interface inside group

Route outside 0.0.0.0 0.0.0.0 195.171.252.45 1

Route inside 192.168.88.0 255.255.255.0 192.168.88.254 1

Route inside 192.168.199.0 255.255.255.0 192.168.199.254 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout, uauth 0:05:00 absolute

dynamic-access-policy-registration DfltAccessPolicy

Enable http server

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-3des esp-sha-hmac Set_1

Crypto-map dynamic outside_dyn_map 10 game of transformation-Set_1

life together - the association of security crypto dynamic-map outside_dyn_map 10 seconds 280000

Crypto-map dynamic outside_dyn_map 10 the value reverse-road

outside_map 10 card crypto ipsec-isakmp dynamic outside_dyn_map

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 1

preshared authentication

3des encryption

sha hash

Group 2

life 43200

crypto ISAKMP policy 65535

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

a basic threat threat detection

Statistics-list of access threat detection

internal testvpn group policy

attributes of the strategy of group testvpn

Protocol-tunnel-VPN IPSec

Split-tunnel-policy tunnelspecified

name of user testuser encrypted password xxxxxx

type tunnel-group testvpn remote access

tunnel-group testvpn General-attributes

address testvpn pool

Group Policy - by default-testvpn

testvpn group of tunnel ipsec-attributes

pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

inspect the icmp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:5dcb5dcdff277e1765a9a0c366b88b9e

: end

# 250 A - PIX

You have not assigned the ACL split tunnel to your strategy.

PLS, configure the following:

attributes of the strategy of group testvpn

value of Split-tunnel-network-list split_tunnel_list

Can anyone help me how I will work with tunnel VPN Failover.

Hi Experts,

I have two 5520 ASA one headquarters and another is disaster recovery. So I need to build the tunnel of the Branch Office Chief at the office that I have 3g router.

So I need to build failover to ASA of recovery after a disaster. Please can someone help me what would be the best option that makes my task complete.

Thank you

Mohammed

Hello

I guess you are looking for a relief tunnel VPN router. Here's how you set it up:

http://www.Cisco.com/en/us/products/sw/secursw/ps5318/products_user_guide_chapter09186a0080531f28.html#wp1002246

I hope this helps.

Kind regards

Anisha

P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

tunnel VPN ZFW problem

Recently I tried to build a tunnel VPN of LAN LAN 2 connecting an Asa to a current zone based firewall 2911. It's a standard IPSec psk tunnel nothing complicated. I got the tunnel to establish, but I could only get traffic to encap on the side of the SAA and decap on the side of 2911. I couldn't return circulation. I followed this doc classic here for IPSec in the last example.

http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps5708/ps5710/ps1018/...

And I don't know that the SAA is right I have built a ton of those but I am new to zfw. I don't see anything about a NAT rule exempt. But as all used real IPs instead of NAT I wasn't sure and I have found no info. I do free NAT? If If you are using a roadmap on the end you NAT overload line config as in the past?

I also have a pair of area to "self" and I didn't know if I need something there to be able to do a ping from inside the 2911 interface when the tunnel is at the top of the remote end. Thank you

Is the pair area yourself, outside of itself?

And you say that you do not use only NAT, have real addresses (public routable addresses?), so why you have to make an exception for NAT you have not?

How to secure Tunnel VPN

Hello

I installed a tunnel VPN between ASA and PIX. I want to implement security on the ASA or PIX so that some remote endpoint specfic IP can access resources of tunnel. is it possible to block additional IP addresses?

Thank you

Amardeep

Please read this link, you can implement VPN-filter.

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

Thank you

Ajay

PIX515 limit the number of Tunnels?

Hi all

Is there a limit to the number of VPN tunnels that you can create on a Pix515?

Thanks for any help

MG

There are limiting the number of VPN peers, which is actually the same thing. Check your license features by publishing the underside as the cli: -.

Show worm - you should see something like: -.

The devices allowed for this platform:

The maximum physical Interfaces: 3

VLAN maximum: 10

Internal hosts: unlimited

Failover: disabled

VPN - A: enabled

VPN-3DES-AES: enabled

Cut - through Proxy: enabled

Guardians: enabled

URL filtering: enabled

Security contexts: 0

GTP/GPRS: disabled

VPN peers: unlimited

VPN peers, that's what you're looking for - numbered or unlimited! There is a limitation of thru - put encryption cannot have 1 million tunnels and expect to get MBs of through - put!

HTH.

Problems with basic setup and split tunneling VPN

I created a SSL VPN in an ASA CISCO ASDM 6.6 8.6 running.
IM able to connect to the VPN and reach all the devices with the LAN but I am not able to browse the web. When I activate the tunnel split Im able to browse the web, but then Im not able to reach any internal device.
Here is part of the show's run:

network of the RedInterna object
150.211.101.0 subnet 255.255.255.0
Description Red Interna
network of the NETWORK_OBJ_10.4.1.0_28 object
subnet 10.4.1.0 255.255.255.240
inside_access_in list extended access permitted ip object RedInterna all
Standard access list VPN_INTERNET allow 150.211.101.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
local pool VPN_POOL 10.4.1.1 - 10.4.1.14 255.255.255.240 IP mask
failover
secondary failover lan unit
failover lan interface GigabitEthernet0 fail-1/2
key changeover *.
failover interface ip fail-1 10.3.1.21 255.255.255.252 watch 10.3.1.22
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
enable ASDM history
ARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 non-proxy-arp-search to itinerary
!
NAT source auto after (indoor, outdoor) dynamic one interface
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
Route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
Route inside 150.211.0.0 255.255.0.0 10.1.1.78 1

WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_VPN_ group strategy
attributes of Group Policy GroupPolicy_VPN_
WINS server no
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
dominio.com.MX value by default-field
type tunnel-group VPN_ remote access
attributes global-tunnel-group VPN_
address VPN_POOL pool
Group Policy - by default-GroupPolicy_VPN_
tunnel-group VPN_ webvpn-attributes
enable VPN_ group-alias
!

I m don't know if Im missing a few small details or Setup. Any help will be much appreciated.
Thank you!!!

Hello

When you use full VPN Tunnel (which is the default setting), you will have a number of things that you need to configure on the SAA.

First, the ASA by default will not allow traffic to enter via an interface and then exit through the same interface. It is essentially, what happens when the customer VPN traffic comes to the ASA and then heads on the Internet. In your case the traffic goes through the 'outside' and leaves via the 'outside' interface.

You will need this command

permit same-security-traffic intra-interface

You can check if their licence at the moment with the command

See the race same-security-traffic

Second, VPN users will need to have the NAT configuration like all users LAN behind the ASA real. So you basically configure dynamic PAT for 'outside' to 'outside' traffic

You can get there with the following configuration

network of the VPN-PAT object

subnet 10.4.1.0 255.255.255.240

dynamic NAT interface (outdoors, outdoor)

I suppose it should do for you to be able to connect to the Internet and the LAN when the VPN is active.

Hope this helps

Let me know how it goes.

-Jouni

Tunnel VPN Firewall (both sides of the Site B, same IP series)

Hi Experts,

I'm in a weird situation, hope I can get an answer from you guys.

I had created VPN tunnel to our customer on our firewall 3 years.

Now we create the VPN tunnel for new customer, but the IP settings to the new customer is the same as the former client. How can we get through this that we can not change the IP settings on both clients.

Here are the technical details

Older Client settings:

(1) our authorized Local LAN IP: 192.168.3.0/24

(2) customer Local LAN IP authorized: 10.0.0.0/8 (as several range of network to the client end)

New customer to make settings:

(1) our authorized Local LAN IP: 192.168.3.0/24

(2) authorized customer Local LAN IP: 10.10.16.0/24

10.10.32.0/24

Please help as well how we can make the settings without making any changes on the client side.

I am using firewall Watchguard XTM 515

Thank you best regards &,.

Mandeep

This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)

*

http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil

http://social.msdn.Microsoft.com/Forum

Number of tunnel VPN LRT224

Similar Questions

Maybe you are looking for