transmission tunnel (and receive) statements of bandwidth

Similar Questions

• DMVPN Tunnel and EIGRP routing problem

  I have redundant paths to a remote 2811 router on my network of sites.  The first links is a T1 frame relay connection that has been in place for years, and the new link is on a 54 Mbps fixed wireless that was recently created.

  I'm under EIGRP to my process of routing protocol 100 for the two links.

  I installed a DMVPN Tunnel between the remote 2811 and no. 2851 router on my host site.  The tunnel interface shows to the top and to the top of both sides and I can ping the IP remote tunnel of my networks side host.

  However my eigrp routes are not spread over this new tunnel link and if I run a command show ip eigrp neighbor on each router I show only the neighbor for the frame relay link and not the new wireless link.

  What I'm missing here?

  A tunnel0 to see the shows the following:

  Tunnel0 is up, line protocol is up
  Material is Tunnel
  The Internet address is 10.x.x.x/24
  MTU 1514 bytes, BW 54000 Kbps, DLY 10000 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  KeepAlive not set
  Tunnel source (FastEthernet0/1), destination 172.x.x.x 10.x.x.x
  Tunnel/GRE/IP transport protocol
  Key 0x186A0, sequencing of the people with reduced mobility
  Disabled packages parity check
  TTL 255 tunnel
  Quick tunneling enabled
  Tunnel of transmission bandwidth 8000 (Kbps)
  Tunnel to receive 8000 (Kbps) bandwidth
  Tunnel of protection through IPSec (profile "CiscoCP_Profile1")
  Last entry of 00:00:01, exit ever, blocking of output never
  Final cleaning of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 947
  Strategy of queues: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bps, 0 packets/s
  5 minute output rate 0 bps, 0 packets/s
  packages of 880, 63000 bytes, 0 no buffer entry
  Received 0 broadcasts, 0 Runts, 0 Giants 0 shifters
  errors entry 0, 0 CRC, overgrown plot of 0, 0, 0 ignored, 0 abort
  output of 910 packages, 81315 bytes, 0 underruns
  0 output errors, 0 collisions, 0 resets interface
  unknown protocol 0 drops
  output buffer, the output buffers 0 permuted 0 failures

  Please go ahead and add a static route on the hub, so it goes through the wireless link and let me know if everything works correctly.

  Federico.

• OME does not receive details of the inventory and the State for some devices

  OME does not receive the details of the inventory and the State for some servers.

  For example when looking at one of our PowerEdge R620s is all that presents itself:

  

  iDRAC firmware and LCC is updated (version 2.21.21.21 is installed.)

  I reset the iDRAC, and that did not help.  I have no problem with most of the other R620s in the same range of discovery.

  I deleted the object to OME and re-discovered twice over the past week it but did not help.

  Things seem ok when I use the troubleshooting tool:

  

  Anyone has any info on what may be going on here or how to fix this?

  Thank you

  Hello

  Thanks for the details in the post.

  Wanted to check what version of OME use you - OME 2.1?

  If so, this behavior with ws - man discovery could potentially due to expiry of certificate on this device. You can launch the iDRAC user interface and confirm the certificate information.

  2.1 the OME, the WS - Man communication component is updated. The most recent component does not communicate with the device if that device has been exceeded in the certificate.

  Sslresetcfg running via racadm will reset the certificate. For details and solution, see same threadhttp://en.community.dell.com/techcenter/systems-management/f/4494/t/19653767 .

  Let us know if that helps.

  Thank you
  Vijay

• How do you transmit and receive using a single attena with USRP

  Hello world

  I want to do a reader RFID with USRP. I want to send a signal to activate at the first and then RFID tag receive and decode the signal reflected by the tag. As I know, there are two interface RF on the USRP daughter card, I can send and receive signals using two attenas. But how can I pass the activation signal and receive the signal of the Reflection using an attena?

  Thanks in advance

  Hi 0711,

  If you use the TX/RX port, you should be able to transmit and receive using the same antenna.  But it requires more setup code.  You should have at least 2 loops in your code - one running a RX session and another execution of a session of TX.  You can use the 'End of data?' option on the niUSRP Data.vi of Tx write as a way to send your data without having to start and stop the session every time.  In order to obtain the flow of data between the session RX and TX session, I used queues.

  I worked to put together an example that illustrates the basic architecture that is required to run an application like this.  This example is not polished or finished, but I've seen some requests for how to do this, then I'll post to give you are the point of departure.  Please note that this code still has problems that need to be debugged and addressed.  It is simply intended to show how to use the end of the data? option to enable transmission shrapnel while receiving data on the same antenna.  If you set the TX1 and RX2 antennas use a loopback configuration, you can also use this code with a USRP.  Hope this helps and ask questions please.

• I have Error 0x800ccc0f and 0x800ccc79 codes then send and receive messages on outlook express.

  WHEN I TRYING TO SEND AND RECEIVE E-MAILS VIA OUTLOOK I GET ERROR MSGS. AS 'THE TCP/IP (S) CONNECTION WAS INTERRUPTED UNEXPECTEDLY BY SERVER' (ERROR No. 0x800ccc0f and 0x800ccc79 S.) MY PROTOCOL TCP/IP IN MY LOCAL AREA CONNECTION SAYS "OVER MY LAN CONNECTION SAYS"WINDOWS MANAGEMENT INSTRUMENTATION (WMI) INFORMATION MAY BE DAMAGED. " (1) (_1_) IS WHAT THE CAUSE, AND (2) WHAT ARE THE FIXES. P.S. I CAN ACCESS MY EMAIL VIA WEBMAIL FROM MY ISP.

  Original title: Outlook TCP/IP connection problems

  Hi TOMJR_3385,

  Thanks for keeping us posted and share this information with us.

  Please answer these questions-

  (1) what exactly happens when you try to access the internet?

  (2) don't you do a system restore?

  (3) that you get an error message or error code?

   

  I would like more information about the issue.

   

  Method-

  If you did not do a system restore, then you will need to perform one to cancel changes made to the computer.

  Check out the link-

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

   

  Note: Perform a system restore will cancel all changes made previously on your computer. You may also lose unsaved information as well. Proceed at your own risk.

  In addition, see the article-

  Error messages when you send and receive in Outlook and Outlook Express

  http://support.Microsoft.com/kb/813514

   

   

  Do get back to us and let us know if the steps of troubleshooting in help section. We will be happy to help you if you need help.

  Thank you.

   

   

• Try to update XP Pro sp3 and receive 0x8024400A error message

  Trying to update XP Pro sp3 and receive error 0x8024400A service package need to run MSE.  I'll have to do this because my computer has been infected by win32/caphaw.h!

  Original title: urgent update problems!

  Hello

  1 did you change on your computer before this problem?

  2. this problem occurs only with this particular update?

  You can follow the suggestions and check out them.

  Method 1

  You can run a full antivirus scan by using the Microsoft Safety Scanner.

  Microsoft safety scanner

  http://www.Microsoft.com/security/scanner/en-AU/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again. He also does the disk check, and you may lose the amount of data.

   

  Method 2

  You can follow the procedure in the article.

  Temporary connection related errors may occur when you use Windows Update or Microsoft Update

  http://support.Microsoft.com/kb/836941

  Note: Software antivirus and firewall can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attack.

   

  Method 3

  You can follow the procedure in the article.

  How to troubleshoot an installation fails on Windows XP Service Pack 3

  http://support.Microsoft.com/kb/950718

  Note: Software antivirus and firewall can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attack.

   

  Method 4

  Step 1: Place the computer in a clean boot state. How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  a. click Startand then click run.

  b. type msconfigand click OK.
  The System Configuration utility dialog box appears.

  c. click on the general tab, click Normal Startup - load all device drivers and servicesand then click OK.

  d. When you are prompted, click restart to restart the computer.

   

  Step 2:

  Download and install SP3 manually.

  Windows XP Service Pack 3 network installation Package for IT professionals and developers

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24

  See also:

  Steps to take before you install Windows XP Service Pack 3

  http://support.Microsoft.com/kb/950717

  How to obtain the latest Windows XP service pack

  http://support.Microsoft.com/kb/322389

• NAT VPN tunnel and still access Internet traffic

  Hello

  Thank you in advance for any help you can provide.

  I have a server with the IP 192.168.1.9 that needs to access a subnet remote from 192.168.50.0/24, through the Internet.  However, before the server can access the remote subnet, the server IP must be NAT'ed to 10.1.0.1 because the VPN gateway remote (which is not under my control) allows access to other customers who have the same subnet address that we do on our local network.

  We have a 2801 Cisco (running c2801-advsecurityk9 - mz.124 - 15.T9.bin) set up to make the NAT.  It is the only gateway on our network.

  I have configured the Cisco 2801 with the following statements of NAT and the relevant access lists:

  access-list 106 allow host ip 192.168.1.9 192.168.50.0 0.0.0.255

  NAT extended IP access list
  refuse the host ip 192.168.1.9 192.168.50.0 0.0.0.255
  deny ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
  ip permit 192.168.1.0 0.0.0.255 any

  route allowed ISP 10 map
  corresponds to the IP NAT

  IP nat EMDVPN 10.1.0.1 pool 10.1.0.1 netmask 255.255.255.0
  IP nat inside source list 106 pool EMDVPN
  IP nat inside source map route ISP interface FastEthernet0/1 overload

  When the server (192.168.1.9) attempts to ping on the subnet of 192.168.50.0/24 devices, the VPN tunnel is established successfully.  However, after that, the server is no longer able to access the Internet because the NAT translation for 192.168.1.9 has changed since the external IP address of the router (FastEthernet0/1) at 10.1.0.1.

  The documentation I've seen on the site of Cisco says that this type of Setup allows only host subnet communication.  Internet access is not possible.  However, maybe I missed something, or one of you experts can help me.  Is it possible to configure the NAT router traffic destined to the VPN tunnel and still access the Internet by using the dynamic NAT on FastEthernet0/1?

  Once again, thank you for any help you can give.

  Alex

  Hello

  Rather than use a pool for NAT

  192.168.1.9 - 10.1.0.1 > 192.168.50.x

  ACL 102 permit ip 192.168.1.9 host 192.168.50.0 0.0.0.255

  RM-STATIC-NAT route map permit 10
  corresponds to the IP 102

  IP nat inside source static 192.168.1.9 10.1.0.1 card expandable RM-STATIC-NAT route

  ACL 101 deny host ip 192.168.1.9 192.168.50.0 0.0.0.255
  ACL 101 by ip 192.168.1.0 0.0.0.255 any
  overload of IP nat inside source list 101 interface FastEthernet0/1

  VPN access list will use the source as 10.1.0.1... *.

  Let me know if it works.

  Concerning

  M

• BlackBerry Smartphones transmit and receive went faulty but phone calls will be text. Clicking on the loudspeaker sound

  A sudden power outage hit my Curve 8900

  When answering an incoming call or outgoing call is made the exit turns into a clicking noise that is regular and breaks the sound out and the transmission of the caller's voice in.

  They cannot hear me and hear clicks and my broken voice

  I do not have them and all I hear is the click and their voice broken up.

  The strange thing is the phone sends and receives SMS text perfectly.

  I checked this point with my service proivder o2 and they recommended an update of firmware

  So I did and updated all the software and the fault remains.

  I have a lot of mp3 music on the phone and everything is working as is the camera and video.

  Pulling the battery is not a cure.  Remove the SIM card has no cure.

  Free space is 134 MB

  Media card has 2.7 GB of free

  I have only 9 applications on the phone. Ordinary things like voice transmitter calculator

  There is one strange notification slightly to the right of where a text message is waiting for my reading, but there are no messages in folders.  Saved messages are empty, but I can't read the message and the icon will not go away.

  O2 said that I might have to send it back for repair if the stuff I try do not heal.

  I have not dropped the phone or had of infiltration water etc.  He just started to do this when the fault I

  accidentally pressed a button which started an activation of voice command and he left while I don't use voice dialing of activation.   There is no mms on hold or waiting for reading or sending sms.

  A total mystery.  Anyone got any ideas as to what might be causing this interruption of strange regular beats of the transmission of two ways?

  --

  Plado

  This is usually caused by a defective headphone plug or dirty. Inserting and removing the card several times can repair but also could reproduce. He can't. If it happens again try plugging it disconnected again and again. If that doesn't fix it, you need to repair/replace.

• Windows 7 BSOD and receiver code error BCCode: 9f

  Original title: Windows 7 BSOD
   
  Hey guys I just built my first system and it was a lot. I used the trial version of Windows 8 64-bit for about a week I had to wait for my windows 7 to arrive. Windows 8 everything went fine with no problems. Then I installed windows 7 and ever since then, every time I leave my system alone for an hour or two, I'll be back to see that it crashed because of this error message below. Can I use my computer all day, video, editing, etc, but when I close all and leave for an hour, I'll be back to see that I have broke down. I try to leave it overnight to install my steam on games but crashes after about an hour.
  Any help would be great.
  Error message:
  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.256.48
  Locale ID: 1033
  More information about the problem:
  BCCode: 9f
  BCP1: 0000000000000003
  BCP2: FFFFFA80070A4A10
  BCP3: FFFFF800047C43D8
  BCP4: FFFFFA80097AB010
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1
  Files helping to describe the problem:
  C:\Windows\Minidump\122112-20077-01.dmp
  C:\Users\Ryan\AppData\Local\Temp\WER-58203-0.SysData.XML
  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409
  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt
  Data sheet:
  Intel i5 3570 k @3.4 ghz
  Cooler Master Hyper 212 Evo
  Z77 UD5H Gigabyte motherboard
  EVGA Gtx 670 FTW
  Corsair Vengeance 8 GB 1600
  Corsair HX 750w PSU
  Seagate Barracuda 7200 rpm 1 TB
  Cooler Master Storm Stryker
  Edit: I thought it might have something to do with memory, so I ran Memtest 86 + 4 hours and had no error: P

  Hello

  Thanks for posting your query in Microsoft Community!

  According to the description, you are receiving BSOD (Blue Screen of Death) and receive the error code BCCode: 9f.

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following question:

  Did you do changes on the computer before the show?

  I suggest to follow the steps of the items listed below and check if it works.

  Error message when you try to resume a Windows 7 or Windows Server 2008 R2 to Hibernate computer-based: "Stop 0x0000009F"

  http://support.Microsoft.com/kb/977186

   

  Stop error when you upgrade a computer that is running Windows 7 or Windows Server 2008 R2 standby or into hibernation, or when you restart the computer: "0x9F".

  http://support.Microsoft.com/kb/975599

   

  stop "0x0000009F" error message when a computer enters and fate of putting into hibernation in Windows 7 or Windows Server 2008 R2

  http://support.Microsoft.com/kb/981848

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• I volunteer for installation of the Government in New Orleans.  I'm helping recommendations on equipment and software.  Their editing computer cannot be connected to the Internet.  How to buy and receive the software and updates?

  I volunteer for installation of the Government in New Orleans.  I'm helping recommendations on equipment and software.  Their editing computer cannot be connected to the Internet.  How to buy and receive the software and updates?

  Please see this link in the topic "successful."

  Creative cloud using Enterprise | Applications and updates

  You can use managed delivery of applications for the following:

  • If you need to exercise strict control over the applications installed on client computers.
  • If end-users have administrator privileges on the computer.
  • To reduce Internet bandwidth consumption by preventing multiple downloads of self-service.
  • If there is no Internet access on client computers.

• Is it possible to send and receive RTP streams on the same computer?

  Hi all
  
  I tried sending an RTP stream and receive it on the same computer, but it did not work. I use the AVTransmit2 and AVReceive2 classes, I assumed that these classes are popular, so I have not included the code for them) for this.
  
  It works perfectly fine when a computer sends using AVTransmit2 and another receiver using AVReceive2. However, when, on the same computer, I get the following error in AVReceive2:

   Cannot create the RTP Session: Unrecognized Windows Sockets error: 0: Cannot bind 

  The address I used for transmission and reception is: 224.144.251.104/22200
  
  And I also discovered that it IS possible to send and receive streams on the same computer using JMStudio, but I found it very hard to dissect its code.
  How can this be achieved using these two classes, that is, the AVTransmit2 and the AVReceive2?
  
  Any suggestions will be greatly appreciated.

  private String createTransmitter() {
  ...
  localAddr = new SessionAddress( InetAddress.getLocalHost(), port);
  destAddr = new SessionAddress( ipAddr, port);
  

  You can do this instead:

  localAddr = new SessionAddress( InetAddress.getLocalHost(), SessionAddress.ANY_PORT);
  

• IF and ELSE statements

  The man... I'm so close to figure this out and I didn't have to go back on the forum for this because I had a few topics here already when I started this project and to halfway through it and now towards the end of it, LOL! I hope that you all don't mind!
  
  in any case...
  
  Now I am trying to get users to fill out 4 boxes with the correct information, then press the ENTER key to go to the next section. Everything works perfectly with this part of my code, however, it is the part on whether they enter the wrong info that I be puzzled over.
  
  I tried the ELSE statements and various forms of listeners and IF statements, but I can't seem to make it work.
  
  When they enter the wrong info, in the entry boxes, I have to be taken to a different image. I had a script in there little worked, but instead of him awaiting until they entered all the information, it would just automatically go to the 'wrong' because technically, they received only a chance to enter the first letter of the first word.
  
  in any case, the code that I use now is attached. It works very well except the part of the erroneous info being entered. If a user has just this framework (where the code is located) and hits ENTER, thn, they are taken as part of 'Wrong', which is good, because technically they do not capture in 4 boxes. But. If they start typing in a box and then press ENTER, they need the same "Incorrect" framework because they have not all enter, but it is not that. Even if they conclude each info box and a letter is missing for example, which is wrong and should go to this 'Wrong' page, but is not.
  
  Any ideas?

  It is strange.so your code looks like this (and all the other stuff that was already there?):

  If (Key.isDown (Key.ENTER)) {}
  trace ("talk to the hand, because I'm no longer listening.");
  Key.removeListener (listener);
  trace ("the time it was the Enter key, then I should evaluate.");
  Evaluate();
  }

  It should work. I just tested it and it works for me. Well, it worked on the second try, the first time that I misspelled "listner", so be sure that you have spelled everything correctly!

  Unless you are sure that it is the function of battery called? How do you know? Y at - he got another code which could be initially move the playback cursor?

  BTW, if you use Actionscript, you shouldn't use scenes. There are strange things that occur with it and it is not worth!

• I have FaceTime disabled through restrictions on my daughter's phone.  However, she is still able to make and receive calls FaceTime. If it is limited, how this phenomenon is happening and is there a way to prevent it from happening in the future?

  I have FaceTime disabled through restrictions on my daughter's phone.  However, she is still able to make and receive calls FaceTime. If it is limited, how this phenomenon is happening and is there a way to prevent it from happening in the future?

  How do you know that she can always use Facetime?

  Could she learned/guessed the password restriction?

• Thunderbird ceased to send and receive with the new update of Windows 10.

  Thunderbird ceased to send and receive e-mail. When I tried to send I got: "the message send failed.
  The message cannot be sent because the connection to the Outgoing server (SMTP) smtp.comcast.net was lost in the middle of the transaction. Try again. "My email loads on my tablet is not comcast. Firefox works is not my internet. Clues?

  Please start * Windows * safe mode with active network
  -win10 http://windows.microsoft.com/en-us/windows-10/change-startup-settings-in-windows-10
  Always in Windows safe mode, start thunderbird in safe mode
  - http://support.mozillamessaging.com/en-US/kb/safe-mode

  Problem disappear?
  Just reply to inform us of the results.

  Do you have non-comcast accounts where this does not happen?

• Can I send and receive emails with Firefox?

  Can I send and receive emails using firefox?

  Firefox is not messaging components, but you can use webmail on sites like Yahoo! Mail and Gmail.

  Or you can use Thunderbird. https://www.Mozilla.org/en-us/Thunderbird/