TOUCHSMART HP ENVY 17-J178CA: set the bios to boot to DVD

Similar Questions

• Laptop Presario CQ62: SETTING THE BIOS TO BOOT FROM a USB STICK

  I need to set the BIOS to boot from a usb key. The options in the BIOS are
  BOOT CD-ROM
  Startup disk
  Internal network card

  And in the boot order:
  USB disk on key/USB hard drive
  USB CD/DVD ROM drive

  Portable hard drive

  USB floppy drive
  Internal CD/DVD drive

  ! Network adapter (but it says that the ability to start will be disabled if the device is marked with an exclamation point, which, in my case, it is)

  A question who should I set to boot from a usb flash drive which has the operating system that you want to install Windows?

  I tried boot F9 options, but it gives me two options:
  Portable hard drive
  CD/DVD drive.
  No drive Flash Drive or USB in the list options.

  Then he said: press F10 for BIOS Setup Options. That's why I'm trying to see what to implement as boot device in the BIOS boot options.

• HP ENVY h8 - 1520t: set the bios for the site with riders

  I need jumper to clear the BIOS settings in the CMOS. Does not start to any menu or menu setup after getting out of battery and replacement.

  Thank you

  Chet wood

  Product number:

  C9D47AV #ABA

  • HP ENVY h8 - 1520t CTO desktop PC
  • Win 8 64-bit
  • Microprocessor Intel core i7-3770 CPU @ 34.0 Ghz
  • 8 GB MEM
  • Mem slot 1 8 GB 1600 Mhz Micron
  • Chart AMD Radeon HD-7570
  • Current RES 1920 x 1080
  • refresh rate 60
  • 2AD5 Board of Directors system 1.03

  BIOS 8.14

  2AD5 Board of Directors system 1.03

  The motherboard is the same as indicated, BUT the jumper CMOS block illustrated on the Web page must be another block I watched card mother pictures of this model from EBay and they show the jumper in the position that you indicated.  There are two blocks.  There are two blocks of blue jumpers with the configuration pins as shown in the picture I posted.  I think that what the picture posted is saying leave the jumper on the right side block is and only move the jumper on the left side of the position shown, then again.  Just to clarify, there is a block under this block, we want, and who says "ROM_RECOVERY" and this block has a single rider together 1-2.  Jumper block we are debating is actually marked "CMOS-PW.

  Hope that helps clear things upward.

• Trying to set the BIOS to boot from CD with Acronis HD clone software

  Want to 700-056.  16 GB of Ram.  Qurdro graphic K600.

  I just installed a 240 gb SSD, Kingston.

  To move the operating system (8.1), I need to boot from a DVD with Acronis program.

  Under the legacy in BIOS, Acronis is displayed.  I move under the legacy, but the computer still starts on C:.

  Where can I find detailed information about the BIOS and how to boot from the DVD?

  Jim Holmes

  Your welcome!

• Satellite U400: How to set the BIOS password & learn how to use facial recognition

  I have a Satellite U400 Satellite.

  Can someone direct me to a link of support for the implementation in passwords in BIOS?

  There are several options and I don't know what does what...
  Thanks for your help...

  Another point:

  I feel that the definition of a password or both in the BIOS will help the face recognition program to work, for some reason any.
  I NEVER managed to properly configure that, although I tried several times,
  go in accordance with the instructions.

  A lot of frustration and time, I would say.
  This is for safety.

  > Can someone direct me to a link of support for the implementation in passwords in BIOS?
  If you want to set the password in the BIOS you will need to access the BIOS by pressing the F2 key immediately after that the laptop has been powered.

  There is a 3rd tab security.
  There you can set the BIOS password. You would need to put everything first and then you must confirm the password once more to

  > I have the impression that the definition of a word or two in the BIOS will help the face recognition program to work, for some reason any.
  This s the password of BIOS nonsense has nothing to do with the reorganization of face.

  Here's a very useful thread that provides details on the reorganization of the face:
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=147434

  Check it out. It is very useful

• IBM think centre @ request for initialization of the system user password and a genius set the bios to lock keyboard can it is bypassed and how?

  Original title: IBM think centre @ start request.

  IBM think centre @ request for initialization of the system user password and a genius set the bios to lock keyboard can it is bypassed and how?

  Hi brandon1980,

  I recommend you contact your computer manufacturer for assistance. The manufacturer would be able to give details about the BIOS (Basic Input Output System) and find out if this feature can be disabled.

  Hope the helps of information.

• I can't get my PNY NVIDIA GT 520 to install in my Pavilion a6123w. I set the BIOS to PCIe

  I can't get the new video card GT 520 to stay in the Device Manager list.  I upgraded to a Psalm of 650 watts I set the BIOS to PCIe and also tried PCI.  I have disabled and also tried to uninstall the integrated video graphics card GeForce 6150 nForce 430.  The GT 520 worked twice after I leave the PC closed for several hours unplugged and then boot with the monitor connected to the GT 520 VGA connection.  Both times she came back to the integrated graphics card, which has no red color.  I have the latest driver for the installed GT 520 and he demonstrated to be driven to the integrated graphics card.  When the GT520 was working he executed perfectly and I used it for several hours each time.  The first time it worked until I close the PC (Pavilion Office a6123w) down to try to get the DVI on the GT 520 connection.  The next day, I left the PC for a few minutes after using it for about 2 hours.  When I got home, I had no signal on the screen.  I went from the connection to the integrated VGA and was back in the video.  It's the second GT 520 I tried, the first was returned to Fry, because the customer (?) support PNY suggested it might be a bad card and that I should up grade of PS.  I hope someone knows the specific steps to take to make the stay of GT520 as the main graphic.  I saw a suggestion on a site that said there may be a jumper or a way to disable the video edge physically.

  Oldwrench, welcome to the forum.

  I would uninstall all (driver, video card) that you have done and start over again.  I suggest to use Revo Uninstaller to remove the driver. I always use the advanced option. This will remove all files from the registry and hard drive.  Then, restart the system.  This should put you back where you started.

  When you install the discrete video card, integrated graphics subsystem should be automatically disabled.  Makes no changes in the BIOS.  This could be the cause of some problems.  Once this is done, you can install the latest video driver from nVidia.  Restart the system and see what happens.

  If your problem is solved, please click "accept as a Solution.

• Satellite U940-108 - how to configure the BIOS to boot double OS to SSD / HDD

  How can I set the BIOS to start multi os ssd and HDD?

  I want to boot from an OS SSD and other bones of the HARD drive,
  When I try to do, I've got windows error?

  Can you help me

  Hello

  I guess you want to install the operating system (which one?) on the internal mSATA SSD 32GB?
  This mSATA SSD is used for caching (hybrid boot) to start Windows faster 8.

  I recommend you to install the second operating system on the HARD drive.
  To do this you must create the new partition that could be used for the installation of the OS.

  Then boot from the Windows installation disc and install the OS 2nd on the new partition.

• Step by step how to set up bios to boot XP Lenovo 3000 K series?

  Hi all

  IM has been trying for several days to install xp on my PC, but it does not work. Ive also tried to install recovery DVD that Ive got with the PC but each time it seems same message that Ive had a problem with my HDD and the fourth to solve the problem in the BIOS. I tried Hurd, but no luck. I know that I've to change the AHCI RAID but I can't find this option in the BIOS.

  I have to please anyone can give a step by step how to set up bios to boot XP on Lenovo 3000 K Series.

  Thanks in advance.

  Hello

  Ive solved the problem by removing the battery for a few minutes clear the BIOS.

• Portege A100 PPA10A - update the BIOS to boot from a USB device

  Hello

  I have an old Portege A100, model: PPA10A-0002LP, but I can't seem to find this model on any Web site of Toshiba, closest I've seen is the "PPA10A - 0002 L'.

  I am wanting to know if there is a BIOS update that will allow me to boot from a USB device.

  The question I have is that I need to reinstall Windows, but the CD ROm cannot read disks.
  This network PXE boot, but I'm new to this sort of thing and have absolutely no idea what to do here.

  Any help would be great,

  Thank you

  Hello

  Portege A100 seems to be developed solely for the Australian market.
  As you say it is a model number Portege A100 PPA10A - 0002L listed on the Australian page of Toshiba Portege A100 PPA10A-0002LP belongs to the same series which is PPA10A
  So in my opinion, the BIOS should work too.

  Anyway, I doubt that the BIOS update will add boot options.

  Usually the BIOS supports booting from CD/DVD drive, drive HARD, LAN and USB FDD.
  It should be possible to boot from a boot disk using a USB FDD drive.
  I doubt you'd be able to boot from USB WEIRD since this Portege A100 supports an internal CD/DVD drive.

• Satellite P840 - Accessin the Bios or boot boot order

  Howdy all, first post here.

  I have a Satellite P840, part PSPJ6A - 00 h 001

  Windows 8.

  I have difficulties to access the Bios or boot order. I need to boot from a CD/DVD and I can't go in the boot options to change the boot order.

  I tried F12 F2 repeatedly pressing boot, pressing F12 and hold for 1 second (according to the manual) with no luck.

  What Miss me... I've never not been able to get start options before. The only thing is that it is Win8 which I am not familiar with.

  Any suggestion would be appreciated.

  Thank you

  Perform the shutdown complete http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm, restart the laptop press F12 and you will be able to enter the boot menu. Here you can choose which device should be the first boot device.

• I restart the computer and changed the BIOs to boot from the CD. So as usual, I'm prompted to press any key to start from the CD or DVD.

  Hello Comunity Microsoft :D My name is Mike and I built a gaming pc. Everything was going well for the first 3 days, but now I have a few crashes very violent. Speakers in loop and buzz and screen lock. I have to completely shut down to go back to a working state. I did everything I could possibly think of to solve this problem, but I can't.

  Then. on the problem. Today, I decided that I was able to solve all the problems by reinstalling windows. I had my keys together and put the disc in. I restart the computer and changed the BIOs to boot from the CD. So as usual, I'm prompted to press any key to start from the CD or DVD. I do and I get normal loading windows files, and at the end of this road, I get the Welcome screen in windows7 with no option and a fat slider. I don't have the little box that tells me that I can fix my computer or reinstall windows, NOTHING. I tried several times and received the same result<--(Insanity: root="" meaning...="" just="" saying)="" so="" i="" called="" windows,="" or="" had="" windows="" call="" me="" rather,="" and="" the="" tech="" says="" she's="" never="" heard="" of="" such="" a="" thing="" happening,="" and="" walked="" me="" through="" all="" these="" steps="" that="" i="" have="" already="" tried....="" still="" no="" help.="" so="" i="" am="" asking="" the="" community.="" has="" this="" ever="" happened="" to="" you="" and="" how="" did="" you="" make="" it="" work.="" and="" please="" don't="" post="" a="" list="" of="" regurgitated="" back="" log="" fix="" lists.="" rest="" assured="" i="" have="" already="" done="" it="" and="" failed="" to="" receive="" a="" different="">

  Just to isolate the problem, try to download a new copy of Windows 7, and then try again:

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  Regarding problems with the computer itself, try to disconnect all nonessential equipment attached to it to see if the problem persists.

  I would also try switching around components such as modules of memory to see if the problem persists.

  I would also check to make sure that all components are mounted and installed correctly.

• HP Pavilion touchsmart 14 n04: how to disable the bios password

  1.i do not know how to disable bios password help me please.

  I remember my bios password, but I am not as he asks me if I opened my HP

  my hp Pavilion touchsmart 14 n042tx product

  2.i have to donwgrade 8 window to window 7 help me if I want to switch to the window 8. I lose window8 CD

  thx a lot

  Hello

  You can remove the need for a power on password as follows.

  Shut down the laptop.  Now on TAP the ESC key as soon as you press the power button to access the start menu, then select f10 to open the Bios menu.  Use the arrows to select the Security tab and press ENTER.  Use the arrow keys again to highlight the power on password and press ENTER.  Enter the current password and then the new password, simply leave this blank and press on enter - do the same for the confirmation field.  Press f10, select this option to save the new settings and press to enter.

  What about being able to reinstall Windows 8, you can order a replacement set of recovery media - see the following link for more details.

  Order HP recovery disks.

  Kind regards

  DP - K

• Set the Bios password in x 230 (Windows)

  Hello

  Anyone know how I can configure the Bios from Windows 7 password? (Not in the Bios setting). I have several hundreds PSES and laptops need installation so I don't want to enter a BIOS setup.

  Thanks in advance for everyone to help.

  Can't do.  You can change a BIOS password, but you cannot set a password when one does not already exist.  This is for security reasons.  Otherwise, you may have malware that is able to set a password for the unknown and essentially brick your system.

• HP Envy 13-d053sa: update the bios

  When I rebooted my laptop today (10 June 2016), it displays a message saying that the BIOS has been updated but could not proceed because the machine was not connected. I plugged in and let it continue. Now my fingerprint reader stopped working again!... I had to re - load Win10 recently to make it back after a corruption of the registry and I don't want to have to re - load again so what can I do to recover my fingerprint reader? Thank you.

  Solved.

  I went to the control panel and the updated driver, and now it works again.